SEARCH · Search NASA

Results for “work hardening”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Report on partially complete post-irradiation-examination of the INL samples

Ferritic-martensitic steels (NF616 and T91), and austenitic stainless steel 800H and its Grain Boundary Engineering (GBE)-treated version 800H-TMP (ThermoMechanical Processing) were irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) and their microstructures and mechanical properties were characterized. Ferritic-martensitic steels were irradiated up to 8.16 dpa in the irradiation temperatures ranging from 241 °C to 447.5 °C. Selected 800H and 800H-TMP samples were also irradiated up to 9.12 dpa at 359°C to 431°C. Vickers hardness measurement, fractography, and microstructural characterization were performed on the selected samples in the LAMDA lab. Radiation-induced hardening of NF616 and T91 was observed in the hardness measurements which show ~37% to ~65% increases, depending on irradiation dose and irradiation temperature. Within the irradiation conditions studied in this work, samples with a higher dose had a higher hardness. All the tested alloy 800H and 800H-TMP in this work showed irradiation-hardening by ~96±7% to ~152±10%. Alloy 800HTMP tended to have slightly smaller irradiation-hardening than alloy 800H. The fractography of NF616 samples D2 (2.96 dpa at 291.5°C), D4 (5.91 dpa at 359°C), and D6 (8.16 dpa at 431°C) indicated loss of ductility with negligible necking for the sample D2, yet obvious ductile failure for samples D4 and D6. Fractography of alloy 800H samples N4 (7.27 dpa at 359°C), N5 (3.9 dpa at 451.5°C), and N6 (9.01 dpa at 431°C), and alloy 800H-TMP samples P4 (7.36 dpa at 359°C), P5 (3.95 dpa at 451.5°C), and P6 (9.12 dpa at 431°C) indicated that all samples failed in a ductile mode, with obvious necking. Dimples were observed where large Ti-containing particles were observed for the samples. TEM characterization was performed on alloy 800H (N4, N5, N6) and 800H-TMP (P4, P5 and P6). Accumulation of M23C6 precipitates at grain boundaries was observed in all samples, and the presence of Ti(C,N) precipitates at grain boundaries and in the matrix was observed in alloy 800H-TMP. M23C6 precipitates were found to have the cube-on-cube orientation relationship with the matrix. In addition, nanoscale Si-rich clusters were observed in the matrix of all samples. Atom probe tomography was conducted on the same samples, and their results are being analyzed to be integrated with the TEM results for a confident description of the clustering behavior. Due to the low irradiation temperature (up to 451.5°C), dislocation loops formed in all samples, with the density and the average size of dislocation loops in the order of 1022 – 1023 m-3 and 11.7 – 15.9 nm, respectively. The loop densities in alloy 800H were higher than that in alloy 800H-TMP under the same irradiation conditions. Further systematic data analyses, together with some complementary experiments, will be pursued for these samples to foster peer-reviewed journal article publications.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2020

Second Annual Progress Report on Correlation Between Microstructure and Mechanical Properties of Neutron-Irradiated Ferritic-Martensitic and Austenitic Steels

