Search NASA⌕ Search

SEARCH · Search NASA

Results for “compression ignition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Investigating anode off-gas under spark-ignition combustion for SOFC-ICE hybrid systems

Solid oxide fuel cell – internal combustion engine (SOFC-ICE) hybrid systems are an attractive solution for electricity generation. The system can achieve up to 70% theoretical electric power conversion efficiency through energy cascading enabled by utilizing the anode off-gas from the SOFC as the fuel source for the ICE. Experimental investigations were conducted with a single cylinder Cooperative Fuel Research (CFR) engine by altering fuel-air equivalence ratio (φ), and compression ratio (CR) to study the engine load, combustion characteristics, and emissions levels of dry SOFC anode off-gas consisting of 33.9% H 2 , 15.6% CO, and 50.5% CO 2 . The combustion efficiency of the anode off-gas was directly evaluated by measuring the engine-out CO emissions. The highest net-indicated fuel conversion efficiency of 31.3% occurred at φ = 0.90 and CR = 13:1. These results demonstrate that the anode off-gas can be successfully oxidized using a spark ignition combustion mode. The fuel conversion efficiency of the anode tail gas is expected to further increase in a more modern engine architecture that can achieve increased burn rates in comparison to the CFR engine. NO x emissions from the combustion of anode off-gas were minimal as the cylinder peak temperatures never exceeded 1800 K. This experimental study ultimately demonstrates the viability of an ICE to operate using an anode off-gas, thus creating a complementary role for an ICE to be paired with a SOFC in a hybrid power generation plant.

Engineering↗

Fiber-Optic Determination of N2, O2, and Fuel Vapor in the Ullage of Liquid-Fuel Tanks

A fiber-optic sensor system has been developed that can remotely measure the concentration of molecular oxygen (O2), nitrogen (N2), hydrocarbon vapor, and other gases (CO2, CO, H2O, chlorofluorocarbons, etc.) in the ullage of a liquid-fuel tank. The system provides an accurate and quantitative identification of the above gases with an accuracy of better than 1 percent by volume (for O2 or N2) in real-time (5 seconds). In an effort to prevent aircraft fuel tank fires or explosions similar to the tragic TWA Flight 800 explosion in 1996, OBIGGS are currently being developed for large commercial aircraft to prevent dangerous conditions from forming inside fuel tanks by providing an inerting gas blanket that is low in oxygen, thus preventing the ignition of the fuel/air mixture in the ullage. OBIGGS have been used in military aircraft for many years and are now standard equipment on some newer large commercial aircraft (such as the Boeing 787). Currently, OBIGGS are being developed for retrofitting to existing commercial aircraft fleets in response to pending mandates from the FAA. Most OBIGGS use an air separation module (ASM) that separates O2 from N2 to make nitrogen-enriched air from compressed air flow diverted from the engine (bleed air). Current OBIGGS systems do not have a closed-loop feedback control, in part, due to the lack of suitable process sensors that can reliably measure N2 or O2 and at the same time, do not constitute an inherent source of ignition. Thus, current OBIGGS operate with a high factor-of-safety dictated by process protocol to ensure adequate fuel-tank inerting. This approach is inherently inefficient as it consumes more engine bleed air than is necessary compared to a closed-loop controlled approach. The reduction of bleed air usage is important as it reduces fuel consumption, which translates to both increased flight range and lower operational costs. Numerous approaches to developing OBIGGS feedback-control sensors have been under development by many research groups and companies. However, the direct measurement of nitrogen (N2) is a challenge to most OBIGGS ullage sensors (such as tunable diode laser absorption) as they cannot measure N2 directly but depend on the measurement of oxygen (O2). The problem with a singular measure of O2, is that as the concentration (number density) of O2 decreases due to the inerting process or due to lower pressures from high altitudes, the precision and accuracy of the O2 measurement decreases. However, measuring O2 density in combination with N2 density (which is more abundant in air and in a N2-inerted fuel tank) can provide a much more accurate and reliable determination of the OBIGGS efficacy.

