Search NASA⌕ Search

SEARCH · Search NASA

Results for “deionized water”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Relating Hydro–Mechanical and Elastodynamic Properties of Dynamically Stressed Tensile–Fractured Rock in Relation to Applied Normal Stress, Fracture Aperture, and Contact Area

We exploit nonlinear elastodynamic properties of fractured rock to probe the micro-scale mechanics of fractures and understand the relation between fluid transport and fracture aperture under dynamic stressing. Experiments were conducted on rough, tensile-fractured Westerly granite subject to triaxial stresses. We measure fracture permeability for steady-state fluid flow with deionized water. Pore pressure oscillations are applied at amplitudes ranging from 0.2 to 1 MPa at 1 Hz frequency. During dynamic stressing we transmit ultrasonic signals through the fracture using an array of piezoelectric transducers (PZTs) to monitor evolution of interface properties. We examine the influence of fracture aperture and contact area by conducting measurements at effective normal stresses of 10–20 MPa. Additionally, the evolution of contact area with stress is characterized using pressure sensitive film. These experiments are conducted separately with the same fracture and map contact area at stresses from 9 to 21 MPa. The measurements are a proxy for “true” contact area for the fracture surface and we relate them to elastic properties using the calculated PZT sensor footprints via numerical modeling of Fresnel zones. We compare the elastodynamic response of the fracture using the stress-induced changes in ultrasonic wave velocities for transmitter-receiver pairs to image spatial variations in contact properties. We show that nonlinear elasticity and permeability enhancement decrease with increasing normal stress. Additionally, post-oscillation wave velocity and permeability exhibit quick recoveries toward pre-oscillation values. Estimates of fracture contact area (global and local) demonstrate that the elastodynamic and permeability responses are dominated by fracture topology.

58 GEOSCIENCES↗
DOE OSTI2026

Toward the performance assessment of advanced nuclear waste forms: temperature dependence of lanthanide borosilicate glass dissolution

Lanthanide borosilicate (LaBS) glasses are among the most promising waste forms for the immobilization of high-level radioactive waste generated from advanced nuclear fuel cycles. However, the temperature dependence of their dissolution kinetics remains poorly understood and constrained, limiting the integration of these materials into established performance assessment models. Here, we investigate the dissolution behavior of the legacy AmCm2-19 LaBS glass and the benchmark alkali aluminoborosilicate ISG-1 in deionized water between 50 °C and 250 °C using ASTM C1285 (Product Consistency Test-B) protocols. For AmCm2-19 LaBS glass, normalized elemental release rates for boron and silicon increase with temperature before plateauing near 150 °C, consistent with solubility-limited behavior. From data obtained at 50 °C and 100 °C, Arrhenius analysis yields activation energies of E a (B) = 24.8 ± 0.3 kJ mol⁻¹ and E a (Si) = 14.4 ± 0.2 kJ mol⁻¹, similar or slightly lower than those previously reported for two other compositions of LaBS glasses. No secondary phases or alteration layers were detected by SEM-EDX or pXRD. These results establish one of the first temperature-dependent kinetic datasets for LaBS glass dissolution, providing quantitative parameters to inform mechanistic corrosion models and predictive simulations of glass degradation in geological disposal environments.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Quantitative encapsulation and retention of 227 Th and decay daughters in core–shell lanthanum phosphate nanoparticles

Targeted alpha therapy (TAT) offers great promise for treating recalcitrant tumors and micrometastatic cancers. One drawback of TAT is the potential damage to normal tissues and organs due to the relocation of decay daughters from the treatment site. As such, the present study evaluates La( 227 Th)PO 4 core (C) and core +2 shells (C2S) nanoparticles (NPs) as a delivery platform of 227 Th to minimize systemic distribution of decay daughters, 223 Ra and 211 Pb. In vitro retention of decay daughters within La( 227 Th)PO 4 C NPs was influenced by the concentration of reagents used during synthesis, in which the leakage of 223 Ra was between 0.4 ± 0.2% and 20.3 ± 1.1% in deionized water. Deposition of two nonradioactive LaPO 4 shells onto La( 227 Th)PO 4 C NPs increased the retention of decay daughters to >99.75%. The toxicity of the nonradioactive LaPO 4 C and C2S NP delivery platforms was examined in a mammalian breast cancer cell line, BT-474. No significant decrease in cell viability was observed for a monolayer of BT-474 cells for NP concentrations below 233.9 μg mL –1 , however cell viability decreased below 60% when BT-474 spheroids were incubated with either LaPO 4 C or C2S NPs at concentrations exceeding 29.2 μg mL –1 . La( 227 Th)PO 4 C2S NPs exhibit a high encapsulation and in vitro retention of radionuclides with limited contribution to cellular cytotoxicity for TAT applications.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2023

