Search NASA⌕ Search

SEARCH · Search NASA

Results for “passivation layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Long operating lifetime mid-infrared LEDs based on black phosphorus

Abstract Black phosphorus (BP) is a narrow bandgap layered semiconductor promising for mid-infrared optoelectronic applications. BP-based devices have been shown to surpass state-of-the-art mid-infrared detectors and light-emitting diodes (LEDs) in terms of performance. Despite their device advantages, the material’s inherent instability in the air could hinder its use in practical optoelectronic applications. Here, we investigated the impact of passivation on the device lifetime of BP LEDs, which deteriorate in a matter of seconds without using passivation. The lifetime is significantly extended with an Al 2 O 3 passivation layer and nitrogen packaging via atomic layer deposition and ultra-violet curable resin sealing. The operational lifetime (half-life) at room temperature is extrapolated to be ~15,000 h with an initial power density of 340 mW/cm 2 based on accelerated life testing. The present results indicate that efficient BP optoelectronics can be highly robust through simple and scalable packaging technologies, with important practical implications for mid-infrared applications.

42 ENGINEERING↗
DOE OSTI2025

Bias‐Dependent Quantum Efficiency Reveals Recombination Pathways in Thin Film Solar Cells

Identifying where recombination predominantly occurs—whether at the front interface, back interface, or throughout the bulk—is crucial for optimizing CdSeTe solar cells and many other photovoltaic device architectures. Here, a simple and effective diagnostic is demonstrated: measuring external quantum efficiency (QE) under varying forward biases. The drift–diffusion simulations reveal that each recombination pathway leaves a distinct bias-induced signature in the normalized QE: a progressive drop at long wavelengths for back-limited devices, a short-wavelength decline for front-limited devices, and a relatively uniform decrease across all wavelengths for bulk-limited devices. These predictions are validated with experiments on As-doped and Cu-doped CdSeTe devices, with and without passivation layers or different front buffers. In each case, the observed bias-dependent QE spectral changes align with the simulated recombination map. Because this method uses standard QE instrumentation, it offers a broadly accessible and cost-efficient means to diagnose recombination pathways—extending beyond CdSeTe to other thin-film and emerging solar cell technologies. By pinpointing recombination bottlenecks, researchers and manufacturers can strategically refine doping profiles, passivation schemes, and interface designs to further improve device performance.

CdTe↗
NASA NTRS1991

High voltage thermally diffused p(+)n solar cells

The possibility of fabricating thermally diffused p(+)n InP solar-cells with high open-circuit voltage without sacrificing the short circuit current is discussed. The p(+)n InP junctions were formed by Cd and Zn diffusion through a 3-5-nm-thick anodic or chemical phosphorus-rich oxide cap layer grown on n:InP:S (with ND-NA = 3.5 x 10 exp 16 and 4.5 x 10 exp 17/cu cm) Czochralski LEC-grown substrates. After thinning the emitter from its initial thickness of 1 to 2.5 micron down to 0.06-0.15 micron, the maximum efficiency was found when the emitter was 0.2 to 0.3 micron thick. Typical AM0, 25 C values of 854-860 mV were achieved for Voc, Jsc values were from 25.9 to 29.1 mA/sq cm using only the P-rich passivating layer left after the thinning process as an antireflection coating.

Faur, M.↗
DOE OSTI2026

Semi-Transparent Perovskite Solar Cells in a Stacked Tandem Module: Cooperative Research and Development Final Report, CRADA Number CRD-19-00810