Nguyen, Quang-Viet↗

High BMEP and High Efficiency Micro-Pilot Ignition Natural Gas Engine (Final Project Report)

The project objectives were to develop demonstrate a high-efficiency high-output natural gas diesel micro-pilot stoichiometric engine operating with diesel pilot contribution of less than 5% on a medium duty engine. The program’s outcomes achieve in a partnership between Michigan Technological University and Westport Power Inc. were very successful. The engine platform was a 6.7L I6 engine with a compression ratio of 15:1 and achieved 24 bar BMEP and 41% brake thermal efficiency at lambda. Simulation and modeling with an improved turbocharger and combustion chamber improvements demonstrated a clear path to 43% BTE. The operational stoichiometric range was from 5 to 24 bar with minimal throttling. Diesel contribution over the cycle was 4.6%. The results achieved in this program are well above the best in-class baseline natural gas spark ignition engines of 19.5 bar BMEP and 40% BTE.

33 ADVANCED PROPULSION SYSTEMS↗

Cryogenic tritium-hydrogen-deuterium and deuterium-tritium layer implosions with high density carbon ablators in near-vacuum hohlraums

High Density Carbon (or diamond) is a promising ablator material for use in near-vacuum hohlraums, as its high density allows for ignition designs with laser pulse durations of <10 ns. A series of Inertial Confinement Fusion (ICF) experiments in 2013 on the National Ignition Facility [Moses et al., Phys. Plasmas 16, 041006 (2009)] culminated in a deuterium-tritium (DT) layered implosion driven by a 6.8 ns, 2-shock laser pulse. This paper describes these experiments and comparisons with ICF design code simulations. Backlit radiography of a tritium-hydrogen-deuterium (THD) layered capsule demonstrated an ablator implosion velocity of 385 km/s with a slightly oblate hot spot shape. Other diagnostics suggested an asymmetric compressed fuel layer. A streak camera-based hot spot self-emission diagnostic (SPIDER) showed a double-peaked history of the capsule self-emission. Simulations suggest that this is a signature of low quality hot spot formation. Changes to the laser pulse and pointing for a subsequent DT implosion resulted in a higher temperature, prolate hot spot and a thermonuclear yield of 1.8 × 10{sup 15} neutrons, 40% of the 1D simulated yield.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Novel fabrication tools for dynamic compression targets with engineered voids using photolithography methods

Mesoscale imperfections, such as pores and voids, can strongly modify the properties and the mechanical response of materials under extreme conditions. Tracking the material response and microstructure evolution during void collapse is crucial for understanding its performance. In particular, imperfections in the ablator materials, such as voids, can limit the efficiency of the fusion reaction and ultimately hinder ignition. To characterize how voids influence the response of materials during dynamic loading and seed hydrodynamic instabilities, we, in this paper, have developed a tailored fabrication procedure for designer targets with voids at specific locations. Our procedure uses SU-8 as a proxy for the ablator materials and hollow silica microspheres as a proxy for voids and pores. By using photolithography to design the targets’ geometry, we demonstrate precise and highly reproducible placement of a single void within the sample, which is key for a detailed understanding of its behavior under shock compression. This fabrication technique will benefit high-repetition rate experiments at x-ray and laser facilities. Insight from shock compression experiments will provide benchmarks for the next generation of microphysics modeling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of nitric oxide and exhaust gases on gasoline surrogate autoignition: iso-octane experiments and modeling

Exhaust gas recirculation (EGR) is widely used in advanced internal combustion engines to reduce engine emissions as well as control combustion phasing. Among various species present in EGR gases, CO 2 and H 2 O are two major components that can thermally and chemically affect fuel autoignition. It is of fundamental interest to isolate the thermal and chemical effects of CO 2 and H 2 O on fuel autoignition, especially as such an effort has not been reported in the literature. Moreover, nitric oxide (NO) is known to exhibit strong chemical effects on fuel autoignition, which in turn affects engine combustion phasing. The effects of ultra-low NO addition (< 100 ppm) on fuel autoignition at low temperatures are also not well understood. Recognizing these problems, autoignition experiments of iso-octane (a major gasoline surrogate component) in air are performed in this study using a rapid compression machine at varying compressed pressures, equivalence ratios, dilution levels with an EGR gas analogue (consisting of CO 2 , H 2 O, O 2 , and N 2 ) and N 2 only, and varying amounts of NO addition. Furthermore, the thermal and chemical effects of the EGR gas analogue are isolated and evaluated by comparing the ignition delay time datasets of EGR and N2-only diluted cases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chemical kinetic interactions and sensitivity analyses for 2-ethylhexyl nitrate-doped PRF91 using a reduced mechanism