Ferritic-martensitic steels G92-2b (an optimized Grade 92 heat), NF616 and T91, and austenitic stainless steel 800H and its Grain Boundary Engineering (GBE)-treated version 800H-TMP (ThermoMechanical Processing) were irradiated in the High Flux Isotope Reactor (HFIR) of Oak Ridge National Laboratory (ORNL) and the Advanced Test Reactor (ATR) of Idaho National Laboratory (INL). Selected G92-2b samples were irradiated up to 14.66 dpa in the HFIR at two temperature ranges: 400–496.7°C and 683.3– 720°C. NF616 and T91 were irradiated in the ATR up to 8.16 dpa with the irradiation temperatures ranged from 241°C to 447.5°C. Alloy 800H and 800H-TMP samples were irradiated in both the HFIR and the ATR. Selected 800H and 800H-TMP samples had HFIR irradiation to 1.28 dpa at 580°C and ATR irradiation up to 9.12 dpa at 359°C to 431°C. Vickers hardness measurements, fractography, and microstructural characterization were performed on the selected samples in the Low Activation Materials Design and Analysis (LAMDA) laboratory. Radiation-hardening of G92-2b was observed at the lower doses and lower irradiation temperatures (400- 496.7°C), with GB03 (0.52 dpa at 400°C) and GB04 (7.44 dpa at ~490°C) showing ~12% and ~8% hardening, respectively. Softening by ~14% was observed for GB05 (14.66 dpa at 496.7°C). Radiationsoftening of G92-2b was more prevalent at the higher irradiation temperatures (683.3-~720°C), with GB10 (0.46 dpa at 683.3°C), GB11 (7.44 dpa at ~720°C), and GB12 (14.63 dpa at ~720°C) showing ~8%, ~8%, and ~40% softening, respectively. Radiation-hardening of NF616 and T91 was observed with the hardness increased by ~37% to ~65% depending on the irradiation doses and irradiation temperatures. Within the studied irradiation conditions of NF616 and T91, samples with a higher dose had a larger hardness after irradiation. All the tested alloy 800H and 800H-TMP samples in this work showed radiation-hardening by ~96±7% to ~152±10%. Alloy 800H-TMP tended to have slightly smaller radiation-hardening than alloy 800H. The fractography results of G92-2b sample GB03, GB10, and GB11, together with the previously characterized fractography of GB04, GB05, and GB12, indicated that the ductility of G92-2b was maintained up to 14.66 dpa at the lower irradiation temperatures of 400-496.7°C, while some loss of ductility (less necking) was observed for higher doses at the higher irradiation temperatures of 683.3-720°C. This agrees with the previously reported tensile test results of G92-2b, where the elongation of G92-2b was reduced at higher doses at the higher irradiation temperatures. Dimple sizes increased at higher doses, which are more evident at the higher irradiation temperatures of 683.3-~720°C. The fractography of NF616 sample D2 (2.96 dpa at 291.5°C), D4 (5.91 dpa at 359°C), and D6 (8.16 dpa at 431°C) indicated loss of ductility with negligible necking for sample D2, while ductile failure for samples D4 and D6. Fractography of alloy 800H and 800H-TMP samples in various irradiation conditions showed ductile failure with obvious necking. Dimples were observed, with some of them containing large Ti-rich particles, in all the 800H/800H-TMP samples. Electron backscatter diffraction characterization of GB12 indicated the recovery of the lath structure, which was generally replaced by an equiaxed grain structure. Transmission electron microscopy (TEM) characterization showed the presence of frequent M 23 C 6 (M = primarily Cr), MX (M = primarily V), spherical Nb(C,N) precipitates, and occasional Laves phase precipitates in the G92-2b samples. MX precipitates with sizes of 20-30 nm were observed at boundaries of smaller grains, indicating the pinning effect of the V-rich precipitates. The lath structure recovery was more evident at the higher irradiation temperatures (683.3-~720°C), with decreased densities of line dislocations and M23C6 precipitates. The irradiated T91 (TA04) showed the growth of M23C6 precipitates to 101 ± 40 nm from the initial 68 ± 22 nm in the unirradiated condition. Dislocation loops of both {100} and {111} types were present in TA04. TEM characterization was also performed on the irradiated 800H (N4, N5, N6, and AR2) and 800H-TMP (P4, P5, P6, and HG1). Accumulation of M 23 C 6 precipitates at grain boundaries was observed in all the xii 800H/800H-TMP samples, and the presence of Ti(C,N) precipitates at grain boundaries and in the matrix was observed in the irradiated 800H-TMP. Some Ti(C,N) precipitates are embedded in the M 23 C 6 precipitates, maintaining specific orientation relationships between the precipitates and between the precipitate and matrix. In addition, nanoscale Si-rich clusters were observed in the matrix of all the 800H/800H-TMP samples, with EDS Si maps tending to have a lower contrast in 800H-TMP samples. Atom probe tomography was conducted on the same samples, supported by a Rapid Turnaround Examination project under Nuclear Science User Facilities. The results are being analyzed to be integrated with the TEM results for a confident description of the γ’ precipitates. Dislocation loops also formed in all the 800H/800H-TMP samples. The density and the average size of dislocation loops were quantified to be in the order of 10 22 – 10 23 m -3 and 11.7 – 15.9 nm, respectively, in the ATR-irradiated 800H/800H-TMP samples. The loop densities in irradiated 800H were higher than that in irradiated 800H-TMP under the same irradiation conditions. Further systematic data analyses, together with some complementary experiments, will be pursued for these samples to foster peer-reviewed journal article publications.

