Search NASA⌕ Search

SEARCH · Search NASA

Results for “Test methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Cartridge output testing - Methods to overcome closed-bomb shortcomings

Although the closed-bomb test has achieved virtually universal acceptance for measuring the output performance of pyrotechnic cartridges, there are serious shortcomings in its ability to quantify the performance of cartridges used as energy sources for pyrotechnic-activated mechanical devices. This paper presents several examples of cartridges (including the NASA Standard Initiator NSI) that successfully met closed-bomb performance requirements, but resulted in functional failures in mechanisms. To resolve these failures, test methods were developed to demonstrate a functional margin, based on comparing energy required to accomplish the function to energy deliverable by the cartridge.

Bement, Laurence J.↗
NASA NTRS2019

Aerodynamic Characterization and Improved Testing Methods for the Space Launch System Liftoff and Transition Environment

Low-speed wind tunnel testing for the liftoff and transition environment of the Space Launch System (SLS) was recently completed in the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel using 1.75%-scale models of three SLS vehicle configurations. During the liftoff testing, the primary objective was to evaluate the aerodynamic forces and moments on the SLS launch vehicles, as the vehicle, launch tower, and mobile launch platform were subjected to ground winds from all directions at varying heights for the vehicle off the launch pad. Additionally, aerodynamic forces and moments were acquired for all three SLS vehicles during the transition phase from liftoff to ascent that covered a wide range of angles of attack and angles of side slip. Details of the experimental setup including improved testing methods and a stiffer sting-balance system based on lessons learned from previous test entries are presented. Also, a new force measurement technique was applied during the test where two subminiature six-component load cells were installed in each Solid Rocket Booster (SRB) to acquire forces and moments for each SRB separately from the full vehicle forces and moments measured by the main strain gauge balance. Finally, sample results from the experiment are presented including improved overall data coverage, evaluation of the new SRB data, and smoke flow visualization photos.

Chan, David T.↗
NASA NTRS1989

A test method to measure the response of composite materials under reversed cyclic loads

A test method to measure the response of composite materials under reversed cyclic loads is described. The method approximates the long-term response of a component by permitting the composite specimen to respond to the imposed loads and fail in an unconstrained mode rather than in a constrained mode. The method has been successfully used for the reversed cyclic loading of unnotched and notched graphite/epoxy and graphite/PEEK laminates of various stacking sequences. Included in the paper are monotonic tensile and compressive stiffness and strength data at several points in the fatigue lifetime, and damage development information obtained via X-ray radiography for quasi-isotropic T300/5208 and AS4/PEEK laminates with unloaded circular holes.

Bakis, Charles E.↗
DOE OSTI2019

Effect of Internal Pressurization on the Creep-Fatigue Performance of Alloy 617 Based on Simplified Model Test Method

The Simplified Model Test (SMT) is an alternative approach to determine cyclic life at elevated temperature and avoids parsing the damage into creep and fatigue components. The original SMT concept [1] considered that the effects of sustained primary stress loading could be safely neglected because the allowable local stress and strain levels were much higher than the allowable sustained primary stress levels. This key assumption is critically evaluated on Alloy 617 using internal pressurized cylindrical SMT specimens at 950 °C. The impact of combined internal pressurization and displacement-controlled creep-fatigue loading on the SMT cycle life is demonstrated at different strain ranges. The effect of primary load on the SMT design method is discussed.

Wang, Yanli↗
NASA NTRS1991

Proceedings of the Advisory Committee on Standardization of Carbon-Phenolic Test Methods and Specifications

Proceedings of the Advisory Committee on Standardization of carbon-phenolic test methods and specifications are compiled. The following subject areas are covered: ashing procedures and alkali metal content of carbon fiber and fabrics; SPIP product identification code; SPIP initiative to adopt a water-soluble rayon yarn lubricant/size for weaving; fabric oxidation mass loss test; shelf life limit for prepregs, industry standard; silicon contamination update; resin, filler, and fabric content in prepreg; carbon assay testing calibration; thiokol rayon specifications; and SPIP low conductivity PAN program.

