SEARCH · Search NASA

Results for “Simulation techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Theoretical and simulated performance for a novel frequency estimation technique

A low complexity, open-loop, discrete-time, delay-multiply-average (DMA) technique for estimating the frequency offset for digitally modulated MPSK signals is investigated. A nonlinearity is used to remove the MPSK modulation and generate the carrier component to be extracted. Theoretical and simulated performance results are presented and compared to the Cramer-Rao lower bound (CRLB) for the variance of the frequency estimation error. For all signal-to-noise ratios (SNR's) above threshold, it is shown that the CRLB can essentially be achieved with linear complexity.

Crozier, Stewart N.↗

NASA NTRS1987

Time-partitioning simulation models for calculation on parallel computers

A technique allowing time-staggered solution of partial differential equations is presented in this report. Using this technique, called time-partitioning, simulation execution speedup is proportional to the number of processors used because all processors operate simultaneously, with each updating of the solution grid at a different time point. The technique is limited by neither the number of processors available nor by the dimension of the solution grid. Time-partitioning was used to obtain the flow pattern through a cascade of airfoils, modeled by the Euler partial differential equations. An execution speedup factor of 1.77 was achieved using a two processor Cray X-MP/24 computer.

Milner, Edward J.↗

NASA NTRS1987

Time-partitioning simulation models for calculation of parallel computers

Milner, Edward J.↗

DOE OSTI2025

A generative artificial intelligence framework for long-time plasma turbulence simulations

Generative deep learning techniques are employed in a novel framework for the construction of surrogate models capturing the spatiotemporal dynamics of 2D plasma turbulence. The proposed Generative Artificial Intelligence Turbulence (GAIT) framework enables the acceleration of turbulence simulations for long-time transport studies. GAIT leverages a convolutional variational auto-encoder and a recurrent neural network to generate new turbulence data from existing simulations, extending the time horizon of transport studies with minimal computational cost. The application of the GAIT framework to plasma turbulence using the Hasegawa–Wakatani (HW) model is presented, evaluating its performance via various analyses. Very good agreement is found between the GAIT and the HW models in the spatiotemporal Fourier and Proper Orthogonal Decomposition spectra, the flow topology characterized by the Okubo–Weiss parameter, and the time autocorrelation function of turbulent fluctuations. Excellent agreement has also been obtained in the probability distribution function of particle displacements and the effective turbulent diffusivity. In-depth analyses of the latent space of turbulent states, choice of hyperparameters and alternative deep learning models for the time prediction are presented. Our results highlight the potential of Artificial Intelligence-based surrogate models to overcome the computational challenges in turbulence simulation, which can be extended to other situations such as geophysical fluid dynamics.

Artificial intelligence↗

DOE OSTI2020

Magnetic Navigation for GPS-Denied Airborne Applications

Most current flight systems are dependent on GPS for navigation. Recently, however, navigation in GPS-denied environments has become an area of intensive research. Additional navigation sensor data can be obtained from visual observations (stars or terrain), inertial measurement units, radar, measurements of the local magnetic field, or perhaps even gravity. Absolute and relative positioning via magnetic field measurements have been shown to be viable in many applications including ground navigation, low altitude aircraft flight, and spaceflight. There is greater variability in the magnetic field over shorter distances when flying at low altitude and in ground applications, leading to more accurate positioning. However, ground-based magnetic navigation is often heavily influenced by man-made structures, especially in urban environments. This is not the case for airborne magnetic navigation since the influence of buildings, roads, etc. is negligible for typical aircraft altitudes. For absolute magnetic navigation, the positioning accuracy decreases as altitude increases for a given vehicle velocity, but the observed time variability in the field can be reclaimed by traveling faster through the field. Thus, navigation accuracy becomes a balance of speed and altitude since the higher altitude can be counterbalanced by higher velocity. To understand these effects quantitatively, we explored various techniques to aid a simulated inertial measurement unit with magnetic information. Using a technique known as two-dimensional magnetic map matching, we simulated the performance of airborne magnetic navigation at fixed speed while varying the altitude, flight direction, magnetometer data collection time, reference magnetic map bias error, and type of trajectory (over land or over ocean).

