Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solid additive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Evaluations of the Fates of Alkali Metals, Actinides, Mercury, and Iodine During DWPF Recycle Diversion

The fates of alkali metals, actinides, mercury, and iodine in the Defense Waste Processing Facility Recycle Diversion process (as currently conceptualized) have been evaluated through paper studies based on available knowledge of the chemistry, physical properties, solubility, and volatility of the various species involved. The effect of pH in the range from 9 to 13 has been discussed. Recommendations for additional studies to close technology gaps have been provided, many of which are contingent upon the results of pending testing and sample characterization efforts. There is uncertainty in the amounts of soluble actinides passing through the process filter, though the bulk of the actinides should be captured on the filter with the Recycle Collection Tank solids and the total amounts of actinides should be relatively low. The Recycle Collection Tank pH could impact the fraction of actinides reaching the evaporator, but the primary factors determining the actinide fate are expected to be the amount of CO 2 sorption from air sparging or, for certain actinides (such as plutonium), oxidation and/or sorption to MnO 2 solids from permanganate additions to destroy the glycolate anion. Process optimization could minimize the amounts of actinides passing the filter. Depending upon the levels of mercury observed in recycle stream samples and because of the volatility of mercury, the evaporator should be designed with the capability to remove dense mercury phases from the condensate to avoid exceeding ETP WAC limits. The facility design must be adequate to transfer dense mercury phases and testing to confirm mercury transfer is needed. Simulant containing mercury is recommended for both filtration and evaporation testing. OLI Modeling of the various recycle streams is recommended to provide insight on the fate of iodine. Iodine-spiked simulants are recommended for upcoming evaporation tests. The pro) ect should consider the likelihood and impact of NAS scale formation in the evaporators. Process optimization may be needed to minimize the accumulation of NAS scale and possibly the sorption of actinides in the evaporator. Actual waste testing of the Recycle Diversion filtration and evaporation should include the analysis of actinides, mercury, and iodine to determine their partitioning.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Fundamental Thermodynamic, Kinetic, and Mechanical Properties of Lithium and Its Alloys

Lithium alloying reactions are beneficial in promoting uniform plating and stripping of lithium metal in all-solid-state batteries. First-principles calculations are performed to predict thermodynamic, kinetic, and mechanical properties of lithium and several important Li–M alloys (M = Mg, Ag, Zn, Al, Ga, In, Sn, Sb, and Bi). While the Li–Mg binary system forms a solid solution, most other lithium–metal alloys prefer stoichiometric intermetallic compounds with common local motifs that enable fast Li diffusion. Lithium and Li-rich alloys exhibit an unusually flat energy landscape along paths that connect BCC to close-packed structures like FCC and HCP, with important implications for mechanical properties. Very low migration barriers for Li diffusion that rival those of superion conductors are predicted, both in pure Li and in Li–M intermetallics. However, vacancy concentration, which is crucial for substitutional diffusion, is predicted to be low in metallic Li and most Li–M intermetallics. Compounds such as B32 LiAl and LiGa as well as D0 3 Li 3 Sb and Li 3 Bi exhibit structural vacancies at higher ends of their voltage windows, which together with low migration barriers leads to exceptionally high Li mobilities. In the Li–Mg solid solution, the addition of Mg is found to decrease the vacancy tracer diffusion coefficient by an order of magnitude.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Understanding implications of cathode architecture on energy density of solid-state batteries

Next generation solid-state batteries (SSB) will need to leverage high voltage cathodes, as well as metallic anodes to achieve the realistic performance targets necessary to replace liquid electrolyte-based batteries in cutting-edge applications including electric vehicles. However, limitations arising from mass and charge transports, kinetics and chemo-mechanical degradation at the electrode | electrolyte interface limit the performance of present day SSBs. Optimizing composite cathode architecture, which is an integral part of solid-state batteries, is vital to realize the high-energy density and high-performance goals for next-generation solid-state batteries. Additionally, cathode architecture needs to be optimized for high loadings of active material, well-percolated ion and electron transport pathways and increased resilience against electrochemical stresses. This paper provides a first report of framework for geometric modeling of composite cathode architectures and evaluates the impact of cathode architecture on cell-level energy density using hierarchical models. Packing around primary and secondary active material particles are simulated for a range of active material particle size and solid electrolyte size distributions in the composite cathode. Impact of packing architecture on processing parameters of a given cathode composition and thickness, as well as on achievable energy density is evaluated for a range of commonly used solid electrolyte and cathode materials. Overall, the proposed framework offers a facile exploratory methodology for establishing initial metrics for scalable processing of practical and competent SSBs.

