Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMPRESSION RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Hot Roll Bonding of Aluminum to Twin-Roll Cast (TRC) Magnesium and Its Subsequent Deformation Behavior

In an experiment in which twin-roll cast AZ31 magnesium alloy and commercial purity aluminum (AA 1050) sheets were bonded by hot rolling as Al/Mg/Al laminate composites, it was found that increasing the preheating temperatures up to 400 °C enhances the bonding strength of composites. Further increases in the preheating temperatures accelerate the magnesium oxide growth and thus reduce the bonding strength. The influence of the reduction ratio on the bonding properties was also studied, whereby it was observed that increasing the rolling reduction led to an increase in the bonding strength. The experimental results show that the optimum bonding strength can be obtained at rolling temperatures of 375-400 °C with a 50-60% reduction in thickness. On the other hand, the subsequent deformation behavior of composite was assessed using plane strain compression and deep drawing tests. We demonstrate that the composites produced using the optimum roll bonding conditions exhibited sufficient bonding during subsequent deformation and did not reveal any debonding at the bonding interface.

36 MATERIALS SCIENCE↗

Mapping local deformation behavior in single cell metal lattice structures

The deformation behavior of metal lattice structures is extremely complex and challenging to predict, especially since strain is not uniformly distributed throughout the structure. Understanding and predicting the failure behavior for these types of light-weighting structures is of great interest due to the excellent scaling of stiffness- and strength-to weight ratios they display. Therefore, there is a need to perform simplified experiments that probe unit cell mechanisms. This study reports on high resolution mapping of the heterogeneous structural response of single unit cells to the macro-scale loading condition. Two types of structures, known to show different stress-strain responses, were evaluated using synchrotron radiation micro-tomography while performing in-situ uniaxial compression tests to capture the local micro-strain deformation. These structures included the octet-truss, a stretch-dominated lattice, and the rhombic-dodecahedron, a bend-dominated lattice. The tomographic analysis showed that the stretch- and bend-dominated lattices exhibit different failure mechanisms and that the defects built into the structure cause a heterogeneous localized deformation response. Also shown here is a change in failure mode for stretch-dominated lattices, where there appears to be a transition from buckling to plastic yielding for samples with a relative density between 10 and 20%. In conclusion, the experimental results were also used to inform computational studies designed to predict the mesoscale deformation behavior of lattice structures. Here an equivalent continuum model and a finite element model were used to predict both local strain fields and mechanical behavior of lattices with different topologies.

36 MATERIALS SCIENCE↗

Identification of crystalline elastic anisotropy in PZT ceramics from in-situ blocking stress measurements

High energy x-ray diffraction measurements of lattice strains were performed on a rhombohedral Lead Zirconate Titanate ceramic (PZT 55-45) under combinations of applied electric field and compressive stress. These measurements allow the construction of blocking stress curves for different sets of crystallographic orientations which reflect the single crystal elastic anisotropy. A micro-mechanical interpretation of the results is then proposed. Assuming cubic symmetry for the crystalline elastic stiffness tensor and isotropy for the macroscopic elastic properties, the elastic properties of the single crystal are extracted from the measured data. An anisotropy ratio close to 0.3 is found (compared to 1 for isotropic materials). The high level of anisotropy found in this work suggests that crystalline elastic anisotropy should not be neglected in the modelling of ferroelectric materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Direct ink write multi-material printing of PDMS-BTO composites with MWCNT electrodes for flexible force sensors