This project seeks to develop device design, materials composition, and processing tools and parameters to fabricate semi-transparent perovskite solar cells and modules for application in stand-alone products or added to other solar cells in a mechanically stacked tandem configuration. This technology presents significant advanced manufacturing challenges and opportunities in getting to scale, including development of perovskite inks, scalable perovskite and heterojunction deposition and annealing processes, heterojunction composition, transparent electrode composition and deposition process, anti-reflection layer composition and deposition process, and cell to module integration processes. Modification 5: The proposed project seeks to develop device design, materials composition, and processing tools and parameters to fabricate semi-transparent perovskite solar cells and modules for application in stand-alone products or added to other solar cells in a mechanically-stacked tandem configuration. This technology presents significant advanced manufacturing challenges and opportunities in getting to scale, including development of perovskite inks, scalable perovskite and heterojunction deposition and annealing processes, heterojunction composition, transparent electrode composition and deposition process, passivation layers including in module scribes, anti-reflection layer composition and deposition process, and cell to module integration processes. Advanced metrology and characterization will be performed on perovskite films, cells and module. Furthermore, we will examine module or materials recycling for circular economy considerations. Modifcation 6: Gigahertz frequency microwave pump-probe spectroscopies are highly sensitive to thin film semiconductor photoconductivity of individual and stacks of layers that comprise perovskite solar cells. As such, these techniques will be used to qualify reproducibility and quality correlations during the manufacturing process. Modification 7: Mechanical adhesion of top contacts within perovskite modules significantly impacts the durability of the module when exposed to accelerated degradation testing. The adhesion between the perovskite/transport layer interface and the transport layer/top contact interface are both very sensitive small changes in processing. ALD processing conditions of the transport layer will be tuned to optimize the mechanical adhesion within the perovskite module stack.

14 SOLAR ENERGY↗
DOE OSTI2020

Impact of Cr and Co on 99Tc retention in magnetite: A combined study of ab initio molecular dynamics and experiments

This work explores the effect of co-mingled dopants, Co(II) and Cr(III), on Tc(IV) incorporation and retention in magnetite when heat treated to 625 or 700 °C. Key trends in Tc retention in the high temperature regime were identified using a combination of density-functional-theory based ab initio molecular dynamics (AIMD) simulations, and batch experiments including solid phase characterization techniques, e.g. X-ray absorption spectroscopy. A stabilizing effect on Tc(IV) was observed when the number of Tc and Cr atoms are equal or when the magnetite surface is oversaturated with Tc and Cr inclusions. Here, oversaturation is hypothesized to force Cr from the magnetite surface to form a Cr2O3 phase, which may act as a protective layer that prevents Tc release. With the addition of Co, Tc(IV) is stabilized via redox processes. The presence of Cr in low concentrations interferes with this redox stabilization and Cr is preferentially stabilized as opposed to Tc. As a result, using Co as a stabilizing dopant for Tc may be compromised in the presence of Cr. When the relative concentration of Tc, Cr and Co is the same, or more Co atoms are added to high Cr incorporated systems, the formation of the Cr2O3 phase may be suppressed. Although waste streams with co-mingled Tc and Cr potentially may benefit from a Co dopant, since the formation of a Cr2O3 passivation layer may protect incorporated Tc from being released, the relative concentration of the three elements will be a critical parameter for maximizing effectiveness of this strategy.

Lee, Mal Soon↗
NASA NTRS1998

X-Ray Photoelectron Spectroscopy Study of the Heating Effects on Pd/6H-SiC Schottky Structure

X-ray photoelectron spectroscopy is used to study the effects of heat treatment on the Pd/6H-SiC Schottky diode structure. After heating the structure at 425 C for 140 h, a very thin surface layer of PdO mixed with SiO(x) formed on the palladium surface of the Schottky structure. Heat treatment promoted interfacial diffusion and reaction which significantly broadened the interfacial region. In the interfacial region, the palladium concentration decreases with depth, and the interfacial products are Pd(x)Si (x = 1,2,3,4). In the high Pd concentration regions, Pd4Si is the major silicide component while gr and Pd2Si are major components in the low Pd concentration region. At the center of the interface, where the total palladium concentration equals that of silicon, the concentrations of palladium associated with various palladium silicides (Pd(x)Si, x= 1,2,3,4) are approximately equal. The surface passivation layer composed of PdO and SiO, may significantly affect the electronic and catalytic properties of the surface of the Schottky diode which plays a major role in gas detection. The electronic properties of the Schottky structure may be dominated by a (Pd+Pd(x)Si)/SiC interface. In order to stabilize the properties of the Schottky structure the surface and interface diffusion and reactions must be controlled.

