Search NASA⌕ Search

SEARCH · Search NASA

Results for “geometry optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

FEM design and simulation of a short, 10 MV, S-band Linac with Monte Carlo dose simulations

Purpose: Current commercial 10 MV Linac waveguides are 1.5 m. The authors’ current 6 MV linear accelerator–magnetic resonance imager (Linac–MR) system fits in typical radiotherapy vaults. To allow 10 MV treatments with the Linac–MR and still fit within typical vaults, the authors design a 10 MV Linac with an accelerator waveguide of the same length (27.5 cm) as current 6 MV Linacs. Methods: The first design stage is to design a cavity such that a specific experimental measurement for breakdown is applicable to the cavity. This is accomplished through the use of finite element method (FEM) simulations to match published shunt impedance, Q factor, and ratio of peak to mean-axial electric field strength from an electric breakdown study. A full waveguide is then designed and tuned in FEM simulations based on this cavity design. Electron trajectories are computed through the resulting radio frequency fields, and the waveguide geometry is modified by shifting the first coupling cavity in order to optimize the electron beam properties until the energy spread and mean energy closely match values published for an emulated 10 MV Linac. Finally, Monte Carlo dose simulations are used to compare the resulting photon beam depth dose profile and penumbra with that produced by the emulated 10 MV Linac. Results: The shunt impedance, Q factor, and ratio of peak to mean-axial electric field strength are all matched to within 0.1%. A first coupling cavity shift of 1.45 mm produces an energy spectrum width of 0.347 MeV, very close to the published value for the emulated 10 MV of 0.315 MeV, and a mean energy of 10.53 MeV, nearly identical to the published 10.5 MeV for the emulated 10 MV Linac. The depth dose profile produced by their new Linac is within 1% of that produced by the emulated 10 MV spectrum for all depths greater than 1.5 cm. The penumbra produced is 11% narrower, as measured from 80% to 20% of the central axis dose. Conclusions: The authors have successfully designed and simulated an S-band waveguide of length of 27.5 cm capable of producing a 10 MV photon beam. This waveguide operates well within the breakdown threshold determined for the cavity geometry used. The designed Linac produces depth dose profiles similar to those of the emulated 10 MV Linac (waveguide-length of 1.5 m) but yields a narrower penumbra.

07 ISOTOPE AND RADIATION SOURCES↗

MULTI-SCALE MODELING AND APPROXIMATION ASSISTED OPTIMIZATION OF BARE TUBE HEAT EXCHANGERS

Air-to-refrigerant heat exchangers are very common in air-conditioning, heat pump and refrigeration applications. In these heat exchangers, there is a great benefit in terms of size, weight, refrigerant charge and heat transfer coefficient, by moving from conventional channel sizes (~ 9mm) to smaller channel sizes (< 5mm). This work investigates new designs for air-to-refrigerant heat exchangers with tube outer diameter ranging from 0.5 to 2.0mm. The goal of this research is to develop and optimize the design of these heat exchangers and compare their performance with existing state of the art designs. The air-side performance of various tube bundle configurations are analyzed using a Parallel Parameterized CFD (PPCFD) technique. PPCFD allows for fast-parametric CFD analyses of various geometries with topology change. Approximation techniques drastically reduce the number of CFD evaluations required during optimization. Maximum Entropy Design method is used for sampling and Kriging method is used for metamodeling. Metamodels are developed for the air-side heat transfer coefficients and pressure drop as a function of tube-bundle dimensions and air velocity. The metamodels are then integrated with an air-to-refrigerant heat exchanger design code. This integration allows a multi-scale analysis of air-side performance heat exchangers including air-to-refrigerant heat transfer and phase change. Overall optimization is carried out using a multi-objective genetic algorithm. The optimal designs found can exhibit 50 percent size reduction, 75 percent decrease in air side pressure drop and doubled air heat transfer coefficients compared to a high performance compact micro channel heat exchanger with same capacity and flow rates.