25 ENERGY STORAGE↗
DOE OSTI2022

An Innovative Zero-Liquid Discharge Intermediate-Cold-Liquid Eutectic-Freeze Desalination System

A novel freeze desalination technology is presented for purification of water produced from various industrial processes, including oil and gas extraction. The main innovative idea is introducing a water-immiscible intermediate-cold-liquid (ICL) medium which absorbs the cold from a refrigeration cycle and transfers it to a freezing chamber where it is mixed with brine. The cold ICL enters the freezing chamber at temperatures between -10°C to -30°C. Precooled brine in injected into the freezing chamber and pure water freezes out of the brine upon mixing with the ICL. The rate of freezing inside the chamber is controlled by adjusting the flow rate of the cold ICL relative to the inlet brine. Both eutectic freeze and non-eutectic freezing are possible by controlling the temperature of the freezing chamber. The solid-liquid slurry created in the freezing chamber flows to a filter separation unit after passing through a separation column. The ice crystals are separated from the liquid by a rotary filter device. The collected ice is rinsed by a centrifugal unit. The rinsed ice is melted to produce fresh water. The developed technology resolves the issues common to current freeze-desalination systems while offering superior heat transfer performance ascribed to direct-contact between the cooling medium and the brine in addition to producing solid salt and pure water. The system operates under atmospheric pressure. The low operation temperature minimizes the corrosion issues common in systems exposed to brine. Also, due to the low operating temperature, there are no concerns about evaporation of volatile organics from the produced water during the treatment. The developed technology effectively eliminates the use of chemicals for pretreatment of brine. The system can be constructed from commercially available components. Extensive testing using a lab-scale prototype by using synthetic brine and actual produced water with TDS values from 50,000 ppm to 300,000 ppm showed that freshwater could be achieved with relatively small dependency on the quality of the input brine. The quality of the treated water was found to be mainly a function of the duration of the centrifugal process. Treated water with TDS as low as 200 ppm could be achieved in the tests. Thermo-economic modeling coupled with system level thermochemical process model were developed for prediction of the LCOW. The LCOW was predicted to be $\$$0.50 to $\$$0.90 per barrel of produced water. The potential markets for deployment of the technology are the oil and gas, in-land thermoelectric powerplants, RO desalination plants, and mining industry.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

Sintering-based Metal Additive Manufacturing Methods for Magnetic Materials

In this chapter, we review the relationship between solid-state sintering and additive manufacturing (AM) methods for fabricating soft and hard magnetic materials. Heat treatment as a post-processing method has been done in conjunction with AM as a method to improve density and/or mechanical properties. In binder jetting (BJT) of metal powders, sintering is a crucial post-processing step and is necessary for obtaining the final product. This is because the parts are only in the “green” state when they leave the BJT printer, with poor mechanical properties and high porosity. Sintering densifies and strengthens the green part into the final product. A potential industrial application for sintering-based AM is the fabrication of magnetic materials. The motivation for doing so, the process and properties of the AM magnets, and the potential applications of post-sintered AM magnets are explored.

