Search NASA⌕ Search

SEARCH · Search NASA

Results for “lamellar”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Elevated temperature creep-rupture behavior of the single crystal nickel-base superalloy NASAIR 100

The creep and rupture behavior of 001-line-oriented single crystals of the nickel-base superalloy NASAIR 100 was investigated at temperatures of 925 and 1000 C. In the stress and temperature ranges studied, the steady state creep rate, time to failure, time to the onset of secondary creep, and the time to the onset of tertiary creep all exhibited power law dependencies on the applied stress. The creep rate exponents for this alloy were between seven and eight, and the modulus-corrected activation energy for creep was approximately 350 kjoule/mole, which was comparable to the measured activation energy for Ostwald ripening of the gamma-prime precipitates. Oriented gamma-prime coarsening to form lamellae perpendicular to the applied stress was very prominent during creep. At 1000 C, the formation of a continuous gamma-gamma-prime lamellar structure was completed during the primary creep stage. Shear through the gamma-gamma-prime interface is considerd to be the rate limiting step in the deformation process. Gradual thickening of the lamellae appeared to be the cause of the onset of tertiary creep. At 925 C, the fully developed lamellar structure was not achieved until the secondary or tertiary creep stages. At this temperature, the gamma-gamma-prime lamellar structure did not appear to be as beneficial for creep resistance as at the higher temperature.

Nathal, M. V.↗
NASA NTRS1992

Influence of convection on microstructure

The primary motivation for this research has been to determine the cause for space processing altering the microstructure of some eutectics, especially the MnBi-Bi eutectic. Prior experimental research at Grumman and here showed that the microstructure of MnBi-Bi eutectic is twice as fine when solidified in space or in a magnetic field, is uninfluenced by interfacial temperature gradient, adjusts very quickly to changes in freezing rate, and becomes coarser when spin-up/spin-down (accelerated crucible rotation technique) is used during solidification. Theoretical work at Clarkson predicted that buoyancy driven convection on earth could not account for the two fold change in fiber spacing caused by solidification in space. However, a lamellar structure with a planar interface was assumed, and the Soret effect was not included in the analysis. Experimental work at Clarkson showed that the interface is not planar, and that MnBi fibers project out in front of the Bi matrix on the order of one fiber diameter. Originally four primary hypotheses were to be tested under this current grant: (1) a fibrous microstructure is much more sensitive to convection than a lamellar microstructure, which was assumed in our prior theoretical treatment; (2) an interface with one phase projecting out into the melt is much more sensitive to convection than a planar interface, which was assumed in our prior theoretical treatment; (3) the Soret effect is much more important in the absence of convection and has a sufficiently large influence on microstructure that its action can explain the flight results; and (4) the microstructure is much more sensitive to convection when the composition of the bulk melt is off eutectic. As reported previously, we have learned that while a fibrous microstructure and a non-planar interface are more sensitive to convection than a lamellar microstructure with a planar interface, the influence of convection remains too small to explain the flight and magnetic field results. Similarly addition of the Soret effect does not explain the flight and magnetic field results.

