Search NASA⌕ Search

SEARCH · Search NASA

Results for “representativeness analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

BayoTech Risk and Modeling Support of NM Gas Site

The BayoTech hydrogen generation system has been evaluated in terms of safety considerations at the NM Gas site. The consequence of a leak in different components in the system was evaluated in terms of plume dispersion and overpressure. Additionally, the likelihood of a leak scenario for different hydrogen components was identified. The worst-case plume dispersion cases, full-bore leaks, resulted in relatively large plumes. However, these cases were noted to be far less likely than the partial break cases that were evaluated. The partial break cases resulted in nearly negligible plume lengths. Similarly, the overpressure analysis of the full-bore break scenarios resulted in much larger overpressures than the partial break cases (which resulted in negligible overpressure at the lot line). There were several cases evaluated in the analysis that represented leak scenarios from both hydrogen and natural gas sources. Generally, the natural gas leak scenarios resulted in a smaller horizontal impact than that of hydrogen leaks. The worst-case consequence from a hydrogen leak resulted from the compressors, storage pods, or dispensing system. To consider the safety features that may isolate the leak, the consequence was evaluated at different times after the leak event to show the reduction of pressure. After 2 seconds, the plume dispersion from this event is contained within the perimeter of the site. The worst-case consequences show that the plume may disperse to adjacent facilities and to the street. When considering both likelihood and consequence, the risk may be considered low because the maximum frequency of a full-bore leak from any component within the hydrogen compound is 8.2 E-5/yr. This means that a full-bore leak is expected to occur less than once every 10,000 years. The risk can be further reduced by implementing mitigative countermeasures, such as CMU walls along the sides of the equipment compound. This would reduce the overall consequence of the worst-case dispersion scenarios (horizontal impact of plume). In terms of siting and safety analysis, the NFPA 2 code was used to provide a high-level evaluation of the current site plan. The most limiting equipment in terms of set-back distance are the compressors/storage units because of the high-pressure hydrogen. The site layout was evaluated for an acceptable location for the compression/storage unit based on NFPA 2 set-back distances. It is important to note that the NFPA 2 set-back distances consider both likelihood and consequence. This is important because the worst-case results evaluated herein also represent the least likely leak scenario. Other site-specific considerations were evaluated, including the parking shade structure with photovoltaic cells and refueling vehicles. These issues were dispositioned and determined to not present a safety risk.

08 HYDROGEN↗

A techno-economic framework for comparing conventionally and additively manufactured parts for geothermal applications

Geothermal reservoir characterization, construction, and operations are technology-intensive activities that contribute significantly to the cost of delivering renewable electricity. The technologies involved, such as downhole tools and drilling equipment, are similar to those used in oil and gas exploration and production must often be adapted for use in the corrosive, high-temperature geothermal reservoir environment. Low production volume of geothermal tools presents a major challenge in meeting the industry's technology needs. Production of specialized tools for geothermal subsurface applications is often cost-prohibitive. Reduced inventory of subsurface well construction, characterization, and production tools causes geothermal reservoir development efficiency and sophistication to lag behind that of the oil and gas industry. Advances in additive manufacturing provide opportunities to advance geothermal technology while reducing lead time and costs associated with production of low-volume, complex parts. Additionally, this paper performs an initial techno-economic analysis comparing the cost of conventional production techniques and additive manufacturing for geothermal downhole applications. An analysis of representative downhole tools is used to create a framework for estimating fabrication costs of subtractive and additive techniques, including post-print machining required to meet final tolerances. The framework is used to explore several manufacturing scenarios and identify the dominant factors driving manufacturing time and cost. The current feasibility of additive manufacturing for geothermal downhole tool applications is assessed and issues for future development to better meet the needs of the geothermal industry are identified.