Wang, Haobo↗
DOE OSTI2024

Additive manufacturing of multiscale NiFeMn multi-principal element alloys with tailored composition

Nanostructured multi-principal element alloys (MPEAs) have been explored as next-generation engineering materials due to unique mechanical and functional properties which have significant advantages over traditional dilute alloys. However, the practical applications of nanostructured MPEAs are still limited due to the lack of scalable processing approaches to prepare a large quantity of nanostructured MPEAs, as well as lack of an efficient pathway for high-throughput discovery of better functional nanostructured MPEAs within their vast compositional space. Here we tackle these challenges by presenting an integrated approach by combining direct-ink-writing-based additive manufacturing, solid-state sintering, and chemical dealloying to manufacture hierarchically porous MPEAs. The hierarchical structure is comprised of macro- and micro-scale pores introduced via extrusion printing and polymer decomposition during sintering, as well as nanoscale pores formed via chemical dealloying. The macro- and micro-scale pores allow efficient dealloying of a large mass of material as the diffusion length that the corroding medium must penetrate remains at the scale of the ligaments formed after sintering (∼10 μm), despite the large volume of the 3D-printed samples. In addition, this integrated approach enables versatile control of the alloy composition via precisely tuning the ratio of elemental powders in the starting ink, thus offering a pathway for high-throughput discovery of novel functional MPEAs. As a case study, multiscale macro/micro/nanoporous NiFeMn MPEAs with three different compositions were investigated as catalysts to reduce the overpotential of oxygen evolution reaction (OER), where NiFeMn-based electrocatalysts display composition-dependent performance such that the overpotential measured at a current of 0.5 A g −1 for OER increases in the order of Ni 58 Fe 29 Mn 13 ⩽ Ni 64 Fe 26 Mn 10 < Ni 76 Fe 18 Mn 6 . This introduced manufacturing process offers new opportunities for scalable fabrication and rapid screening of nanostructured multi-component complex alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

NaSICON-type materials for lithium-ion battery applications: Progress and challenges

Lithium-ion batteries (LIBs) are widely used in electric vehicles, energy storage, smart grids, and portable devices due to their high average output voltage and energy density. NaSICON-type materials have been identified as potential candidates for electrode and solid electrolyte materials for LIBs due to their 3D framework, which contains Li + ions, excellent ionic conductivity, and thermal stability. NaSICON-type materials have a 3D framework and a fast Li + diffusion pathway, making them suitable for use in LIBs. However, their application as solid electrolytes is limited due to poorer ionic conductivity and interfacial stability compared to commercialized liquid electrolytes. Furthermore, their use as electrode materials is restricted by their low electronic conductivity. Here, this review provides an overview of NaSICON-type materials, including their common structure, Li + diffusion mechanism, and preparation strategies. The article also discusses the application and modification strategies of NaSICON-type materials for LIBs, classifying them as anode materials, cathode materials, and solid electrolyte materials. Additionally, the potential use of NaSICON-type materials as modification materials for cathode materials for LIBs is briefly mentioned. Building on previous work on NaSICON-type materials, we propose potential areas for further development and wider applications of these materials in LIBs.

25 ENERGY STORAGE↗
DOE OSTI2022

Impact of feed variability on cesium removal with multiple actual waste samples from the Hanford site

Here, the Tank Side Cesium Removal (TSCR) system, under development by Washington River Protection Solutions (WRPS), will send initial low-activity Hanford waste tank supernate feeds to the Hanford Waste Treatment and Immobilization Plant (WTP) Low-Activity Waste (LAW) Facility. In addition to entrained solids removal from the supernate, the primary goal of TSCR is to remove cesium-137 ( 137 Cs) by ion exchange, allowing contact handling of the liquid effluent product at WTP. Crystalline silicotitanate (CST) ion exchange media, manufactured by Honeywell UOP (product IONSIV™ R9140-B), was selected as the ion exchange media at TSCR. This lot of material was found to have superior performance in comparison to historic batches of CST. Ion exchange column and batch contact testing with supernate from Hanford tanks AP-105, AP-107 and AW-102 was performed to assess the impact of feed variability on system performance. These tests demonstrated that batch contact measurements provide a reasonable prediction of column capacities with some deviation in performance attributed to column dynamics. In addition, the variability in CST capacity for cesium in the various actual waste samples does not track with historical understanding of the competing cations, suggesting that tank waste samples contain other components that may significantly impact cesium loading.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Valuation of Anode Materials for High-Performance Lithium Batteries: From Graphite to Lithium Metal and Beyond