CFD↗

Numerical minimization of neoclassical poloidal viscosity for supersonic equilibria in tokamak geometry

Extensive experimental evidence has shown that the presence of poloidal flow in tokamaks can dramatically improve transport properties. However, theory indicates that poloidal flows are damped by poloidal viscosity, thus necessitating external drivers, such as neutral beam injection or radio frequency heating. In this work, ideal magnetohydrodynamic equilibria are calculated via the FORTRAN code FLOW [Guazzotto et al., Phys. Plasmas 11, 604 (2004)] and a postprocessor is used to estimate the neoclassical poloidal viscosity. The equilibrium inputs, which correspond to intuitive physical quantities, are then numerically optimized to reduce a viscosity figure of merit. We present supersonic equilibria in tokamak geometry with minimized neoclassical poloidal viscosities for various velocity free function inputs, plasma aspect ratios, and collisionality regimes. Benchmarks are made against an analytic theory as well as a classical expression of poloidal viscosity. Numerical confirmation of the analytic theory is obtained in the high aspect ratio and high collisionality limit. Good agreement is also seen near the plasma core and edge, with discrepancies arising in the intermediate region. Outside of these limits, rotation input function profiles are found that provide ∼order of magnitude improvements over the analytic theory, with additional progress being made toward predictions for tokamak-relevant equilibria.

Physics↗

OMEGA polar-drive target designs

Low-adiabat polar-drive (PD) [Skupsky et al., Phys. Plasmas 11, 2763 (2004)] implosion designs for the OMEGA [Boehly et al., Opt. Commun. 133, 495 (1997)] laser are described. These designs for cryogenic deuterium-tritium and warm plastic shells use a temporal laser pulse shape with three pickets followed by a main pulse [Goncharov et al., Phys. Rev. Lett. 104, 165001 (2010)]. The designs are at two different on-target laser intensities, with different in-flight aspect ratios (IFARs). These designs permit studies of implosion energetics and target performance closer to ignition-relevant intensities ({approx}7 Multiplication-Sign 10{sup 14} W/cm{sup 2} at the quarter-critical surface, where nonlocal heat conduction and laser-plasma interactions can play an important role) but at lower values of IFAR {approx} 22 or at lower intensity ({approx}3 Multiplication-Sign 10{sup 14} W/cm{sup 2}) but at a higher IFAR (IFAR {approx} 32, where shell instability can play an important role). PD geometry requires repointing of laser beams to improve shell symmetry. The higher-intensity designs optimize target performance by repointing beams to a lesser extent, compensating for the reduced equatorial drive by increasing the energies of the repointed beams. They also use custom beam profiles that improve equatorial illumination at the expense of irradiation at higher latitudes. These latter designs will be studied when new phase plates for the OMEGA Laser System, corresponding to the custom beam profiles, are obtained.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Tuning Band Gap Energies in Pb3(C6X6) Extended Solid-State Structures

A detailed plane-wave density functional theory investigation of the solid-state properties of the extended organometallic system Pb{sub 3}C{sub 6}X{sub 6} for X = O, S, Se, and Te has been performed. Initial geometry parameters for the Pb-X and C-X bond distances were obtained from optimized calculations on molecular fragment models. The Pb{sub 3}C{sub 6}X{sub 6} extended solid molecular structures were constructed in the space group P6/mmm on the basis of the known structure for X = S. Ground-state geometries, band gap energies, densities of states, and charge densities were calculated with the PBE-generalized gradient exchange-correlation functional and the HSE06 hybrid exchange-correlation functional. The PBE band gap energies were found to be lower than the HSE06 values by >0.7 eV. The band energies at points of high symmetry along the first Brillouin zone in the crystal were larger than the overall band gap of the system. Pb{sub 3}C{sub 6}O{sub 6} was predicted to be a direct semiconductor ({Lambda} point) with a PBE band gap of 0.28 eV and an HSE06 band gap of 1.06 eV. Pb{sub 3}C{sub 6}S{sub 6} and Pb{sub 3}C{sub 6}Se{sub 6} were predicted to have indirect band gaps. The PBE band gap for Pb{sub 3}C{sub 6}S{sub 6} was 0.98 eV, and the HSE06 band gap was 1.91 eV. The HSE06 value is in good agreement with the experimentally observed band gap of 1.7 eV. Pb{sub 3}C{sub 6}Se{sub 6} has a PBE band gap of 0.56 eV and a HSE06 band gap of 1.41 eV. Pb{sub 3}C{sub 6}Te{sub 6} was predicted to be metallic with both of the PBE and HSE06 functionals. A detailed analysis of the PBE band structure and partial density of states at two points before and after the metallic behavior reveals a change in orbital character indicative of band crossing in Pb{sub 3}C{sub 6}Te{sub 6}. These results show that the band gap energies can be fine-tuned by changing the substituent X atom.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optimization of Air-Gap Profile in Interior Permanent-Magnet Synchronous Motors for Torque Ripple Mitigation

