Search NASA⌕ Search

SEARCH · Search NASA

Results for “rapid heating and cooling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Predicting Cement-Sheath Integrity with Consideration of Initial State of Stress and Thermoporoelastic Effects

In conventional wellbore-integrity analysis, the cement sheath’s initial state of stress and transient thermoporoelastic effects are often neglected. However, the initial state of stress is prerequisite information for accurately predicting the safe operating conditions that prevent a cemented well from being damaged. In addition, transient thermoporoelastic effects can have a profound effect on when damage will occur. Here in this paper, we propose a model that includes these effects to predict the safe operating pressures and temperatures that will prevent cement-sheath failure. For the initial state of stress, we proposed an empirical model using measurements. Subsequent stress changes are evaluated by a fully coupled transient thermoporoelastic model to analyze the mechanical behavior of the cement sheath. We predict the safe operating envelope (SOE) for shear, tensile, and debonding cement-sheath failures caused by pressure and temperature perturbations after the cement sets. Our model predicts that pore pressure is a key factor for cement failure, especially for rapid temperature changes. If the formation is low permeability, the transient pore pressures are amplified, causing the risk of damage to increase. Compared with conventional thermoelastic models, the thermoporoelastic model predicts a smaller SOE when heating the internal casing fluid and a larger envelope when cooling the internal casing fluid. Finally, the heating rate was considered with respect to field applications. The heating rate was also considered, and slower heating/cooling rates can prevent damage to the cement sheath. Finally, the thermoporoelastic model was applied to explain several laboratory and field experiments and achieved good matches.

02 PETROLEUM↗
DOE OSTI2024

Rapid cooling of the in-plane motion of two-dimensional ion crystals in a Penning trap to millikelvin temperatures

Here, we propose a highly feasible technique with no experimental overhead to rapidly cool the in-plane degrees of freedom of large two-dimensional ion crystals in Penning traps. Through simulations, we demonstrate that our approach enables the in-plane modes to cool down to a temperature of around 1 mK in less than 10 ms. Our technique relies on near-resonant coupling of the poorly cooled in-plane motions and the efficiently cooled out-of-plane motions, and is achieved without introducing additional potentials. The rapid cooling enabled by our approach is in contrast to typical operating conditions, where our simulations of the laser cooling dynamics suggest that the ion crystal's in-plane motion cools very slowly on a timescale of several hundreds of milliseconds, a rate likely slower than experimental heating rates. Our work sets the stage for sub-Doppler laser cooling of the planar motion, and more robust and versatile quantum simulation and quantum sensing experiments with two-dimensional crystals in Penning traps.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Incommensurate magnetic ordering and a possible structural transition in EuIn 4

Single crystals of EuIn 4 were grown and 151 Eu Mössbauer spectroscopy, combined with temperature dependent electrical resistance, specific heat and anisotropic magnetization measurements have been used to investigate the magnetic ordering of monoclinic EuIn 4 . Here, we find two closely spaced magnetic transitions (at ~10 K and ~11 K). The initial ordering leads to an incommensurate sinusoidally modulated structure that squares up rapidly on cooling through the lower (10 K) transition. Well above the magnetic transitions we observe an additional transition at ~130 K which may also involve two closely spaced events. This upper transition(s) is most likely structural and offers no suggestion of magnetic nature either in magnetization or Mössbauer data.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Glass formation during combinatorial sputtering in binary alloys

Glass formation is a complex phenomenon influenced by thermodynamic and kinetic aspects, which are often controlled by extrinsic contributions. While bulk metallic glasses are typically multicomponent alloys, binary alloys offer a simplified approach to studying glass formation. In this study, we fabricated 57 binary alloy systems through combinatorial sputtering, where each alloy system is represented in 66 different alloys. We developed an automated analysis to determine structure and composition using X-ray diffraction and energy-dispersive X-ray spectroscopy for over 3700 alloys. We found that ∼17 % of the alloys form glasses under the estimated cooling rate during sputtering of ∼10 8 K/s. Data analysis revealed that commonly used factors like atomic size ratio and heat of mixing are ineffective in predicting glass formation. However, the crystal structure mismatch of the alloys’ elements emerged as the strongest indicator of glass formation under sputtering conditions of binary alloys. Here, the differences in glass formation under slow cooling rates used for bulk glass formation and the here observed glass formation under rapid cooling rates are discussed.

