Search NASA⌕ Search

SEARCH · Search NASA

Results for “Image analysis.”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Impact of Organic-Liquid Distribution and Flow-Field Heterogeneity on Reductions in Mass Flux

A series of flow-cell experiments was conducted to investigate the impact of organic-liquid distribution and flow-field heterogeneity on the relationship between source-zone mass removal and reductions in contaminant mass flux from the source zone. Changes in source-zone architecture were quantified using image analysis, allowing explicit examination of their impact on the mass-flux-reduction/mass-removal behavior. The results showed that there was minimal reduction in mass flux until a large fraction of mass was removed for systems wherein organic liquid was present solely as residual saturation in regions that were hydraulically accessible. Conversely, significant reductions in mass flux occurred with relatively minimal mass removal for systems wherein organic liquid was present at both residual and higher saturations. The latter systems exhibited multi-step mass-flux-reduction/mass-removal behavior, and characterization of the organic-liquid saturation distribution throughout flushing allowed identification of the cause of the nonideal behavior. The age of the source zone (time from initial emplacement to time of initial characterization) significantly influenced the observed mass-flux-reduction/mass-removal behavior. The results of this study illustrate the impact of both organic-liquid distribution and flow-field heterogeneity on mass-removal and mass-flux processes.

54 ENVIRONMENTAL SCIENCES↗

Effect of powder layer thickness on the microstructural development of additively manufactured SS316

By Increasing the powder layer thickness we could increase material deposition rates and reduce build times during laser powder bed fusion (LPBF). However, increasing the powder layer thickness could also negatively affect the local melting and subsequent microstructure of the printed material. This study systematically investigated, for the first time, the defect evolution and microstructural changes of LPBF stainless steel 316 (SS316) processed by using various powder layer thicknesses of 40, 80, and 120 μm while also varying the laser dwell time for the pulsed laser. Through image analysis, the pore density was found to increase with increasing powder layer thickness, particularly when the dwell time was too high or too low. The maximum achievable density (>99%) was found over a wide processing window when using the smallest powder layer thickness of 40 μm between dwell times of 60 and 100 μs. Increasing the powder layer thicknesses to 80 and 120 μm resulted in maximum densities of 98.7 and 96.8%, respectively, but the window for acceptable laser dwell times that could achieve these densities narrowed considerably. A microstructural analysis of the melt pools was performed to measure the melt pool depths and widths, both of which increased with increasing dwell time. However, increasing the powder layer thickness did not affect the melt pool depth and only minorly affected the width. A sub-grain cellular structure distinguished the melt pool boundaries. The cell size increased with increasing dwell time and decreasing powder layer thickness. Moreover, the cell size was used to calculate a cooling rate that had a magnitude of 10 7 K/s and increased with increasing powder layer thickness.

36 MATERIALS SCIENCE↗

Potential Annealing Treatments for Tailoring the Starting Microstructure of Low-Enriched U-Mo Dispersion Fuels to Optimize Performance During Irradiation

Low-enriched uranium-molybdenum alloy particles dispersed in aluminum alloy (e.g., dispersion fuels) are being developed for application in research and test reactors. To achieve the best performance of these fuels during irradiation, optimization of the starting microstructure may be required by utilizing a heat treatment that results in the formation of uniform, Si-rich interaction layers between the U-Mo particles and Al-Si matrix. These layers behave in a stable manner under certain irradiation conditions. To identify the optimum heat treatment for producing these kinds of layers in a dispersion fuel plate, a systematic annealing study has been performed using actual dispersion fuel samples, which were fabricated at relatively low temperatures to limit the growth of any interaction layers in the samples prior to controlled heat treatment. These samples had different Al matrices with varying Si contents and were annealed between 450 and 525 C for up to 4 hours. The samples were then characterized using scanning electron microscopy (SEM) to examine the thickness, composition, and uniformity of the interaction layers. Image analysis was performed to quantify various attributes of the dispersion fuel microstructures that related to the development of the interaction layers. The most uniform layers were observed to form in fuel samples that had an Al matrix with at least 4 wt% Si and a heat treatment temperature of at least 475 C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Pore structure development in oxidized IG-110 nuclear graphite