Interior permanent magnet synchronous motors (IPMSMs) have been widely used due to their high efficiency and high power density. Minimization of torque pulsation resulting in vibration and acoustic noise is one of the important design considerations for IPMSMs. In this paper, a grid on/off search method for the rotor profile is proposed to mitigate torque pulsation. Selection of the rotor profile is due to the fact that air-gap is the most sensitive parameter in electric machines wherein changes in flux densities can cause substantial differences in the distribution of forces. A layer comprised of 20 partitions with a 0.1 mm thickness and 3 degrees wide grids have been introduced to the rotor surface for each pole and the possible geometries have been analyzed using finite element method (FEM) in ANSYS Maxwell. An optimal design was found that has the lowest torque ripple with a higher average torque compared to the original design. Genetic algorithm (GA) has also been applied to the method to automate the coupling between Maxwell and Matlab thereby saving the simulation time. Finally, complete structural analysis has been done for both of the original and optimal designs to verify the superiority and feasibility of the proposed design.

42 ENGINEERING↗

Crosslink V.0.11.x User Manual

CrossLink is a novel two-dimensional and three-dimensional geometry and mesh generation software package developed by the Simulation Tools team at Los Alamos National Laboratory. This software represents the third generation of topology-based mesh generation technology developed by the Department of Defense and the Department of Energy with a special focus on complex multi-material hydrodynamic applications, mesh scalability, and high-order element mesh generation. The topology-based meshing approach offered by CrossLink enables users to quickly and easily mesh complex geometries in a repeatable and robust manner. CrossLink’s topology-based meshing approach is well-suited for parametric design studies, parametric design optimization, damage scenario assessment, and iterative design modification (i.e. feature addition and/or removal). CrossLink’s python API allows workflow scripting of the geometry creation and mesh generation process for traceability, repeatability, data provenance, and version control. CrossLink consists of three main components: a graphical user interface (GUI), a geometry creation and mesh generation engine, and a python API that provides a workflow scripting interface to the geometry and meshing functions.

97 MATHEMATICS AND COMPUTING↗

A statistical, task-based evaluation method for three-dimensional x-ray breast imaging systems using variable-background phantoms

Purpose: For the last few years, development and optimization of three-dimensional (3D) x-ray breast imaging systems, such as digital breast tomosynthesis (DBT) and computed tomography, have drawn much attention from the medical imaging community, either academia or industry. However, there is still much room for understanding how to best optimize and evaluate the devices over a large space of many different system parameters and geometries. Current evaluation methods, which work well for 2D systems, do not incorporate the depth information from the 3D imaging systems. Therefore, it is critical to develop a statistically sound evaluation method to investigate the usefulness of inclusion of depth and background-variability information into the assessment and optimization of the 3D systems. Methods: In this paper, we present a mathematical framework for a statistical assessment of planar and 3D x-ray breast imaging systems. Our method is based on statistical decision theory, in particular, making use of the ideal linear observer called the Hotelling observer. We also present a physical phantom that consists of spheres of different sizes and materials for producing an ensemble of randomly varying backgrounds to be imaged for a given patient class. Lastly, we demonstrate our evaluation method in comparing laboratory mammography and three-angle DBT systems for signal detection tasks using the phantom's projection data. We compare the variable phantom case to that of a phantom of the same dimensions filled with water, which we call the uniform phantom, based on the performance of the Hotelling observer as a function of signal size and intensity. Results: Detectability trends calculated using the variable and uniform phantom methods are different from each other for both mammography and DBT systems. Conclusions: Our results indicate that measuring the system's detection performance with consideration of background variability may lead to differences in system performance estimates and comparisons. For the assessment of 3D systems, to accurately determine trade offs between image quality and radiation dose, it is critical to incorporate randomness arising from the imaging chain including background variability into system performance calculations.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Predictive Tools for Customizing Heat Treatment of Additively Manufactured Aerospace Components