Wilcox, William R.↗
NASA NTRS1999

Effects of Melt Processing on Evolution of Structure in PEEK

We report on the effects of melt processing temperature on structure formation in Poly(ether-ether-ketone), PEEK. Real time Small Angle X-ray Scattering, SAXS, and thermal analysis are used to follow the melting behavior after various stages of processing. Assignment of peaks to structural entities within the material, the relative perfection of the crystals, and the possibility of their reorganization, are all influenced by the melt processing history. With the advent of high intensity synchrotron sources of X-radiation, polymer scientists gain a research tool which, when used along with thermal analysis, provides additional structural information about the crystals during growth and subsequent melting. PEEK is an engineering thermoplastic polymer with a very high glass transition temperature (145 C) and crystal melting point (337 C). PEEK has been the subject of recent studies by X-ray scattering in which melt and cold crystallization were followed in real-time. X-ray scattering and thermal studies have been used to address the formation of dual endothermic response which has been variously ascribed to lamellar insertion, dual crystal populations, or melting followed by re-crystallization. Another important issue is whether all of the amorphous phase is located in interlamellar regions, or alternatively whether some is located in "pockets" away from the crystalline lamellar stacks. The interpretation of scattering from lamellar stacks varies depending upon whether such amorphous pockets are formed. Some groups believe all of the amorphous phase is interlamellar. This leads to selection of a smaller thickness for the crystals. Other groups suggest that most amorphous phase is not interlamellar, and this leads to the suggestion that the crystal thickness is larger than the amorphous layer within the stacks. To investigate these ideas, we used SAXS and Differential Scanning Calorimetry to compare results of single and dual stage melt crystallization of PEEK using a treatment scheme involving annealing/crystallization at T(sub a1) followed by annealing at T(sub a2) where either T(sub a1) < T(sub a2) or T(sub a1) > T(sub a2). We proposed a model to explain multiple melting endotherms in PPS, treated according to one or two-stage melt or cold crystallization. Key features of this model are that multiple endotherms: (1) are due to reorganization/recrystallization after cold crystallization; and, (2) are dominated by crystal morphology after melt crystallization at high T. In other words, multiple distinct crystal populations are formed by the latter treatment, leading to observation of multiple melting. PEEK 45OG pellets (ICI Americas) were the starting material for this study. Films were compression molded at 400 C, then quenched to ice water. Samples were heated to 375 C in a Mettler FP80 hot stage and held for three min. to erase crystal seeds before cooling them to T(sub a1) = 280 C . Samples were held at T(sub a2) for a period of time, then immediately heated to 360 C. In the second treatment samples were held at T(sub a1) = 31 C for different crystallization times t(sub c) then cooled to 295 C and held 15 min. In situ (SAXS) experiments were performed at the Brookhaven National Synchrotron Light Source with the sample located inside the Mettler hot stage. The system was equipped with a two-dimensional position sensitive detector. The sample to detector distance was 172.7 cm and the X-ray wavelength was 1.54 Angstroms. SAXS data were taken continuously during the isothermal periods and during the heating to 360 C at 5 C/min. Each SAXS scan was collected for 30 sec. Since the samples were isotropic, circular integration was used to increase the signal to noise ratio. After dual stage melt crystallization with T(sub a1) < T(sub a2) the lower melting endotherm arises from holding at T(sub a1). During cooling a broad distribution of crystals forms, and the low-melting tail is perfected during T(sub al). Heating to T(sub a2) melts these imperfect crystals and allows others with greater average long spacing to form in their place. After dual stage crystallization with T(sub a1) > T(sub a2), the amount of space remaining for additional growth at T(sub a2) depends upon the holding time at T(sub a1). The long period of crystals formed at T(sub a2) is smaller than that formed at T(sub a1) due to growth in a now-restricted geometry. Perfection of crystals is seen as an increase of the intensity of the population scattering at higher s, while the intensity of the population scattering at lower s stays constant. During heating from below to above the minor endotherm, we see rapid decrease of the intensity of the X-ray scattering corresponding to the population of crystals scattering in the shoulder. Another important observation is that after the sample is annealed at 295 C, the shoulder intensity is restored once again. The population scattering at higher s remains longer before it disappears in the sample treated to the second stage of melt crystallization, compared to the sample crystallized with a single stage. This could be interpreted as an effect of continued perfection of the less perfect population, which is also reflected in the increased melting temperature of the smaller endotherm as the holding time at 295 C increases. In the corresponding DSC scans we see a shift in the area and the peak temperature of the lower melting endotherm with an increase of the annealing time.