36 MATERIALS SCIENCE↗

DOE OSTI2024

PVDF-based backsheet cracking: Mapping in situ phase evolution by X-ray scattering

One of the most common polymers used in commercial photovoltaic backsheets is polyvinylidene fluoride (PVDF). However, recent reports have shown the potential for PVDF-based backsheets to crack and fail prematurely. Previous work has suggested that polymer phase changes play a role in the failure mechanism. Here, in situ wide-angle X-ray scattering maps are used to show that α- to β-phase transformations occur at crack tips in aged PVDF-based backsheets under stretching. Substantial β-phase formation is shown to be associated with strain hardening. In addition, our work demonstrates that β-phase formation is not required for crack growth and only occurs at crack tips when plastic deformation of the PVDF polymer has occurred. In conclusion, the anisotropy in the strength of aged PVDF-based backsheets is linked to the lack of β-phase formation when strain is applied to aged backsheets in the transverse direction.

14 SOLAR ENERGY↗

DOE OSTI2021

Constructing high-performance radiation-resistant ternary YSZ-MgO-CNT nanocomposites via tailored nanostructures

Developing long-lifetime bulk-form ceramic-based materials with high irradiation resistance is crucial for advanced nuclear systems. Here, we incorporated carbon nanotubes (CNTs) into yttria-stabilized zirconia (YSZ) and magnesia (MgO) nanocrystals to fabricate bulk YSZ-MgO-CNT nanocomposites with abundant ternary nanostructures by spark plasma sintering. To understand the role of tailored ternary nanostructure on irradiation, we investigated the microstructure and mechanical properties evolutions of the YSZ-MgO-CNT nanocomposites irradiated by multi-energy He + ions at high temperature to different fluences. Compared with the single-phase YSZ and ultrafine-grained YSZ-MgO composites, the YSZ-MgO-CNT nanocomposites possessed higher ability to manage irradiation-induced He bubbles/defects via the defect-interface interactions of proposed “loading-unloading” and “loading-transporting-unloading” mechanisms for controlling the dynamical behaviors of He atoms/defects in the CNT-doped ternary nanostructures, thereby presenting more stable microstructure and better performance in resisting irradiation hardening. In conclusion, this work provides insight into the design of advanced inert matrix nuclear fuel and new nuclear waste management materials.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Ultrafine-grained Fe-TiB 2 high-modulus nanocomposite steel with high strength and isotropic mechanical properties by laser powder bed fusion