Here, with recent advances of additive manufacturing technology, direct ink write (DIW) printing has allowed to incorporate multi-material printing of various materials with freedom of design and complex geometric shapes to complete functional sensors in a one-step fabrication. This paper introduces the use of DIW 3D printing of polydimethylsiloxane (PDMS) with barium titanate (BTO) filler as stretchable composites with tunable piezoelectric properties that can be used for force sensors applications. To improve the bonding between stretchable piezoelectric composites and electrodes, multi-walled carbon nanotubes was included in the fabrication of electrodes at a fixed ratio of 11 wt. %. The alignment of the BTO dipoles was achieved through corona poling method, which applies an electric charge on the surface layer of the functional material, aligning the dipoles in the desired direction and thus gaining the piezoelectricity. Different BTO mixing ratios (10–50 wt. %) were evaluated in order to obtain tunable piezoelectric properties and compare the sensitivity with respect their elastic properties. Tensile testing and piezoelectric testing were carried out to characterize mechanical and piezoelectric properties. Results showed that fabricated PDMS with 50 wt. % BTO gave the highest piezoelectric coefficient (d 33 ) of 11.5 pC N -1 and with an output voltage of 385 mV under compression loading of >200 lbF. This demonstrates feasibility of using multi-material DIW printing to fabricate piezoelectric force sensors with integrated electrodes in one-step without compromising the flexibility of the material.

36 MATERIALS SCIENCE↗

Alkali-activated Class F Fly Ash-rich Portland Cement Blends as Alternative Thermal Shock Resistant Cements

This study focused on evaluating the resistance of 300°C-autocalved alkali-activing Class F fly ash (FAF)-rich Type II Ordinary Portland Cement (OPC) blends with 80/20 and 90/10 FAF/OPC ratios to five thermal-shock (TS) fatigue cycles (one cycle, 600°C heat – 25°C water quenching). The factors to be evaluated included the hydration behaviors, crystalline/ amorphous phaseidentifications, -compositions and -transformations, and microstructural-developments andalterations for blended cements assembled by three different alkaline activators, sodium metasilicate (SMS), soda ash (SA), and sodium sulfate (SS). All factors were related directory to the changes in compressive strength after TS testing. The setting time of cement slurries at 25° and 85°C depended on the alkaline activators; SMS and SA contributing to a strong alkalinity hastened setting, while SS with moderate alkalinity extended the setting time. A more prolonged setting time was observed from non-activated cement. In this case, there were two separated hydration reactions: The first reaction was the hydration of OPC; the second one was associated with the dissolution and pozzolanic activity of FAF. In contrast, all alkali- activated cements engendered the concomitant hydration of OPC and FAF, thereby conferring a higher compressive strength on them than that of the non-activator one. The principal contributor to the development of strength of both the non-activated and activated cements at 300°C was the amorphous NaO 2 - or CaO-Al 2 O 3 - SiO 2 -H 2 O (N,C-A-S-H) phase formed by the interactions between alkaline activator, OPC, and FAF. This phase played an important role in minimizing the loss in strength after TS. On the other hand, adding SMS and SA introduced the mixed crystalline FAF-OPC hydrates, such as garranite and wairakite, as the major phases, into the autoclaved cement bodies. Also, these activators induced the formation of two FAF-related crystalline hydrates, analcime as the major phase and riversidelite (0.9 nm tobermorite) as the minor one. However, these identified phases were sensitive to TS, so converting the major phases into minor phases or vanishment. In contrast, three crystalline phases including calcite and anhydrous sodium sulfate as the major ones and 1.1 nm tobermorite as the minor one, that formed in non-activated and activated cements remained unchanged after TS. Additionally, SAactivated cement revealed porous microstructure created by the incorporation of copious amount of carbonate reaction products into the cement, raising concerns that cements might enhance the rate of water transportation and reduce compressive strength. Nevertheless, TS-insensitive amorphous N,C-A-S-H phase as the major cementitions structure coexisting with TS-insensitive crystalline products were responsible for sustaining the integrity of alkali-activated FAF-rich OPC cement systems in such harsh heat-cooling fatigue environments.