Optimizing dicyandiamide pretreatment conditions for enhanced structure and electronic properties of polymeric graphitic carbon nitride

Graphitic carbon nitride, a polymeric semiconductor, possesses a distinctive electronic band structure and exceptional chemical stability, making it a highly promising material for various catalytic applications such as electrocatalysis, photocatalysis, and photo-electrocatalysis. However, its practical applications remain limited due to its low active site density and poor electrical conductivity. In this study, to overcome such limitations, we have conducted a thorough investigation to explore the impact of dicyandiamide (DCDA) precursor pretreatment prior to thermal polymerization to graphitic carbon nitride. The DCDA precursor was subjected to various pretreatment methods including grinding using mortar and pestle, recrystallization through stirring or probe sonication after dissolving in deionized water, and freeze drying, prior to thermal polymerization at 550 °C for 2 hours. The structural and morphological properties of the catalysts prepared were compared and characterized by X-ray diffraction (XRD), attenuated total reflectance–Fourier transform infrared (ATR-IR) spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) analysis while the electronic band gap properties were determined based on density functional theory (DFT) calculations for a set of crystalline systems having C/N ratios similar to those identified experimentally. In comparison to direct thermal polymerization, pretreated samples rendered the same product yield, diverse morphologies with flat or wrinkle structures, and reduced electrochemical resistance, making them suitable for use in various catalytic processes.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Semi-Dynamic Leach Testing of Densified Silicon-based Iodine Waste Forms

Iodine waste forms (IWF) require a conceptual corrosion release model (CCRM) to provide iodine (I) release rates for performance modeling nuclear waste disposal repositories. To develop a CCRM, an understanding of the corrosion mechanisms of the IWF are required along with data from consistent test methods to parameterize the model. The present study has advanced both areas by providing and assessing the corrosion resistance of IWF types based on their processing history in minor variations of semi-dynamic leach tests. The test included a series of semi-dynamic leach tests using monolithic IWFs in deionized water (leachant). Several experiments were conducted under alternate test conditions with changes to temperature, leachant replacement, leachant pH, leachant volume, masking, and surface finish to elucidate if varying these conditions impacted IWF corrosion behavior. Tests were conducted on two classes of IWFs: (1) I-bearing silver-mordenite (AgZ) materials processed by hot isostatic pressing (HIP) at different temperatures, pressures, sizes, and times; and (2) I-bearing silver-functionalized silica aerogels (SFA) processed by either HIP or spark plasma sintering (SPS). The corrosion susceptibility of AgZ samples was influenced by HIP temperature and pressure. The SPS SFAs retained I far better than HIP SFAs. Additional findings in this study include: (1) The iodine dissolution rate decreased with decreasing temperature, (2) a common ion effect may occur and slow dissolution of the host phase if the leachant is not regularly replaced, (3) pH controls the dissolution rate, and (4) the iodine dissolution rate slows with extended test time (up to 224 days). Based on this work, these parameters should thus be represented when developing a CCRM.

corrosion↗
DOE OSTI2024

Design of a high-temperature cell for cobalt-60 irradiations of aqueous solutions with in situ UV–visible spectroscopy

To understand the speciation of solutes in aqueous solutions in high temperature radiation environments, we report the design and fabrication of a custom-built, high temperature (≤300 °C) titanium irradiation cell with in situ optical spectroscopy capabilities, as afforded by coupled fiber optic cables. The wetted surfaces of the 8-inch tall cylindrical cell with 3.5 in. diameter are entirely made of titanium, sapphire, and gold, which are chemically and radiolytically inert. The initial benchmarking results are reported, including the baseline spectrum of deionized water as a function of temperature, the stability of a spectrum over 4 h at 100 °C, and an irradiated Fricke dosimetry solution under ambient irradiator temperature conditions (27.0 ± 0.5 °C). Further, the average gamma radiation dose rate in the cell in its current configuration is 26.1 ± 1.3 Gy min -1 . This cell has application in studying several processes throughout the nuclear fuel cycle, including the reactor coolant behavior.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2023

Electrical breakdown dynamics in an argon bubble submerged in conductive liquid for nanosecond pulsed discharges