Chen, Liang-Yu↗
DOE OSTI2025

Molecular Layer Deposited Aluminum‐Based Hybrid Resist for High‐Resolution Nanolithography and Direct Ultra‐High Aspect Ratio Pattern Transfer

Inorganic-containing hybrid photoresists are critical for next-generation extreme ultraviolet (EUV) lithography and angstrom-era semiconductor miniaturization. However, associated conventional solution processing struggles to achieve ultrathin, uniform films with high conformality and compositional control, limiting overall patterning performance. Here, this study reports the systematic lithographic patterning characterization of an Al-based hybrid resist synthesized via vapor-phase molecular layer deposition (MLD), using the trimethylaluminum (TMA) metal precursor and the hydroquinone (HQ) aromatic organic linker. The resist supports both sub-20 nm high-resolution nanolithography and virtually infinite silicon plasma etch selectivity. Lithographic performance studied using electron beam lithography (EBL) as a proxy for EUV shows that, under an optimized process adopting post-exposure bake, the resist achieves the best resolution of 15.4 nm linewidth under stringent 1:1 line-space high-density patterning—limited only by the minimum beam size of the EBL system. The resist also shows wide dose latitude and balanced performance in resolution, roughness, and sensitivity. The infinite silicon etch selectivity, stemming from spontaneous aluminum oxyfluoride passivation layer formation, enables fabrication of micrometer-tall, 40 nm-wide silicon nanofin structures using only a ≈30 nm-thick resist layer, without no hard mask. These results highlight the potential of MLD-based hybrid resists for developing next-generation resist materials for micro/nanoelectronics manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Selective oxidation and nickel enrichment hinders the repassivation kinetics of multi-principal element alloy surfaces

Robust and sustained corrosion resistance in multi-principal element alloys (MPEA) requires rapid repassivation, i.e. regrowth of the passive layer once it is damaged or destroyed at the surface. In this study, we show that the repassivation of Al 0.1 CrCoFeNi MPEA in 0.6 M NaCl solution is hindered at pH of ~ 2.4 - 6.8 due to the formation of a Ni-enriched subsurface layer as a result of selective oxidation and dissolution of several principal elements, which can be fully restored at pH of ~ 14 from the oxidation of all principal elements. Specifically, surface characterization via X-ray photoelectron spectroscopy (XPS), high-angle annular dark-field (HAADF) imaging in scanning transmission electron microscopy (STEM), and atom probe tomography (APT), are coupled with density functional theory (DFT) calculations to determine surface composition, oxidation state, and electron work function to uncover the structural origin of the pH-dependent repassivation mechanisms. It was found that selective oxidation of Cr, Co, and Fe in the acidic to neutral solutions altered the surface composition to be significantly enriched in Ni as compared to the bulk. Once the original passive film is destroyed locally by either pitting or tribocorrosion, this altered surface composition exhibited a much poorer repassivation capability due to the increased electron work function and reduced surface reactivity at higher Ni concentration. Finally, these understandings could shed light on the future compositional design of non-equiatomic MPEAs towards sustained repassivation and corrosion resistance over a wide pH range.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Localized corrosion at nm-scale hardening precipitates in Al-Cu-Li alloys