15 GEOTHERMAL ENERGY↗

Effects of water addition on the combustion of iso -octane investigated in laminar flames, low-temperature reactors, and an HCCI engine

In this work, the effect of H 2 O injection on the combustion process of iso -octane was investigated with the aim to better understand the suitability of water addition as a potential engine control parameter for homogeneous-charge compression ignition (HCCI) combustion. Several experiments were combined including premixed low-pressure flames, a jet-stirred reactor (JSR) and a plug-flow reactor (PFR), both at atmospheric pressure, and a single-cylinder research engine (SCRE) operated with either iso -octane or RON 98 gasoline. The thermal effect of H 2 O addition was determined in laminar premixed iso -octane/O 2 /Ar flames (equivalence ratio $Φ$=1.4, 40 mbar) with H 2 O mole fractions of 0 to 0.22, where water addition reduced the temperature measured by laser-induced fluorescence (LIF) by up to 110 K. Speciation data were obtained from these flames as well as in the JSR ($Φ$=0.65, 933 mbar) and PFR experiments ($Φ$=0.65, 970 mbar) with and without H 2 O addition in the low- to intermediate temperature regime from 700–1100 K. The chemical analysis in these flame and reactor experiments was performed using molecular-beam mass spectrometry (MBMS) employing either electron ionization (EI) in the PFR and premixed flame or single-photon ionization (PI) by tunable vacuum-ultraviolet radiation in the JSR. The effects on species mole fractions were small which is supported by predictions from chemical-kinetic simulations. Quantitative speciation data of the exhaust gas of the SCRE were obtained by using Fourier-transform infrared (FTIR) spectroscopy. A very similar species pool was detected in the laboratory-scale experiments and for the engine operation. It is thus assumed that these results could assist in guiding both the improvement of fundamental chemical-kinetic as well as HCCI engine control models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Phase transitions in MgSiO 3 post-perovskite in super-Earth mantles

The highest pressure form of the major Earth-forming mantle silicate is MgSiO 3 post-perovskite (PPv). Understanding the fate of PPv at TPa pressures is the first step for understanding the mineralogy of super-Earths-type exoplanets, arguably the most interesting for their similarities with Earth. Modeling their internal structure requires knowledge of stable mineral phases, their properties under compression, and major element abundances. Several studies of PPv under extreme pressures support the notion that a sequence of pressure induced dissociation transitions produce the elementary oxides SiO 2 and MgO as the ultimate aggregation form at ~3 TPa. However, none of these studies have addressed the problem of mantle composition, particularly major element abundances usually expressed in terms of three main variables, the Mg/Si and Fe/Si ratios and the Mg#, as in the Earth. Here we show that the critical compositional parameter, the Mg/Si ratio, whose value in the Earth’s mantle is still debated, is a vital ingredient for modeling phase transitions and internal structure of super-Earth mantles. Specifically, we have identified new sequences of phase transformations, including new recombination reactions that depend decisively on this ratio. This is a new level of complexity that has not been previously addressed, but proves essential for modeling the nature and number of internal layers in these rocky mantles.

58 GEOSCIENCES↗

High-strength, lightweight nano-architected silica

Continuous nanolattices are an emerging class of mechanical metamaterials that are highly attractive due to their superior strength-to-weight ratios, which originate from their spatial architectures and nanoscale-sized elements possessing near-theoretical strength. Rational design of frameworks remains challenging below 50 nm because of limited methods to arrange small elements into complex architectures. Here, we fabricate silica frameworks with ~4- to 20-nm-thick elements using self-assembly and silica templating of DNA origami nanolattices and perform in situ micro-compression testing to examine the mechanical properties. We observe strong effects of lattice dimensions on yield strength (σ $\mathcal{y}$ ) and failure mode. Silica nanolattices are found to exhibit yield strengths higher than those of any known engineering materials with similar mass density. The robust coordination of the nanothin and strong silica elements leads to the combination of lightweight and high-strength framework materials offering an effective strategy for the fabrication of nanoarchitected materials with superior mechanical properties.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Single-pulse (100 ps) extended x-ray absorption fine structure capability at the Dynamic Compression Sector