Georgiev, Georgi↗
NASA NTRS2003

Microstructure and Mechanical Properties of Extruded Gamma Met PX

A gamma TiAl alloy with a high Nb content is being assessed as a compressor blade material. The microstructure and mechanical properties of extruded Ti-45Al-X(Nb,B,C) (at %) were evaluated in both an as-extruded condition and after a lamellar heat treatment. Tensile behavior of both as-extruded and lamellar heat treated specimens was studied in the temperature range of RT to 926 C. In general, the yield stress and ultimate tensile strength reached relatively high values at room temperature and decreased with increasing deformation temperature. The fatigue strength of both microstructures was characterized at 650 C and compared to a baseline TiAl alloy and to a Ni-base superalloy. Tensile and fatigue specimens were also exposed to 800 C for 200 h in air to evaluate the alloy's environmental resistance. A decrease in ductility was observed at room temperature due to the 800 C exposure but the 650 C fatigue properties were unaffected. Compressive and tensile creep testing between 727 and 1027 C revealed that the creep deformation was reproducible and predictable. Creep strengths reached superalloy-like levels at fast strain rates and lower temperatures but deformation at slower strain rates and/or higher temperature indicated significant weakening for the as-extruded condition. At high temperatures and low stresses, the lamellar microstructure had improved creep properties when compared to the as-extruded material. Microstructural evolution during heat treatment, identification of various phases, and the effect of microstructure on the tensile, fatigue, and creep behaviors is discussed.

Draper, S. L.↗
NASA NTRS2003

Microstructure and Mechanical Properties of Extruded Gamma Microstructure Met PX

A gamma TiAl alloy with a high Nb content is being assessed as a compressor blade material. The microstructure and mechanical properties of extruded Ti-45Al-X(Nb,B,C) (at.%) were evaluated in both an as-extruded condition and after a lamellar heat treatment. Tensile behavior of both as-extruded and lamellar heat treated specimens was studied in the temperature range of RT to 926 C. In general, the yield stress and ultimate tensile strength reached relatively high values at room temperature and decreased with increasing deformation temperature. The fatigue strength of both microstructures was characterized at 650 C and compared to a baseline TiAl alloy and to a Ni-base superalloy. Tensile and fatigue specimens were also exposed to 800 C for 200 h in air to evaluate the alloy's environmental resistance. A decrease in ductility was observed at room temperature due to the 800 C. exposure but the 650 C fatigue properties were unaffected. Compressive and tensile creep testing between 727 and 1027 C revealed that the creep deformation was reproducible and predictable. Creep strengths reached superalloy-like levels at fast strain rates and lower temperatures but deformation at slower strain rates and/or higher temperature indicated significant weakening for the as-extruded condition. At high temperatures and low stresses, the lamellar microstructure had improved creep properties when compared to the as-extruded material. Microstructural evolution during heat treatment, identification of various phases, and the effect of microstructure on the tensile, fatigue, and creep behaviors is discussed.

Draper, S. L.↗
NASA NTRS2003

Aging of microstructural compartments in human compact bone

Composition of microstructural compartments in compact bone of aging male subjects was assessed using Raman microscopy. Secondary mineralization of unremodeled fragments persisted for two decades. Replacement of these tissue fragments with secondary osteons kept mean composition constant over age, but at a fully mineralized limit. Slowing of remodeling may increase fracture susceptibility through an increase in proportion of highly mineralized tissue. In this study, the aging process in the microstructural compartments of human femoral cortical bone was investigated and related to changes in the overall tissue composition within the age range of 17-73 years. Raman microprobe analysis was used to assess the mineral content, mineral crystallinity, and carbonate substitution in fragments of primary lamellar bone that survived remodeling for decades. Tissue composition of the secondary osteonal population was investigated to determine the composition of turned over tissue volume. Finally, Raman spectral analysis of homogenized tissue was performed to evaluate the effects of unremodeled and newly formed tissue on the overall tissue composition. The chemical composition of the primary lamellar bone exhibited two chronological stages. Organic matrix became more mineralized and the crystallinity of the mineral improved during the first stage, which lasted for two decades. The mineral content and the mineral crystallinity did not vary during the second stage. The results for the primary lamellar bone demonstrated that physiological mineralization, as evidenced by crystal growth and maturation, is a continuous process that may persist as long as two decades, and the growth and maturation process stops after the organic matrix becomes "fully mineralized." The average mineral content and the average mineral crystallinity of the homogenized tissue did not change with age. It was also observed that the mineral content of the homogenized tissue was consistently greater than the osteons and similar to the "fully mineralized" stage of primary bone. The results of this study demonstrated that unremodeled compartments of bone grow older through maturation and growth of mineral crystals in a protracted fashion. However, the secondary osteonal remodeling impedes this aging process and maintains the mean tissue age fairly constant over decades. Therefore, slowing of remodeling may lead to brittle bone tissue through accumulation of fully mineralized tissue fragments.