Binary alloys↗
DOE OSTI2022

Uncertainty Quantification of Monolithic Tungsten Target Block Fatigue

The current STS spallation target design consists of 21 water cooled, tantalum clad, monolithic tungsten blocks. The target wheel assembly rotates such that each target block receives a direct proton pulse every 1.4 seconds (21 blocks / 15 Hz pulses). The quasi-steady heating induced by the repetitive beam pulses creates a significant mean stress distribution in the target. On top of this, the rapid energy deposition from a proton pulse induces dynamic stress waves that are of the same order of magnitude as the mean stresses. Over the design goal of 5,000 operational hours per year for a decade, each target must withstand over 130 million repetitions of these dynamic stress events. The fatigue life prediction of the target blocks is a complex sequence of simulations that depend upon a set of input parameters. For the tungsten block, the end goal is the fatigue factor-of-safety (FOS). This study documents a new structural analysis routine using software available to U.S. national laboratories (e.g. CUBIT, Sierra Multiphysics, Dakota) that enables more rapid target fatigue analysis. The increased throughput is amenable to parameter sensitivity and uncertainty quantification (UQ) studies. A set of input parameters (ultimate strength, fatigue strength, density, elastic modulus, Poisson’s ratio, thermal conductivity, coefficient of thermal expansion, specific heat, flow rate) with expected ranges are documented based on literature data, recent experimental testing, and engineering judgement. UQ bounds the resulting fatigue FOS at [0.5, 3.4] using epistemic interval analysis. These bounds are expected to be wider due to model effects (discretization) and beam effects (focus, offset) that were not included. Parameter sensitivity underscores the importance of ultimate strength and fatigue strength of irradiated tungsten on the fatigue calculations.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Cooling Delays from Iron Sedimentation and Iron Inner Cores in White Dwarfs

Do white dwarfs have inner cores made of iron? Neutron-rich nuclei like 56 Fe experience a net gravitational force and sediment toward the core. Using new phase diagrams and molecular dynamics simulations, we show that 56 Fe should separate into mesoscopic Fe-rich crystallites due to its large charge relative to the background. At solar abundances, these crystallites rapidly precipitate and form an inner core of order 100 km and 10 -3 M ⊙ that may be detectable with asteroseismology. Associated cooling delays could be up to a Gyr for low-mass white dwarfs but are only ~0.1 Gyr for massive white dwarfs, so while this mechanism may contribute to the Q-branch the heating is insufficient to fully explain it.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Structure characterization and steam oxidation performance of U 3 Si 2 with Zr alloying additions

Research and development of high uranium density fuels supports the on-going effort to enhance reactor technology, safety, performance, and economics. Among high uranium density fuels, U 3 Si 2 is a favored fuel candidate due to its higher uranium density and improved thermal conductivity when compared to traditional UO 2 . While U 3 Si 2 demonstrates an improved fuel economy, it suffers from rapid degradation when exposed to water at T > 300°C. In order for U 3 Si 2 to be implemented in water cooled reactors, the water reaction must be understood and mitigated. Reported here is the performance of Zr alloying additions to U 3 Si 2 exposed to high temperature steam oxidation environments. Here, the investigation shows that homogenization heat treatment contributes to a delayed onset of oxidation and an improved homogeneity throughout the arc-melt fabricated alloyed compositions. Of the pre- and post-annealed samples, the post-annealed 7 vol% Zr addition exhibited the highest onset temperature of oxidation. A preliminary computational investigation to complement the experimental analysis assesses the solubility of Zr in U 3 Si 2 and its incorporation in the crystal lattice.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Metal additively manufactured wavy fin cold-plate architecture for improved thermal-hydraulic performance

Rapid growth in artificial intelligence and data center workloads demands high-performance liquid cooling to manage increasing chip power. This study presents two metal-additive-manufactured cold plates with sinusoidal fins, constant-amplitude wavy fins and linearly variable-amplitude wavy fins and compares them against metal-additive-manufactured straight fins using experiments conducted at 1 kW heat dissipation as well as high-fidelity 3D conjugate computational fluid dynamic simulations. The cold plates were printed in AlSi10Mg material and underwent design using a Python-automated workflow prior to manufacture and testing. The experiments show that wavy fins reduce the normalized thermal resistance by 35 to 45 % at water flow rates from 1 to 4 LPM. At a fixed 20 kPa pressure drop, the variable-waviness design lowered peak surface temperature by 9 °C and thermal resistance by 51 %, while edge-channel maldistribution in the constant wavy fin design limited gains. A thermal resistance breakdown revealed that 55–63 % of the total thermal resistance in wavy designs comes from base heat conduction, 27–33 % from fin heat conduction, and 9–13 % from fin heat convection, indicating the need to address conduction bottlenecks. Parametric sweeps identify a 3 mm fin pitch as optimal, and that horizontal inlet/outlet manifolds further reduce pressure drop by 30–60 % and thermal resistance by 9–16 % relative to vertical inlet-outlet manifolds. The results yield comprehensive guidelines for fin geometry, manifold alignment, material selection and additive-manufacturing constraints to realize high-performance liquid-cooled cold plates for power-dense electronics.