Determining real-time changes in the local atomistic order is important for a mechanistic understanding of shock wave induced structural and chemical changes. However, the single event and short duration (nanosecond times) nature of shock experiments pose challenges in obtaining Extended X-ray Absorption Fine Structure (EXAFS) measurements - typically used for monitoring local order changes. Here, we report on a new single pulse (~100 ps duration) transmission geometry EXAFS capability for use in laser shock-compression experiments at the Dynamic Compression Sector (DCS), Advanced Photon Source. We used a flat plate of highly oriented pyrolytic graphite (HOPG) as the spectrometer element to energy disperse x-rays transmitted through the sample. It provided high efficiency with approximately 15% of the x-rays incident on the HOPG reaching an x-ray area detector with high quantum efficiency. This combination resulted in good signal-to-noise ratio (~10 3 ), energy resolution of ~10 eV at 10 keV, EXAFS spectra covering 100s of eV, and good pulse to pulse reproducibility of our single pulse measurements. Ambient EXAFS spectra for Cu and Au are compared to reference spectra, validating our measurement system. Comparison of single pulse EXAFS results for ambient and laser shocked Ge(100) shows large changes to the local structure of the short lived state of shocked Ge. The current DCS EXAFS capability can be used to perform single pulse measurements in laser shocked materials from approximately 9-13 keV. These EXAFS developments will be available to all users of the DCS.

47 OTHER INSTRUMENTATION↗

Low Temperature Combustion with Thermo-Chemical Recuperation to Maximize In-Use Engine Efficiency

The key to overcome Low Temperature Combustion (LTC) load range limitations in reciprocating engines is based on proper control over the thermo-chemical properties of the in-cylinder charge. The studied alternative to achieve the required control of LTC is the use of two separate fuel streams to regulate timing and heat release at specific operational points, where the secondary fuel is a reformed product of the primary fuel in the tank. It is proposed in this report that the secondary fuel can be produced using exhaust heat and Thermo-Chemical Recuperation (TCR). TCR for reciprocating engines is a system that employs high efficiency recovery of sensible heat from engine exhaust gas and uses this energy to transform fuel composition. The recuperated sensible heat is returned to the engine as chemical energy. Chemical conversions are accomplished through catalytic and endothermic reactions in a specially designed reforming reactor. An equilibrium model developed by Gas Technology Institute (GTI) for heptane steam reforming was applied to estimate reformed fuel composition at different reforming temperatures. Laboratory results, at a steam/heptane mole ratio less than 2:1, confirm that low temperature reforming reactions, in the range of 550 K to 650 K, can produce 10-30% hydrogen (by volume, wet) in the product stream. Also, the effect of trading low mean effective pressure for displacement to achieve power output and energy efficiency has been explored by WVU. A zerodimensional model of LTC using heptane as fuel and a diesel Compression Ignition (CI) combustion model were employed to estimate pressure, temperature and total heat release as inputs for a mechanical and thermal loss model. The model results show that the total cooling burden on an LTC engine with lower power density and higher displacement was 14.3% lower than the diesel engine for the same amount of energy addition in the case of high load (43.57mg fuel/cycle). These preliminary modeling and experimental results suggest that the LTC-TCR combination may offer a high efficiency solution to engine operation. A single zone model using a detailed chemical kinetic mechanism was implemented in CHEMKIN and to study the effects of base fuel and steam-fuel reforming products on the ignition timing and heat release characteristics. The study was performed considering the reformed fuel species composition for total n-heptane conversion (ideal case) and also at the composition corresponding to a specific set of operational reforming temperatures (real case). The computational model confirmed that the reformed products have a strong influence on the low temperature heat release (LTHR) region, affecting the onset of the high temperature heat release (HTHR). The ignition timing was proportionally delayed with respect to the baseline fuel case when higher concentrations of reformed gas were used. For stoichiometric concentration of RG, it was found that by increasing the proportion of reformed fuel to total fuel (RG), from 0% to 30%, the amount of energy released during the LTHR regime, or HR L , was reduced by 48% and the ignition timing was delayed 10.4 CA degrees with respect to the baseline fuel case. For RG composition corresponding to certain operational reforming temperatures, it was found that the most significant effects on the HCCI combustion, regarding HR L reduction and CA50 delay, was obtained by RG produced at a reforming temperature range of 675 K-725 K.