Lithium-ion batteries have revolutionized energy storage, yet advanced technologies such as electric vehicles and eVTOLs demand even higher performance and safety. Anodes, the negative electrodes, are crucial in enhancing batteries’ safety, lifespan, and fast-charging capabilities. This review paper comprehensively evaluates the progression of anode materials from traditional graphite to advanced anodes like lithium metal. Graphite anodes, with a capacity of 372 mAh g −1 , enabled the first commercial lithium-ion batteries, but future applications require higher energy densities and fast-charging capabilities. Emerging anode materials, including alloying, and conversion types, as well as lithium metal, offer significantly higher capacities, with lithium metal offering a theoretical capacity of 3 860 mAh g −1 . However, these advanced anodes face challenges such as volume expansion, high surface reactivity, sluggish Li+ kinetics, and unstable lithium deposition morphologies. Here, this review critically examines the electrochemical performance, interfacial properties, mechanical attributes, and stability issues of various anode materials. It further discusses solid electrolyte interphase (SEI) formation, strategies for enhancing interface stability, and the requirements of anodes for solid-state batteries. Additionally, the review explores potential solutions for limitations with each anode type, highlights innovative anode-free architectures, and evaluates the current and future trends of battery anode industries. Ultimately, this paper aims to guide the development of high-performance anode materials, paving the way for the next generation of efficient, reliable lithium batteries.

Alloying anodes↗
DOE OSTI2024

Surface Engineering Strategy to Synthesize Bicomponent Carbons for Rechargeable Zinc-Air Batteries

Atomic Fe-N x moieties and nanosized FeCo species anchored on carbons have each been demonstrated to be among the most effective active components for oxygen reduction and evolution reactions (ORR/OER), respectively in rechargeable zinc -air batteries (ZABs). However, incorporating both of these components in a single catalyst presents a great challenge due to the trade-off in formation between them during hightemperature preparation. Herein, we integrate them into a bicomponent carbon through a surface engineering strategy. In this process, K 3 [Fe(CN) 6 ] is engineered on the surface of a precursor mixture consisting of polyaniline-coated graphene oxide and ZIF-67. This is followed by pyrolysis to produce the bicomponent carbon catalyst of FeCo nanoparticles modified carbon polyhedron (for accelerating the OER), supported on atomically dispersed Fe -N -doped carbon nanosheet (for boosting the ORR). The catalyst exhibits a small potential gap of 0.69 V for OER/ORR. In situ Raman spectroscopy demonstrates that spinel FeCo oxides may be responsible for OER. The use of this catalyst in ZABs achieves high power densities of 225 mW cm -2 in aqueous electrolyte and 164 mW cm -2 in solid-state electrolyte. Additionally, a small and stable voltage gap of 0.712 V at 10 mA cm -2 is maintained after 1035 discharge -charge cycles demonstrating the great application potential in energy devices.

An, Jia-Xing↗
DOE OSTI2022

Sulfone-based electrolytes for high energy density lithium-ion batteries

Here, in this work, localized high concentration electrolytes (LHCEs) based on tetramethylene sulfone (TMS) were designed. Similar to LHCEs based on other solvents, TMS-based LHCEs can achieve excellent compatibility with high energy density lithium ion batteries (LIBs) when combined with a proper additive. By comparing LHCEs based on different solvents and additives, it was revealed that the unique solvation structure of LHCEs facilitates the synergetic decomposition of anion, solvent and additive in the solid electrolyte interphase (SEI) formation. Proper combinations of the three constituents of the solvation sheaths in LHCEs can promote the formation of highly effective SEI on graphite negative electrode. The absence of LiPF 6 in LHCEs also suppresses the degradation of positive electrode materials in LIBs. The superior interphasial properties of LHCEs is the key to realizing the long lifespan of high energy density LIBs.