3d printing↗
DOE OSTI2023

Microstructural and phase changes in alpha uranium investigated via in-situ studies and molecular dynamics

A deeper knowledge of thermally induced microstructural and phase evolution in nuclear metallic fuel can be obtained using novel in-situ microscopic analyses. Such studies can provide information on the dynamics of phase transitions which is not possible with conventional postmortem characterization (post-irradiation examination). In this work, the behavior of alpha uranium (α-U) was investigated via in-situ heating tests in a transmission electron microscope. Here, the main objective is to understand the microstructural and phase changes, such as defect annihilation and ß phase formation and retention, observed in reactor in-pile transient studies at the Transient Reactor Test facility. Indeed, defect migration and rearrangement were observed within the α phase starting at 673 K; α→ß phase transition was observed between 773 K and 1,073 K during the heating ramp (which is in the temperature window reported for α→ß transition temperatures). Recrystallization and formation of nano grains was observed at high temperatures (over 1,073 K). Such recrystallization was possibly related to the formation of the γ phase. Finally, it was indeed observed that the ß phase (but not γ phase) was retained at room temperature upon rapid cooling. Molecular dynamics studies support these experimental results and shows that the γ phase of pure uranium cannot be retained at room temperature if not stabilized with the addition of an alloying element.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

A review of challenges, barriers, and opportunities for large-scale deployment of cool surfaces

Major urban centers are warming due to a combination of global and local phenomena. City governments are increasingly adopting strategies to mitigate the causes and impacts of extreme heat on their populations. Among these strategies are high solar-reflectance (cool) surfaces installed on building roofs and walls. Use of cool surfaces is a cost-effective and simple strategy that replaces conventional darker surfaces with surfaces that have a high reflectance to shortwave (solar) energy. This report reviews the recent history of cool-surface deployment efforts. This includes peer-reviewed literature, conference proceedings, and grey literature to identify challenges and barriers to wide-scale deployment of cool surfaces. We have also researched heat action plans and programs from cities and different codes and standards, as well as available incentive and rebate programs. The review identifies challenges, barriers, and opportunities associated with large-scale deployment of cool surfaces and categorize them broadly as being related to product development & performance or policies & mandates. It provides a foundation upon which we intend to build a roadmap for rapidly accelerating future deployments of cool surfaces. Finally, this roadmap will address identified challenges and incorporate lessons learned from historical efforts to generate a practical and actionable plan.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Laser Powder Directed Energy Deposition of Steels for Nuclear Applications