Non-NASA Center↗
DOE OSTI2026

Electrostatically driven pattern formation in mixed charged–neutral multicomponent elastic membranes

Multicomponent crystalline and amorphous elastic shells exhibit heterogeneous surface patterns that provide distinctive functionalities in cellular environments. Such patterning typically arises from the competition between short-range attractive and long-range repulsive interactions in membranes. Here, we demonstrate that the intrinsic competition between electrostatic repulsion and elastic deformation is sufficient to drive spontaneous surface patterning in elastic shells, requiring no additional attractive interactions. Using numerical simulations, we demonstrate pattern formation in mechanically homogeneous membranes with heterogeneous surface charge composition across different topologies, including spheres, discs, and flat periodic membranes. We also examine patterns in crystalline and amorphous shells of coassembled charged and neutral components with different bending rigidities. At low charge fraction, discrete charged surface domains form. At intermediate charge fraction, the competition between electrostatics and elasticity leads to elongated domains (rods) of the charged component, which results in lamellar patterns at nearly equal fraction of the charged and neutral components. At high charge fraction, nanodomains of the neutral component form. Amorphous shells exhibit similar progressions but with disordered structures rather than ordered lamellar patterns. These pattern morphologies are observed in both the closed shells and flat membranes. As salt concentration increases, all patterns coarsen due to the screening of electrostatic interactions.

charge heterogeneity↗
DOE OSTI2021

Implementation of a self-consistent slab model of bilayer structure in the SasView suite

Slab models are simple and useful structural descriptions which have long been used to describe lyotropic lamellar phases, such as lipid bilayers. Typically, slab models assume a midline symmetry and break a bilayer structure into three pieces, a central solvent-free core and two symmetric outer layers composed of the soluble portion of the amphiphile and associated solvent. This breakdown matches reasonably well to the distribution of neutron scattering length density and therefore is a convenient and common approach for the treatment of small-angle scattering data. Here, an implementation of this model within the SasView software suite is reported. The implementation is intended to provide physical consistency through the area per amphiphile molecule and number of solvent molecules included within the solvent-exposed outer layer. The proper use of this model requires knowledge of (or good estimates for) the amphiphile and solvent molecule volume and atomic composition, ultimately providing a self-consistent data treatment with only two free parameters: the lateral area per amphiphile molecule and the number of solvent molecules included in the outer region per amphiphile molecule. Here, the use of this code is demonstrated in the fitting of standard lipid bilayer data sets, obtaining structural parameters consistent with prior literature and illustrating the typical and ideal cases of fitting for neutron scattering data obtained using single or multiple contrast conditions. While demonstrated here for lipid bilayers, this model is intended for general application to block copolymers, surfactants, and other lyotropic lamellar phase structures for which a slab model is able to reasonably estimate the neutron scattering length density/electron-density profile of inner and outer layers of the lamellae.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Time-Resolved Structural Kinetics of an Organic Mixed Ionic–Electronic Conductor

The structure and packing of organic mixed ionic–electronic conductors have an especially significant effect on transport properties. In operating devices, this structure is not fixed but is responsive to changes in electrochemical potential, ion intercalation, and solvent swelling. Toward this end, the steady-state and transient structure of the model organic mixed conductor, poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS), is characterized using multimodal time-resolved operando techniques. Steady-state operando X-ray scattering reveals a doping-induced lamellar expansion of 1.6 Å followed by 0.4 Å relaxation at high doping levels. Time-resolved operando X-ray scattering reveals asymmetric rates of lamellar structural change during doping and dedoping that do not directly depend on potential or charging transients. Further, time-resolved spectroscopy establishes a link between structural transients and the complex kinetics of electronic charge carrier subpopulations, in particular the polaron–bipolaron equilibrium. These findings provide insight into the factors limiting the response time of organic mixed-conductor-based devices, and present the first real-time observation of the structural changes during doping and dedoping of a conjugated polymer system via X-ray scattering.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Stable Thermotropic 3D and 2D Double Gyroid Nanostructures with Sub-2-nm Feature Size from Scalable Sugar–Polyolefin Conjugates