10 SYNTHETIC FUELS↗

Development of Multi-Filament Textured-Powder Bi-2212/Ag Wire with Enhanced Local Area Ratio (Final Technical Report)

ATC has successfully developed a new method for making high-performance Bi-2212/Ag su-perconducting wire with a favorable local area ratio (LAR)=Ag:Bi-2212. The method begins by texturing a fine powder of Bi-2212: the powder is loaded uniformly into an open-sided silver foil channel, the flaps of foil are folded over the powder filling, and the package is hydraulically com-pressed in a die set to form a textured-powder (TP) bar. XRD analysis of the interior powder in a compressed bar shows a texture of 80% after 200 MPa compression.

36 MATERIALS SCIENCE↗

Elastically-homogeneous lattice models of damage in geomaterials

This paper involves the development of the auxiliary stress approach for producing elastically-homogeneous lattice models of damage in geomaterials. The lattice models are based on random, three-dimensional assemblages of rigid-body-spring elements. Unlike conventional lattice or particle models, the elastic constants of a material (e.g., Young’s modulus and Poisson’s ratio) are represented properly in both global and local senses, without any need for calibration. The proposed approach is demonstrated and validated through analyses of homogeneous and heterogeneous systems under uni- and tri-axial loading conditions. Comparisons are made with analytical solutions and finite element results. Thereafter, the model is used to simulate a series of standard laboratory tests: (a) split-cylinder tests, and (b) uniaxial compressive tests of sedimentary rocks at the Horonobe Underground Research Laboratory in Hokkaido, Japan. Model inputs are based on physical quantities measured in the experiments. Finally, the simulation results agree well with the experimental results in terms of pre-peak stress-strain/displacement responses, strength measurements, and failure patterns.

3D irregular lattice↗

An experimental and modeling study on autoignition of 2-phenylethanol and its blends with n-heptane

2-Phenylethanol (2-PE) is an aromatic alcohol with high research octane number, high octane sensitivity, and a potential to be produced using biomass. Considering that 2-PE can be used as a fuel additive for boosting the anti-knocking quality of gasoline in spark-ignition engines and as the low reactivity fuel or fuel component in dual-fuel reactivity controlled compression ignition (RCCI) engines, it is of fundamental and practical interest to understand the autoignition chemistry of 2-PE, especially at low-to-intermediate temperatures (<1000 K). Based upon the experimental ignition delay time (IDT) results of neat 2-PE obtained from our previous rapid compression machine (RCM) investigation and the literature shock tube study, a detailed chemical kinetic model of 2-PE is developed herein, covering low-to-high temperature regimes. Besides, RCM experiments using binary fuel blends of 2-PE and n-heptane (nC7) are conducted in this work to investigate the nC7/2-PE blending effects, as they represent a dual-fuel system for RCCI operations. Furthermore, the newly developed 2-PE model is merged with a well-validated nC7 kinetic model to generate the current nC7/2-PE binary blend model. Overall, the consolidated model reasonably predicts the experimental IDT data of neat 2-PE and nC7/2-PE blends, as well as captures the experimental effects of pressure, equivalence ratio, and blending ratio on autoignition. Finally, model-based chemical kinetic analyses are carried out to understand and identify the controlling chemistry accounting for the observed blending effects in RCM experiments. In conclusion, the analyses reveal that nC7 enhances 2-PE autoignition via providing extra $\dot{O}$H radicals to the shared radical pool, while the diminished nC7 promoting effect on 2-PE autoignition with increasing temperature is due to the negative temperature coefficient characteristics of nC7.

