Search NASA⌕ Search

SEARCH · Search NASA

Results for “Simulation Use Case”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Experimental and Analytical Characterization of the Macromechanical Response for Triaxial Braided Composite Materials

Increasingly, carbon composite structures are being used in aerospace applications. Their highstrength, high-stiffness, and low-weight properties make them good candidates for replacing many aerospace structures currently made of aluminum or steel. Recently, many of the aircraft engine manufacturers have developed new commercial jet engines that will use composite fan cases. Instead of using traditional composite layup techniques, these new fan cases will use a triaxially braided pattern, which improves case performance. The impact characteristics of composite materials for jet engine fan case applications have been an important research topic because Federal regulations require that an engine case be able to contain a blade and blade fragments during an engine blade-out event. Once the impact characteristics of these triaxial braided materials become known, computer models can be developed to simulate a jet engine blade-out event, thus reducing cost and time in the development of these composite jet engine cases. The two main problems that have arisen in this area of research are that the properties for these materials have not been fully determined and computationally efficient computer models, which incorporate much of the microscale deformation and failure mechanisms, are not available. The research reported herein addresses some of the deficiencies present in previous research regarding these triaxial braided composite materials. The current research develops new techniques to accurately quantify the material properties of the triaxial braided composite materials. New test methods are developed for the polymer resin composite constituent and representative composite coupons. These methods expand previous research by using novel specimen designs along with using a noncontact measuring system that is also capable of identifying and quantifying many of the microscale failure mechanisms present in the materials. Finally, using the data gathered, a new hybrid micromacromechanical computer model is created to simulate the behavior of these composite material systems under static and ballistic impact loading using the test data acquired. The model also quantifies the way in which the fiber/matrix interface affects material response under static and impact loading. The results show that the test methods are capable of accurately quantifying the polymer resin under a variety of strain rates and temperature for three loading conditions. The resin strength and stiffness data show a clear rate and temperature dependence. The data also show the hydrostatic stress effects and hysteresis, all of which can be used by researchers developing composite constitutive models for the resins. The results for the composite data reveal noticeable differences in strength, failure strain, and stiffness in the different material systems presented. The investigations into the microscale failure mechanisms provide information about the nature of the different material system behaviors. Finally, the developed computer model predicts composite static strength and stiffness to within 10 percent of the gathered test data and also agrees with composite impact data, where available.

Littell, Justin D.↗

A Human-In-The-Loop Simulation for Urban Air Mobility in the Terminal Area

In this paper researchers propose a human-in-the-loop experiment to study human performance when tasked with tactical deconfliction in terminal area air taxi operations. The air taxi operations being considered herein are an advanced air transportation concept called Urban Air Mobility (UAM). The UAM concept aims to support not only air taxi operations, but also package delivery and emergency response among other use cases. The key innovation over current air transportation lies with the introduction of highly automated aircraft and air traffic management systems. Development of the UAM system will include transitional midterm phases where some operational services will be provided by a mixture of automation and human actors. Midterm operations present a unique challenge, since the scope of responsibility of automated systems is largely undefined, suggesting the need for direct human participation with little to inform how much human intervention is necessary. Here it is assumed that traffic management responsibilities require coordination between human actors and automated systems and focus on arrival flows for midterm operations. In the proposed human-in-the-loop simulation, virtual UAM traffic is strategically deconflicted by a Provider of Services for UAM at departure, then tactically managed by a human at the arrival facility. Generated traffic consists of UAM participants flying in UAM exclusive airspace structures, thus isolated from traditional traffic. The human operator is tasked with managing spacing of arrival traffic and executing speed adjustments as deemed necessary. Researchers propose the investigation of three levels of automation assistance: 1) no assistance; 2) spacing violation detection; 3) spacing violation detection and speed adjustment recommendations. Quantitative measures like throughput and delay are used to assess the human's capacity for accommodating airborne delays. Qualitative evaluations such as surveys and open-ended feedback are used to gain insight into human factors. These factors could introduce additional capacity constraints on traffic, independent of physical or technical constraints. Although findings for this study will not be reported as the study has not yet been executed, the authors conclude with potential outcomes informed by previous simulations in the literature and suggestions for the structure and procedures of midterm human-automation air traffic management.