This comprehensive investigation examines the structure–property relationships in two nuclear alloy systems—Alloy 709 (A709) austenitic stainless steel and Grade 92 (G-92) ferritic/martensitic (F/M) steel—manufactured via directed energy deposition (DED) for sodium-cooled fast reactor applications. This study establishes the fundamental mechanisms for controlling microstructures for optimizing the mechanical performance of additively manufactured nuclear materials through systematic heat treatment optimization and multiscale characterization. As-deposited A709 steel develops a complex multiscale strengthening architecture consisting of a fine cellular solidification structure with diameter of 2-3 µm within10–50 µm grains, elevated dislocation densities from rapid thermal cycling, and grain boundary precipitates that activate concurrent Hall–Petch, dislocation, and precipitation hardening mechanisms to achieve exceptional properties [yield strength (YS): 603 MPa, ultimate tensile strength (UTS): 844 MPa, Vickers hardness: 220 HV] that achieve a 44% superior strength compared to that of the wrought material. Heat treatments produce different results. Solution annealing (SA) dissolves the cellular structure and reduces the hardness to 190 HV. Precipitation treatment (PT) keeps the cellular structure but adds carbides, allowing the hardness to reach 205 HV. The best approach combines both treatments (SA+PT) and creates uniform precipitate distributions with M 23 C 6 carbides at the grain boundaries and MX carbonitrides in the matrix, achieving a hardness of 195 HV. However, directional differences persist, with a 12%–15% strength variation between orientations due to the inherited layered microstructural architecture that survives aggressive heat treatment. While tensile testing at 550°C demonstrates 40%–50% thermal softening with dynamic strain aging, DED A709 steel still maintains a 71% higher YS than that of the wrought material. Ion irradiation studies (100–400 dpa) of DED A709 steel reveal progressive radiation damage with increasing void density and radiation-induced segregation causing nickel enrichment and chromium depletion, which will ultimately compromise mechanical properties. As-deposited G-92 exhibits exceptional strength (UTS: 1650–1700 MPa, 430 HV) through a complex microstructure containing both ferrite and martensite phases, a high geometrically necessary dislocation (GND) density (17.04×10 14 /m 2 ), and fine carbides. Heat treatments create distinct changes. Normalizing produces fresh martensite with the highest hardness (460 HV) and an increased GND density (20.23×10 14 /m 2 ). Tempering develops dual precipitation systems and reduces the hardness to 290 HV. The optimal approach uses sequential normalizing plus tempering, achieving balanced properties with the lowest hardness (250 HV) and a reduced GND density (11.01×10 14 /m 2 ). A processing-dependent anisotropy is observed: horizontal specimens achieve superior ductile behavior, while vertical specimens exhibit brittle failure. A tempering heat treatment successfully mitigates this anisotropic behavior by transforming the hard martensitic as-deposited structure into tempered martensite enabling both horizontal and vertical specimens to exhibit similar stress–strain characteristics with visible necking behavior. Remarkably, testing at 550°C reveals a reversal in the anisotropy, where as-deposited specimens achieve near isotropy with superior thermal stability (a 15%–20% strength reduction), while tempered specimens develop an orientation dependence with a 25%–30% strength reduction. Both alloy systems demonstrate that DED processing creates specimens with a superior strength through refined microstructural features, though with distinct strengthening mechanisms—austenitic through cellular structures and precipitates versus F/M through phase transformations and precipitates. Heat treatment optimization requires alloy-specific approaches, with A709 benefiting from controlled precipitation while G-92 requires careful phase transformation control. The results show that DED manufacturing can produce nuclear materials with exceptional performance, but directional effects and temperature-dependent behavior must be carefully considered for reactor component design and qualification.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Dual Purpose – Heating & Cooling – Thermal Battery for Flexible and Energy-Efficient Heat Pump Systems

The integration of heat pumps with thermal energy storage (HP-TES) systems is gaining attention as a viable solution for managing peak building demand driven by immense cooling and heating loads. With growing reliance on renewable energy sources, thermal energy storage offers an excellent opportunity to mitigate mismatches in thermal load between energy supply and demand. The use of phase-change material (PCM) TES is especially promising, as PCMs offer significant latent energy storage capacity with smaller temperature glides in smaller volumes compared to other TES technologies. However, challenges arise because current HP-TES architectures can load-shift only cooling or heating, not both, requiring two systems and thus doubling cost, weight, and footprint. Furthermore, current research efforts lack specific tools and techniques to advance integrated systems from concept design to end-user application, focusing on only discharge performance. To address these challenges, this research proposes a dual-mode (heating and cooling) integrated HP-TES system that uses room-temperature PCM-TES as a high-temperature heat source in heating mode and a low-temperature heat sink in cooling mode, thereby reducing temperature lifts and compressor power. Design criteria for PCM-TES heat exchangers were developed, balancing thermal-hydraulic performance with practical constraints such as available building space and weight requirements along with PCM selection considerations such as shipping conditions, moisture exposure, and number of available cycles. A detailed transient model for HP-TES systems was developed to enable rapid annual performance assessments in any US climate zone.