In this study, ultra-low molecular weight disaccharide–polyolefin conjugates with cellobiose, lactose and maltose head groups and atactic polypropene tails, such as 1, undergo a series of irreversible thermotropic order–order transitions with increasing temperature to provide nanostructured phases in the sequence: lamellar (L), hexagonal perforated lamellar (HPL), double gyroid (DG) and hexagonal cylindrical (C). The DG phase displays exceptional stability at ambient temperature and features two interpenetrating sugar domain networks having a sub-2-nm strut width and a lattice parameter, a DG , of 13.1 nm. The unique stability of this DG phase extends further within ultrathin films all the way down to the two-dimensional limit of 15 nm in which film thickness, l, is now less than the surface-oriented unit cell height, h DG . In addition to raising the fundamental question of what minimally constitutes a Schoen triply periodic minimal surface and DG lattice, these results serve to establish the class of sugar–polyolefin conjugates as a new material platform for nanoscience and nanotechnology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Stable Thermotropic 3D and 2D Double Gyroid Nanostructures with Sub‐2‐nm Feature Size from Scalable Sugar–Polyolefin Conjugates

Abstract Ultra‐low molecular weight disaccharide–polyolefin conjugates with cellobiose, lactose and maltose head groups and atactic polypropene tails, such as 1 , undergo a series of irreversible thermotropic order–order transitions with increasing temperature to provide nanostructured phases in the sequence: lamellar ( L ), hexagonal perforated lamellar ( HPL ), double gyroid ( DG ) and hexagonal cylindrical ( C ). The DG phase displays exceptional stability at ambient temperature and features two interpenetrating sugar domain networks having a sub‐2‐nm strut width and a lattice parameter, a DG , of 13.1 nm. The unique stability of this DG phase extends further within ultrathin films all the way down to the two‐dimensional limit of 15 nm in which film thickness, l , is now less than the surface‐oriented unit cell height, h DG . In addition to raising the fundamental question of what minimally constitutes a Schoen triply periodic minimal surface and DG lattice, these results serve to establish the class of sugar–polyolefin conjugates as a new material platform for nanoscience and nanotechnology.

Nowak, Samantha R.↗
DOE OSTI2021

Plastic deformation mechanism of calcium-silicate hydrates determined by deviatoric-stress Raman spectroscopy

Highlights: • C-(A-)S-H samples under stress were characterized at the bond and grain level. • Small angle scattering showed that 720 MPa reduced grain thickness by 30%. • In-situ Raman showed that cross-linked C-A-S-H slips along its intralayer. • However, in-situ Raman showed that C-S-H slips along the interlayer. • In-situ Raman also showed a growth in CaCO{sub 3}, indicating fracture in both samples. Creep of the cement matrix affects the structural stability of concrete. In Portland cements, the creep is largely controlled by the binding phase calcium-(aluminum-)silicate-hydrate, or C-(A-)S-H. This phase has a lamellar structure and under deviatoric stress aligns its c-axis with the principal stress. However, the limiting resistance to this reorientation is unknown at the nanocrystalline level. Small-angle X-ray scattering shows that the lamellae thickness decreases under 100's MPa deviatoric stress. Deviatoric stress Raman spectroscopy shows that there are two ways that this break-up can occur. If the material's silicate chains are cross-linked, then strain in SiO bonds does not increase above certain stresses, indicating a relaxation adjacent to the SiO bond. If the chains are not cross-linked, then the silicate chains are broken up by rastering against each other, introducing defects. These results show that the plastic deformation of C-(A-)S-H is relevant for Portland cement creep.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Quantitative microstructural investigation of 3D-printed and cast cement pastes using micro-computed tomography and image analysis