Laser-bed powder fusion (LBPF) additive manufacturing is increasingly being used to produce components of complex geometries using the Ni-base superalloy Inconel 718. The composition and the microstructure of the alloy are currently well optimized for wrought components made using conventional manufacturing processes such as rolling, forging, extrusion, etc. The attractive mechanical properties of the alloy result from the underlying austenitic matrix with fine equiaxed grains, and a high density and uniform distribution of the precipitation hardening phase, γ". Heat treatment steps such as homogenization, solutioning and aging are well documented for the wrought alloy. However, when the same wrought alloy compositions are used for the additive manufacturing (AM) processes, the asprocessed microstructure is significantly different, because of the different thermal history associated with LBPF, including rapid solidification and multiple temperature excursions that lead to multiple re-melting and reheating in the solid state. Rapid solidification introduces potential non-equilibrium effects at the moving solid-liquid interfaces that impact the extent of solute segregation, as well as the morphology of the dendritic grains that form. In order to recover the target mechanical properties, AM components have to undergo post-process heat treatments. However, such heat treatments have to be custom designed for the AM process and the component geometry because of the expected vast differences in the microstructure at various locations of a component with complex geometry. The homogenization and precipitation steps should be optimized for the component so that target mechanical properties can be obtained throughout the part. The objective of this research is to utilize High Performance Computing in phase field simulations of microstructure evolution during post-processing of AM components. The physics-based modeling will be beneficial in reducing the experimental effort required for heat treatment process selection, optimization, and certification, thus leading to a significant reduction in energy consumption for AM and post-processing heat treatment. The optimization study will help identify heat treatments steps that are critical for development of a final desired microstructure with the minimum energy input. This combined with shortening of the production cycle (time-to-market) by reducing the number of failed parts (property targets), and reduction in the number of iterations for process optimization, will enable 30-40% savings in the energy costs. Phase field simulations of the degree of homogenization and the effect of local matrix composition on the nucleation and growth of competing precipitating phases were performed using the Microstructure Evolution Using Massively Parallel Phase Field Simulations code developed in-house at the Oak Ridge National Laboratory. The simulations were able to successfully capture the kinetics of nucleation and growth, and morphologies of various precipitating phases as a function of local matrix compositions and composition gradients characteristic of local microstructures arising from location-dependent variations in the thermal conditions. Future work will involve extending the simulations to a length scale consisting of multiple dendrites, so that the effect of homogenization on the coarsening of the dendrites can be simulated and used as an additional input to the optimization of the heat treatment process.

36 MATERIALS SCIENCE↗

Enhanced quantum efficiency of photoelectron emission, through surface textured metal electrodes

It is predicted that the quantum efficiency (QE) of photoelectron emission from metals may be enhanced, possibly by an order of magnitude, through optimized surface texture. Through extensive computational simulations, it is shown that the absorption enhancement in select surface groove geometries may be a dominant contributor to enhanced QE and corresponds to localized Fabry–Perot resonances. The inadequacy of extant analytical models in predicting the QE increase, and suggestions for further improvement, are discussed.

42 ENGINEERING↗

High‐throughput combinatorial approach expedites the synthesis of a lead‐free relaxor ferroelectric system

Abstract Developing novel lead‐free ferroelectric materials is crucial for next‐generation microelectronic technologies that are energy efficient and environment friendly. However, materials discovery and property optimization are typically time‐consuming due to the limited throughput of traditional synthesis methods. In this work, we use a high‐throughput combinatorial synthesis approach to fabricate lead‐free ferroelectric superlattices and solid solutions of (Ba 0.7 Ca 0.3 )TiO 3 (BCT) and Ba(Zr 0.2 Ti 0.8 )O 3 (BZT) phases with continuous variation of composition and layer thickness. High‐resolution x‐ray diffraction (XRD) and analytical scanning transmission electron microscopy (STEM) demonstrate high film quality and well‐controlled compositional gradients. Ferroelectric and dielectric property measurements identify the “optimal property point” achieved at the composition of 48BZT–52BCT. Displacement vector maps reveal that ferroelectric domain sizes are tunable by varying {BCT–BZT} N superlattice geometry. This high‐throughput synthesis approach can be applied to many other material systems to expedite new materials discovery and properties optimization, allowing for the exploration of a large area of phase space within a single growth. image