Abstract This study delves into the dynamics of cold atmospheric plasma and their interaction within conductive solutions under the unique conditions of nanosecond pulsed discharges (22 kV peak voltage, 10 ns FWHM, 4.5 kV ns −1 rate-of-rise). The research focuses on the electrical response, breakdown, and discharge propagation in an argon bubble, submerged in a NaCl solution of varying conductivity. Full or partial discharges were observed at conductivities of 1.5 µ S cm −1 (deionized water) to 1.6 mS cm −1 , but no breakdown was observed at 11.0 mS cm −1 when reducing the electrode gap. It is demonstrated that at higher conductivity electric breakdown is observed only when the gas bubble comes into direct contact with the electrode and multiple emission nodes were observed at different timescales. These nodes expanded in the central region of the bubble over timescales longer than the initial high-voltage pulse. This work offers a temporal resolution of 2 ns exposure times over the first 30 ns of the initial voltage pulse, and insight into plasma formation over decaying reflected voltage oscillations over 200 ns.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Pool Boiling Reliability Tests and Degradation Mechanisms of Microporous Copper Inverse Opal (CuIOs) Structures

The rising power density in electronic systems requires thermal management solutions that are both high-performing and reliable. Porous materials such as Copper Inverse Opal (CuIOs) have unique structural features, including high permeability and high thermal conductivity, to enhance pool boiling performance. However, there is little understanding of the degradation mechanism of such porous materials under pool boiling conditions. In this study, samples of 10 ..mu..m thick CuIOs with 4.8 ..mu..m diameter, covering silicon substrate of area 11 mm x 11 mm, with various heated areas ranging from 2.5 mm x 2.5 mm to 10 mm x 10 mm, were tested in 100 degrees C deionized water at a constant heat flux of 110 Wcm -2 for 3-to-7 days. The combined effect of erosion and corrosion caused structural degradation of the CuIOs. The directly heated area had the most severe degradation while the edge of the heater and the unheated area showed progressively less degradation, maintaining some CuIOs structure even after the 7-day reliability test. Among all the tested samples with various heater sizes, the 2.5 mm x 2.5 mm heater sample - in which the heater size was designed to be comparable to the water bubble characteristic length - had the largest critical heat flux (CHF) up to 300 Wcm -2 with a superheat ~ 13 degrees C. Additionally, CuIOs with a smaller heated area performed better in terms of reliability. This study offers preliminary insights into CuIOs degradation mechanisms, contributing to the development of more robust thermal management solutions. We expect that electroless plating of CuIOs with gold (Au), nickel (Ni), and atomic layer deposition (ALD) aluminum oxide (Al 2 O 3 ) in combination with appropriate application-specific coolants will further improve the reliability and lifetime of the CuIOs.

boiling-induced degradation↗
DOE OSTI2024

Intelligent Electrochemical Sensors for Precise Identification of Volatile Organic Compounds Enabled by Neural Network Analysis

The volatile organic compounds (VOCs) in a wide spectrum of categories were identified as biomarkers in aquatic environments, playing an important role in marine and freshwater ecology and global atmospheric chemistry. VOCs released from biofuel have also attracted increasing attention. Although the importance has been recognized, the portable detection and analysis methods of VOC in aquatic systems have not yet been well developed and understood. Here, in this work, we innovatively proposed an intelligent electrochemical sensing approach to classify and quantify VOCs in solution. Utilizing the cyclic voltammetry (CV) method with an ionic liquid (IL)-based electrolyte, we analyzed 50 μL samples of various VOC analytes, including acetic acid (AC), acetone, dimethylformamide (DMF), dimethyl sulfoxide (DMSO), ethanol, formaldehyde, formic acid, methanol, methyl formate (MF), toluene, and a formaldehyde-methanol mixture, along with deionized water (DI water). The generated voltammograms were subsequently analyzed using our uniquely designed and optimized 1-D convolutional neural network (1D-CNN). This deep-learning algorithm achieved a 99.09% accuracy in VOC classification validated through fivefold cross-validation and demonstrated an impressive 94.4% test accuracy for methanol detection within a 10 μL error range. For quantification, the system accurately categorized methanol volumes ranging from 0 to 50 μL in 10 μL increments, achieving a 98.18% accuracy. A notable linear correlation (R2 = 95.56%) was found between max current density at the oxidation peak and methanol volume, with the limit of detection (LOD) at 9.3 μL. Such a sensing method exhibits potential for portability, high accuracy, and generalization in the classification and quantification, ultimately reshaping the realm of VOC analysis in solution.