The oxidation-induced porosity development in nuclear graphite has great effect on its mechanical behavior, thus it is very important to understand the pore structure development of nuclear graphite during oxidation. This paper reports on the oxidation kinetics of grade IG-110 nuclear graphite and the porosity development in oxidized samples. The distribution of the oxidized layer in IG-110 specimens oxidized at 600-750 C was studied using optical microscopy coupled with automated image analysis technique, and the mechanism of porosity development was determined. The thickness of oxidized layer decreased with the oxidation temperature but was independent of the weight loss level. Oxidation caused consumption of graphite structure and development of porosity, which was initiated from the binder phase. Statistical analysis indicated that generation and growth of pores was dominant at low temperatures, while merging and collapse of pores was the main effect at high temperatures. Compared with medium-grained PCEA graphite, the fine-grained IG-110 graphite demonstrates deeper penetration of the oxidant because of its higher pore density and lager porosity.

36 MATERIALS SCIENCE↗

Thermophysical properties of heat-treated U-7Mo/Al dispersion fuel

In this study, the effects of interaction layer (IL) on thermophysical properties of U-7Mo/Al dispersion fuel were examined. Microstructural analyses revealed that ILs were formed uniformly on U-Mo particles during heating of U-7Mo/Al samples. The IL volume fraction was measured by applying image analysis methods. The uranium loadings of the samples were calculated based on the measured meat densities at 298 K. The density of the IL was estimated by using the measured density and IL volume fraction. Thermal diffusivity and heat capacity of the samples after the heat treatment were measured as a function of temperature and volume fractions of U-Mo and IL. The thermal conductivity of IL-formed U-7Mo/Al was derived by using the measured thermal diffusivity, heat capacity, and density. The thermal conductivity obtained in the present study was lower than that predicted by the modified Hashin–Shtrikman model due to the theoretical model’s inability to consider the thermal resistance at interfaces between the meat constituents.

density↗

Processing of tungsten through electron beam melting

Additive manufacturing (AM) presents a new design paradigm for the manufacture of engineering materials through the layer-by-layer approach combined with welding theory. In the instance of difficult to process materials such as tungsten and other refractory metals, AM offers an opportunity for radical redesign of critical components for next-generation energy technologies including fusion. In this work, electron beam powder bed fusion (EB-PBF) is applied to process pure tungsten to study the influence of process parameters on the defect density of the material. Here, an in-situ image analysis algorithm is applied to pure tungsten for the first time, and is used to visualize the defect structure in AM tungsten. Finally, a cracking mechanism for AM tungsten is proposed, and suggestions for suppression of cracks in pure tungsten are offered.

36 MATERIALS SCIENCE↗

Quantitative Morphological Characterization of Carbide Inclusions in Uranium Metal

Uranium carbides (UCs) are prevalent inclusions in U metal that form during melting operations from interactions with crucible walls and the casting chamber atmosphere. Although UCs have been studied extensively since the beginning of U metal foundry operations, there are still unknowns regarding the effects of thermomechanical processing on their sizes and morphology. Here, we present the results of a series of controlled cooling experiments with molten uranium to elucidate the effect of cooling rate on inclusion morphology in a-U. Samples were melted using a vacuum induction melter and manually cooled at rates of 2.5, 1.7, 1.1, 0.8, 0.3 (± 1%) K/s from ~1600 K to <700 K in under 1 hour. Subsequent scanning electron microscopy (SEM) was performed on cross-sections of the samples, revealing a complex mixture of UC morphologies that are indicative of diffusion and growth influenced by the thermal processing of the U matrix. Image analysis using the Morphological Analysis of Materials (MAMA) software showed that UC sizes generally grew larger with slower cooling rates, and the two slowest cooling rates noticeably impacted the inclusion circularity and ellipse aspect ratio. These results indicate that UC morphology is sensitive to short cooling rates (<1 hour) and could therefore be controlled in the production of metallic nuclear fuels. Additionally, inclusion speciation and morphologies could potentially provide forensic clues about processing history of unknown metal samples. Understanding the driving forces involved in UC morphology evolution is beneficial for evaluating metal fuels for next generation nuclear reactors and for identifying signatures for nuclear forensics.