UAM↗

The Effect of Two-Dimensional Forcing on Self-Similar Turbulent Plane Wakes

Three direct numerical simulations of time-evolving turbulent plane wakes with velocity deficit Reynolds numbers of about 2,000 have been simulated using a spectral numerical method with up to 600 x 260 x 160 modes. The initial conditions for the simulations are generated from direct numerical simulations of a turbulent boundary layer (momentum thickness Reynolds number of 670), and varying amounts of additional two- dimensional, forcing. In order to preserve the self-similar flow evolution, the forcing is implemented by multiplying all the two-dimensional modes in the initial condition by a constant factor. In the "natural" case no additional forcing is used; in the "forced" and "heavily forced" cases this factor is 5 and 20, respectively. The wake spreading rate Is increased by factors of 1.7 and 7.1 for the two forced cases. The Reynolds stresses are also increased by a similar or even larger factor. These results indicate that the plane wake is much more sensitive to initial forcing than the plane mixing layer. As in the plane mixing layer, two-dimensional forcing promotes more organized large-scale vortical flow structures and these structures axe sometimes separated by "braid regions" containing streamwise "rib" vortices, unlike in the unforced wake.

Rogers, M. M.↗

Simulation of flat-plate turbulent boundary layers in cryogenic tunnels

The magnitudes of real-gas effects on flat-plate turbulent boundary layer simulations in a cryogenic nitrogen wind tunnel are investigated in order to determine the validity of the method used by Inger (1979) to estimate real-gas effects. Boundary layer solutions for real gases, ideal gases with a specific heat ratio of 1.6 and ideal diatomic gases (specific heat ratio 1.4) were obtained for the worst case conditions of maximum stagnation pressure (9 atm), minimum stagnation temperature (120 K) and Mach number of 1.2. Calculated boundary layer parameters such as friction coefficient and displacement thickness are shown to agree closely for the real gas and the ideal diatomic gas (specific heat ratio 1.4), while the ideal gas solution used by Inger is shown to differ from the real-gas values considerably. Results indicate that real-gas effects on a flat-plate turbulent boundary layer simulation in a cryogenic nitrogen tunnel are insignificant, and suggest the unlikelihood of the large real-gas effects reported by Inger for turbulent boundary layer shock interactions.

Adcock, J.↗

Importance of Internal Variability for Climate Model Assessment

Benchmarking climate model simulations against observations of the climate is core to the process of building realistic climate models and developing accurate future projections. However, in many cases, models do not match historical observations, particularly on regional scales. If there is a mismatch between modeled and observed climate features, should we necessarily conclude that our models are deficient? Using several illustrative examples, we emphasize that internal variability can easily lead to marked differences between the basic features of the model and observed climate, even when decades of model and observed data are available. This can appear as an apparent failure of models to capture regional trends or changes in global teleconnections, or simulation of extreme events. Despite a large body of literature on the impact of internal variability on climate, this acknowledgment has not yet penetrated many model evaluation activities, particularly for regional climate. We emphasize that using a single or small ensemble of simulations to conclude that a climate model is in error can lead to premature conclusions on model fidelity. A large ensemble of multidecadal simulations is therefore needed to properly sample internal climate variability in order to robustly identify model deficiencies and convincingly demonstrate progress between generations of climate models.

Climate and Earth system modelling↗

Three-dimensional numerical simulation of near-surface flows over the Martian north polar cap