The localized corrosion of Li-containing nm hardening precipitates in the 3rd generation of Al-Cu-Li alloys was investigated based on a quasi in situ approach by sequentially exposing the material to NaCl solution and characterizing the structural, chemical, and electrochemical evolution at atomic scale using electron microscopy, spectroscopy, 3D tomography, electrochemical measurements, and DFT calculations. Localized corrosion of Al 7.5 Cu 4 Li (TB phase) initiated along {001} family of planes through the dealloying of Al and Li due to a low surface work function. Cu was enriched along the Cu (110) // T B (011) // Al (100) orientations on and around corroded T B precipitates. No strong galvanic interactions were observed at the T B and Al matrix interface due to the formation of a Li-C-O rich passivation layer during electrolyte exposure. Similarities and differences between T B and other common Al-Cu-Li precipitates (Al 2 CuLi, Al 6 CuLi 3 , and Al 3 Li) with respect to corrosion are discussed. Overall, the reported corrosion mechanism can assist in the assessment of the localized corrosion susceptibility of precipitation-hardened Al alloys and assist in the design of new alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hydration of alumina (Al 2 O 3 ) toward advancing aluminum particles for energy generation applications

Transforming metal particle combustion may require alteration of the metal oxide passivation shell surrounding the metal core. One approach for aluminum (Al) relies on the hydrated form of the metal oxide to incite surface reactions. Here, this study explores the conditions required for hydrating alumina (Al 2 O 3 ) particles and then extends those conditions toward hydration of the Al 2 O 3 passivation layer surrounding an Al core particle. By raising the pH of the water slurry to 11 and controlling temperature and time in slurry (i.e., aging), aluminum hydroxide Al(OH) 3 formation from Al 2 O 3 particles was optimized. The procedure was then extended to Al nanoparticles (nAl). Even though heating and extended aging time in slurry proved advantageous for Al 2 O 3 particles, these conditions were discarded for nAl particles because they favored formation of AlOOH, a less desirable hydrate. Through microscopy, spectroscopy, X-ray diffraction, and thermal analyses, results indicate that for a pH range of 11.26–11.56, the original Al 2 O 3 shell on Al particles transformed into Al(OH) 3 . Results indicate a feasible path forward towards producing new shell chemistries that may result in more directed energy from metal particle combustion.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Atomic layer deposition with passivation treatment

A method includes: 1) performing an atomic layer deposition cycle including (a) introducing precursors into a deposition chamber housing a substrate to deposit a material on the substrate; and (b) introducing a passivation gas into the deposition chamber to passivate a surface of the material; and 2) repeating 1) a plurality of times to form a film of the material.

Prinz, Friedrich B.↗
DOE OSTI2023

Long‐Life Lithium‐Metal Batteries with an Ultra‐High‐Nickel Cathode and Electrolytes with Bi‐Anion Activity

Abstract Anion chemistry in electrolytes can greatly dictate the nature and quality of passivation layers on both cathode and anode surfaces. This will be more significant when it comes to highly reactive Li‐metal anode and aggressive high‐nickel cathodes. Herein, a competitive bi‐anion activity is found in electrolytes with the co‐existence of two anions, which leads to a controlled Li‐salt decomposition kinetics and entirely favorable interphasial chemistry on both Li‐metal anode and ultrahigh‐nickel cathode. The proposed bi‐anion localized high‐concentration electrolytes are demonstrated to exhibit superior electrochemical compatibility toward Li metal and long‐term cycling stabilities under both 4.4 and 4.6 V in Li‐metal batteries with ultrahigh‐nickel cathode. This study sheds fresh light on dendrite‐free Li‐metal anodes and provides guidance to achieve high‐energy‐density batteries.

Chemistry↗
DOE OSTI2025

Designing Moderately‐Solvating Electrolytes for High‐Performance Lithium–Sulfur Batteries

New electrolytes are critical for high‐energy lithium (Li)–sulfur (S) batteries (LSBs) to ensure their stability against Li metal anode and polysulfides (PSs) shuttling which hinder the large‐scale application of LSBs. In this study, the design principle of moderately solvating electrolytes (MSEs) for LSBs is demonstrated by using a multiple‐solvent system comprising of a highly solvating solvent, a weakly solvating solvent, and a non‐solvating solvent to create a well‐balanced electrolyte system. This resulting electrolyte significantly improves the cycle life of LSBs, achieving 300 cycles, which is twice as long as that of similar cells with the conventional electrolyte and it also ensures stable calendar life for at least seven months. The optimal MSE forms robust passivation layers enhancing the structural integrity of both S and Li metal electrodes after cycling. These virtues effectively hinder parasitic side reactions and self‐discharge behavior of LSBs. This electrolyte design principle is versatile and can be applied to other battery chemistries, providing a potential path toward the development of a more efficient and stable battery system. By addressing key challenges such as the instability of electrodes and shuttling of polysulfides, this electrolyte approach offers promising solutions for advancing LSB technology.