Athon, Matthew T.↗

An investigation of the failure modes in U-10Mo monolithic fuel irradiated to high burnup

Here, this study investigated possible failure mode sequences in U-10Mo monolithic fuel irradiated to very-high-burnup. The U-Mo fuel plate used in this study was characterized using scanning electron microscopy (SEM), wavelength dispersive spectroscopy (WDS), and image analysis techniques to investigate how microstructural features may initiate crack formation and propagation through the microstructure, potentially leading to blistering. Distinctly large fission gas pores (FGPs) were observed to preferentially align 5-15µm away from the U-10Mo/Zr interface, parallel to the Zr diffusion barrier. Preferential growth, alignment, and interconnection of FGP could initiate blistering in the fuel plate by creating a fission gas channel, parallel to the U-Mo/Zr interface. FGP alignment in the fuel phase near the U-Mo/Zr interface is believed to be one of the precursors to crack and Type 2 blister formation in monolithic U-Mo fuels. The chemical maps revealed differences in fission product behavior near the U-Mo/Zr interface such that Nd remains in the fuel matrix at the FGP sites. On the other hand, other fission products like Xe and Cs can get trapped in FGPs by Nd in the fuel phase and/or diffuse toward the Zr diffusion barrier.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Review of multi-faceted morphologic signatures of actinide process materials for nuclear forensic science

Particle morphology is an emerging signature that has the potential to identify the processing history of unknown nuclear materials. Using readily available scanning electron microscopes (SEM), the morphology of nearly any solid material can be measured within hours. Coupled with robust image analysis and classification methods, the morphological features can be quantified and support identification of the processing history of unknown nuclear materials. The viability of this signature depends on developing databases of morphological features, coupled with a rapid data analysis and accurate classification process. With developed reference methods, datasets, and throughputs, morphological analysis can be applied within days to (i) interdicted bulk nuclear materials (gram to kilogram quantities), and (ii) trace amounts of nuclear materials detected on swipes or environmental samples. In conclusion, this review aims to develop validated and verified analytical strategies for morphological analysis relevant to nuclear forensics.

36 MATERIALS SCIENCE↗

Sintering effects on NpO 2 grain size and morphology: The role of precursor Np phase

Neptunium dioxide (NpO 2 ) is a key phase in nuclear material processing as a target material for the production of plutonium-238 ( 238 Pu) and has been historically synthesized via the calcination of a Np oxalate precursor. Alternative synthesis methods for NpO 2 are now more prevalent, necessitating their study and comparison with the more common oxalate route. The purpose of this work was to investigate the microstructural properties of NpO 2 synthesized from a nitrate-based Np precursor phase via the assessment of NpO 2 particle size and morphology as a function of calcination temperature and time. Scanning electron microscopy (SEM) was used to probe the primary grain size and morphology of NpO 2 after calcination at temperatures ranging from 700 to 1100 °C and hold times ranging from 1 to 10 h. Post-image analysis using ImageJ software enabled the quantification of mean particle diameter. This analysis indicated that particle diameter increases with both increasing calcination temperature and hold time. Primary particles were shown to be clumped in irregular patterns into the overall rough, blocky aggregates, but this macroscopic morphology was not affected by calcination time or temperature. Although trends in primary grain size of NpO 2 were consistent with available literature from other Np precursor phases, the macroscopic morphology of the NpO 2 aggregates was quite different than reported for other precursors. Through comparison with historical literature on Np oxalate, this work emphasizes the importance of Np precursor on the physical properties of NpO 2 .