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

NASA NTRS1984

Automated rendezvous and docking: A parametric study

A technique for achieving autonomous rendezvous and docking of two orbiting space vehicles is described. Results of a digital computer simulation of the technique are presented and used to evaluate its performance under a wide variety of conditions, including docking with tumbling spacecraft. The interrelationships between initial range, tumbling rates, fuel consumption, and time requirements are explored. Factors which limit performance are identified and beneficial modifications proposed.

Dabney, R.↗

NASA NTRS1993

Magnetic Compensation For Gravitational Pressure Gradient

In technique for partial simulation of low gravitation in diamagnetic or paramagnetic liquid, magnetic field having suitable gradient produces force counteracting gravitational force. Technique makes possible to perform low-gravity experiments on ground, at considerably less expense than in outer space.

Israelsson, Ulf E.↗

NASA NTRS2005

Investigation of the Carbon Arc Source as an AM0 Solar Simulator for Use in Characterizing Multi-Junction Solar Cells

The operation of multi-junction solar cells used for production of space power is critically dependent on the spectral irradiance of the illuminating light source. Unlike single-junction cells where the spectral irradiance of the simulator and computational techniques may be used to optimized cell designs, optimization of multi-junction solar cell designs requires a solar simulator with a spectral irradiance that closely matches AM0.

Xu, Jianzeng↗

NASA NTRS2005

Adventures in Parallel Processing: Entry, Descent and Landing Simulation for the Genesis and Stardust Missions

This paper will describe the Entry, Descent and Landing simulation tradeoffs and techniques that were used to provide the Monte Carlo data required to approve entry during a critical period just before entry of the Genesis Sample Return Capsule. The same techniques will be used again when Stardust returns on January 15, 2006. Only one hour was available for the simulation which propagated 2000 dispersed entry states to the ground. Creative simulation tradeoffs combined with parallel processing were needed to provide the landing footprint statistics that were an essential part of the Go/NoGo decision that authorized release of the Sample Return Capsule a few hours before entry.

Lyons, Daniel T.↗

NASA NTRS1990

Propulsion simulation for magnetically suspended wind tunnel models

The feasibility of simulating propulsion-induced aerodynamic effects on scaled aircraft models in wind tunnels employing Magnetic Suspension and Balance Systems. The investigation concerned itself with techniques of generating exhaust jets of appropriate characteristics. The objectives were to: (1) define thrust and mass flow requirements of jets; (2) evaluate techniques for generating propulsive gas within volume limitations imposed by magnetically-suspended models; (3) conduct simple diagnostic experiments for techniques involving new concepts; and (4) recommend experiments for demonstration of propulsion simulation techniques. Various techniques of generating exhaust jets of appropriate characteristics were evaluated on scaled aircraft models in wind tunnels with MSBS. Four concepts of remotely-operated propulsion simulators were examined. Three conceptual designs involving innovative adaptation of convenient technologies (compressed gas cylinders, liquid, and solid propellants) were developed. The fourth innovative concept, namely, the laser-assisted thruster, which can potentially simulate both inlet and exhaust flows, was found to require very high power levels for small thrust levels.

Joshi, Prakash B.↗

NASA NTRS2019

Assessing Reliability of NDE Flaw Detection Using Smaller Number of Demonstration Data Points

