Search NASA⌕ Search

SEARCH · Search NASA

Results for “Binder”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Binder-Stabilized Carbon Fiber Hosts for High-Utilization Sodium–Polysulfide Flow Catholytes

Sodium-sulfur (Na-S) batteries hold promise as high-energy-density batteries for long-duration energy storage due to their high open circuit voltage and Earth-abundant active materials. However, low utilization of the sulfur active material limits the achievable specific capacity, especially when a liquid polysulfide catholyte is utilized. High-surface-area carbon materials demonstrate promise to increase sulfur utilization in a Na-S battery. To make the carbon host material applicable for a flow battery application, a binder is required to bind the carbon materials together and to a porous substrate. Here, we utilize a composite carbon paper electrode coated by polymer,carbon nanofibers (CNFs) and carbon black (CB). By varying the mass ratios of CNF to CB, we found that a 70/20/10 mass ratio of CNF/CB/binder provided the highest capacity (260 mAh g −1 compared to the baseline of 156 mAh g −1 ) and stable battery performance over 100 cycles. Analysis of the composite electrode and full cells reveals that the amount of CB in the composite electrode influences binder distribution, cell resistance, and full cell performance.

Lehmann, Michelle L. [Oak Ridge National Laborator↗
DOE OSTI2025

Binder-benchmarking

SAND2025-07593O Binder-benchmarking evaluates the speed and memory impacts of C++, Python, and Matlab code binders. As a repository, it provides a way to locally run computation-based and memory-based benchmark suites on pybind11 and nanobind-based code in a Docker image. The software runs simple-speed and memory benchmarks on primitive navigation and integration exemplar algorithms. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525.

Walker II, Michael [Sandia National Lab. (SNL-CA),↗
DOE OSTI2022

Scoping studies for low-temperature melting ZnO–Bi 2 O 3 –(B 2 O 3 , SiO 2 ) binder glass

In this work, low melting point glass systems were explored as candidates for binders of solid oxide nuclear wastes which include volatile elements such as radioactive iodine. The base glass systems considered were ZnO-Bi 2 O 3 -B 2 O 3 and ZnO-Bi 2 O 3 -SiO 2 , with specific compositions selected for synthesis trials based on available phase diagrams and a desire to explore the whole glass-forming region. Ten compositions were synthesized by melt quenching. Promising candidate glass binders were selected based on absence of crystallization and favorable thermal properties, including low glass transition temperature (T g ) combined with a high crystallization onset temperature. These thermal properties indicate stable glass forming which would lead to sintering behavior needed for glass binding. Compositional effects include: higher Bi 2 O 3 content lead to lower Tg values, high ZnO content generally led to crystallization on quench, and high SiO 2 content resulted in requirements for excessively high melting temperature. 25ZnO-15Bi 2 O 3 -60B 2 O 3 was down-selected for some detailed crystallization versus time and temperature studies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Functional polymer binder for sulfur cathode fabrication

The present invention provides for a composition of matter, polymeric conductive binder, or electrode comprising: Poly[(2-ethyldimethylammonioethyl methacrylate ethyl sulfate)-co-(1-vinylpyrrolidone)]. The present invention also provides for a Lithium-Sulfur (Li—S) battery comprising a cathode comprising: a cathode comprising a polymeric conductive binder poly[(2-ethyldimethylammonioethyl methacrylate ethyl sulfate)-co-(1-vinylpyrrolidone)]; a separator; an anode; and, an electrolyte.

25 ENERGY STORAGE↗
DOE OSTI2020

Lithium-sulfur battery with polyanthraquinone binder

A cathode for a lithium-sulfur (Li—S) battery is described herein, which comprises elemental sulfur (e.g., S8) and an electroactive polyanthraquinone-containing binder. In some embodiments, the cathode also includes a conductive carbon material in addition to the sulfur and binder. Also described herein is a Li—S battery comprising the cathode, in combination with a metallic lithium-containing anode, a lithium conductive separator membrane between the anode and the cathode, and a liquid electrolyte comprising a lithium salt dissolved in a non-aqueous organic solvent.

25 ENERGY STORAGE↗
DOE OSTI2021

Actinic and electron beam radiation curable water based electrode binders and electrodes incorporating same

A process for manufacturing an electrode utilizing electron beam (EB) or actinic radiation to cure the electrode binder is provided. A process is also disclosed for mixing specific actinic or EB radiation curable polymer precursors with electrode solid particles to form an aqueous mixture, application of the mixture to an electrode current collector, followed by the application of actinic or EB radiation to the current collector for curing the polymer, thereby binding the electrode binder to the current collector. Lithium ion batteries, electric double layer capacitors, and components produced therefrom are also provided.