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Physical and hydraulic properties of modern sinter deposits: El Tatio, Atacama

We report sinters are siliceous, sedimentary deposits that form in geothermal areas. Formation occurs in two steps. Hot water circulates in the subsurface and dissolves silica from the host rock, usually rhyolites. Silica then precipitates after hot water is discharged and cools. Extensive sinter formations are linked to up-flow areas of fluids originating from high temperature (> 175 °C) deep reservoirs. Fluid geochemistry, microbial communities, and environmental conditions of deposition determine the texture of sinter and pore framework. Porosity strongly influences physical and hydraulic properties of rocks. To better understand the properties controlling the transport of fluids, and interpret geophysical observations in geothermal systems, here we studied 17 samples of modern geyserite sinter deposits (< 10 ka) from the active El Tatio geothermal field in northern Chile. We measured the physical properties (hydraulic, seismic, and electrical), and internal microstructure (using μX-Ray computed tomography). We find that the pore structure, and thus hydraulic and physical properties, is controlled by the distribution of microbial matter. Based on velocity-porosity relationships, permeability-porosity scaling, and image analysis of the 3D pore structure; we find that the physical and hydraulic properties of sinter more closely resemble those of vesicular volcanic rocks and other material formed by precipitation in geothermal settings (i.e., travertine) than clastic sedimentary rocks.

15 GEOTHERMAL ENERGY↗

Microstructural characterisation of nanocomposite nc-MeC/a-C coatings on oxygen hardened Ti-6Al-4V alloy

Nanocomposite coatings are novel, important systems composed of two or more nanocrystalline, or nanocrystalline and amorphous, phases. Such coatings offer a possibility of tailoring the coating microstructure and achieving new improved properties of coated materials. In this work a duplex surface treatment, consisting of an oxygen diffusion treatment and deposition of low friction nanocomposite nc-MeC/a-C (Me = transition metal, Ti, W or Cr) coatings, was applied for improvement of the Ti-6Al-4V alloy properties. The coatings composed of nanocrystallites of transition metal carbides (TiC or Cr{sub x}C{sub y} or WC) embedded in hydrogen-free amorphous carbon (a-C) matrix were deposited onto the surface of an oxygen hardened Ti-6Al-4 V alloy substrate by means of a simple DC magnetron sputtering. A nano/microstructure of the substrate material and coatings has been examined by scanning- and transmission electron microscopy complemented with the results of X-ray diffraction analyses. It was found that the nanocomposite coatings are composed of different carbide nanocrystals (with sizes of a few nanometres) embedded in an amorphous carbon matrix. The results of qualitative and quantitative analyses of the nanocrystalline phase in the coatings with use of high-resolution transmission electron microscopy combined with image analysis are given in the paper. An effect of the nano/microstructure parameters of the coated alloy onto its micro-mechanical (nanohardness and Young's modulus) and tribological properties (wear resistance and friction coefficient) is discussed in the paper.

36 MATERIALS SCIENCE↗

Effect of thermally stable Cu- and Mg-rich aluminides on the high temperature strength of an AlSi12CuMgNi alloy

The internal architecture of an AlSi12CuMgNi piston alloy, revealed by synchrotron tomography, consists of three dimensional interconnected hybrid networks of Cu-rich aluminides, Mg-rich aluminides and eutectic/primary Si embedded in an α-Al matrix. The strength at room temperature and at 300°C is studied as a function of solution treatment time at 490°C and compared with results previously reported for an AlSi12Ni alloy. The addition of 1 wt% Cu and 1 wt% Mg to AlSi12CuMgNi increases the room temperature strength by precipitation hardening while the strength at 300°C is similar for both alloys in as-cast condition. The strength of AlSi12CuMgNi decreases with solution treatment time and stabilizes at 4 h solution treatment. The effect of solution treatment time on the strength of the AlSi12CuMgNi alloy is less pronounced than for the AlSi12Ni alloy both at room temperature and at 300°C. - Highlights: • The 3D microstructure of AlSi12CuMgNi is revealed by synchrotron tomography. • An imaging analysis procedure to segment phases with similar contrasts is presented. • 1 wt% Cu and Mg results in the formation of 3D networks of rigid phases. • AlSi12CuMgNi is stronger than AlSi12Ni owing to the stability of the 3D networks.