A numerical and experimental investigation about the chemical kinetic interactions between 2-ethylhexylnitrate (EHN) and PRF91 was performed in this study. Rapid compression machine experiments were conducted to investigate the effect of EHN on the autoignition reactivity of the fuel, and a reduced chemical kinetic mechanism was developed including an EHN sub-model. Experiments showed that the ignition delay decreases as the fuel is doped with EHN, but the effect of the doping level of EHN on the ignition is highly non-linear. Moreover, experiments showed that the EHN effectiveness is lowest during the transition between the low-temperature regime and the negative temperature coefficient (NTC) regime, and it rapidly increases as the temperature increases. Both detailed and (developed) reduced mechanisms were validated against the experimental results, allowing a more in-depth EHN-fuel chemistry study. Additionally, ignition delay sensitivity and EHN effectiveness sensitivity analyses were performed with the reduced mechanism to identify the reactions that control the interaction between EHN and the fuel. As the result, EHN thermal decomposition is only relevant for very low temperatures. The chemistry of EHN-doped fuel is more sensitive to intermediate temperature reactions than that of straight fuel, especially at lower temperatures, due to the effect of EHN on the NTC behavior of the fuel. Finally, the chemistry of EHN-doped fuel is very sensitive to NO 2 -to-NO reactions, especially at high temperatures, because these reactions transform the NO 2 generated by EHN into NO, which is a very effective fuel reactivity enhancer.

2-ethylhexyl nitrate↗

Inertial Confinement Fusion—Experimental Physics: Laser Drive

Laser-driven inertial confinement fusion creates a central hot-spot plasma by irradiating a spherical target containing a thermonuclear fuel layer of deuterium (D) and tritium (T) with temporally-shaped, high-intensity lasers or X rays. Inertial confinement fusion relies on the DT-fusion alpha particles depositing their energy in a hot-spot plasma, causing its temperature to rise sharply and a thermonuclear burn wave to propagate out through the surrounding cold, dense DT fuel, producing significantly more energy than was used to heat and compress the fuel. Alpha heating has been demonstrated and burning plasma (i.e., yield amplification due to alpha heating >3.5) is being explored with megajoule-scale lasers on the path to ignition (i.e., yield amplification due to alpha heating >20)

alpha particles↗

Autoignition of n-decane under elevated pressure and low-to-intermediate temperature conditions

An experimental investigation of the autoignition for various n-decane/oxidizer mixtures is conducted using a rapid compression machine, in the range of equivalence ratios of {phi}=0.5-2.2, dilution molar ratios of N{sub 2}/(O{sub 2} + N{sub 2}) = 0.79-0.95, compressed gas pressures of P{sub C}=7-30 bar, and compressed gas temperatures of T{sub C}=635-770 K. The current experiments span a temperature range not fully investigated in previous autoignition studies on n-decane. Two-stage ignition, characteristic of large hydrocarbons, is observed over the entire range of conditions investigated, as demonstrated in the plots of raw experimental pressure traces. In addition, experimental results reveal the sensitivity of the first-stage and total ignition delays to variations in fuel and oxygen mole fractions, pressure, and temperature. Predictability of two kinetic mechanisms is compared against the present data. Discrepancies are noted and discussed, which are of direct relevance for further improvement of kinetic models of n-decane at conditions of elevated pressures and low-to-intermediate temperatures. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ramp-release experiments for strength measurements: Strain-rate dependence

This paper presents an enhanced analysis method for investigating material properties at high strain rates, extending the capability of established experimental techniques to gain more information. The ramp-release method has been applied to many experiments reported at high (≈10 5 − 10 6 s −1 ) strain-rates. More recent data gathered at the National Ignition Facility (NIF) has enabled higher (≈10 8 s −1 ) strain-rates to be studied. Here, we present an initial application of ramp-release analysis to NIF ramp-compression data, illustrating both the opportunities and the practical challenges of extending these methods to laser-driven platforms. The higher strain-rates accessed at the NIF mean that there is more strain-rate enhancement to strength, and the experimental configuration means that this enhancement is more readily seen in the data. This is enabled by the capability of avoiding peak-compression attenuation through the sample thickness with a designed hold period made possible by the pulse-shaping capability of NIF. We propose that this combination of experimental conditions and an enhanced analysis method enables the strain-rate enhancement to strength to be studied, and potentially for this to inform physics models at smaller scales than the continuum.