Measurements made by Viking Lander VL-2 (48 N) have shown that the near-surface wind and temperature regime on Mars displays striking similarities to terrestrial counterparts. The diurnal radiative cycle is responsible for establishment of a well-defined thermal circulation in which downslope (Katabatic) flows prevail during the nighttime hours and weak upslope (anabatic) conditions prevail during the daytime. Previous work has indicated that the slope flows are much like those found on Earth, particularly the Katabatic winds, which show striking similarities to drainage flows observed over Antarctica. The low-level wind regime appears to be an important factor in the scouring of the martian landscape. The north polar cap shows evidence of eolian features such as dunes, frost streaks, and grooves from Viking imagery. The direction of the prevailing wind can in cases be inferred from the eolian features. We examine the thermally induced flows that result from the radiative heating and cooling of the martian north polar region using a comprehensive three-dimensional atmospheric mesoscale numerical model. The same model has been used previously for simulation of Antarctic Katabatic winds. The model equations are written in terrain-following coordinates to allow for irregular terrain; prognostic equations include the flux forms of the horizontal momentum equations, temperature, continuity. A surface energy budget equation is also incorporated in which the surface temperature is determined. Explicit parameterization of both terrestrial (longwave) and solar (shortwave) radiation is included. Turbulent transfer of heat and momentum in the martian atmosphere is assumed to follow the similarity expressions in the surface boundary layer on Earth. The terrain heights for the martian north polar region have been obtained from the U.S. Geological Survey map and digitized onto a 57x57 grid with a spacing of 75 km. The resulting terrain map is shown in Fig. 1. The vertical grid consists of 15 levels (delta equals 0.998, 0.99, 0.98, 0.97, 0.96, 0.94, 0.92, 0.90, 0.85, 0.775, 0.70, 0.60, 0.50, 0.30, 0.10). The high resolution in the lower atmosphere is necessary to capture details of the boundary layer flows. The lowest level corresponds to a height of approximately 20 m above the ground, the seconds level 100 m.

Parish, Thomas R.↗

An Analytical Solution for Yaw Maneuver Optimization on the International Space Station and Other Orbiting Space Vehicles

This paper suggests a new method for optimizing yaw maneuvers on the International Space Station (ISS). Yaw rotations are the most common large maneuvers on the ISS often used for docking and undocking operations, as well as for other activities. When maneuver optimization is used, large maneuvers, which were performed on thrusters, could be performed either using control moment gyroscopes (CMG), or with significantly reduced thruster firings. Maneuver optimization helps to save expensive propellant and reduce structural loads ‐ an important factor for the ISS service life. In addition, optimized maneuvers reduce contamination of the critical elements of the vehicle structure, such as solar arrays. This paper presents an analytical solution for optimizing yaw attitude maneuvers. Equations describing pitch and roll motion needed to counteract the major torques during a yaw maneuver are obtained. A yaw rate profile is proposed. Also the paper describes the physical basis of the suggested optimization approach. In the obtained optimized case, the torques are significantly reduced. This torque reduction was compared to the existing optimization method which utilizes the computational solution. It was shown that the attitude profiles and the torque reduction have a good match for these two methods of optimization. The simulations using the ISS flight software showed similar propellant consumption for both methods. The analytical solution proposed in this paper has major benefits with respect to computational approach. In contrast to the current computational solution, which only can be calculated on the ground, the analytical solution does not require extensive computational resources, and can be implemented in the onboard software, thus, making the maneuver execution automatic. The automatic maneuver significantly simplifies the operations and, if necessary, allows to perform a maneuver without communication with the ground. It also reduces the probability of command errors. The suggested analytical solution provides a new method of maneuver optimization which is less complicated, automatic and more universal. A maneuver optimization approach, presented in this paper, can be used not only for the ISS, but for other orbiting space vehicles.

Dobrinskaya, Tatiana↗

A unified approach to aircraft parameter identification

The most accurate identification results are obtained when all three elements of the identification process - the identification algorithm, the control input, and the instrumentation system - are considered in a unified approach. This type of approach for the design of optimal control inputs and for determining the effect of the instrumentation system, in each case with respect to the identification process is discussed. Design of control inputs which optimize the sensitivity of the system output to the unknown parameters is given. Results using these inputs in an extensive simulation of the identification process indicate they perform measurably better than doublet type inputs. A technique is then presented for specifying an optimal instrumentation system or for determining the effect, the instrumentation system has on the accuracy of the parameter estimates.

Stepner, D. E.↗

Aerodynamic Characteristics of an A-4B Aircraft with Simulated and Actual Gunfire Damage to One Wing

The aerodynamic characteristics of a damaged McDonnell Douglas A-4B aircraft were studied in the Ames Research Center's 40- by 80-Foot Wind Tunnel. A standard fuselage and three different wings were used. The first wing tested was an undamaged one in which holes had been cut and detachable cover plates installed. Removal of one or more cover plates gave one of fourteen different simulated damage cases. The other two wings tested were damaged by actual gunfire at an Air Force range.