36 MATERIALS SCIENCE↗

Adaptive sparse polynomial chaos expansion based on least angle regression

Polynomial chaos (PC) expansions are used in stochastic finite element analysis to represent the random model response by a set of coefficients in a suitable (so-called polynomial chaos) basis. The number of terms to be computed grows dramatically with the size of the input random vector, which makes the computational cost of classical solution schemes (may it be intrusive (i.e. of Galerkin type) or non intrusive) unaffordable when the deterministic finite element model is expensive to evaluate. To address such problems, the paper describes a non intrusive method that builds a sparse PC expansion. First, an original strategy for truncating the PC expansions, based on hyperbolic index sets, is proposed. Then an adaptive algorithm based on least angle regression (LAR) is devised for automatically detecting the significant coefficients of the PC expansion. Beside the sparsity of the basis, the experimental design used at each step of the algorithm is systematically complemented in order to avoid the overfitting phenomenon. The accuracy of the PC metamodel is checked using an estimate inspired by statistical learning theory, namely the corrected leave-one-out error. As a consequence, a rather small number of PC terms are eventually retained (sparse representation), which may be obtained at a reduced computational cost compared to the classical 'full' PC approximation. The convergence of the algorithm is shown on an analytical function. Then the method is illustrated on three stochastic finite element problems. The first model features 10 input random variables, whereas the two others involve an input random field, which is discretized into 38 and 30 - 500 random variables, respectively.

97 MATHEMATICS AND COMPUTING↗

Do we have globally representative data to understand soil processes?

Understanding and modeling soils and soil organic matter (SOM) are central to a variety of human needs, from food production to ecosystem management. Soil data have been collected for over a century, but the global spatial and process representativeness of soil data remains unclear. We assessed the representativeness of currently available soil data that could be used to understand a variety of SOM processes. We used 16 open-source soil databases and data from over 281,000 unique locations globally, categorizing the databases into three main data types necessary to understand SOM processes: soil carbon stocks and fluxes, mechanistic drivers of these stocks and fluxes, and soil carbon gain or loss potential. We found that stock and driver data have extensive global coverage. However, data on soil carbon gain or loss potential, particularly data describing change in soils over time such as time series data, are severely limited in their global coverage. We conclude that while significant strides have been made in measuring soil carbon stocks and fluxes, and their drivers, we are limited in global data related to changes in soils over time. Our recommendations for soil data generators are to ensure precise metadata reporting and prioritizing sampling in underrepresented areas like tropical, arctic, mountainous, wetland and arid regions. We also encourage designing revisit schemes that explicitly support change detection and reporting multi-modal datasets that can aid in model development. Targeted measurement of low coverage soil data types and regions is necessary for a range of applications including current and future biogeochemical predictions, and their management and policy implications.

carbon fluxes↗

Neutron and X-Ray Diffraction Studies of Advanced Materials

The selection of articles in the special topic 'Neutron and X-Ray Studies of Advanced Materials' is based on the materials presented during the TMS 2009 annual meeting in San Francisco, CA, February 15-19, 2009. The development of ultrabrilliant third-generation synchrotron X-ray sources, together with advances in X-ray optics, has created intense X-ray microbeams, which provide the best opportunities for in-depth understanding of mechanical behavior in a broad spectrum of materials. Important applications include ultrasensitive elemental detection by X-ray fluorescence/absorption and microdiffraction to identify phase and strain with submicrometer spatial resolution. X-ray microdiffraction is a particularly exciting application compared with alternative probes of crystalline structure, orientation, and strain. X-ray microdiffraction is nondestructive with good strain resolution, competitive or superior spatial resolution in thick samples, and with the ability to probe below the sample surface. Moreover, the high-energy X-ray diffraction technique provides an effective tool for characterizing the mechanical and functional behavior in various environments (temperature, stress, and magnetic field). At the same time, some neutron diffraction instruments constructed mainly for the purpose of engineering applications can be found at nearly all neutron facilities. The first generation-dedicated instruments designed for studying in-situ mechanical behavior have been commissioned and used, and industrial standards for reliable and repeatable measurements have been developed. Furthermore, higher penetration of neutron beams into most engineering materials provides direct measurements on the distribution of various stresses (i.e., types I, II, and III) beneath the surface up to several millimeters, even tens of millimeters for important industrial components. With X-ray and neutron measurements, it is possible to characterize material behavior at different length scales. It is predicted that the application of these techniques, in combination with theoretical simulations and numerical modeling, will lead to major breakthroughs in materials science in the foreseeable future, which will contribute to the development of materials technology and industrial innovation. Specifically, the use of these techniques provides bulk material properties that further augment new characterization tools including the increased use of atom probe tomography and high-resolution transmission electron microscopy systems. The combination of these techniques greatly assists the material property models that address multi-length-scale mechanisms. Different applications of diffuse scattering for understanding the fundamental materials properties are illustrated in the articles of Welberry et al., Goossens and Welberry, Campbell, Abe et al., Gilles et al., and Zhang et al. Analysis of thin films and two-dimensional structures is described in the articles of Gramlich et al., Brock et al., Vigliante et al., Kuzel et al., and Davydok et al. Recent advances in the line profile analysis are represented by the the articles of Scardi et al., Ungar et al., and Woo et al. Characterization of modern alloys is presented by the articles of Wollmershauser et al., Eidenberger et al., Garlea et al., Jia et al., Soulami et al., Wilson et al., and Wang et al. The collected articles are written by different scientific X-ray and neutron research groups. They represent a general trend in the development and application of diffraction techniques all over the world.