36 MATERIALS SCIENCE↗

Comparison of T-piece and concentric mixing systems for continuous flow synthesis of anatase nanoparticles in supercritical isopropanol/water

T-piece and concentric counter-flow mixing systems are compared in continuous flow supercritical solvothermal synthesis of TiO{sub 2} at identical system parameters. The phase pure anatase nanoparticle products were characterized with powder X-ray diffraction (PXRD), transmission electron microscopy (TEM) and small angle X-ray scattering (SAXS), and the particle size, size distribution and absolute crystallinity mapped as a function of temperature, precursor concentration, flow rate and pressure for the two different continuous flow reactors. The particles synthesized with the T-piece geometry are smaller with a narrower size distribution, possibly indicating a more effective mixing, than particles synthesized at the same conditions with concentric counter-flow geometry. In general, an increased synthesis temperature leads to an increase in absolute crystallinity. For the particles synthesized with the concentric reactor geometry crossing of the critical point of the solvent causes a decrease in the particle size and size distribution, and conditions just above the critical temperature are demonstrated to be optimal for continuous solvothermal synthesis of anatase. - Grapical Abstract: Direct experimental comparison of T-piece and concentric mixing geometries in supercritical continuous flow synthesis of anatase nanoparticles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

$\mathrm{IH}$-$\mathrm{GAN}$: A conditional generative model for implicit surface-based inverse design of cellular structures

Variable-density cellular structures can overcome connectivity and manufacturability issues of topologically optimized structures, particularly those represented as discrete density maps. However, the optimization of such cellular structures is challenging due to the multiscale design problem. Past work addressing this problem generally either only optimizes the volume fraction of single-type unit cells but ignoring the effects of unit cell geometry on properties, or considers the geometry–property relation but builds this relation via heuristics. In contrast, we propose a simple yet more principled way to accurately model the property to geometry mapping using a conditional deep generative model, named Inverse Homogenization Generative Adversarial Network (IH-GAN). It learns the conditional distribution of unit cell geometries given properties and can realize the one-to-many mapping from properties to geometries. Here we further reduce the complexity of IH-GAN by using the implicit function parameterization to represent unit cell geometries. Results show that our method can 1) generate various unit cells that satisfy given material properties with high accuracy (R 2 -scores between target properties and properties of generated unit cells >98%) and 2) improve the optimized structural performance over the conventional variable-density single-type structure. In the minimum compliance example, our IH-GAN generated structure achieves a 79.7% reduction in concentrated stress and an extra 3.03% reduction in displacement. In the target deformation examples, our IH-GAN generated structure reduces the target matching error by 86.4% and 79.6% for two test cases, respectively. We also demonstrated that the connectivity issue for multi-type unit cells can be solved by transition layer blending.

42 ENGINEERING↗

An Integrated Design Approach for Infill Patterning of Fused Deposition Modeling and its Application to an Airfoil

We present a new approach to incorporate an internal stress distribution into the design of infill via fused deposition modeling of additive manufacturing (AM). This design approach differs from topology optimization, since the topology optimization of AM focuses on changing the overall shape of the product, whereas the approach we propose in this research focuses on the porous infill and remains the overall shape of the product intact. The approach presented here is effective if the overall shape is an important functioning aspect of a product and the stress is applied to the entire body, not to given localized points. As an application, we demonstrate an airfoil with its infill densities optimized based on the pressure applied during operation. Specifically, the stress of an airfoil is analyzed with operational loading conditions. The local density of the infill pattern is determined based on the computational stress analysis. The infill geometry is mathematically generated using a circle packing algorithm. Test results show that the airfoil with the optimized infill outperforms the same shape with the traditional uniform infill pattern of an airfoil having the same weight.