42 ENGINEERING↗
DOE OSTI2026

Processing iridium foil targets for the production of radioplatinum isotopes

Dissolving noble metals remains challenging because of their high reduction potentials and tendency to passivate as oxides. This barrier is acute for iridium metal targets used to produce platinum radioisotopes, where post-irradiation processing is costly and hazardous with conventional routes. Here, we report a rapid alkali-fusion method that converts Ir metal directly into chloride media compatible with downstream separations. In the process, an Ir foil is fused with Na 2 O 2 and KCl at temperatures above the KCl melting point; the molten salt enhances heat transfer and facilitates O 2− /Na + transport to the Ir surface, overcoming Ir's oxidation resistance. The fused cake is then cooled and leached in 10 M HCl, yielding Ir in solution without specialized microwave digestion or HF. Pt separation from bulk Ir was evaluated using extraction-chromatography resins. A newly formulated ionic-liquid resin containing Cyphos IL 104 (E104) was compared with two commercial resins (TrisKem TK200 and TK201). All resins achieved >90 % Ir recovery. Pt co-recovery depended on resin chemistry: TK200 recovered 85.9 % Pt, TK201 recovered 54.1 % Pt, and E104 recovered 72.9 % Pt. This study introduces a fast, scalable dissolution route for solid Ir targets and demonstrates resin choices that tune Ir/Pt separation, lowering the barrier to routine production and purification of Pt radioisotopes.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2021

Doppler-Lidar Evaluation of HRRR-Model Skill at Simulating Summertime Wind Regimes in the Columbia River Basin during WFIP2

Complex-terrain locations often have repeatable near-surface wind patterns, such as synoptic gap flows and local thermally forced flows. An example is the Columbia River Valley in east-central Oregon-Washington, a significant wind-energy-generation region and the site of the Second Wind-Forecast Improvement Project (WFIP2). Data from three Doppler lidars deployed during WFIP2 define and characterize summertime wind regimes and their large-scale contexts, and provide insight into NWP model errors by examining differences in the ability of a model [NOAA’s High-Resolution Rapid-Refresh (HRRR-version1)] to forecast wind-speed profiles for different regimes. Seven regimes were identified based on daily time series of the lidar-measured rotor-layer winds, which then suggested two broad categories. First, in three regimes the primary dynamic forcing was the large-scale pressure gradient. Second, in two regimes the dominant forcing was the diurnal heating-cooling cycle (regional sea-breeze-type dynamics), including the marine intrusion previously described, which generates strong nocturnal winds over the region. The other two included a hybrid regime and a non-conforming regime. For the large-scale pressure-gradient regimes, HRRR had wind-speed biases of ~1 m s -1 and RMSEs of 2-3 m s -1 . Errors were much larger for the thermally forced regimes, owing to the premature demise of the strong nocturnal flow in HRRR. Thus, the more dominant the role of surface heating in generating the flow, the larger the errors. Major errors could result from surface heating of the atmosphere, boundary-layer responses to that heating, and associated terrain interactions. Finally, measurement/modeling research programs should be aimed at determining which modeled processes produce the largest errors, so those processes can be improved and errors reduced.

17 WIND ENERGY↗
DOE OSTI2021

Enhanced biomechanical performance of additively manufactured Ti-6Al-4V bone plates

As the global trauma fixation devices market expands rapidly, it is imperative to improve the production of fixation devices through enhanced design accuracy and fit for best performance and maximum patient comfort. Selective laser melting (SLM) is one of the mature additive manufacturing methods, which provides a viable route for the rapid production of such devices. In this work, the ability of SLM to produce near-net-shape parts, as desired for medical implants, was utilized for the fabrication of bone plates from Ti-6Al-4V alloy powder. Martensitic microstructure obtained after the printing of alloy resulted in poor ductility, limiting its application in the field of orthopedics. A specially designed repeated cyclic heating and cooling close to but below the β-transus was used to transform from acicular to a bimodal microstructure without the need for plastic deformation prior to heat treatment for improving the ductility. Bone plates subjected to this heat treatment were mechanically tested by means of tensile and 3-point bend tests and demonstrated large improvement in ductility, and the values were comparable to those similar plates prepared from wrought alloy. Other important properties required for implants were assessed, such as corrosion resistance in simulated body fluid and cytocompatibility in vitro using MC3T3-E1 cells. These results for the bone plate after heat treatment were excellent and similar to those of the additively manufactured and wrought plates. Taken together, the performance of the additively manufactured bone plates after subjecting to heat treatment was similar to those of bone plate manufactured using wrought alloy. These results have important implications for the fabrication of patient-specific metallic orthopedic devices using SLM without compromising their biomechanical performance by subjecting them to a tailored heat treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2023

SPT-CL J2215−3537: A Massive Starburst at the Center of the Most Distant Relaxed Galaxy Cluster