36 MATERIALS SCIENCE↗

Energy efficiency and thermal resilience analysis for row houses using representative building energy models

Row houses, a prevalent medium-density urban archetype, were popularized during industrial era to accommodate the working class in the U.S. cities. Today, many of these structures are deteriorating, exacerbating the energy cost for residents with limited economic resources. Moreover, many households that lack Air Conditioning (AC) are vulnerable to extreme summer heat, an issue expected to worsen in the future. Energy-efficient retrofits can help mitigate these challenges. However, current literature provides limited insight into how existing building energy codes impact the energy efficiency and thermal resilience of row houses in current and future weather scenarios. This study provides a detailed method to address this gap by employing calibrated representative energy models of row houses as a baseline, and evaluating the annual energy savings and summertime thermal safety improvements from code compliant retrofits under current and future typical weather conditions. Using Baltimore City as a case study, results show that under current weather, retrofitting row houses yields significant energy savings along with notable thermal resilience improvements. The end unit row house realizes higher energy savings, whereas the interior unit experiences greater thermal resilience improvement after retrofitting. In future, retrofitted row houses can still save energy, but residents will face numerous hours of fatal indoor temperatures without AC in summer. Additionally, findings reveal stark zone-wise variations in thermal safety, and elevated humidity risks in certain zones post-retrofit, emphasizing the need for zonal retrofit strategies and better natural ventilation strategies.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Variation in the Gross Tumor Volume and Clinical Target Volume for Preoperative Radiotherapy of Primary Large High-Grade Soft Tissue Sarcoma of the Extremity Among RTOG Sarcoma Radiation Oncologists

Purpose: To evaluate variability in the definition of preoperative radiotherapy gross tumor volume (GTV) and clinical target volume (CTV) delineated by sarcoma radiation oncologists. Methods and Materials: Extremity sarcoma planning CT images along with the corresponding diagnostic MRI from two patients were distributed to 10 Radiation Therapy Oncology Group sarcoma radiation oncologists with instructions to define GTV and CTV using standardized guidelines. The CT data with contours were then returned for central analysis. Contours representing statistically corrected 95% (V95) and 100% (V100) agreement were computed for each structure. Results: For the GTV, the minimum, maximum, mean (SD) volumes (mL) were 674, 798, 752 {+-} 35 for the lower extremity case and 383, 543, 447 {+-} 46 for the upper extremity case. The volume (cc) of the union, V95 and V100 were 882, 761, and 752 for the lower, and 587, 461, and 455 for the upper extremity, respectively. The overall GTV agreement was judged to be almost perfect in both lower and upper extremity cases (kappa = 0.9 [p < 0.0001] and kappa = 0.86 [p < 0.0001]). For the CTV, the minimum, maximum, mean (SD) volumes (mL) were 1145, 1911, 1605 {+-} 211 for the lower extremity case and 637, 1246, 1006 {+-} 180 for the upper extremity case. The volume (cc) of the union, V95, and V100 were 2094, 1609, and 1593 for the lower, and 1533, 1020, and 965 for the upper extremity cases, respectively. The overall CTV agreement was judged to be almost perfect in the lower extremity case (kappa = 0.85 [p < 0.0001]) but only substantial in the upper extremity case (kappa = 0.77 [p < 0.0001]). Conclusions: Almost perfect agreement existed in the GTV of these two representative cases. Tshere was no significant disagreement in the CTV of the lower extremity, but variation in the CTV of upper extremity was seen, perhaps related to the positional differences between the planning CT and the diagnostic MRI.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Application of Failure Mode and Effects Analysis to Intraoperative Radiation Therapy Using Mobile Electron Linear Accelerators