The paper provides an engineering analysis approach for assessing reliability of NDE flaw detection using smaller number of demonstration data points. It explores dependence of probability of detection (POD), probability of false positive (POF), on contrast-to-noise ratio, and net decision threshold-to-noise ratio in a simulated data; and draws some generically applicable inferences to devise the approach. ASTM nondestructive evaluation standards provide requirements on signal-to-noise ratio and/or contrast-to-noise ratio in order to provide reliable flaw detection and limit false positive calls. POD analysis of inspection test data results in an estimated flaw size, denoted by 𝑎90/95. This flaw size has 90% POD and minimum 95% confidence. POF is also estimated in the analysis. POD demonstration requires specimens with flaws of known size. In many situations, it is very expensive to produce the large number of flaws required for the POD analysis. In some situations, only real flaws can truly represent the flaws for demonstration. Real flaws of correct size and location in part configuration specimen may be difficult to produce, if not impossible. Here, an engineering analysis approach is devised using simulation to assess reliability of NDE technique when a limited number of flaws are available for demonstration. In this simulation, a technique is considered reliable, if it provides flaw detectability size equal to or better than the theoretical 𝑎90𝑡ℎ used in simulation and also provides a POF less than or equal to a chosen value. The paper uses simulated signal response versus flaw size data to devise the approach. Linear correlation is used between the signal response data and flaw size. POD software mh1823 uses generalized linear model (GLM) in POD analysis after transforming the flaw size and signal response, if needed, using logarithm. Therefore, this approach is in agreement with the linear signal correlation used in mh1823. Using the POD analysis of data, generic conditions on contrast-to-noise ratio and net decision threshold-to-noise ratio are derived for reliable flaw detection. In order to assess technique reliability using the engineering approach, signal response-to-flaw size correlation about the flaw size of concern is needed. In addition, measurement of noise is also needed. If the technique meets the above requirements, assumption of linear signal-to-flaw size correlation and conditions on noise, then the technique can be assessed using this analysis as it fits the underlying POD model used here. The approach is conservative and is designed to provide a larger flaw size compared to the POD approach. Such NDE technique assessment approach, although, not as rigorous as POD, can be cost effective if the larger flaw size can be tolerated. Typically, this is a situation for all quality control NDE inspections. Here, an NDE technique needs to be reliable and 𝑎90/95 is not estimated, but the assessed flaw size is assumed to be larger than the unknown a90 due to conservative factors or margins. Applicability of the approach for assessing reliability of flaw detection in x-ray radiography and 2D imaging in general is also explored.

Koshti, Ajay M.↗

NASA NTRSDate not supplied

Ab-Initio Study of Stacking Fault Segregation Behavior in Ni-based Superalloys at High Temperatures

Ni-based superalloys demonstrate extraordinary creep properties compared to traditional metallic systems due to the formation of L12 (γ’) precipitates. Despite experimental evidence of alloying element segregation to the stacking faults, prior ab-initio efforts indicated repulsion of Nb from superlattice intrinsic stacking faults (SISFs) . Due to the importance of this element in key strengthening mechanisms, we developed a new technique to account for multi-component segregation behavior at temperature combining ab-initio molecular dynamics (AIMD) and Monte-Carlo (MC) simulations. Using this technique, we replicated experimentally observed segregation behavior of Nb, Co, and Ti to the SISF in L12 (Figure 1). Furthermore, we investigated the co-segregation behaviors of individual pairs of alloying elements to determine the interaction effects which lead to this segregation behavior in the full alloy system. By simulating the reduced-chemistry models using our approach, we reconciled previous ab-initio calculations demonstrating repulsion of Nb from the SISF and the experimentally observed segregation behavior.

Molecular Dynamics↗

DOE OSTI2018

Benchmarking treewidth as a practical component of tensor network simulations

Tensor networks are powerful factorization techniques which reduce resource requirements for numerically simulating principal quantum many-body systems and algorithms. The computational complexity of a tensor network simulation depends on the tensor ranks and the order in which they are contracted. Unfortunately, computing optimal contraction sequences (orderings) in general is known to be a computationally difficult (NP-complete) task. In 2005, Markov and Shi showed that optimal contraction sequences correspond to optimal (minimum width) tree decompositions of a tensor network’s line graph, relating the contraction sequence problem to a rich literature in structural graph theory. While treewidth-based methods have largely been ignored in favor of dataset-specific algorithms in the prior tensor networks literature, we demonstrate their practical relevance for problems arising from two distinct methods used in quantum simulation: multi-scale entanglement renormalization ansatz (MERA) datasets and quantum circuits generated by the quantum approximate optimization algorithm (QAOA). We exhibit multiple regimes where treewidth-based algorithms outperform domain-specific algorithms, while demonstrating that the optimal choice of algorithm has a complex dependence on the network density, expected contraction complexity, and user run time requirements. We further provide an open source software framework designed with an emphasis on accessibility and extendability, enabling replicable experimental evaluations and future exploration of competing methods by practitioners.