36 MATERIALS SCIENCE↗

Milestone report for MRT 8504: Commission EXAFS spectrometer with spectral range of 17.95-18.6 keV design to obtain EXAFS data for Pu L shell experiments

This milestone describes the development and fielding of EXAFS Phase II spectrometer designed to provide high quality (SNR>=5) EXAFS spectra for Plutonium measurements at the National Ignition facility (NIF). Benefits: the EXAFS data will be used by the High Energy Density (HED) Physics and more specifically the Focused Material Science program to measure the thermal state of compressed materials with good temperature sensitivity (~100-1000 Kelvin). Data with good signal to noise ratio (SNR>=5) and good spectral resolution allows the FMS program to fill a gap in diagnosing temperature to completely constrain material properties for weapon physics and Stockpile Stewardship applications.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Risks of Depress as a Fire Suppression Technique in Spacecraft

Spacecraft are designed to prevent fires through careful material selection and configuration control combined with electrical design controls and isolation of ignition sources. Despite these best efforts, fire risk still exists due to the potential for configuration changes with the introduction of crew and the potential for a ‘failure of imagination’ by designers in anticipating all fuel and ignition sources. Therefore, fire suppression is a critical capability for any crewed spacecraft as a last resort for crew survival. Many spacecraft suppression methods have relied on fire suppressants such as compressed carbon dioxide, nitrogen, and water. A proposed alternative is depressurization of the cabin as a method to extinguish a fire. Limited testing was conducted during Skylab and showed that depress could result in stirring the air flow and aggravating a fire before extinguishing. However, limited information was available on how the test was conducted. To better characterize the approach, testing was conducted at NASA’s White Sands Test Facility to evaluate the effect of depressurization on material extinguishment. The results showed that depressurization does not provide a safe and effective fire suppression capability. The testing approach, results, and conclusions are described and discussed.

Toni Griego↗

Deflagration Wave Profiles

Shock initiation in a plastic-bonded explosives (PBX) is due to hot spots. Current reactive burn models are based, at least heuristically, on the ignition and growth concept. The ignition phase occurs when a small localized region of high temperature (or hot spot) burns on a fast time scale. This is followed by a growth phase in which a reactive front spreads out from the hot spot. Propagating reactive fronts are deflagration waves. A key question is the deflagration speed in a PBX compressed and heated by a shock wave that generated the hot spot. Here, the ODEs for a steady deflagration wave profile in a compressible fluid are derived, along with the needed thermodynamic quantities of realistic equations of state corresponding to the reactants and products of a PBX. The properties of the wave profile equations are analyzed and an algorithm is derived for computing the deflagration speed. As an illustrative example, the algorithm is applied to compute the deflagration speed in shock compressed PBX 9501 as a function of shock pressure. The calculated deflagration speed, even at the CJ pressure, is low compared to the detonation speed. The implication of this are briefly discussed.

36 MATERIALS SCIENCE↗

60 years of science in ICF: from conception to scientific breakeven on the National Ignition Facility

The recent achievements of a burning plasma, fusion ignition, and scientific energy gain with deuterium-tritium (DT) fuel at Lawrence Livermore National Laboratory’s National Ignition Facility (NIF) represents a major milestone in the development of inertial confinement fusion (ICF) and all of fusion research. In these experiments, fuel pressures well in excess of hundreds of GBars were achieved in the compressed fuel, and robust alpha heating of the fuel, far in excess of the energy provided by the implosion, were demonstrated for the first time. These achievements occurred 60 years after the inception of ICF and the first laser demonstration, and were made possible by more than five decades of research at laser facilities around the world. Advances in laser technology both in wavelength and precision, motivated by improved understanding of laser-plasma interaction physics and the demands of targets; improvements in target fabrication inspired by the need to control and minimize hydrodynamic instabilities in the implosion; and multi-dimensional simulations and diagnostics have been critical to this achievement. This paper will summarize the scientific and technical advances, the surprises, and the challenges that had to be overcome to achieve these goals.

fusion↗

Temperature separation under compression of moderately coupled plasma

In moderately coupled plasmas, a significant fraction of the internal energy resides in electric fields. As these plasmas are heated or compressed, the shifting partition of energy between particles and fields leads to surprising effects, particularly when ions and electrons have different temperatures. In this work, quasi-equations of state (quasi-EOS) are derived for two-temperature moderately coupled plasma in a thermodynamic framework and expressed in a simple form. These quasi-EOS readily yield expressions for correlation heating, in which heating of the electrons causes a rapid increase in ion temperature even in the absence of collisional energy exchange between species. It is also shown that, remarkably, compression of moderately coupled plasma drives a temperature difference between electrons and ions, even when the species start at equal temperatures. These additional channels for ion heating may be relevant in designing ignition schemes for inertial confinement fusion.