42 ENGINEERING↗
DOE OSTI2020

Doping of CdTe Using CuCl2 Solution for Highly Efficient Photovoltaic Devices

Here, we report doping of cadmium telluride (CdTe) thin film solar cells using copper (II) chloride (CuCl 2 ) solution in deionized water. The CdTe thin films were immersed in 0.1 mmol CuCl 2 solution in water and annealed in the temperature range of 180-240 degrees C for various time durations. The devices were completed using thermally evaporated gold (Au) and measured under simulated AM1.5G spectrum. The average device efficiency of CuCl 2 treated CdTe devices increased to 13.7 % (best cell reaching 14.0%) with significant improvement on open-circuit voltage (VOC ) as compared with 12.4% (best cell 12.7%) for thermally evaporated Cu doped CdTe devices. For CuCl 2 treated CdTe devices, we found higher photoluminescence (PL) intensity and longer carrier life time at room temperature indicating solution based doping offers better control of Cu doping density as compared with evaporated Cu.

14 SOLAR ENERGY↗
DOE OSTI2021

Effects of Al:Si and (Al+Na):Si ratios on the static corrosion of sodium‐boroaluminosilicate glasses

Abstract Understanding alteration mechanisms of borosilicate glasses in aqueous media is essential to nuclear waste performance assessments to ensure radioisotopes are contained for extended durations. Aluminum is typically added to glass compositions to reduce the extent of alteration. However, previous work on 7‐day durability tests has suggested that Al has a nonlinear relationship with extent of alteration. The effects of Al:Si and (Al+Na):Si substitutions on glass durability were evaluated using series of glasses based on the International Simple Glass corroded in static conditions up to 13 months in deionized water at 90°C. The alteration behavior was determined by measurement of element release in solution. The ⁓7‐day alteration trends across the series were consistent with predicted trends. The 13‐month results indicated overall alteration decreased as Al:Si ratios increased and was unaffected by changes in (Al+Na):Si except for the glass with the highest (Al+Na):Si ratio (ISG‐A23N), which completely altered within 14 days. Frequent sampling and in situ Raman measurements of solutions revealed ISG‐A23N experienced several distinguishable alteration rate regimes within 7 days, forming a ⁓100 µm alteration layer and a NaSiAlO 4 zeolite.

Reiser, Joelle T.↗
DOE OSTI2022

Radiation effects on the structure and alteration behavior of an SiO 2 –Al 2 O 3 –B 2 O 3 –Na 2 O glass

As borosilicate glasses are used in many countries to immobilize fission products and minor actinides after spent fuel reprocessing before storage in a deep geological repository, assessing that their chemical durability is of paramount importance. Here, pristine and preirradiated (952 MeV, 136Xe) SiO 2 –B2O 3 –Al2O 3 –Na 2 O glasses with the same molar ratios as in the French SON68 and ISG glasses have been subjected to aqueous corrosion in deionized water and in silica-saturated solution to measure the initial and longer term alteration rates. Pristine and preirradiated glasses corrode following the same mechanisms, but the preirradiation has a strong impact on the initial dissolution rate (increase by a factor of 5.6), and on the alteration layer depth in silica-saturated conditions (by two- to threefolds). The later result is related to the formation of a more porous, less passivating gel on the preirradiated glass specimen. Using both experimental spectroscopies (NMR, IR, and SFG) and classical molecular dynamics, the radiation effects on the glass structure and water diffusion have been assessed. After preirradiation, the density and the polymerization degree of the glass decrease, whereas the topological disorder increases. In consequence, water diffusion accelerates. These observations allow to correlate the radiation impact on the alteration behavior to the structural changes.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Seeded Stage III glass dissolution behavior of a statistically designed glass matrix