97 MATHEMATICS AND COMPUTING↗

NASA NTRS1990

Direct simulation of hypersonic rarefied flow about a delta wing

Three-dimensional hypersonic rarefied flow about a delta wing at angle of incidence has been studied using the direct simulation Monte Carlo technique. Results are obtained for a transitional flow case which has been investigated in a nitrogen wind-tunnel experiment. The simulations are performed using a nonreacting, single-species gas model that accounts for rotational and vibrational internal energies. The computations yield an attached leeside flow associated with supersonic expansion over the leeside of the wing. Results are presented for the computed flowfield and surface quantities and overall aerodynamic coefficients.

Celenligil, M. Cevdet↗

NASA NTRS1990

Statistical interference prediction for ground stations from orbiting satellites. I - Simulation of interference duration and analytical approach for the determination of protection ratios

The authors describe simulation and analytical techniques for predicting the interference durations and protection ratios for deep-space ground stations from satellites in circular orbits. The simulation approach employs the characteristics of the ground station receivers in addition to the satellite specifications to calculate the daily statistics of the interference duration. On the other hand, the analytical method employs the ground station specifications to statistically predict the protection ratios as a function of the number of interference satellites and their associated probabilities. The results presented here can be used for both planning the missions and designing satellite communication links. The results can be also be used by spectrum managers and operations personnel to minimize the risk of harmful interference from satellites in low earth orbit to the deep space frequency band.

Gevargiz, John M.↗

NASA NTRS1992

Procedure for Adapting Direct Simulation Monte Carlo Meshes

A technique is presented for adapting computational meshes used in the G2 version of the direct simulation Monte Carlo method. The physical ideas underlying the technique are discussed, and adaptation formulas are developed for use on solutions generated from an initial mesh. The effect of statistical scatter on adaptation is addressed, and results demonstrate the ability of this technique to achieve more accurate results without increasing necessary computational resources.

Woronowicz, Michael S.↗

DOE OSTI2025

New electric force and charge exchange modules in discrete element model enables particle dynamics simulation in electric field

Discrete element modeling (DEM) is an important technique for particle dynamics simulation. The field of metal additive manufacturing often utilizes DEM to simulate the rheological behaviors of powder. Standard contact and short-range interactions are sufficient in most cases but insufficient to describe the particle dynamics with the influence of an electric field. Modeling such a system requires additional physics to describe the particle–field interactions. The relevant physics has been experimentally understood but is not yet available in DEM. Here, we develop a charge exchange and an electric force module. The electric force module governs particle response to the electric field, while the charge exchange module enables particles to acquire proper charge during contact with charged geometries. We validate the modules against analytical calculations and high-speed videos of electrostatic powder deposition experiments. Notably, the model struggles to capture the initial particle levitation. We later deploy a modified electric field, as supported by static electric field simulation, to better approximate the electric field penetration into the powder layer. This modification improves the model’s capability of simulating realistic particle levitation. The results highlight the challenges of modeling particle behaviors in the electric field while demonstrating the feasibility of obtaining quantitative results, which are difficult to measure experimentally.

charge exchange↗

NASA NTRS1974

High power ac/dc variable R dynamic electrical load simulator

A study program was undertaken to investigate various concepts and techniques for identifying and simulating both the steady-state and dynamic characteristics of electrical loads for use during integrated system test and evaluation. The development of hardware capable of providing the simulation capability is discussed. A general purpose simulator was developed with the capability of realizing a variety of models where element values were discretely variable. The different models, each corresponding to real spacecraft equipment, are set up manually for each case by suitable switching and patching. The models are capable of duplicating the dynamic and steady-state response of real loads at full power.

Joncas, K. P.↗