Kim, Pum↗

Heat Exchanger Design Optimization for Mitigation of Diesel Engine Exhaust Fouling

Abstract The design optimization of a diesel exhaust-coupled heat and mass exchanger that drives a 2.71 kW cooling capacity absorption heat pump is presented in this study. Fouling layer thermal resistance and pressure drops from single-tube experiments are used to develop a thermodynamic, heat transfer, and pressure drop model for the exhaust-coupled desorber. A parametric study is performed to select a desorber design that meets system performance while minimizing footprint. Experimental heat duties and pressure drops are within 10% and 3%, respectively, of the model predictions. Thus, large data sets from single-tube experiments with representative geometries are successful in accounting for fouling effects at the component level. Desorber design optimization based on this approach ensures continued heat pump performance after fouling. This study, along with the single-tube experiments, presents a systematic approach to design exhaust-coupled heat exchangers while considering the effects of fouling. These results are applicable for a wide range of waste-heat recovery applications, and this method can be extended to different geometries and operating conditions.

Energy & Fuels↗

Microfluidic channel optimization to improve hydrodynamic dissociation of cell aggregates and tissue

Maximizing the speed and efficiency at which single cells can be liberated from tissues would dramatically advance cell-based diagnostics and therapies. Conventional methods involve numerous manual processing steps and long enzymatic digestion times, yet are still inefficient. In previous work, we developed a microfluidic device with a network of branching channels to improve the dissociation of cell aggregates into single cells. However, this device was not tested on tissue specimens, and further development was limited by high cost and low feature resolution. In this work, we utilized a single layer, laser micro-machined polyimide film as a rapid prototyping tool to optimize the design of our microfluidic channels to maximize dissociation efficiency. This resulted in a new design with smaller dimensions and a shark fin geometry, which increased recovery of single cells from cancer cell aggregates. We then tested device performance on mouse kidney tissue, and found that optimal results were obtained using two microfluidic devices in series, the larger original design followed by the new shark fin design as a final polishing step. We envision our microfluidic dissociation devices being used in research and clinical settings to generate single cells from various tissue specimens for diagnostic and therapeutic applications.

59 BASIC BIOLOGICAL SCIENCES↗

Machine learning and atomic layer deposition: Predicting saturation times from reactor growth profiles using artificial neural networks

In this work, we explore the application of deep neural networks to the optimization of atomic layer deposition (ALD) processes. In particular, we focus on a one-shot optimization problem, where we try to predict the optimal dose time that leads to saturation everywhere in the reactor based on thickness values measured at different points of an ALD reactor after a single trial growth. In order to tackle this problem, we introduce a dataset designed to train neural networks to predict saturation times based on these inputs for a cross-flow ALD reactor. Here, we then explore the predictive ability of artificial neural networks of different depths and sizes using a separate testing dataset to evaluate their accuracies. The results obtained show that networks trained using stochastic gradient descent methods can accurately predict saturation times without requiring any additional information on the surface kinetics. This provides a viable approach to minimize the number of experiments required to optimize new ALD processes in a known reactor, and it highlights the way machine learning can be leveraged for thin film growth and manufacturing. While the datasets and training procedure depend on the reactor geometry, the trained neural networks provide a general surrogate model connecting thickness values and trial dose times with optimal saturation times that can be reused for different ALD processes within the same reactor.

36 MATERIALS SCIENCE↗

Optimizing Multi-Robot Placements for Wire Arc Additive Manufacturing

Wire arc additive manufacturing is a metal additive manufacturing process in which the material is deposited using arc welding technology. It is gaining popularity due to high material deposition rates and faster build time. It is en-abled using robotic manipulators and can build relatively large-scale parts faster when compared with other metal additive manufacturing processes. However, the size of the large-scale parts is limited by the size of the industrial manipulator being used for the process. This limitation is overcome by using a fixed configuration multi-robot cell in which manipulators work cooperatively to build large-scale parts quickly. A fixed multi-robot cell with closely spaced industrial manipulators has high flexibility, but it restricts the part size that can be built. If the manipulators are spread out, the cell loses its flexibility but can build relatively larger parts. This issue can be avoided by using larger size manipulators, which are expensive, or by moving the modest size manipulators based on the part geometries. This paper presents a novel algorithm to generate multi-robot placements for different part geometries to be built using wire arc additive manufacturing. Furthermore, the algorithm hierarchically optimizes the build time and the inverse kinematics consistency in robot paths to improve the process efficiency and part quality. We compare the results with fixed multi-robot cells and provide insights to users to make an informed decision on whether to use a fixed or a flexible multi-robot cell for wire arc additive manufacturing.

Bhatt, Prahar↗