Hall, William B.↗
NASA NTRS1972

Testing methods and techniques: Quality control and nondestructive testing: A complication

A variety of devices and techniques useful in nondestructive testing is described. Ranging in complexity from an automated ultrasonic testing system designed for complex laminated honeycomb structures, to a flexible leak detector probe, the items represent either potential savings in cost and time, or improvement in inspection quality over past techniques. Data cover weld and braze inspection, leak detection, and inspection of composite materials.

Source record↗
NASA NTRS2017

Validation of Test Methods for Air Leak Rate Verification of Spaceflight Hardware

As deep space exploration continues to be the goal of NASAs human spaceflight program, verification of the performance of spaceflight hardware becomes increasingly critical. Suitable test methods for verifying the leak rate of sealing systems are identified in program qualification testing requirements. One acceptable method for verifying the air leak rate of gas pressure seals is the tracer gas leak detector method. In this method, a tracer gas (commonly helium) leaks past the test seal and is transported to the leak detector where the leak rate is quantified. To predict the air leak rate, a conversion factor of helium-to-air is applied depending on the magnitude of the helium flow rate. The conversion factor is based on either the molecular mass ratio or the ratio of the dynamic viscosities. The current work was aimed at validating this approach for permeation-level leak rates using a series of tests with a silicone elastomer O-ring. An established pressure decay method with constant differential pressure was used to evaluate both the air and helium leak rates of the O-ring under similar temperature and pressure conditions. The results from the pressure decay tests showed, for the elastomer O-ring, that neither the molecular flow nor the viscous flow helium-to-air conversion factors were applicable. Leak rate tests were also performed using nitrogen and argon as the test gas. Molecular mass and viscosity based helium-to-test gas conversion factors were applied, but did not correctly predict the measured leak rates of either gas. To further this study, the effect of pressure boundary conditions was investigated. Often, pressure decay leak rate tests are performed at a differential pressure of 101.3 kPa with atmospheric pressure on the downstream side of the test seal. In space applications, the differential pressure is similar, but with vacuum as the downstream pressure. The same O-ring was tested at four unique differential pressures ranging from 34.5 to 137.9 kPa. Up to six combinations of upstream and downstream pressures for each differential pressure were compared. For a given differential pressure, the various combinations of upstream and downstream dry air pressures did not significantly affect the leak rate. As expected, the leak rate of the O-ring increased with increasing differential pressure. The results suggested that the current leak test pressure conditions, used to verify spacecraft sealing systems with elastomer seals, produce accurate values even though the boundary conditions do not model the space application.

helium leak detector↗
NASA NTRS1986

Test Method for X-Ray Telescopes

Telescopes and X-ray telescopes in particular, tested with nearby point sources of radiation. When point-source rays enter telescope through annular entrance pupil (and under conditions of spherical aberration), ring image produced. Deviation of ring image from perfect circular shape reveals misalinements and surface inaccuracies in telescope. Although particularly suited for grazing-incidence types of systems, this test method applied to other types of optical systems.

Korsch, D.↗
NASA NTRS2007

In Situ Test Method for the Electrostatic Characterization of Lunar Dust

This paper serves to illustrate the testing methods necessary to classify the electrostatic properties of lunar dust using in situ instrumentation and the required techniques therein. A review of electrostatic classification of lunar simulant materials is provided as is its relevance to the success of future human lunar missions.

Buhler, C. R.↗
NASA NTRS1972

Ground and flight test methods for determining limit cycle and structural resonance characteristics of aircraft stability augmentation systems

Performance criteria and test techniques are applied to stability augmentation systems (SAS) during ground testing to predict objectionable limit cycles and preclude structural resonance during flight. Factors that give rise to these problems, means of suppressing their effects, trade-offs to be considered, and ground test methods that have been developed are discussed. SAS performance predicted on the basis of these tests is compared with flight data obtained from three lifting body vehicles and the X-15 research airplane. Limit cycle and structural resonance test criteria, based upon ground and flight experience and data, were successfully applied to these vehicles. The criteria used were: The limit cycle amplitude (SAS gain multiplied by peak-to-peak angular rate) shall not exceed 0.5 deg for the highest product of control power and SAS gain that will be used in flight; the maximum in-flight SAS gain should never exceed 50 percent of the value at which a structural resonance can be sustained during ground test.