25 ENERGY STORAGE↗
DOE OSTI2025

ReaxFF Parameter Set for Boron Clusters and Icosahedral Boron Crystals: Comparison with Density Functional Theory and Machine-Learning Potentials

Icosahedral boron materials, which include regular icosahedra of 12 boron atoms have gained increasing attention due to their potential applications as superhard materials, semiconductors, and energy storage media. However, the synthesis of high quality crystals of these materials has been a major barrier to the development of these applications. To enable computational prediction of synthesis conditions yielding high-quality icosahedral boron crystals, herein we tested and refined a set of ReaxFF parameters for the nucleation and growth of such crystals. We focused on matching the relative energies of small boron clusters obtained by density functional theory since such small clusters and similar motifs are likely present in crystal nuclei and at the interface of growing crystals. Using a training set of B 80 clusters, including a low-energy core–shell structure containing a B 12 icosahedron core and a high-energy single-shell structure produced in preliminary ReaxFF simulations, the ReaxFF parameter set was refined to better reproduce energies calculated by density functional theory (DFT). Among existing ReaxFF parameter sets and the machine-learning interatomic potentials MACE-MP-0, MACE-MP-0b3, MACE-MPA-0, PFP v7.0.0, and SevenNet-MF-ompa, only our new parameter set and PFP v7.0.0 correctly ranked these B 80 clusters. This refinement led to improved agreement with DFT for a test set of 58 clusters consisting of 8–103 boron atoms. Furthermore, our refined parameter set yielded greater local icosahedral structure than the previously existing ReaxFF parameter set for larger scale simulations of crystallization from supercooled liquid boron. Additionally, simulations of solid boron in contact with molten nickel using our refined ReaxFF parameters yielded a boron solubility value that agrees moderately well with experimental expectations, while the previous boron parameters gave a value that was much too low.

boron↗
DOE OSTI2025

Symmetry breaking forms split-off flat bands in quantum oxides controlling metal versus insulator phases

The crystal structure used as input to electronic structure calculation of conventionally bonded solids consists primarily of the standard crystallographic degrees of freedom. Quantum solids sometimes have additional microscopic degrees of freedom (m-DOF) nested within the crystallographic structure. These might include local motifs including positional (Peierls dimers, deformed octahedra, Jahn-Teller distortions), magnetic (local moment configurations) and dipolar (local ferroelectric configurations). Such motifs can be observed experimentally via local probes that avoid averaging, and theoretically as distinct total energy lowering features relative to more simplified “average crystallographic structures”. Here we examine the ability of electronic structure methods independent of strong correlation physics to explain the broad phenomenology of metal-insulator selectivity in quantum oxides by energy-lowering symmetry breaking. We do this by avoiding the restriction of considering only (i) electron-electron interactions in a fixed unresponsive lattice—as done in Mott strong correlation explanations—allowing, however, (ii) local positional and magnetic motifs that coexist within a crystallographic landscape. We find in a broad range of quantum oxides with different symmetry breaking modes the formation of split-off flat bands that can also control metallic versus insulating characteristics. The split-off band effect is common to magnetic and non-magnetic materials, including both binary and ternary oxides. One finds that when such local symmetry breaking motifs are considered in mean-field-like (e.g. density functional theory) electronic structure calculations of quantum oxides, they explain many of the observed trends in metal vs insulator phases discussed otherwise in prior literature via strong correlation in symmetry unbroken view.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

A Prototype High-Voltage Pulsed Power Supply for Control of the ITER Shattered Pellet Injection System Flyer Plate Valve

A high-voltage pulsed power supply (HVPPS) has been designed, prototyped, and tested for driving an eddy current actuated propellant valve for the International Thermonuclear Experimental Reactor (ITER) disruption mitigation system. The high-voltage (HV) dc supply output voltage is software programmable, and the energy storage capacitor bank can be readily reconfigured as 200, 400, 600, and 800 μ F, enabling testing and optimization of both the valve drive and valve systems. Multiple system parameters are monitored before, during, and after each firing of the valve. The system parameters are both displayed and stored for further analysis. Control of the setup, firing sequence, and data collection is automated using a LabVIEW-based control program. The programmability and reconfigurability of this system collectively provide a flexible and robust platform for system refinement and optimization. In this article, a summary of the system will be provided including operational sequences, HV switching and associated triggering methods and circuits, and results measured while firing a solid frozen pellet. Additionally, planned refinement activities toward meeting all requirements for ITER integration will be discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Towards Multilayered Coatings of 304L Stainless Steels Using Friction Surfacing