Highlights: • Processing alters the microstructure in 3D-printed lamellar cubic element. • A unique patterned and connected pore microstructure network exists. • Micro-channels are connected through micro-pores present at interfaces regions. • Three distinct pore volume domains exists in hardened microstructure. • Volume and frequency of pore, hydrated, and unhydrated clusters are dissimilar. Microstructural phases and mechanical properties of lamellar 3D-printed and cast hardened cement paste (hcp) elements were investigated using a lab-based X-ray microscope at two levels of magnification (0.4× and 4×). K-means clustering was used for quantitative image analysis. The entire volume of intact 3-days-old 3D-printed and cast hcp elements was characterized at 0.4× magnification. Three microstructural features (macro-pores, micro-channels, and interfacial micro-pores) were found to reside in three distinct pore size domains. The largest pores of the 3D-printed element were larger than the largest pores of the reference cast hcp element. Moreover, the smallest pore sizes of the 3D-printed element were found to be smaller than those present in the cast counterparts. Micro-channels were found to be connected to one another through the micro-pores present at interfacial regions, indicating the presence of a uniquely patterned and interconnected pore network. The role of locally weak and porous interfaces on mechanical response and fracture properties is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High performance Nb/TiNi nanocomposites produced by packaged accumulative roll bonding

Taking full advantage of intrinsic high strength of nano-reinforcements has been proven difficult in a composite until the concept of strain matching was experimental verified in a nanowire Nb/TiNi in-situ composite, which was obtained via solidifying eutectic Nb/TiNi and subsequent severe wire drawing. However, the volume fraction of the nano-reinforcement was dictated by eutectic reaction, which severely limited the development of high-performance composites. Here, the martensitic transformation nanocomposites were successfully acquired with increased volume fraction and changeable morphology of the nano-reinforcement through hot packaged ARB (PARB) and subsequent wire drawing. The nano-reinforcement with lamellar configuration in the composite could exhibit a large lattice strain of similar to 3.8%, which demonstrated the applicability and effectiveness of the strain matching principle in nano-lamellar composite. The obtained composites show a yield strength over 2.0 GPa and a quasi-linear elastic strain as larger as similar to 6.5% with adjustable apparent elastic modulus from 30 to 50 GPa.

42 ENGINEERING↗
DOE OSTI2020

In-situ X-ray scattering study of isotactic polypropylene/graphene nanocomposites under shear during fused deposition modeling 3D printing

Complementary techniques were applied to characterize the structure property relationships of FDM printed isotactic polypropylene/graphene nanocomposites. Raman spectroscopy indicated that graphene was mostly exfoliated during the nozzle extrusion process. Rheological measurements of the viscosity indicated that the presence of graphene induced shear thinning during extrusion. Azimuthal scans of wide angle x-ray scattering indicate correlated thermal fluctuations of the graphene platelets which stops abruptly at the onset of transcrystallization, or templating of the iPP chains on the graphene. X-ray microbeam SAXS analysis show the formation of ‘shish-kebab’ structures at the core of the unfilled filaments, where the ‘kebab’ component vanishes at the fiber-fiber interface enabling interdiffusion. Weak lamellar structure, and a corresponding decrease in the storage modulus are observed with the addition of 5% graphene. The lamellar structure disappears entirely with the addition of 10% graphene, while the storage modulus is decreased by nearly 50%. Thermal imaging of heat flux dissipation across molded and printed samples shows no orientational effects in pure iPP despite differences in crystal structure. Thermal conductivity increases dramatically in the samples with 10% graphene, and strong orientational effects are observed where the thermal coefficients differ by 180% between samples printed parallel or perpendicular to the heat flux.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Systematic discovery of new nano-scale metastable intermetallic eutectic phases in laser rapid solidified Aluminum-Germanium alloy