Fe-TiB 2 metal matrix composite, also called high-modulus steels (HMSs), are of great interest for applications in fuel-efficient transportation infrastructure, aerospace, and wear industries due to their high specific stiffness and yield strength. However, conventional cast Fe-TiB 2 HMSs often contain coarse and sharp-edged TiB 2 particles which easily trigger premature cracking during loading. Here, we synthesized a Fe-TiB 2 nanocomposite HMS via laser powder bed fusion (LPBF) additive manufacturing of mixed micro-sized powders of Fe, Ti, and Fe 2 B. We investigated the microstructure formation and mechanical behavior of the Fe-TiB 2 HMS. We found that in situ chemical reaction of Ti and Fe 2 B enables the formation of TiB 2 particles at nanoscale during rapid solidification of LPBF. These nanoscale TiB 2 particles can serve as heterogeneous nucleation sites and promote the formation of ultrafine and equiaxed α-Fe grains with random crystallographic textures, which differ from many other additively manufactured (AM) metal alloys characteristic of strong crystallographic textures. As such, isotropic mechanical properties were achieved in the AM Fe-TiB 2 nanocomposite HMS with a high elastic modulus of ~ 240 GPa, an exceptional yield strength of ~ 1450 MPa, and a large plasticity of ~ 20% under compression. Quantitative analysis reveals that the high yield strength primarily originates from strengthening contributions of the ultrafine grains with an average grain size of ~450 nm, the nanoscale TiB 2 reinforcing particles of 20–180 nm, and a high density of printing-induced dislocations of the order of 10 15 m –2 . In situ synchrotron high-energy X-ray diffraction unveils the load partitioning from the softer α-Fe matrix to the stiffer and stronger TiB 2 nanoparticles, contributing to the sustained strain hardening during compression. Our work not only provides a general pathway for achieving high-performance metal matrix nanocomposites by in situ chemical reaction and precipitation of ceramic nanoparticles during additive manufacturing, but also offers mechanistic insights into the deformation mechanism of nanoparticle-reinforced HMS composites.

36 MATERIALS SCIENCE↗

DOE OSTI2024

High entropy ceramics for applications in extreme environments

Abstract Compositionally complex materials have demonstrated extraordinary promise for structural robustness in extreme environments. Of these, the most commonly thought of are high entropy alloys, where chemical complexity grants uncommon combinations of hardness, ductility, and thermal resilience. In contrast to these metal–metal bonded systems, the addition of ionic and covalent bonding has led to the discovery of high entropy ceramics (HECs). These materials also possess outstanding structural, thermal, and chemical robustness but with a far greater variety of functional properties which enable access to continuously controllable magnetic, electronic, and optical phenomena. In this experimentally focused perspective, we outline the potential for HECs in functional applications under extreme environments, where intrinsic stability may provide a new path toward inherently hardened device design. Current works on high entropy carbides, actinide bearing ceramics, and high entropy oxides are reviewed in the areas of radiation, high temperature, and corrosion tolerance where the role of local disorder is shown to create pathways toward self-healing and structural robustness. In this context, new strategies for creating future electronic, magnetic, and optical devices to be operated in harsh environments are outlined.

36 MATERIALS SCIENCE↗

DOE OSTI2025

HPC for Optimizing Process Parameters to Control Material Evolution in Seamless Induction Hardening of Wind Turbine Main Shaft Bearings

Work proposed in this project focused on understanding the effect of martensitic transformation in the steel on the potential for cracking during seamless induction hardening (SIH) as a function of process conditions to allow the process to optimally scale up. Large-scale, three-dimensional phase-field simulations of martensitic transformation were performed using MEUMAPPS-SS (Microstructure Evolution Using Massively Parallel Phase-field Simulations – Solid State) code developed at Oak Ridge National Laboratory. The simulations were guided by location-specific thermal history generated by experimental measurements of time-temperature history generated at The Timken Company. The simulations were able to capture the morphological evolution of the martensite variants in an Fe-1.0C-1.5Cr steel based on the Nishiyama-Wasserman (NW) orientation relationship. The simulations were also able to quantify the stress-state at the interface between impinging martensite variants. The simulations indicated that the magnitude of the various stress and strain components were dependent on the sizes of the impinging plates with a reduction in these quantities with reduced plate size in agreement with experimental findings. The results obtained from the simulations will be used to guide the optimization of the alloy thermal conditions to eliminate quench cracking during SIH of bearing steels.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2025