The glass dissolution rate of some glasses accelerates after prolonged time spent at a slow, residual glass dissolution rate. This phenomenon is referred to as Stage III behavior. Here, the acceleration in glass dissolution rate linked to Stage III behavior is significant and may be the most impactful to long-term performance of glass in a repository. This work is aimed at understanding the effect of glass composition on Stage III behavior to add a level of technical defensibility to glass disposal. To this end, a set of twenty-four glass compositions were statistically designed, where eight glass components (SiO 2 , B 2 O 3 , Al 2 O 3 , CaO, Na 2 O, SnO 2 , ZrO 2 , and Others) have been independently varied in order to study the individual effects of each. These glasses have been subjected to static dissolution tests at 90 °C in deionized water and then seeded with zeolite Na-P2 28 days into the testing to induce Stage III behavior. The response of the glasses to the zeolite seeds fell into four primary types: 1) no response to seeds; 2) an immediate linear sustained acceleration in the rate; 3) an immediate linear acceleration in the rate followed by a decrease; and, 4) a progressive acceleration in the rate that is concurrent with the addition of the seeds. The main glass components observed to influence these behaviors were CaO, Al 2 O 3 , B 2 O 3 , and ZrO 2 , where: 1) CaO influenced which glasses showed a Stage III response to seeds (high CaO: Types 2, 3, and 4) or did not respond to seeds (low CaO: Type 1), 2) Al 2 O 3 and B 2 O 3 influenced which glasses showed a sustainable Stage III response (high Al 2 O 3 : Types 2 and 4) versus transitory response (low Al 2 O 3 and high B 2 O 3 : Type 3), and 3) ZrO 2 concentration influenced whether glasses showed a linear (high ZrO 2 : Type 2) versus progressive (low ZrO 2 : Type 4) response to seeds.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fracture Sustainability in Enhanced Geothermal Systems: Experimental and Modeling Constraints

Enhanced geothermal systems (EGS) offer the potential for a much larger energy source than conventional hydrothermal systems. Hot, low-permeability rocks are prevalent at depth around the world, but the challenge of extracting thermal energy depends on the ability to create and sustain open fracture networks. Laboratory experiments were conducted using a suite of selected rock cores (granite, metasediment, rhyolite ash-flow tuff, and silicified rhyolitic tuff) at relevant pressures (uniaxial loading up to 20.7 MPa and fluid pressures up to 10.3 MPa) and temperatures (150–250 °C) to evaluate the potential impacts of circulating fluids through fractured rock by monitoring changes in fracture aperture, mineralogy, permeability, and fluid chemistry. Because a fluid in disequilibrium with the rocks (deionized water) was used for these experiments, there was net dissolution of the rock sample: this increased with increasing temperature and experiment duration. Thermal-hydrological-mechanical-chemical (THMC) modeling simulations were performed for the rhyolite ash-flow tuff experiment to test the ability to predict the observed changes. These simulations were performed in two steps: a thermal-hydrological-mechanical (THM) simulation to evaluate the effects of compression of the fracture, and a thermal-hydrological-chemical (THC) simulation to evaluate the effects of hydrothermal reactions on the fracture mineralogy, porosity, and permeability. Furthermore, these experiments and simulations point out how differences in rock mineralogy, fluid chemistry, and geomechanical properties influence how long asperity-propped fracture apertures may be sustained. Such core-scale experiments and simulations can be used to predict EGS reservoir behavior on the field scale.

15 GEOTHERMAL ENERGY↗
DOE OSTI2020

The Effects of Synthesis Conditions on the Carbon Capture Capacity of Polyethylenimine Impregnated Protonated Titanate Nanotubes

Capture and storage of carbon dioxide emitted from power plants, which burn fossil fuels, is one of the best ways to mitigate climate change. Polyethylenimine (PEI) impregnated protonated titanate nanotubes (PEI-PTNTs) are efficient amine-modified solid adsorbents for post combustion carbon capture. This study is to investigate the effects of synthesis conditions of titanate nanotubes on the carbon capture capacity of PEI-PTNTs. PTNTs are synthesized using hydrothermal treatment of TiO 2 anatase powder at different temperatures and in different days, followed by washing with dilute HCl solution and deionized water. PEI-PTNTs are prepared by loading PEI (M.W. = 10,000) onto PTNTs at a weight ratio of 1:1 using a wet impregnation process. PTNTs and PEI-PTNTs are characterized using transmission electron microscopy, porosity and surface area analysis, powder X-ray diffraction, and Fourier transform infrared spectroscopy. CO 2 adsorption is conducted at 75 °C using simulated flue gas, and CO 2 desorption is performed at 110 °C by purging the adsorbent with dry nitrogen gas. CO 2 adsorption experiments demonstrate that the PEI-PTNTs synthesized at 130 °C within 3 or 5 days, have the highest CO 2 capture capacity. These optimized PEI-PTNTs have a significant potential to capture CO 2 from power plants.