Abstract The objective of this work is to study friction surfacing process variability when depositing multilayered coatings. This is motivated by the need to maintain deposition quality when depositing multiple friction surfacing layers, whether for repair, remanufacturing, or new part creation using this solid-state metal additive manufacturing process. In this study, 10-mm-diameter 304L stainless steel rods were used to create up to five layers of 40-mm-long coatings on 304L substrates using a constant set of processing parameters. In-process measurement of forces (X, Y, Z), flash temperature, flash geometry, layer temperature, and post-process measurement of layer geometry, microhardness, and microstructure are used to characterize changes in the friction surfacing process as more layers are deposited. It was observed that with increasing layers: layer thickness and deposition efficiency decrease; offsetting of the deposition towards the retreating side, and temperature in the deposited layer increase; and flash temperature does not change. Metallurgical analyses of friction-surfaced cross-sections revealed fine grain refinement and transformation of base austenite to strain-induced martensite. It is concluded that the process parameters need to be adjusted even after the second or third layer is deposited, corrections to the tool path are required after a couple of layers, and the measured process forces, as well as deposited layer temperature, may be useful to monitor and control the process and its instabilities.

Engineering↗
DOE OSTI2020

FY20 SAM Code Developments and Validations for Transient Safety Analysis of Advanced non-LWRs

The System Analysis Module (SAM) is under development at Argonne National Laboratory as a modern system-level modeling and simulation tool for advanced non-light water reactor safety analyses. It utilizes the object-oriented application framework MOOSE to leverage the modern software environment and advanced numerical methods. The capabilities of SAM are being extended to enable the transient modeling, analysis, and design of various advanced nuclear reactor systems. This report summarizes major progress in SAM code development, capability enhancements, demonstration, and validation to support transient safety analysis of advanced non-LWRs. Rapid developments continued in fiscal year 2020 (FY20) to support various needs of the advanced reactor community, especially the NRC and industry on the licensing safety analysis of advanced reactor designs. Significant code changes were made to provide various capability enhancements, bug fixes, and user friendliness improvements. Major code updates are summarized in Section 1, while four important enhancements are detailed in Sections 2-5, including a multi-dimension flow model; reactivity feedback and decay heat models; control and trip system modeling, and additional fluid and solid thermophysical property models. Code validation activities in FY20 include using test data from the Fast Flux Test Facility (FFTF), the High Temperature Test Facility (HTTF), and several separate effects test facilities for pebble-bed modeling.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Reduced Temperature Cesium Removal from AP-101 Using Crystalline Silicotitanate