HPC for optimizing process parameters to control material evolution in seamless induction hardening of wind turbine main shaft bearings

17 WIND ENERGY↗

DOE OSTI2022

The influence of temperature on the strain-hardening behavior of Fe-22/25/28Mn-3Al-3Si TRIP/TWIP steels

In this work, the influence of temperature and stacking fault energy (SFE) on the strain-hardening behavior and critical resolved shear stress for twinning was investigated for three Fe–22/25/28Mn–3Al–3Si wt.% transformation- and twinning-induced plasticity (TRIP/TWIP) steels. The SFEs were calculated by two different methods, density functional theory and statistical thermodynamic modeling. The dislocation structure, observed at low levels of plastic deformation, transitions from “planar” to “wavy” dislocation glide with an increase in temperature, Mn content, and/or SFE. The change in dislocation glide mechanisms from planar to wavy reduces the strain hardening rate, in part due to fewer planar obstacles and greater cross slip activity. Additionally, the alloys exhibit a large decrease in strength and ductility with increasing temperature from 25 to 200 °C, attributed to a substantial reduction in the thermally activated component of the flow stress, predominate suppression of TRIP and TWIP, and a significant increase in the critical resolved shear stress for mechanical twinning. Interestingly, the increase in SFE with temperature had a rather minor influence on the critical resolved shear stress for mechanical twinning, and other temperature dependent factors which likely play a more dominant role are discussed.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Synergic grain boundary segregation and precipitation in W- and W-Mo-containing high-entropy borides

The structures of W- and W-Mo-containing high-entropy borides (HEBs) are systematically studied by combining atomic-resolution transmission electron microscopy imaging, electron diffraction, and chemical analysis. Here, we reveal that W or W-Mo addition in HEBs leads to segregation of these elements to the grain boundaries (GBs). In the meantime, W- or W-Mo-rich precipitates also form along the GBs. Crystallographic analysis and atomic-scale imaging show that the GB precipitates in both W- and W-Mo-containing HEBs have a cube-on-cube orientation relationship with the matrix. With further strain analysis, the coherency of the precipitate/matrix interface is validated. Nanoindentation tests show that the simultaneous GB segregation and coherent precipitation, as a supplement to the grain hardening, provide additional hardening of the HEBs. Our work provides an in-depth understanding of the GB segregation and precipitation behaviors of HEBs. It suggests that GB engineering could be potentially used for optimizing the performance of high-entropy ceramics.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2025

Improved creep performance of CoCrFeNi high entropy alloys by Mo addition

The CoCrFeNi family of high entropy alloys has good mechanical and corrosion properties, performing like stainless steels with low yield stresses. They could, however, benefit from hardening methods for structural and high temperature applications. Here, this work investigates the potential for the CoCrFeNi alloy to be hardened with the addition of Mo. A series of CoCrFeNiMo alloys and their CoCrFeNi counterparts were subsequently manufactured at NETL and then mechanically creep tested at 650°C. The alloys were designed to possess a range of stacking fault energies which influence the mechanical properties of the alloys via the motion of their dislocations under stress. Results show that Mo-containing variants have creep rupture lives ranging from 4000 to 8000 hours, i.e., about two orders of magnitude longer than those for Mo-free variants. The significantly improved creep performance of the Mo-containing alloys is due to a combination of solid solution strengthening and precipitation strengthening from µ-phase and carbides.