Materials Science↗
DOE OSTI2020

Sapphire advanced mitigation process: wet etch to expose sub-surface damage and increase laser damage resistance and mechanical strength

In this study, a novel, to the best of our knowledge, method of wet chemical etching of sapphire workpieces (such as optics, wafers, windows, and cones), called the sapphire advanced mitigation process (or sapphire AMP), has been developed that exposes sub-surface mechanical damage created during the optical fabrication process and significantly enhances the surface laser damage resistance (> 2×) and mechanical strength (up to ~ 2.6×). Sapphire AMP involves first treating the workpiece with a mixture of sulfuric and phosphoric acid ([H 2 SO 4 ]:[H 3 PO 4 ]= 1 : 3) at 220°C, followed with phosphoric acid at 160°C, then with sodium hydroxide base (NaOH) and surfactant at 40°C, and finally with a high-pressure deionized water spray rinse. Sapphire AMP has been demonstrated on both A- and C-plane sapphire workpieces. The mechanism of this etch process involves the reaction of the sapphire (Al 2 O 3 ) surface with sulfuric acid (H 2 SO 4 ) forming aluminum sulfate [Al2(SO4)3], which has low solubility. The high phosphoric acid content in the first and second steps of sapphire AMP results in the efficient conversion of Al 2 (SO 4 ) 3 to aluminum phosphate (AlPO 4 ), which is very soluble, greatly reducing reaction product redeposition on the workpiece surface. Sapphire AMP is shown to expose sub-surface mechanical damage on the sapphire surface created during the grinding and polishing processes, whose etched morphology has either isotropic or anisotropic evolution depending on the nature of the initial surface damage. Sapphire AMP was also designed to remove the key known surface, laser absorbing precursors (namely, foreign chemical impurities, the fracture surface layer of preexisting sub-surface damage, and reaction product or foreign species redeposition or precipitation). Static and sliding indention induced surface microfractures on sapphire are shown after sapphire AMP to have a significant decrease in the fast photoluminescence intensity (a known metric for measuring the degree of laser damaging absorbing precursors). In addition, the onset of laser damage (at 351 nm 3 ns) on sapphire AMP treated workpieces was shown to increase in fluence from ~ 4 to >9.5J/cm 2 . Finally, biaxial ball-on-ring mechanical tests on sapphire disks showed an increase in the failure stress from 340 MPa (with pre-existing 28 µm flaws) to ~ 900MPa after sapphire AMP, which is attributed to the blunting of the surface microfractures.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Utah FORGE: Slide-Hold-Slide Experiments on Westerly Granite at Temperatures up to 250 Degrees C

Laboratory slide-hold-slide tests were conducted in a conventional triaxial deformation configuration on 1-inch diameter cylindrical cores of Westerly granite bisected by a sawcut oriented at 30 degrees from vertical. Tests were conducted at a constant confining pressure of 30 MPa with a 10 MPa pore fluid pressure. The pore fluid was deionized water. Experiments were conducted at temperatures of 22, 100, 200, and 250 C. This data was collected to examine fault strength recovery in hydrothermal conditions.

15 GEOTHERMAL ENERGY↗
DOE OSTI2020

Encapsulation and retention of 225 Ac, 223 Ra, 227 Th, and decay daughters in zircon-type gadolinium vanadate nanoparticles

Abstract Unwanted targeting of healthy organs caused by the relocation of radionuclides from the target site has been one of the limiting factors in the widespread application of targeted alpha therapy in patient regimens. GdVO 4 nanoparticles (NPs) were developed as platforms to encapsulate α -emitting radionuclides 223 Ra, 225 Ac, and 227 Th, and retain their decay daughters at the target site. Polycrystalline GdVO 4 NPs with different morphologies and a zircon-type tetragonal crystal structure were obtained by precipitation of GdCl 3 and Na 3 VO 4 in aqueous media at room temperature. The ability of GdVO 4 crystals to host multivalent ions was initially assessed using La, Cs, Bi, Ba, and Pb as surrogates of the radionuclides under investigation. A decrease in Ba encapsulation was obtained after increasing the concentration of surrogate ions, whereas the encapsulation of La cations in GdVO 4 NPs was quantitative (∼100%). Retention of radionuclides was assessed in vitro by dialyzing the radioactive GdVO 4 NPs against deionized water. While 227 Th was quantitatively encapsulated (100%), a partial encapsulation of 223 Ra (∼75%) and 225 Ac (>60%) was observed in GdVO 4 NPs. The maximum leakage of 221 Fr (1st decay daughter of 225 Ac) was 55.4 ± 3.6%, whereas for 223 Ra (1st decay daughter of 227 Th) the maximum leakage was 73.0 ± 4.0%. These results show the potential of GdVO 4 NPs as platforms of α -emitting radionuclides for their application in targeted alpha therapy.

62 RADIOLOGY AND NUCLEAR MEDICINE↗