25 ENERGY STORAGE↗
DOE OSTI2022

Over-Potential Tailored Thin and Dense Lithium Carbonate Growth in Solid Electrolyte Interphase for Advanced Lithium Ion Batteries

A stable solid electrolyte interphase (SEI) is highly desired to prevent parasitic reactions during normal operation of lithium-ion batteries (LIBs). Lithium carbonate (Li 2 CO 3 ) is one of the most significant components for smooth SEI passivation layers; while the formation mechanism and special distribution of the Li 2 CO 3 layer has not yet been illustrated. In this study, an over-potential tailored Li 2 CO 3 growth mechanism based on the typical hard carbon anode is demonstrated. With an increase in the over-potential, the size of Li 2 CO 3 decreases gradually as the amount increases. When the over-potential is large (potential at 0.01 V), a Li 2 CO 3 -rich thin and dense inorganic layer with the average thickness of 4.4 nm in the SEI is constructed. The special SEI the completely wraps the boundaries of the anode enables a larger Li-ion de-solvation energy barrier and a lower Li-ion diffusion energy barrier, which supports low self-discharge behavior and a fast kinetic rate at the anode. More generally, this Li 2 CO 3 growth mechanism is also applicable to commercialized graphite anodes and similar results are also obtained. Therefore, this work provides a new insight into the Li 2 CO 3 growth mechanism in SEIs, as well as a guideline for the design of stable artificial SEIs.

25 ENERGY STORAGE↗
DOE OSTI2024

Platinum/Tantalum Carbide Core–Shell Nanoparticles with Sub‐Monolayer Shells for Methanol and Oxygen Electrocatalysis

Abstract Core–shell architectures provide great opportunities to improve catalytic activity, but achieving nanoparticle stability under electrochemical cycling remains challenging. Herein, core–shell nanoparticles comprising atomically thin Pt shells over earth‐abundant TaC cores are synthesized and used as highly durable electrocatalysts for the methanol oxidation reaction (MOR) and the oxygen reduction reaction (ORR) needed to drive direct methanol fuel cells (DMFCs). Characterization data show that a thin oxidic passivation layer protects the TaC core from undergoing dissolution in the fuel cell‐relevant potential range, enabling the use of partially covered Pt/TaC core–shell nanoparticles for MOR and ORR with high stability and enhanced catalytic performance. Specifically, at the anode the surface‐oxidized TaC further enhances MOR activity compared to conventional Pt nanoparticles. At the cathode, the Pt/TaC catalyst feature increases tolerance to methanol crossover. These results show unique synergistic advantages of the core–shell particles and open opportunities to tailor catalytic properties for electrocatalytic reactions.

Chemistry↗
DOE OSTI2024

Effective Corrosion-Resistant Single-Atom Alloy Catalyst on HfO 2 -Passivated BiVO 4 Photoanode for Durable (≈800 h) Solar Water Oxidation