36 MATERIALS SCIENCE↗

Microstructure characterization via stereological relations — A shortcut for beginners

Stereological relations that can be routinely applied for the quantitative characterization of microstructures of heterogeneous single- and two-phase materials via global microstructural descriptors are reviewed. It is shown that in the case of dense, single-phase polycrystalline materials (e.g., transparent yttrium aluminum garnet ceramics) two quantities have to be determined, the interface density (or, equivalently, the mean chord length of the grains) and the mean curvature integral density (or, equivalently, the Jeffries grain size), while for two-phase materials (e.g., highly porous, cellular alumina ceramics), one additional quantity, the volume fraction (porosity), is required. The Delesse–Rosiwal law is recalled and size measures are discussed. It is shown that the Jeffries grain size is based on the triple junction line length density, while the mean chord length of grains is based on the interface density (grain boundary area density). In contrast to widespread belief, however, these two size measures are not alternative, but independent (and thus complementary), measures of grain size. Concomitant with this fact, a clear distinction between linear and planar grain size numbers is proposed. Finally, based on our concept of phase-specific quantities, it is shown that under certain conditions it is possible to define a Jeffries size also for two-phase materials and that the ratio of the mean chord length and the Jeffries size has to be considered as an invariant number for a certain type of microstructure, i.e., a characteristic value that is independent of the absolute size of the microstructural features (e.g., grains, inclusions or pores). - Highlights: • Stereology-based image analysis is reviewed, including error considerations. • Recipes are provided for measuring global metric microstructural descriptors. • Size measures are based on interface density and mean curvature integral density. • Phase-specific quantities and a generalized Jeffries size are introduced. • Linear and planar grain size numbers are clearly distinguished and explained.

36 MATERIALS SCIENCE↗

Preparation, phase structure and microwave dielectric properties of CoLi{sub 2/3}Ti{sub 4/3}O{sub 4} ceramic

Graphical abstract: For chemical compatibility tests with silver electrode, mixtures of ceramic powders with 20 wt% Ag powders were cofired and analyzed to detect interactions between the low-fired samples and electrodes. XRD patterns and backscattered electron image of CoLi{sub 2/3}Ti{sub 4/3}O{sub 4} ceramics added with 1.5 wt% BCB cofired with Ag at 900 Degree-Sign C for 2 h are presented in . Backscattered electron image analysis reveals no interaction to form new phases after firing. This observation is also confirmed by the evidence of no difference between the XRD patterns before and after firing. It is obvious that the reaction of low-fired CoLi{sub 2/3}Ti{sub 4/3}O{sub 4} ceramics with Ag electrodes did not occur. Highlights: Black-Right-Pointing-Pointer A new microwave dielectric ceramic with good properties was reported. Black-Right-Pointing-Pointer The addition of BaCu(B{sub 2}O{sub 5}) can lower the sintering temperature from 1050 Degree-Sign C to 900 Degree-Sign C. Black-Right-Pointing-Pointer The addition of BaCu(B{sub 2}O{sub 5}) does not induce degradation of properties. Black-Right-Pointing-Pointer BCB added CoLi{sub 2/3}Ti{sub 4/3}O{sub 4} ceramics can co-fire with Ag electrode. -- Abstract: A new low loss microwave dielectric ceramic with composition of CoLi{sub 2/3}Ti{sub 4/3}O{sub 4} was prepared by a conventional solid-state reaction method. The compound has a cubic spinel structure [Fd-3m (227)] similar to MgFe{sub 2}O{sub 4} with lattice parameters of a = 8.3939 Angstrom-Sign , V = 591.42 Angstrom-Sign {sup 3}, Z = 8 and {rho} = 4.30 g/cm{sup 3}. This ceramic has a low sintering temperature ({approx}1050 Degree-Sign C) and good microwave dielectric properties with relative permittivity of 21.4, Q Multiplication-Sign f value of 35,000 GHz and {tau}{sub f} value of -22 ppm/ Degree-Sign C. Furthermore, the addition of BaCu(B{sub 2}O{sub 5}) (BCB) can effectively lower the sintering temperature from 1050 Degree-Sign C to 900 Degree-Sign C and does not induce much degradation of the microwave dielectric properties. Compatibility with Ag electrode indicates that the BCB added CoLi{sub 2/3}Ti{sub 4/3}O{sub 4} ceramics are good candidates for LTCC applications.