The Tank Side Cesium Removal (TSCR) system, currently operational under Washington River Protection Solutions LLC (WRPS), sends initial low-activity Hanford waste tank supernate feed to the Hanford Waste Treatment and Immobilization Plant (WTP) Low-Activity Waste (LAW) Facility. In addition to entrained solids removal from the supernate, the primary goal of TSCR is to remove cesium-137 ( 137 Cs) by ion exchange, allowing contact handling of the liquid effluent product at the WTP. Crystalline silicotitanate (CST) ion exchange media, manufactured by Honeywell UOP, LLC (product IONSIV™ R9140-B), was selected as the ion exchange media at TSCR. Laboratory-scale ion exchange processing using TSCR prototypic unit operations continues to contribute toward WRPS establishing accurate process flowsheets for the individual feed campaigns planned for TSCR. This report describes the small-scale ion exchange testing with 14.0 L of diluted and filtered supernate from tank 241-AP-101 (AP-101DF) at 16 °C (62 °F) to demonstrate processing at temperature conditions that are more prototypic of what the TSCR system could experience during colder seasons of the year. Since CST Cs capacity increases with decreasing contact temperature, testing at the lower operating temperature will help to predict the maximum 137 Cs loading onto the CST in the TSCR system. One of the waste acceptance criteria (WAC) for the WTP Low-Activity Waste Facility is that the waste must contain less than 3.18×10 -5 Ci 137 Cs per mole of Na. For the AP-101DF tank waste to meet this criterion, only 0.144% of the influent 137 Cs concentration may be delivered to the WTP; this requires a Cs decontamination factor of 694. Testing with AP-101DF matched TSCR prototypic operations where a lead-lag configuration was used until the lag column reached the WAC limit, then a polish column was brought online for continued processing in a lead-lag-polish column configuration. Feed was processed at 1.9 bed volumes (BVs) per hour; the flowrate, in terms of contact time with the CST bed, matched the expected flowrate at TSCR. The Cs-decontaminated product was retained for vitrification testing (to be reported separately). The lead column reached 62% Cs breakthrough after processing ~1400 BVs of feed; the 50% Cs breakthrough occurred at 1250 BVs. Testing compared to previous AP-107 testing at 16 °C showed ~80 BV increases in volume processed to reach the WAC limit for both lead and lag columns. A similar slope in breakthrough curves for both tests indicates similar kinetic behavior, with variations in feed matrices (Na and Cs concentrations) likely responsible for the deviations in reaching the WAC limit. The Cs effluent from the lag column reached the WAC limit after processing 875 BVs. Anticipating this breakthrough point, the polish column was preemptively installed at 770 BVs. Cs breakthrough from the lag column began at 300 BVs, reaching 5.32×10 0 µCi/mL, or 5.6 % Cs breakthrough, after processing all 1400 BVs of feed. Table S.1 and Figure S.1 summarize the observed column performance and relevant Cs loading characteristics.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Ion Exchange Processing of AP-105 Hanford Tank Waste through Crystalline Silicotitanate in a Staged 2- then 3-Column System (Rev.1)

The Tank Side Cesium Removal (TSCR) system, under development by Washington River Protection Solutions LLC (WRPS), will send initial low-activity Hanford waste tank supernate feeds to the Hanford Waste Treatment and Immobilization Plant (WTP) Low-Activity Waste (LAW) Facility. In addition to entrained solids removal from the supernate, the primary goal of TSCR is to remove cesium-137 ( 137 Cs) by ion exchange, allowing contact handling of the liquid effluent product at the WTP. Crystalline silicotitanate (CST) ion exchange media, manufactured by Honeywell UOP, LLC (product IONSIVTM R9140-B), was selected as the ion exchange media at TSCR. CST is a non-elutable inorganic material that has demonstrated robust chemical, physical, and radiation tolerance while maintaining functionality. However, exchange kinetics of Cs onto CST is slow, resulting in low utilization of the CST Cs load capacity before unacceptable Cs breakthrough. Two process flow designs have been tested, as follows. 1. Lead-lag column processing: The lead column was removed after the lag column effluent reached the waste acceptance criteria (WAC) limit, the lag column was moved into the lead position, and a new lag column was installed. This format used ~52% Cs load capacity on the lead column. 2. Lead-lag-polish column processing: The processing was stopped when the polish column effluent reached the WAC limit. This format resulted in 81% Cs load capacity on the lead column. Testing with diluted feed from Hanford tank AP-105 (AP-105DF) incorporated a nuanced change to the lead-lag-polish column system where the polish column was inserted when the lag column effluent reached WAC limit. A 10.9-L volume of AP-105DF (diluted to 5.6 M Na) was processed through the Direct Feed Test Platform system, established at Pacific Northwest National Laboratory to support small-scale waste qualification efforts. The columns consisted of 10-mL CST beds (CST Lot 2002009604, sieved to screen out >30-mesh particles) placed in 1.5-cm-inner-diameter columns. Feed was processed at 1.83 bed volumes (BV) per hour; the flowrate, in terms of contact time with the CST bed, matched the expected flowrate at TSCR. The <30-mesh CST sieve cut was expected to provide appropriate performance scaling to a full-height column. The installation of the polish column later in processing (after processing 523 BVs) did not appear to fundamentally change the utilization of the lead column for Cs exchange nor did it extend the total feed processing volume when compared to the previous test with AP-107 feed. Table ES.1 and Figure ES.1 summarize the measured AP-105DF Cs load performance.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