Fetsch, H. (ORCID:0000000256133975)↗

Fast-ignition transport studies: Realistic electron source, integrated particle-in-cell and hydrodynamic modeling, imposed magnetic fields

Transport modeling of idealized, cone-guided fast ignition targets indicates the severe challenge posed by fast-electron source divergence. The hybrid particle-in-cell (PIC) code Zuma is run in tandem with the radiation-hydrodynamics code Hydra to model fast-electron propagation, fuel heating, and thermonuclear burn. The fast electron source is based on a 3D explicit-PIC laser-plasma simulation with the PSC code. This shows a quasi two-temperature energy spectrum and a divergent angle spectrum (average velocity-space polar angle of 52 Degree-Sign ). Transport simulations with the PIC-based divergence do not ignite for >1 MJ of fast-electron energy, for a modest (70 {mu}m) standoff distance from fast-electron injection to the dense fuel. However, artificially collimating the source gives an ignition energy of 132 kJ. To mitigate the divergence, we consider imposed axial magnetic fields. Uniform fields {approx}50 MG are sufficient to recover the artificially collimated ignition energy. Experiments at the Omega laser facility have generated fields of this magnitude by imploding a capsule in seed fields of 50-100 kG. Such imploded fields will likely be more compressed in the transport region than in the laser absorption region. When fast electrons encounter increasing field strength, magnetic mirroring can reflect a substantial fraction of them and reduce coupling to the fuel. A hollow magnetic pipe, which peaks at a finite radius, is presented as one field configuration which circumvents mirroring.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Monte Carlo N-Particle forward modeling for density reconstruction of double shell capsule radiographs

In the Double Shell Inertial Confinement Fusion concept, characterizing the shape asymmetry of imploding metal shells is vital for understanding energy-efficient compression and radiative losses of the thermonuclear fuel. The Monte Carlo N-Particle MCNP® code forward models radiography of Double Shell capsule implosions using the Advanced Radiographic Capability at the National Ignition Facility. A procedure is developed for using MCNP to reconstruct density profiles from the radiograph image intensity. For a given Double Shell imploding target geometry, MCNP radiographs predict image contrast, which can help guide experimental design. Finally, in future work, the calculated MCNP synthetic radiographs will be compared with experimental radiographs to determine the radial and azimuthal density profiles of the Double Shell capsules.

47 OTHER INSTRUMENTATION↗

Design and modeling of indirectly driven magnetized implosions on the NIF

The use of magnetic fields to improve the performance of hohlraum-driven implosions on the National Ignition Facility (NIF) is discussed. The focus is on magnetically insulated inertial confinement fusion, where the primary field effect is to reduce electron-thermal and alpha-particle loss from the compressed hotspot (magnetic pressure is of secondary importance). We summarize the requirements to achieve this state. The design of recent NIF magnetized hohlraum experiments is presented. These are close to earlier shots in the three-shock, high-adiabat (BigFoot) campaign, subject to the constraints that magnetized NIF targets must be fielded at room-temperature, and use ≲1 MJ of laser energy to avoid the risk of optics damage from stimulated Brillouin scattering. We present results from the original magnetized hohlraum platform, as well as a later variant that gives a higher hotspot temperature. In both platforms, imposed fields (at the capsule center) of up to 28 T increase the fusion yield and hotspot temperature. Integrated radiation-magneto-hydrodynamic modeling with the Lasnex code of these shots is shown, where laser power multipliers and a saturation clamp on cross-beam energy transfer are developed to match the time of peak capsule emission and the P2 Legendre moment of the hotspot x-ray image. The resulting fusion yield and ion temperature agree decently with the measured relative effects of the field, although the absolute simulated yields are higher than the data by 2.0−2.7×. The tuned parameters and yield discrepancy are comparable for experiments with and without an imposed field, indicating the model adequately captures the field effects. Self-generated and imposed fields are added sequentially to simulations of one BigFoot NIF shot to understand how they alter target dynamics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