Purpose: Failure mode and effects analysis (FMEA) represents a prospective approach for risk assessment. A multidisciplinary working group of the Italian Association for Medical Physics applied FMEA to electron beam intraoperative radiation therapy (IORT) delivered using mobile linear accelerators, aiming at preventing accidental exposures to the patient. Methods and Materials: FMEA was applied to the IORT process, for the stages of the treatment delivery and verification, and consisted of three steps: 1) identification of the involved subprocesses; 2) identification and ranking of the potential failure modes, together with their causes and effects, using the risk probability number (RPN) scoring system, based on the product of three parameters (severity, frequency of occurrence and detectability, each ranging from 1 to 10); 3) identification of additional safety measures to be proposed for process quality and safety improvement. RPN upper threshold for little concern of risk was set at 125. Results: Twenty-four subprocesses were identified. Ten potential failure modes were found and scored, in terms of RPN, in the range of 42-216. The most critical failure modes consisted of internal shield misalignment, wrong Monitor Unit calculation and incorrect data entry at treatment console. Potential causes of failure included shield displacement, human errors, such as underestimation of CTV extension, mainly because of lack of adequate training and time pressures, failure in the communication between operators, and machine malfunctioning. The main effects of failure were represented by CTV underdose, wrong dose distribution and/or delivery, unintended normal tissue irradiation. As additional safety measures, the utilization of a dedicated staff for IORT, double-checking of MU calculation and data entry and finally implementation of in vivo dosimetry were suggested. Conclusions: FMEA appeared as a useful tool for prospective evaluation of patient safety in radiotherapy. The application of this method to IORT lead to identify three safety measures for risk mitigation.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Establishing a process-structure-property-performance framework for SLS additive manufacturing through integrated multiscale modeling

This study presents a comprehensive suite of high-fidelity computational models that integrate multiscale and multiphysics simulations to capture the full Selective Laser Sintering (SLS) additive manufacturing process—from initial melting and solidification to mechanical response under external loads. Process simulations are linked with mechanical analysis through Representative Volume Elements (RVEs), establishing a process-structure–property-performance framework. The interaction between laser light and polyamide 12 (PA12) powder is modeled, accounting for laser characteristics and the optical, thermal, and geometrical properties of the powder. The heat source is incorporated into a heat transfer model, coupled with crystallization kinetics and densification models to predict material density and crystallinity. The porosity distribution from the densification model and crystallinity interpolated from experimental data are used to construct the RVEs. A multi-mechanism constitutive model is then calibrated using mechanical tests to predict the stress–strain response. Simulation results show good agreement with experimental data in terms of porosity, crystallinity, and mechanical performance when sufficient laser power (62 W or higher) is used. This research supports the inverse design of 3D-printed structures by introducing a high-fidelity framework that combines multiscale and multiphysics modeling with experimental calibration for predictive and performance-driven additive manufacturing.

SLS↗

Two new barium indium phosphates with intersecting tunnel structures: BaIn{sub 2}P{sub 4}O{sub 14}, and Ba{sub 3}In{sub 2}P{sub 4}O{sub 16}

Two new barium indium phosphates BaIn{sub 2}P{sub 4}O{sub 14} and Ba{sub 3}In{sub 2}P{sub 4}O{sub 16} were synthesized by high temperature solution growth method and structurally characterized by single crystal X-ray diffraction analysis. They represent first compounds in the Ba-In-P-O systems. BaIn{sub 2}P{sub 4}O{sub 14} and Ba{sub 3}In{sub 2}P{sub 4}O{sub 16} display different types of 3D architectures. The projections of both structures concern about the existence of the intersecting tunnels. In compound BaIn{sub 2}P{sub 4}O{sub 14}, the tunnels are built up of the corner-sharing InO{sub 6} octahedra and P{sub 2}O{sub 7} groups, whereas in compound Ba{sub 3}In{sub 2}P{sub 4}O{sub 16}, they are formed by corner sharing of PO{sub 4} tetrahedra and InO{sub 6} octahedra. The electronic band structure calculations of two compounds have been performed with the density functional theory method. The study of calculations and optical diffuse reflectance experimental results show both compounds are insulators with direct band-gap.