Betzina, M. D.↗

A multidomain global modeling technique for analysis of Space Shuttle main engine

A multidomain global modeling technique is presented. The purpose of this multidomain methodology is to simultaneously analyze the three-dimensional compressible flow field in Space Shuttle main engine components. This technique provides flexibility and modularity for individual domain and also simplifies the grid generation task for each domain. A two-way coupling procedure is adopted for exchanging interface boundary conditions. This algorithm which requires that the adjacent domains share an overlapping grid slab, is fully conservative and implicit. For non-matching grid systems and for non-overlapping interfaces, an interpolation and/or extrapolation procedure is used when transferring the interface boundary conditions at the adjacent domains. To maintain overall conservation, a flux correction method is subsequently used. The coupling procedure was verified by modeling several geometries with features similar to SSME components. Satisfactory results for all test cases were obtained. Finally, this algorithm has been applied to the SSME flow simulation.

Tam, L. T.↗

Simulated final approach path captures using the microwave landing system

Computer simulation results are presented for intercepting final approach paths using various Microwave Landing System (MLS) path capture concepts. This study, conducted under the Advanced Transport Operating System (ATOPS) program, simulated these captures using the MD-80 aircraft as the study model. Several different capture concepts were investigated. Systems that could be retrofitted into existing aircraft with minimum hardware and software changes were considered. An enhanced ILS look-alike capture provided improved tracking performance over conventional ILS without using a full-up path computer. The other concepts used waypoint databases and path computers to provide smart captures. These captures included lateral path intercepts as well as vertical path control. Winds, turbulence, and MLS noise were included in the simulation. In all cases, acceptable tracking errors were obtained during transition to the final approach path.

Feather, J. B.↗

Computer-aided system design

A technique has been developed for combining features of a systems architecture design and assessment tool and a software development tool. This technique reduces simulation development time and expands simulation detail. The Architecture Design and Assessment System (ADAS), developed at the Research Triangle Institute, is a set of computer-assisted engineering tools for the design and analysis of computer systems. The ADAS system is based on directed graph concepts and supports the synthesis and analysis of software algorithms mapped to candidate hardware implementations. Greater simulation detail is provided by the ADAS functional simulator. With the functional simulator, programs written in either Ada or C can be used to provide a detailed description of graph nodes. A Computer-Aided Software Engineering tool developed at the Charles Stark Draper Laboratory (CSDL CASE) automatically generates Ada or C code from engineering block diagram specifications designed with an interactive graphical interface. A technique to use the tools together has been developed, which further automates the design process.

Walker, Carrie K.↗

Numerical Modeling of Three-Dimensional Fluid Flow with Phase Change

We present a numerical method to compute phase change dynamics of three-dimensional deformable bubbles. The full Navier-Stokes and energy equations are solved for both phases by a front tracking/finite difference technique. The fluid boundary is explicitly tracked by discrete points that are connected by triangular elements to form a front that is used to keep the stratification of material properties sharp and to calculate the interfacial source terms. Two simulations are presented to show robustness of the method in handling complex phase boundaries. In the first case, growth of a vapor bubble in zero gravity is studied where large volume increase of the bubble is managed by adaptively increasing the front resolution. In the second case, growth of a bubble under high gravity is studied where indentation at the rear of the bubble results in a region of large curvature which challenges the front tracking in three dimensions.

Esmaeeli, Asghar↗

Comparison of Fatigue Life Estimation Using Equivalent Linearization and Time Domain Simulation Methods

The Monte Carlo simulation method in conjunction with the finite element large deflection modal formulation are used to estimate fatigue life of aircraft panels subjected to stationary Gaussian band-limited white-noise excitations. Ten loading cases varying from 106 dB to 160 dB OASPL with bandwidth 1024 Hz are considered. For each load case, response statistics are obtained from an ensemble of 10 response time histories. The finite element nonlinear modal procedure yields time histories, probability density functions (PDF), power spectral densities and higher statistical moments of the maximum deflection and stress/strain. The method of moments of PSD with Dirlik's approach is employed to estimate the panel fatigue life.