Green hydrogen (H 2 ) production from solar water splitting necessitates photoelectrodes with superior photoelectrochemical (PEC) activity and durability. However, surface defects and photocorrosion instability—especially at high potentials—limit PEC performance and stability. Herein, the prototypical bismuth vanadate (BiVO 4 ) photoanode is used to demonstrate a holistic approach to improve photocurrent density and long-term stability. In this approach, high surface-area nanostructuring of BiVO 4 is combined with barium (Ba) doping with semi-crystalline hafnium oxide (HfO 2 ) surface passivation and single-atom nickel platinum (NiPt) catalysts. The introduction of Ba 2+ ions into BiVO 4 increases the concentration of conductive V 4+ ions or the ratio of V 4+ ions to oxygen vacancies, avoiding V 5+ dissolution during water oxidation. The semi-crystalline HfO 2 , which serves as a passivation layer, prevents BiVO 4 photocorrosion by suppressing harmful chemical reactions when holes are transferred to the electrolyte. The synergistic use of isolated single-atom and Ni-Pt coordination improves charge transfer at the photoanode/electrolyte interface, leading to enhanced PEC kinetics and stability. As a result, a photoelectrode is demonstrated with ≈6.5 mA cm -2 at 1.23 V versus a reversible hydrogen electrode (RHE) and continuous operation for 800 h with a negligible degradation rate. This work provides a promising approach to improve photoanodes for PEC H 2 production.

08 HYDROGEN↗
DOE OSTI2025

A Universal Design of Lithium Anode via Dynamic Stability Strategy for Practical All‐Solid‐State Batteries

Abstract All‐solid‐state Li‐metal battery (ASSLB) chemistry with thin solid‐state electrolyte (SSE) membranes features high energy density and intrinsic safety but suffers from severe dendrite formation and poor interface contact during cycling, which hampers the practical application of rechargeable ASSLB. Here, we propose a universal design of thin Li‐metal anode (LMA) via a dynamic stability strategy to address these issues. The ultra‐thin LMA (20 μm) is in situ constructed with uniform highly Li‐ion conductive solid‐electrolyte interphase and composite‐polymer interphase (CPI) via electroplating process. As a result, the passivation layer with poor Li‐ion conduction on Li anode can be dissolved and small surface resistance can be achieved due to the good compatibility of CPI to SSEs. The cycling of Li symmetric cell with Li 6 PS 5 Cl thin film electrolyte (<100 μm) shows a high critical current density of >2.0 mA cm −2 with excellent cycling stability at 1.0 mA cm −2 . The ASSLBs paring with Ni‐rich LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode demonstrated the feasibility of engineered LMA design by presenting good rate capability from 0.1 C to 1.0 C at room temperature, as well as long‐term cycling stability (81 % retention after 100 cycles). This work represents a general pathway to make thin dendrite‐free LMA available for high‐energy‐density ASSLBs.

Deng, Tao [Department of Chemical and Biomolecular↗
DOE OSTI2025

A Universal Design of Lithium Anode via Dynamic Stability Strategy for Practical All‐Solid‐State Batteries

Abstract All‐solid‐state Li‐metal battery (ASSLB) chemistry with thin solid‐state electrolyte (SSE) membranes features high energy density and intrinsic safety but suffers from severe dendrite formation and poor interface contact during cycling, which hampers the practical application of rechargeable ASSLB. Here, we propose a universal design of thin Li‐metal anode (LMA) via a dynamic stability strategy to address these issues. The ultra‐thin LMA (20 μm) is in situ constructed with uniform highly Li‐ion conductive solid‐electrolyte interphase and composite‐polymer interphase (CPI) via electroplating process. As a result, the passivation layer with poor Li‐ion conduction on Li anode can be dissolved and small surface resistance can be achieved due to the good compatibility of CPI to SSEs. The cycling of Li symmetric cell with Li 6 PS 5 Cl thin film electrolyte (<100 μm) shows a high critical current density of >2.0 mA cm −2 with excellent cycling stability at 1.0 mA cm −2 . The ASSLBs paring with Ni‐rich LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode demonstrated the feasibility of engineered LMA design by presenting good rate capability from 0.1 C to 1.0 C at room temperature, as well as long‐term cycling stability (81 % retention after 100 cycles). This work represents a general pathway to make thin dendrite‐free LMA available for high‐energy‐density ASSLBs.

Deng, Tao [Department of Chemical and Biomolecular↗