36 MATERIALS SCIENCE↗

A systems engineering framework for the optimization of food supply chains under circular economy considerations

The current linear “take-make-waste-extractive” model leads to the depletion of natural resources and environmental degradation. Circular Economy (CE) aims to address these impacts by building supply chains that are restorative, regenerative, and environmentally benign. This can be achieved through the re-utilization of products and materials, the extensive usage of renewable energy sources, and ultimately by closing any open material loops. Such a transition towards environmental, economic and social advancements requires analytical tools for quantitative evaluation of the alternative pathways. Here, in this work, we present a novel CE system engineering framework and decision-making tool for the modeling and optimization of food supply chains. First, the alternative pathways for the production of the desired product and the valorization of wastes and by-products are identified. Then, a Resource-Task-Network representation that captures all these pathways is utilized, based on which a mixed-integer linear programming model is developed. This approach allows the holistic modeling and optimization of the entire food supply chain, taking into account any of its special characteristics, potential constraints as well as different objectives. Considering that typically CE introduces multiple, often conflicting objectives, we deploy here a multi-objective optimization strategy for trade-off analysis. A representative case study for the supply chain of coffee is discussed, illustrating the steps and the applicability of the framework. Single and multi-objective optimization formulations under five different coffee-product demand scenarios are presented. The production of instant coffee as the only final product is shown to be the least energy and environmental efficient scenario. On the contrary, the production solely of whole beans sets a hypothetical upper bound on the optimal energy and environmental utilization. In both problems presented, the amount of energy generated is significant due to the utilization of waste generated for the production of excess energy.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Soiling and cleaning: Initial observations from 5-year photovoltaic glass coating durability study

The contamination of solar photovoltaic cover glass can significantly reduce the transmittance of light to the surface of the photovoltaic cell, reducing the module's power output. The solar industry has been developing antireflection (AR) and antisoiling (AS) surface coatings to enhance light transmittance and mitigate the impacts of soiling. Although uncoated glass has been field tested for decades, minimal data exist to demonstrate the durability of AR and AS coatings against abrasion and surface erosion, including from: natural weathering, airborne sand, and industry cleaning practices. Coupons 75 mm square of varying types have been field-deployed to gather long-term data on coating durability; the initial results are presented here after 1 year of outdoor exposure near Sacramento, California. Duplicate sets of coupons were cleaned monthly per four different cleaning practices. All coupons demonstrated inorganic soiling as well as microscale biological contamination, regardless of cleaning method. Additionally, full-sized, field-aged modules from other areas of the world presented with similar types of contamination as the field-aged coupons; micrographs and results from genomic sequencing of this contamination are included here. Optical microscopy, scanning electron microscopy, atomic force microscopy/energy-dispersive spectroscopy, surface roughness, transmittance, and surface energy analysis of representative specimens and cleaning practices are presented.

14 SOLAR ENERGY↗

4-(Pyrazol-4-yl)-pyrimidines as Selective Inhibitors of Cyclin-Dependent Kinase 4/6

Identification and structure-guided optimization of a series of 4-(pyrazol-4-yl)-pyrimidines as selective CDK4/6 inhibitors is reported herein. Several potency and selectivity determinants were established based on the X-ray crystallographic analysis of representative compounds bound to monomeric CDK6. Significant selectivity for CDK4/6 over CDK1 and CDK2 was demonstrated with several compounds in both enzymatic and cellular assays.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Conserved Structural Elements in the V3 Crown of HIV-1 gp120

Binding of the third variable region (V3) of the HIV-1 envelope glycoprotein gp120 to the cell-surface coreceptors CCR5 or CXCR4 during viral entry suggests that there are conserved structural elements in this sequence-variable region. These conserved elements could serve as epitopes to be targeted by a vaccine against HIV-1. Here we perform a systematic structural analysis of representative human anti-V3 monoclonal antibodies in complex with V3 peptides, revealing that the crown of V3 has four conserved structural elements: an arch, a band, a hydrophobic core and the peptide backbone. These are either unaffected by or are subject to minimal sequence variation. As these regions are targeted by cross-clade neutralizing human antibodies, they provide a blueprint for the design of vaccine immunogens that could elicit broadly cross-reactive protective antibodies.