Painter, W. D.↗
NASA NTRS2001

Rotary Wing Flight Test Methods Used for the Evaluation of Night Vision Devices

A number of rotary wing flight tests have been conducted by the Army Aeroflightdynamics Directorate in cooperation with NASA which involved the use of night vision devices and simulated devices. The test set up and data analysis have been taken from two perspectives. Some of the flight tests were structured to look at aircraft handling qualities when the pilot's image quality was reduced from normal daylight levels. In this case, aircraft flight path information was given to the pilot as one input into the Handling Qualities Ratings. Other flight tests were structured to look at pilot and workload directly. In this second case, aircraft position was accurately measured and used as pilot performance data. This paper provides an overview of the test methods used, lessons learned, and recommendations for future tam of night vision devices.

Haworth, Loran↗
NASA NTRS1977

Studies with the USF/NASA toxicity screening test method - Exercise wheels and oxygen replenishment

Continuing efforts to improve the University of San Francisco/NASA toxicity screening test method have included the addition of exercise wheels to provide a different measure of incapacitation, and oxygen replenishment to offset any effect of oxygen depletion by the test animals. The addition of exercise wheels limited the number of animals in each test and doubled the required number of tests without any significant improvement in reproducibility. Oxygen replenishment appears to have an effect on survival in the last 5 minutes of the 30-minute test, but the effect is expected to be similar for most materials.

Hilado, C. J.↗
NASA NTRS1978

Statistical studies of animal response data from USF toxicity screening test method

Statistical examination of animal response data obtained using Procedure B of the USF toxicity screening test method indicates that the data deviate only slightly from a normal or Gaussian distribution. This slight departure from normality is not expected to invalidate conclusions based on theoretical statistics. Comparison of times to staggering, convulsions, collapse, and death as endpoints shows that time to death appears to be the most reliable endpoint because it offers the lowest probability of missed observations and premature judgements.

Hilado, C. J.↗
NASA NTRSDate not supplied

Overview of A Survey Methods Test for the NASA Quesst Community Survey Campaign

In its mission to expand knowledge and improve aviation, NASA conducts research to address sonic boom noise, the prime barrier to overland supersonic flight. NASA is currently preparing for a community survey campaign to assess response to noise from the new X-59 aircraft. During each community survey, a substantial number of observations must be collected over a limited timeframe to generate a dose response relationship. A sample of residents will be recruited in advance to fill out a brief survey each time X-59 flies over, approximately 80 times throughout a month. In preparation NASA conducted a month-long test of survey methods in 2023. A sample of 800 residents was recruited from a simulated fly-over area. Because there were no actual X-59 fly-overs, respondents were asked about their reactions to noise from normal aircraft operations. The respondents chose whether to fill out the survey on the web or via a smartphone application. Evaluating response rates and how they evolved over time was a specific focus of the test. Also, a graduated incentive structure was implemented to keep respondents engaged. Finally, location data was collected from respondents since it will be needed to estimate individual noise exposure from X-59. The results of this survey test will help determine the design of the community survey campaign.

Sonic boom↗
NASA NTRS2009

Topics on Test Methods for Space Systems and Operations Safety: Applicability of Experimental Data

This viewgraph presentation reviews topics on test methods for space systems and operations safety through experimentation and analysis. The contents include: 1) Perception of reality through experimentation and analysis; 2) Measurements, methods, and correlations with real life; and 3) Correlating laboratory aerospace materials flammability data with data in spacecraft environments.

Hirsch, David B.↗