Voelker, Gary E.↗
DOE OSTI2022

Heat treatable magnets having improved alignment through application of external magnetic field during binder-assisted molding

Improved manufacturing processes and resulting anisotropic permanent magnets, such as for example alnico permanent magnets, having highly controlled and aligned microstructure in the solid state are provided. A certain process embodiment involves applying a particular orientation and strength of magnetic field to loose, binder-coated magnet alloy powder particles in a compact-forming device as they are being formed into a compact in order to preferentially align the magnet alloy powder particles in the compact. The preferential alignment of the magnet alloy powder particle is locked in place in the compact by the binder after compact forming is complete. After removal from the device, the compact can be subjected to a subsequent sintering or other heat treating operation.

Kassen, Aaron G.↗
DOE OSTI2022

Multi-scale characterization of supersolidus liquid phase sintered H13 tool steel manufactured via binder jet additive manufacturing

Additive manufacturing (AM) of H13 tool steel by binder jet 3D printing (BJ3DP) followed by pressureless supersolidus liquid phase sintering (SLPS) provides a low-cost alternative manufacturing method for components with intricate geometric features. However, the microstructure-mechanical property relationships for BJ3DP-SLPS produced H13 tool steel are not well understood, which makes it challenging to develop printing and post-processing methods that maximize part performance. In this work, we leverage atom probe tomography and transmission electron microscopy along with thermodynamic calculations to rationalize the microstructure-mechanical property relationships in as-sintered BJ3DP H13 tool steel. Here, we report for the first time, the presence of a continuous eutectic film-like carbide in H13 along with the more commonly observed cuboidal MX carbides in the prior liquid channels of the microstructure. Further, atom probe tomography revealed the interconnected nature of the MX carbides that appear to be discrete in two-dimensional micrographs. These continuous eutectic carbides and interconnected MX carbides result in brittle failure of the material. Characterization of these microstructural features will be critical in developing appropriate post-processing heat treatments for the improved mechanical performance of BJ3DP H13.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Binder-Free Wood Converted Carbon for Enhanced Water Desalination Performance

Here, the design and synthesis of high-performance and economical carbon electrodes play a critical role in developing energy-efficient water desalination technologies. As a sustainable approach, low-cost and abundant biomass materials are promising candidates to prepare porous carbon for capacitive deionization. In this study, binder-free porous carbon sheets are successfully prepared using natural balsa, pine, and basswood by thermal carbonization and treated by chemical activation. The carbon electrode materials converted from balsa and pine exhibit a comparable salt adsorption performance by capacitive deionization due to the extensive surface area, substantial electrical property, and superior hydrophilic performance. The following activation treatment of the balsa-converted carbon further enhances the surface and electrical properties and benefits the desalination performance. The salt adsorption capacity of the activated balsa electrode exhibits 12.45 mg g -1 . Additionally, 19.52 mg g -1 Pb 2+ and 20.06 mg g -1 Cr 3+ heavy metal adsorption capacity is also observed with the activated balsa electrode in 100 mg L -1 PbCl 2 and 50 mg L -1 CrCl 3 , respectively. To the best of authors’ knowledge, this is the highest NaCl adsorption capacity performance reported thus far by using pure wood converted carbon as the electrode, and these promising results indicate that activated balsa is an extraordinary material for water desalination.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Amphipathic Binder Integrating Ultrathin and Highly Ion-Conductive Sulfide Membrane for Cell-Level High-Energy-Density All-Solid-State Batteries

Current sulfide solid-state electrolyte (SE) membranes utilized in all-solid-state lithium batteries (ASLBs) have a high thickness (0.5–1.0 mm) and low ion conductance (<25 mS), which limit the cell-level energy and power densities. Therefore, based on ethyl cellulose's unique amphipathic molecular structure, superior thermal stability, and excellent binding capability, this work fabricates a freestanding SE membrane with an ultralow thickness of 47 µm. With ethyl cellulose as an effective disperser and a binder, the Li 6 PS 5 Cl is uniformly dispersed in toluene and possesses superior film formability. In addition, an ultralow areal resistance of 4.32 Ω cm -2 and a remarkable ion conductance of 291 mS (one order higher than the state-of-the-art sulfide SE membrane) are achieved. The ASLBs assembled with this SE membrane deliver cell-level high gravimetric and volumetric energy densities of 175 Wh kg -1 and 675 Wh L -1 , individually.