59 BASIC BIOLOGICAL SCIENCES↗

A mobile system for a comprehensive online-characterization of nanoparticle aggregates based on wide-angle light scattering and laser-induced incandescence

A mobile demonstrator for the comprehensive online-characterization of gas-borne nanoparticle aggregates is presented. Two optical measurement techniques are combined, both utilizing a pulsed Nd:YAG laser as light source. Aggregate size and fractal dimension are measured by Wide-Angle Light Scattering (WALS). An ellipsoidal mirror images elastically scattered light from scattering angles between 10° and 165° onto a CCD-camera chip resulting in an almost complete scattering diagram with high angular resolution. Primary particle size and volume fraction are measured by time-resolved Laser-Induced Incandescence (TiRe-LII). Here, particles are heated up to about 3000 K by the short laser pulse, the enhanced thermal radiation signal is detected with gated photomultiplier tubes. Analysis of the signal decay time and maximum LII-signal allows for the determination of primary particle diameter and volume fraction. The performance of the system is demonstrated by combined measurements on soot nanoparticle aggregates from a soot aerosol generator. Particle and aggregate sizes are varied by using different equivalence ratios of the combustion in the generator. Soot volume fraction can be adjusted by different levels of dilution with air. Online-measurements were carried out demonstrating the favorable performance of the system and the potential for industrial applications such as process control and product development. The particle properties obtained are confirmed through transmission electron microscopy analysis on representative samples.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Applying the index of watershed integrity to the Matanuska–Susitna basin

The Matanuska-Susitna Borough is the fastest growing region in the State of Alaska and is impacted by a number of human activities. We conducted a multiscale assessment of the stressors facing the borough by developing and mapping the Index of Watershed Integrity (IWI) and Index of Catchment Integrity (the latter considers stressors in areas surrounding individual stream segments exclusive of upstream areas). The assessment coincided with the borough’s stormwater management planning. We adapted the list of anthropogenic stressors used in the original conterminous United States IWI application to reflect the borough’s geography, human activity, and data availability. This analysis also represents an early application of the NHDPlus High Resolution geospatial framework and the first use of the framework in an IWI study. We also explored how remediation of one important stressor, culverts, could impact watershed integrity at the catchment and watershed scales. Overall, we found that the integrity scores for the Matanuska– Susitna basin were high compared to the conterminous United States. Low integrity scores did occur in the rapidly developing Wasilla–Palmer core area. We also found that culvert remediation had a larger proportional impact in catchments with fewer stressors.

54 ENVIRONMENTAL SCIENCES↗

Cosmological constraints on decaying dark matter

We present a complete analysis of the cosmological constraints on decaying dark matter. Previous analyses have used the cosmic microwave background and Type Ia supernova. We have updated them with the latest data as well as extended the analysis with the inclusion of Lyman-α forest, large scale structure and weak lensing observations. Astrophysical constraints are not considered in the present paper. The bounds on the lifetime of decaying dark matter are dominated by either the late-time integrated Sachs-Wolfe effect for the scenario with weak reionization, or CMB polarization observations when there is significant reionization. For the respective scenarios, the lifetimes for decaying dark matter are Γ{sup −1} ∼> 100 Gyr and (fΓ){sup −1} ∼> 5.3 × 10{sup 8} Gyr (at 95.4% confidence level), where the phenomenological parameter f is the fraction of the decay energy deposited in baryonic gas. This allows us to constrain particle physics models with dark matter candidates through investigation of dark matter decays into Standard Model particles via effective operators. For decaying dark matter of ∼ 100 GeV mass, we found that the size of the coupling constant in the effective dimension-4 operators responsible for dark matter decay has to generically be ∼< 10{sup −22}. We have also explored the implications of our analysis for representative models in theories of gauge-mediated supersymmetry breaking, minimal supergravity and little Higgs.

79 ASTRONOMY AND ASTROPHYSICS↗