Abstract We present the discovery of the most distant, dynamically relaxed cool core cluster, SPT-CL J2215−3537 (SPT2215), and its central brightest cluster galaxy (BCG) at z = 1.16. Using new X-ray observations, we demonstrate that SPT2215 harbors a strong cool core with a central cooling time of 200 Myr (at 10 kpc) and a maximal intracluster medium cooling rate of 1900 ± 400 M ⊙ yr −1 . This prodigious cooling may be responsible for fueling the extended, star-forming filaments observed in Hubble Space Telescope imaging. Based on new spectrophotometric data, we detect bright [O ii ] emission in the BCG, implying an unobscured star formation rate (SFR) of 320 − 140 + 230 M ⊙ yr −1 . The detection of a weak radio source (2.0 ± 0.8 mJy at 0.8 GHz) suggests ongoing feedback from an active galactic nucleus (AGN), though the implied jet power is less than half the cooling luminosity of the hot gas, consistent with cooling overpowering heating. The extreme cooling and SFR of SPT2215 are rare among known cool core clusters, and it is even more remarkable that we observe these at such high redshift, when most clusters are still dynamically disturbed. The high mass of this cluster, coupled with the fact that it is dynamically relaxed with a highly isolated BCG, suggests that it is an exceptionally rare system that must have formed very rapidly in the early universe. Combined with the high SFR, SPT2215 may be a high- z analog of the Phoenix cluster, potentially providing insight into the limits of AGN feedback and star formation in the most massive galaxies.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Kinetically stabilized ferroelectricity in bulk single-crystalline HfO 2 :Y

HfO 2 , a simple binary oxide, exhibits ultra-scalable ferroelectricity integrable into silicon technology. This material has a polymorphic nature, with the polar orthorhombic (Pbc2 1 ) form in ultrathin films regarded as the plausible cause of ferroelectricity but thought not to be attainable in bulk crystals. In this work, using a state-of-the-art laser-diode-heated floating zone technique, we report the Pbc2 1 phase and ferroelectricity in bulk single-crystalline HfO 2 :Y as well as the presence of the antipolar Pbca phase at different Y concentrations. Neutron diffraction and atomic imaging demonstrate (anti)polar crystallographic signatures and abundant 90°/180° ferroelectric domains in addition to switchable polarization with negligible wake-up effects. Density-functional-theory calculations indicate that the yttrium doping and rapid cooling are the key factors for stabilization of the desired phase in bulk. Our observations provide insights into the polymorphic nature and phase control of HfO 2 , remove the upper size limit for ferroelectricity and suggest directions towards next-generation ferroelectric devices.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Magnetic, thermal, and electronic-transport properties of EuMg 2 Bi 2 single crystals

The trigonal compound EuMg 2 Bi 2 has recently been discussed in terms of its topological band properties. These are intertwined with its magnetic properties. In this paper detailed studies of the magnetic, thermal, and electronic-transport properties of EuMg 2 Bi 2 single crystals are presented. The Eu + 2 spins 7/2 in EuMg 2 Bi 2 exhibit an antiferromagnetic (AFM) transition at a temperature T N = 6.7 K, as previously reported. By analyzing the anisotropic magnetic susceptibility χ data below T N in terms of molecular-field theory (MFT), the AFM structure is inferred to be a c -axis helix, where the ordered moments in the hexagonal a b -plane layers are aligned ferromagnetically in the a b plane with a turn angle between the moments in adjacent moment planes along the c axis of ≈ 120 ° . An alternate but less likely magnetic structure is a planar structure with nearest-neighbor Eu spins aligned at ≈ 120 ° with respect to each other, where these ordered-moment layers are stacked along the c axis. The magnetic heat capacity exhibits a λ anomaly at T N with evidence of dynamic short-range magnetic fluctuations both above and below T N . The high- T limit of the magnetic entropy is close to the theoretical value for spins 7/2. The in-plane electrical resistivity ρ ( T ) data indicate metallic character with a mild and disorder-sensitive upturn below T min = 23 K. An anomalous rapid drop in ρ ( T ) on cooling below T N as found in zero field is replaced by a two-step decrease in magnetic fields. The ρ ( T ) measurements also reveal an additional transition below T N in applied fields of unknown origin that is not observed in the other measurements and may be associated with an incommensurate to commensurate AFM transition. The dependence of T N on the c -axis magnetic field H ⊥ was derived from the field-dependent χ ( T ) , C p ( T ) , and ρ ( T ) measurements. This T N ( H ⊥ ) was found to be consistent with the prediction of MFT for a c -axis helix with S = 7 / 2 and was used to generate a phase diagram in the H ⊥ – T plane.

36 MATERIALS SCIENCE↗