25 ENERGY STORAGE↗
DOE OSTI2020

Processing and properties of SiC composites made via binder jet 3D printing and infiltration and pyrolysis of preceramic polymer

The effect of polymer infiltration and pyrolysis (PIP) cycles with polycarbosiloxane on the microstructure, air leak rate, and properties of SiC composites manufactured by a combination of binder jet 3D printing and PIP are reported. The density, Young’s modulus and flexural strength of disk-shaped components increased with the number of PIP cycles. In the case of density, it increased from 2.05 g/cm 3 in one PIP cycle to 2.33 g/cm 3 after three PIP cycles, while values of flexural strength and Young’s modulus at room temperature after three PIP cycles reached 66.8 ± 2.5 MPa and 69.5 ± 2.8 GPa, respectively. Conversely, the air leak rate was found to decrease with number of PIP cycles, and it reached a value of 4 mbar-liter/s after three cycles. The instantaneous coefficient of thermal expansion of the composite was found to change minimally with the number of PIP cycles and had a value of 4 ± 1.2 ppm/°C between 200°C and 1,000°C. Thermal conductivity was found to increase with number of PIP cycles and to decrease with temperature. For example, after 3 PIP cycles it was found to change from 6.72 ± 0.08 to 6.98 ± 0.08 W/mK at 25°C and 7.36 ± 0.08 to 7.96 ± 0.08 W/mK at 300°C. These values were lower than those of crystalline SiC because of the amorphous nature of the matrix and the presence of pores and cracks.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Revealing the working mechanism of a multi-functional block copolymer binder for lithium-sulfur batteries

The lithium-sulfur (Li-S) battery is one of the most promising substitutes for current energy storage systems because of its low cost, high theoretical capacity, and high energy density. However, the high solubility of intermediate products (i.e., lithium polysulfides) and the resultant shuttle effect lead to rapidly fading capacity and a low coulombic efficiency, which hinder the practical application of Li-S batteries. In this study, block copolymers are constructed with both an ethylene oxide unit and a styrene unit and then used as binders for Li-S batteries. Electrochemical performance improvements are attributed to the synergistic effects contributed by the different units of the block copolymer. Here, the ethylene oxide unit traps polysulfide, which bonds strongly with the intermediate lithium polysulfide, and enhances the transport of lithium ions to reach high capacity. Meanwhile, the styrene unit maintains cathode integrity by improving the mechanical properties and elasticity of the constructed block copolymer to accommodate the large volume changes. By enabling multiple functions via different units in the polymer chain, high sulfur utilization is achieved, polysulfide diffusion is confined, and the shuttle effect is suppressed during the cycle life of Li-S batteries, as revealed by operando ultraviolet–visible spectroscopy and S K-edge X-ray absorption spectroscopy.

25 ENERGY STORAGE↗
DOE OSTI2025

Optimization of overhang printing in ceramic binder jetting additive manufacturing

Cylindrical-shaped horizontally-hanging overhangs with different heights on a solid cubic body were printed via binder jetting additive manufacturing with sililcon carbide powder feedstock. Cracking on the overhang neck and sagging on the overhang body were observed both pre- and post-curing, especially on printed design with a smaller particle size of 10 μm. Here, it was found that the width of cracking and depth of sagging were dependent on the height relative to the solid body in the powder bed, and elevated position of overhang with large volume of underneath loose powder led to increased extend of cracking and sagging. Overhang diameter and weight were varied, which were found with no apparent effects on its deformation extend. To mitigate cracking and sagging, contactless support was designed and tested, which could significantly improve the overhang stability and avoid any overhang deformations. Support gap and support distance were studied for their effects on support capability. The printing processes with and without contactless support were simulated by a finite element modeling approach to understand the stress distribution and evolution of the overhang structures, which revealed stress concentrations on the upper neck point of the designed overhang.

Binder jetting↗
DOE OSTI2025

High temperature tensile properties of H13 tool steel fabricated via binder jet additive manufacturing

H13 is one of the most used steels for hot work tooling applications like die casting. Binder jet additive manufacturing (BJAM) offers a cost-effective solution to fabricate tools with performance enhancing features like internal cooling channels. While full densification of BJAM H13 has been demonstrated in the literature, the room and high temperature tensile properties of the material, and the effect of post-process treatments like hot isostatic pressing (HIP), and heat treatment (HT) are unknown. Here we use HIP+HT to obtain a combination of ultimate tensile strength (UTS) and elongation to failure that is superior to H13 fabricated via laser powder bed fusion and wire arc additive manufacturing. HIP+HT BJAM H13 has a superior UTS (1836 MPa) compared with conventionally processed (1671 MPa) H13 but has lower plastic elongation. We report that as-sintered samples have an extensive network of continuous grain boundary (GB) carbides that contribute to brittle fracture. HIP+HT results in partial dissolution of GB carbides and formation of a fine martensitic microstructure resulting in superior tensile strength and elongation compared with as-sintered H13. We use thermo-kinetic calculations to rationalize the effects of HIP+HT on microstructure and properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Development of a high-temperature Inconel 625 heat exchanger by model design and binder jetting additive manufacturing