Laser surface remelting of as-cast Al-Ge eutectic alloy is shown to produce ultrafine lamellar eutectic morphology with interlamellar spacing refined up to ∼60 nm and composed of FCC Al solid solution and unusual Al x Ge y intermetallic phases that do not form during near-equilibrium solidification. The microstructures are characterized and analyzed using a combination of selected area electron diffraction, high-resolution scanning transmission electron microscopy, energy dispersive X-ray spectroscopy to obtain high-resolution elemental maps, and atomistic modeling using density functional theory followed by atomic-scale image simulation. Depending on the local solidification conditions, the crystallography of the Al x Ge y intermetallic phases in the eutectic microstructure is either monoclinic (C 2/c) or monoclinic (P 2 1 ), with high densities of defects in both cases. This is in sharp contrast to the as-cast alloys that showed nominally pure Al and Ge phases with significant solute partitioning and equilibrium FCC and diamond cubic crystal structures, respectively. Corresponding kinetic phase diagrams are proposed to interpret the evolution of nano-lamellar eutectic morphologies with equilibrium Al and metastable Al x Ge y phases, and to explain increased solid solubility in the Al phases manifested by precipitation of ultrafine clusters of Ge. Furthermore, the reasons for the formation of these metastable eutectics under laser rapid solidification are discussed from the perspective of the competitive growth criterion.

Al-Ge eutectic↗
DOE OSTI2021

Fuel-cladding chemical interaction of a prototype annular U-10Zr fuel with Fe-12Cr ferritic/martensitic HT-9 cladding

As an alternative fuel form, the annular metallic fuel design eliminates the liquid sodium bond between the fuel and the cladding, providing back-end fuel cycle and other benefits. The fuel-cladding chemical interaction (FCCI) of annular fuel also presents new features. In this work, state-of-the-art electron microscopy and spectroscopy techniques were used to study the FCCI of a prototype annular U-10wt%Zr (U-10Zr) fuel with ferritic/martensitic HT-9 cladding irradiated to 3.3% fission per initial heavy atom. Compared with sodium-bonded solid fuels, negligible amounts of lanthanides were found in the FCCI layer in the investigated helium-bonded annular fuel. Instead, most lanthanides were retained in the newly formed UZr 2 phase in the fuel center region. The interdiffusion of iron and uranium resulted in tetragonal ( U ,Zr) 6 Fe phase (space group I4/mcm) and cubic ( U ,Zr)( Fe ,Cr) 2 phase (space group Fd 3 ¯ m). The ( U ,Zr)( Fe ,Cr) 2 phase contains a high density of voids and intergranular uranium monocarbides of NaCl-type crystal structure (space group Fm 3 ¯ m). At the interdiffusion zone and inner cladding interface, a porous lamellar structure composed of alternating Cr-rich layers and U-rich layers was observed. Next to the lamellar region, the unexpected phase transformation from body-centered cubic ferrite (α-Fe) to tetragonal binary Fe-Cr σ phase (space group P4 2 /mnm) occurred, and tetragonal Fe-Cr-U-Si phase (space group I4/mmm) was identified. Due to the diffusion of carbon into the interdiffusion zone, carbon depletion inside the HT-9 led to the disappearance of the martensite lath structure, and intergranular U-rich carbides formed as a result of the diffusion of uranium into the cladding. These detailed new findings reveal the unique features of the FCCI behavior of annular U-Zr fuels, which could be a promising alternative fuel form for high burnup fast reactor applications.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Mesoscale modeling of microstructure-dependent thermal conductivity in U-Zr fuels

In uranium-zirconium (U-Zr) based metallic fuels, different phases can form at different compositions and temperatures. Typically, lamellar δ-UZr 2 and α-U phases are the dominant microstructures in U-rich U-Zr alloys at temperatures below 880 K. In this work, a finite element method based mesoscale modeling technique is used to calculate the effective thermal conductivities of such heterogeneous microstructures, using the thermal conductivities of two individual phases and their interphase thermal resistance (Kapitza resistance) as input parameters. The Kapitza resistance between δ-UZr 2 and α-U is determined at different temperatures, which shows an approximately T 3 dependence in the temperature range between 300 and 800 K. In addition, the Kapitza resistance exhibits a strong dependence on the aspect ratio of the δ-UZr 2 phase. Further, an analytical model is therefore developed to quantify the effects of both temperature and δ-UZr 2 aspect ratio on the Kapitza resistance. Using this newly developed Kapitza resistance model, the effective thermal conductivities of a number of δ-UZr 2 + α-U heterogeneous microstructures in U-Zr alloys, including non-lamellar microstructures, can be estimated accurately.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