36 MATERIALS SCIENCE↗

DOE OSTI2025

A phase-field fracture formulation for generalized standard materials: The interplay between thermomechanics and damage

Accurately modeling fracture of ductile materials poses open challenges in the field of computational mechanics due to the multiphysics nature of their failure processes. Integrating the interplay between thermodynamics and damage into ductile fracture models is vital for predicting critical failure modes. Here, in this paper, we develop a versatile phase-field (PF) framework for modeling ductile fracture, taking into account finite-strain elasto-plasticity. The framework stems from a variational formulation of constitutive relations for generalized standard materials (GSMs), whose response is described by a Helmholtz free energy and a dissipation pseudo-potential. Its variational structure is based on a minimum principle for a functional that expresses the sum of power densities for reversible and irreversible processes. By minimizing this functional with a constraint on a von Mises yield function, we derive the evolution equation for the equivalent plastic strain and an associative flow rule. This constrained optimization problem is analytically solved for a wide class of thermo-viscoplasticity models. The key innovations of the current work include (i) a cubic plastic degradation function that accounts for a non-vanishing damage-dependent yield stress, (ii) closed-form expressions of the Helmholtz free energy and dissipation pseudo-potential for three thermo-viscoplasticity models, (iii) an extended Johnson–Cook plasticity model with a nonlinear hardening law, and (iv) a plastic work heat source that depends on the plastic degradation function and a variable Taylor–Quinney (TQ) coefficient. The capabilities of the proposed framework are tested with the aid of four ductile fracture problems, including the Sandia Fracture Challenge. In each of these problems, we examine the evolution of relevant field variables such as the PF order parameter, the equivalent plastic strain, the temperature, and the internal power dissipation density, in addition to the overall structural response quantified by the force–displacement curve. These numerical studies demonstrate that the proposed framework effectively represents ductile fracture, yielding computational results that exhibit good agreement with experimental data.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Power Law Hardening Fit for Inconel 718 Material

The objective of this work is to create an accurate elastic-plastic J2 plasticity model calibration for the Inconel 718 material at room temperature for use in finite element models. This calibration was made using a power-law hardening model of form σ = σ y + $Aε^{n}_{p}$ where A and n are empirically determined constants, and σ y is the proportional limit.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Neutron irradiation induced defects and clustering in NF616 and T91

NF616 is a third-generation ferritic martensitic steel, developed to have better creep resistance than the prior generation T91. Unlike relatively numerous studies of T91, there is a lack of understanding of the irradiation effect on the microstructural evolution and mechanical response of NF616. This work evaluated the microstructures and radiation hardening of NF616 irradiated up to 8.2 displacement per atom (dpa) at 292 °C – 431 °C, compared with T91 from two heats. Dislocation loops were observed in all investigated samples. NF616 exhibited comparable loop size but slightly lower loop density than those in the general T91 heat at 430 °C. Cavities were only observed in NF616 at 431 °C but absent at lower irradiation temperatures (292 °C and 359 °C). Ni-rich clusters were also observed in NF616 at 431 °C, while only weak Ni-clustering were observed at lower irradiation temperatures. Compared to the general T91 heat, NF616 demonstrated better swelling resistance (e.g., one third of swelling in the general T91 heat at 430 °C), a slightly higher number density of Ni-rich clusters, and slightly lower radiation hardening. The low-carbon T91 showed the greatest hardening with the largest swelling and loop sizes, despite its lowest irradiation temperature and intermediate dose. The calculated hardening from loops, cavities and Ni-rich clusters using the classic dispersed barrier-hardening model had reasonable agreement with the experiment-derived results, with the primary hardening contribution attributed to dislocation loops.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Nanoindentation Investigation of Chloride-Induced Stress Corrosion Crack Propagation in an Austenitic Stainless Steel Weld

Transgranular chloride-induced stress corrosion cracking (TGCISCC) is a mounting concern for the safety and longevity of arc welds on austenitic stainless steel (AuSS) nuclear waste storage canisters. Recent studies have shown the key role of crystallography in the susceptibility and propagation of TGCISCC in SS weldments. Given that crystallography underlies mechanical heterogeneities, the mechanical-crystallographic relationship during TGCISCC growth must be understood. In this study, welded SS 304L coupons are loaded in four-point bend fixtures and then boiled in magnesium chloride to initiate TGCISCC. Nanoindentation mapping is paired with scanning electron microscopy (SEM) electron backscatter diffraction (EBSD) to understand the correlation between grain orientation, grain boundaries, and hardening from TGCISCC propagation. The nanoindentation hardness of individual grains is found to not be a controlling factor for TGCISCC propagation. However, intragranular hardness is generally highest immediately around the crack due to localized strain hardening at the crack tip. This work shows that nanoindentation techniques can be useful in understanding CISCC behaviors when paired with electron microscopy.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Inclusion of a cold hardening scheme to represent frost tolerance is essential to model realistic plant hydraulics in the Arctic–boreal zone in CLM5.0-FATES-Hydro