2-phenlyethanol↗

Formation of magnesium silicate hydrate (M-S-H) cement pastes using sodium hexametaphosphate

Magnesium silicate hydrate (M-S-H) gel is formed by the reaction of brucite with amorphous silica during sulphate attack in concrete and M-S-H is therefore regarded as having limited cementing properties. The aim of this work was to form M-S-H pastes, characterise the hydration reactions and assess the resulting properties. It is shown that M-S-H pastes can be prepared by reacting magnesium oxide (MgO) and silica fume (SF) at low water to solid ratio using sodium hexametaphosphate (NaHMP) as a dispersant. Characterisation of the hydration reactions by x-ray diffraction and thermogravimetric analysis shows that brucite and M-S-H gel are formed and that for samples containing 60 wt.% SF and 40 wt.% MgO all of the brucites react with SF to form M-S-H gel. These M-S-H cement pastes were found to have compressive strengths in excess of 70 MPa.

36 MATERIALS SCIENCE↗

Rate-dependent deformation and Poisson’s effect in porous titanium

Dynamic and quasi-static compression experiments are conducted on a high-density porous titanium with in situ X-ray imaging to characterize its deformation dynamics. The porous titanium exhibits higher strain-rate sensitivity than full-density titanium. Strain field mapping indicates that compaction bands are narrower and denser under dynamic loading, leading to a more homogeneous strain distribution and thus a higher flow stress. Here, the mean Poisson's ratio for dynamic loading is 15% lower than that for quasi-static loading at the same bulk strain, as a result of local inertial confinement which also contributes to the rate hardening of porous titanium.

36 MATERIALS SCIENCE↗

MICROSCOPIC DYNAMICS AT THE GLASS TRANSITION: INSIGHTS FROM SOFT COLLOIDAL DISPERSIONS

We investigate the microscopic dynamics of compressible colloidal particles as function of concentration through dynamic light scattering and confocal microscopy experiments. In analogy with hard sphere (HS) colloidal systems, we find that the particles display liquid, supercooled liquid or glassy dynamics, depending on volume fraction. In the present case, however caging effects are observed for particle volume fractions higher than one, i.e. when the particles are compressed. We find that heterogeneous dynamics, described by a non Gaussian distribution of the displacements, play a major role in the supercooled liquid in proximity of the relaxation time.

36 MATERIALS SCIENCE↗

Electron scattering in graphene with adsorbed NaCl nanoparticles

In this work, the results of contactless magnetoconductance and Raman spectroscopy measurements performed for a graphene sample after its immersion in NaCl solution were presented. The properties of the immersed sample were compared with those of a non-immersed reference sample. Atomic force microscopy and electron spin resonance experiments confirmed the deposition of NaCl nanoparticles on the graphene surface. A weak localization signal observed using contactless magnetoconductance showed the reduction of the coherence length after NaCl treatment of graphene. Temperature dependence of the coherence length indicated a change from ballistic to diffusive regime in electron transport after NaCl treatment. The main inelastic scattering process was of the electron-electron type but the major reason for the reduction of the coherence length at low temperatures was additional, temperature independent, inelastic scattering. We associate it with spin flip scattering, caused by NaCl nanoparticles present on the graphene surface. Raman spectroscopy showed an increase in the D and D′ bands intensities for graphene after its immersion in NaCl solution. An analysis of the D, D′, and G bands intensities proved that this additional scattering is related to the decoration of vacancies and grain boundaries with NaCl nanoparticles, as well as generation of new on-site defects as a result of the decoration of the graphene surface with NaCl nanoparticles. The observed energy shifts of 2D and G bands indicated that NaCl deposition on the graphene surface did not change carrier concentration, but reduced compressive biaxial strain in the graphene layer.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Carbon distribution in bainitic steel subjected to deformation

Analysis of the formation and evolution of carbide phase in medium carbon steel with a bainitic structure during compressive deformation was performed by means of transmission electron diffraction microscopy. Qualitative transformations in carbide phase medium size particles, their density and volume concentration depended on the degree of deformation.

36 MATERIALS SCIENCE↗