36 MATERIALS SCIENCE↗

Grain subdivision and structural modifications by high-energy heavy ions in UO 2 with different initial grain size

Irradiation with 84 MeV Xe ions at peak fluence above 7 × 10 17 ions/cm 2 has been carried out on two UO 2 samples with different initial grain sizes at 300 °C and 500 °C. Characterization of both grain structure and bubble morphology has been performed using transmission electron microscopy, image analysis and precession electron diffraction. The bubble size in the large-grained sample was smaller than that in the standard-grain sample, confirming fission gas precipitation resistance in the former. The ion irradiation in the high electronic energy deposition range has caused formation of a large density of dislocations which resulted in grain polygonization for the sample with standard grain size, which was observed in multiple lamellas extracted next to each other at peak dose. The sample with large grains showed inconsistent behavior. In one case, dislocation pile-up occurred, but no sub-grain formation was observed. An adjacent location showed sub-grain formation, even if to less extent compared to the standard grain-size sample. Furthermore, these findings suggest a limited polygonization resistance in large-grained UO 2 compared to standard-grain UO 2 . Recrystallization of both sample surfaces was present, leaving unclear if this is a surface effect or a consequence of the highest energy deposition rate in this area.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Facile Synthesis of Thiol-terminated Poly(styrene-ran-vinyl phenol) (PSVPh) Copolymers via Reversible Addition-Fragmentation Chain Transfer (RAFT) Polymerization and Their Use in the Synthesis of Gold Nanoparticles with Controllable Hydrophilicity

A facile approach to prepare thiol-terminated poly(styrene-ran-vinyl phenol) (PSVPh) copolymers and PSVPh-coated gold nanoparticles is reported with the goal of creating stabilizing ligands for nanoparticles with controlled hydrophilicity. Dithioester-terminated poly(styrene-ran-acetoxystyrene) copolymers were synthesized via RAFT polymerization using cumyl dithiobenzoate as a chain transfer agent. These copolymers were converted to thiol-terminated PSVPh copolymers by a one step hydrazinolysis reaction using hydrazine hydrate to simultaneously convert dithioester-terminal and acetoxypendant groups to thiol-terminal and hydroxyl-pendant groups, respectively. Spectroscopic observations including NMR and IR confirm end- and pendant-group conversion. PSVPh-coated gold nanoparticles were synthesized in the presence of a mixture of thiol-terminated PSVPh and PSVPh copolymers containing disulfides as stabilizing ligands in a water/toluene, two-phase system. The size and size distribution of core gold nanoparticles were determined by TEM and image analysis. The hydrodynamic radius of PSVPh-coated gold nanoparticles was also determined by dynamic light scattering experiment, which confirms the particle analysis by TEM. This procedure provides a facile technique to control the polarity and hydrophilicity of metal nanoparticle surfaces and could prove critical in advancing the control of nanoparticle placement in biological and hierarchically ordered systems, such as diblock copolymers.

36 MATERIALS SCIENCE↗

Experimental study on flow characterization of a rectangular spouted bed by image processing

Systematic image processing methods are applied to characterize gas-solid flow under different operating conditions in a 30.2 mm x 101.6 mm rectangular spouted bed. Geldart D particles are imaged using a highspeed video camera. Superficial gas velocity, initial bed height, and nozzle size are investigated as influence factors. By applying adaptive thresholding and logical operation to the video frames, the original color images are transformed into binary images exposing detailed boundary information. By analyzing the binary image using a self-developed algorithm in combination with mask operations, the bed height is successfully determined, through which the variation of the bed expansion ratio with superficial gas velocity can be obtained. Additionally, the application of image morphological operations, i.e. dilation and erosion on the binarized images ensures the accurate identification of the contours of the jet and fountain so that the jet and fountain heights can be determined. Based on the image processing methods, the variation of bed expansion ratio, jet height and fountain height with the three influence factors are discussed. The current study highlights the application of image analysis in investigating the flow characterization and obtaining more hydrodynamic information in a rectangular spouted bed.

42 ENGINEERING↗