A nickel-based Inconel 625 superalloy heat exchanger for high-temperature applications was developed via binder jetting additive manufacturing. The material properties were characterized first on printed and sintered parts. Two sintering temperatures were used to investigate the effects of the temperature on densification and microstructure. For channel geometry design, the heat transfer capabilities of the heat exchanger were optimized for the cross-section geometry of fluid flow channels in a counterflow configuration, and a stress analysis was conducted to investigate the effects of channel geometry. After headers were incorporated into the heat exchanger as a one-piece component, a prototype was printed. A complete depowdering was achieved via compressed air blowing, and sintering was performed with the developed profile. Ultimately, a one-piece heat exchanger with a nearly full density was obtained. Heat transfer tests were performed on this unit, and the results were compared with those from the simulations. In this study, systematic processes were developed for an additively manufactured Inconel-based heat exchanger for high-pressure, high-temperature heat transfer applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Influence of microstructure and temperature on impact toughness of H13 steel produced by binder jet additive manufacturing

Binder Jet Additive Manufacturing (BJAM) is a promising manufacturing pathway to produce H13 steel dies and tooling with complex geometries for applications in high pressure aluminum die casting, hot stamping, and injection molding. While fully dense H13 coupons produced using BJAM have been subjected to detailed microstructure characterization, properties which are critical and relevant to the aforementioned applications, such as impact toughness, have not been reported. Here, this work evaluated the influence of microstructural characteristics and test temperature on the impact toughness of H13 produced by BJAM. Coupons were produced from three different powder size distributions (PSDs), with nominal powder size ranges of −22 μm, 10-32 μm, and 15-53 μm. Coupons were printed, sintered, hot isostatically pressed (HIPed), and heat treated by quenching and tempering. After HIPing, the measured porosities of the different PSDs were all less than 0.015 vol%. The −22 μm PSD BJAM material exhibited the best impact toughness of all three PSDs across the entire test temperature range from 25 to 400 °C, and also exhibited an ambient temperature impact toughness of 10.9 J at a hardness of 46 HRC, equivalent to minimum threshold requirements for premium grade H13. However, all three BJAM PSDs exhibited moderately lower impact toughness than premium grade wrought H13 from RT to 400 °C. We attribute this in part due to the very large prior-austenite grain (PAG) sizes near 400 μm and segregation from former liquid channels leading to greater amounts of carbide precipitation on PAG boundaries. Technical pathways for optimizing processing and chemistry of BJAM H13 to further improve impact toughness are discussed.

Binder jet additive manufacturing↗
DOE OSTI2024

Design of robot grippers for binder jet products handling

Dimension accuracy, damage minimization, and defect detection are essential in manufacturing processes, especially additive manufacturing. These types of challenges may arise either during the manufacture of a product or its use. The repeatability of the process is vital in additive manufacturing systems. However, human users may lose concentration and, thus, would be a great alternative as an assistant. Depending on the nature of work, a robot’s fingers might vary, for example, mechanical, electrical, vacuum, two-fingers, and three-fingers. In addition, the end effector plays a vital role in picking up an object in the advanced manufacturing process. However, inbuilt robotic fingers may not be appropriate in different production environments. In this research presented here considering metal binder jet additive manufacturing, the two-finger end- effectors are proposed design, analysis, and experiment to pick up an object after completing the production process from a specific location. The final designs were further printed by using a 3D metal printer and installed in the existing robotic systems. These new designs are used successfully to hold the object from the specific location by reducing the contact force that was not possible with the previously installed end effector's finger. In addition, a numerical study was conducted in order to compare the flowability of the geometric shape of finger's free areas.

42 ENGINEERING↗
DOE OSTI2025

Preliminary hyperspectral neutron radiography of binder jet 3D printed and melt infiltrated Si–SiC

The preliminary results of hyperspectral neutron radiography of Si–SiC made with binder jet additive manufacturing, subsequent carbon addition, and silicon melt infiltration are presented. The samples were measured in the processing states before and after the melt infiltration to determine if neutrons would help characterize the microstructure to better understand the melt infiltration process. Theoretical Bragg edges were calculated for comparison with the radiographic results. The changes in the Bragg edges from pre- to post-infiltrated reaction-bonded SiC were evident, that could be used to address the differences in microstructures. In conclusion, the preliminary results presented in this study demonstrated that neutron Bragg-edge imaging is possible with Si–SiC reaction-bonded ceramics and can help determine the microstructure of melt infiltrated samples.

SiC↗