As temperatures decrease in autumn, vegetation of temperate and boreal ecosystems increases its tolerance to freezing. This process, known as hardening, results in a set of physiological changes at the molecular level that initiate modifications of cell membrane composition and the synthesis of anti-freeze proteins. Together with the freezing of extracellular water, anti-freeze proteins reduce plant water potentials and xylem conductivity. To represent the responses of vegetation to climate change, land surface schemes increasingly employ “hydrodynamic” models that represent the explicit fluxes of water from soil and through plants. The functioning of such schemes under frozen soil conditions, however, is poorly understood. Nonetheless, hydraulic processes are of major importance in the dynamics of these systems, which can suffer from, e.g., winter “frost drought” events. In this study, we implement a scheme that represents hardening into CLM5.0-FATES-Hydro. FATES-Hydro is a plant hydrodynamics module in FATES, a cohort model of vegetation physiology, growth, and dynamics hosted in CLM5.0. We find that, in frozen systems, it is necessary to introduce reductions in plant water loss associated with hardening to prevent winter desiccation. This work makes it possible to use CLM5.0-FATES-Hydro to model realistic impacts from frost droughts on vegetation growth and photosynthesis, leading to more reliable projections of how northern ecosystems respond to climate change.

58 GEOSCIENCES↗

DOE OSTI2023

Element-Specific Study of Magnetic Anisotropy and Hardening in SmCo 5– x Cu x Thin Films

This work investigates the effect of copper substitution on the magnetic properties of SmCo 5 thin films synthesized by molecular beam epitaxy. A series of thin films with varying concentrations of Cu were grown under otherwise identical conditions to disentangle structural and compositional effects on the magnetic behavior. The combined experimental and theoretical studies show that Cu substitution at the Co 3g sites not only stabilizes the formation of the SmCo 5 structure but also enhances magnetic anisotropy and coercivity. Density functional theory calculations indicate that Sm(Co 4 Cu 3g ) 5 possesses a higher single-ion anisotropy as compared to pure SmCo 5 . In addition, X-ray magnetic circular dichroism reveals that Cu substitution causes an increasing decoupling of the Sm 4f and Co 3d moments. Scanning transmission electron microscopy confirms predominantly SmCo 5 phase formation and reveals nanoscale inhomogeneities in the Cu and Co distribution. Our study based on thin film model systems and advanced characterization as well as modeling reveals novel aspects of the complex interplay of intrinsic and extrinsic contributions to magnetic hysteresis in rare-earth-based magnets, i.e., the combination of increased intrinsic anisotropy due to Cu substitution and the extrinsic effect of inhomogeneous elemental distribution of Cu and Co.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Cyclic Ramberg–Osgood Parameters of 316SS Weld Metal Under In-Air and PWR-Water Environments

We report at present, the available Ramberg–Osgood (R–O) parameters for different metals (e.g., in ASME code and other literatures) are static (generally based on a tensile curve). These static R–O parameters cannot accurately model the cyclic plasticity behavior. This work presents the cyclic R–O material hardening parameters for 316 stainless steel similar metal welds. The parameters were estimated under various conditions (in-air at room temperature, 300 °C in-air, and in-air at primary water conditions for a pressurized water reactor (PWR)). It is anticipated that the reported results would be useful for computational mechanics-based shakedown analysis and fatigue life estimation of PWR components.

42 ENGINEERING↗