Mei, Chuh↗

Development of Flow and Heat Transfer Models for the Carbon Fiber Rope in Nozzle Joints of the Space Shuttle Reusable Solid Rocket Motor

Methodologies have been developed for modeling both gas dynamics and heat transfer inside the carbon fiber rope (CFR) for applications in the space shuttle reusable solid rocket motor joints. Specifically, the CFR is modeled using an equivalent rectangular duct with a cross-section area, friction factor and heat transfer coefficient such that this duct has the same amount of mass flow rate, pressure drop, and heat transfer rate as the CFR. An equation for the friction factor is derived based on the Darcy-Forschheimer law and the heat transfer coefficient is obtained from pipe flow correlations. The pressure, temperature and velocity of the gas inside the CFR are calculated using the one-dimensional Navier-Stokes equations. Various subscale tests, both cold flow and hot flow, have been carried out to validate and refine this CFR model. In particular, the following three types of testing were used: (1) cold flow in a RSRM nozzle-to-case joint geometry, (2) cold flow in a RSRM nozzle joint No. 2 geometry, and (3) hot flow in a RSRM nozzle joint environment simulator. The predicted pressure and temperature history are compared with experimental measurements. The effects of various input parameters for the model are discussed in detail.

Wang, Q.↗

Bondi Accretion and the Problem of the Missing Isolated Neutron Stars

A large number of neutron stars (NSs), approximately 10(exp 9), populate the Galaxy, but only a tiny fraction of them is observable during the short radio pulsar lifetime. The majority of these isolated NSs, too cold to be detectable by their own thermal emission, should be visible in X-rays as a result of accretion from the interstellar medium. The ROSAT All-Sky Survey has, however, shown that such accreting isolated NSs are very elusive: only a few tentative candidates have been identified, contrary to theoretical predictions that up to several thousand should be seen. We suggest that the fundamental reason for this discrepancy lies in the use of the standard Bondi formula to estimate the accretion rates. We compute the expected source counts using updated estimates of the pulsar velocity distribution, realistic hydrogen atmosphere spectra, and a modified expression for the Bondi accretion rate, as suggested by recent MHD simulations and supported by direct observations in the case of accretion around supermassive black holes in nearby galaxies and in our own. We find that, whereas the inclusion of atmospheric spectra partly compensates for the reduction in the counts due to the higher mean velocities of the new distribution, the modified Bondi formula dramatically suppresses the source counts. The new predictions are consistent with a null detection at the ROSAT sensitivity.

Perna, Rosalba↗

Heating Augmentation for Short Hypersonic Protuberances

Computational aeroheating analyses of the Space Shuttle Orbiter plug repair models are validated against data collected in the Calspan University of Buffalo Research Center (CUBRC) 48 inch shock tunnel. The comparison shows that the average difference between computed heat transfer results and the data is about 9.5%. Using CFD and Wind Tunnel (WT) data, an empirical correlation for estimating heating augmentation on short hypersonic protuberances (k/delta less than 0.3) is proposed. This proposed correlation is compared with several computed flight simulation cases and good agreement is achieved. Accordingly, this correlation is proposed for further investigation on other short hypersonic protuberances for estimating heating augmentation.

Mazaheri, Ali R.↗

The Impact of Geoengineering Aerosols on Stratospheric Temperature and Ozone

Anthropogenic greenhouse gas emissions are warming the global climate at an unprecedented rate. Significant emission reductions will be required soon to avoid a rapid temperature rise. As a potential interim measure to avoid extreme temperature increase, it has been suggested that Earth's albedo be increased by artificially enhancing stratospheric sulfate aerosols. We use a 3D chemistry climate model, fed by aerosol size distributions from a zonal mean aerosol model, to simulate continuous injection of 1-10 Mt/a into the lower tropical stratosphere. In contrast to the case for all previous work, the particles are predicted to grow to larger sizes than are observed after volcanic eruptions. The reason is the continuous supply of sulfuric acid and hence freshly formed small aerosol particles, which enhance the formation of large aerosol particles by coagulation and, to a lesser extent, by condensation. Owing to their large size, these particles have a reduced albedo. Furthermore, their sedimentation results in a non-linear relationship between stratospheric aerosol burden and annual injection, leading to a reduction of the targeted cooling. More importantly, the sedimenting particles heat the tropical cold point tropopause and, hence, the stratospheric entry mixing ratio of H2O increases. Therefore, geoengineering by means of sulfate aerosols is predicted to accelerate the hydroxyl catalyzed ozone destruction cycles and cause a significant depletion of the ozone layer even though future halogen concentrations will be significantly reduced.

Heckendorn, P.↗