Microelectronic Structure and Doping Nonuniformity of Phosphorus-Doped CdSeTe Solar Cells
Not Available
14 SOLAR ENERGY↗
SEARCH · Search NASA
Results for “CdTe solar cell”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Nanometer-scale electrical potential imaging on absorber of CdSeTe solar cells
Here, we report on nm-scale electrical potential imaging throughout As-doped and Cu-doped CdSeTe absorbers using Kelvin probe force microscopy (KPFM). The potential imaging was conducted both laterally and vertically on beveled films using ion milling at small glancing angle. KPFM images electrical potential on the beveled surface and assesses defect charging in the subsurface region within a screening length from the beveled surface. We found that the grain boundaries were positively charged and that there were significant potential fluctuations in both grain boundary versus grain interior and intragrain. We further found that these potential fluctuations decreased significantly toward the front interface. Time of flight secondary ion mass spectrometry imaging shows that Se content increased toward the front interface, consistent with Se passivation of defects. The potential fluctuation was induced by defect charging, and the results elucidate different details of the defect configurations and grain structures of the films with different CdCl 2 treatment temperatures in the As-doped CdSeTe. The defect configurations in the region near the front interface can be a main factor contributing to the device performance difference. Our potential imaging provides insights about the defects throughout the absorber films, and shows that the potential fluctuation has a direct correlation to the V oc deficit.
14 SOLAR ENERGY↗
Imaging Power Losses in CdSeTe Solar Cells
Much of the research on CdSeTe photovoltaics is focused on improving the open-circuit voltage (V oc ) of the solar cell. But solar cells operate at the maximum power point (MPP) rather than at V oc . The recombination processes at MPP may be different than those at V oc , and increasing the power output at MPP is the key to advancing efficiency. Here, we introduce a camera-based PL imaging system that enables power loss analysis under operating conditions and across cm-sized areas covering multiple cells. The instrument is demonstrated with CdSeTe devices having efficiencies greater than 19%. An implied current density versus implied voltage (iJV) curve can be produced at each pixel with <20 µm resolution. We find that regions with high implied open circuit voltage are often those with low implied fill factor, showing that voltage loss analysis at open circuit is not sufficient to understand power losses under operating conditions. Measurement of JV curves as a function of irradiance can also be performed in the system, which allows series resistance-free pseudo JV (pJV) curves to be produced. Comparison of pJV to measured JV and iJV curves allows further analysis of the operational losses, pointing the way to higher efficiency.
14 SOLAR ENERGY↗
Atomistic modeling of energy band alignment in CdSeTe surfaces
Atomistic modeling based on Desnity Functional Theory (DFT)- 1/2 method coupled with surface Green’s function has been employed to investigate the energy band alignment results in cadmium selenium telluride (CdSeTe) surfaces. The structural and electronic properties of the bulk ternary alloy were established before cleaving the CdSeTe low index surface facets. The dependency of atomic-scale electronic features on different plane orientations was explored by studying the energy band alignment diagrams in the unreconstructed and reconstructed surfaces. While the low index CdSeTe surface geometry reconstructions replicate the CdTe surface geometries, the energy band alignment features of the unreconstructed and reconstructed CdSeTe surfaces differ from those observed in CdTe low index surfaces. The structurally relaxed reconstructed CdSeTe surface results in purely flat bands as opposed to an internal cusp feature observed in CdTe surfaces. The presence of an internal energy cusp in CdTe(111) surfaces is expected to play a key role in enhancing the hole charge transport towards the back of CdTe-only solar cell device and the absence of such feature in CdSeTe surface may explain one of the reason for the lower performance of CdSeTe-only solar cell seen experimentally.
36 MATERIALS SCIENCE↗
Imaging hole-density inhomogeneity in arsenic-doped CdTe thin films by scanning capacitance microscopy
We report nanometer-scale hole-density imaging in As-doped CdTe films by scanning capacitance microscopy (SCM). The hole-density profiling is validated by contrasting a CdTe cross-section sample made by molecular-beam epitaxy with systematically increased As doping in a staircase pattern over the range of 10 15 -10 18 /cm 3 within a single film. In polycrystalline films, the carrier distribution is significantly nonuniform, with inhomogeneity ranging from several hundred nm to several um and hole density varying by one order of magnitude (low 10^16 to low 10 17 /cm 3 ). This nonuniformity is distributed randomly, independent of the grain structure and grain boundaries (GBs). Kelvin probe force microscopy (KPFM) maps the surface potential and is correlated to cathodoluminescence (CL) and SCM by imaging over identical areas. Higher potential and lower CL intensity are found on GBs but not by SCM contrast; this indicates positive GB charging and recombination, but not GB-specific hole-density changes. The overall KPFM potential image is in rough agreement with the SCM carrier distribution and indicates band-edge potential fluctuations. Nonuniform carrier concentration, potential fluctuations, and defect recombination can all cause voltage and performance loss in As-doped CdTe solar technology.
14 SOLAR ENERGY↗
The effect of remnant CdSe layers on the performance of CdSeTe/CdTe photovoltaic devices
Thin film CdTe-based photovoltaic devices have achieved high efficiency above 22 %. The recent improvement in efficiency is due to Se alloying in the CdTe absorbers to form a CdSeTe/CdTe structure. The subsequent band gap grading increases the short circuit current density. The Se can be introduced by depositing a precursor thin film of either CdSe or a CdSeTe alloy and then diffusing the Se into the CdTe during the high temperature cadmium chloride activation process. Using CdSe is preferred because it is easier to control the Se concentration. However, during fabrication of the CdSeTe/CdTe devices, the CdSe thickness needs to be precisely controlled to prevent the retention of a CdSe remnant layer after the activation treatment. Retention of a remnant CdSe layer causes a dramatic reduction in device efficiency. In this work, we show that the reduction in efficiency is caused by a number of factors. The remnant CdSe layer is n-type which moves the position of the p-n junction. Also, it is widely thought that the CdSe remnants are photo-inactive. In this work, we clarify that the individual CdSe grains are actually highly photo-active. However, the grain sizes in the CdSe remnant and the adjacent CdSeTe layer are very small resulting in a high grain boundary area. Although the grain boundaries are passivated with chlorine, cathodoluminescence imaging and electrical measurements show that this is only partially effective. Also, EQE measurements show that the remnant CdSe causes parasitic absorption. Overall, the remnant CdSe layer causes a reduction in short circuit current density and device efficiency. The thickness of the CdSe precursor layer and the cadmium chloride activation process conditions must be precisely optimised to ensure that all the CdSe is consumed and inter-diffused to form the CdSeTe alloy for highest efficiency devices.
CdSe remnant↗
Tellurium Goes for a Ride on the “Ferrous” Wheel: Interactions of Te(VI) and Te(IV) with Fe(II)-Bearing Minerals
Compared to more abundant metalloids (e.g., As, Se, and Sb), little is known regarding the biogeochemistry of tellurium (Te), a critical metal whose use in CdTe photovoltaic solar cells is driving increasing global demand for this element. In this study, to understand the redox behavior of Te under ferrugenic/sulfidogenic conditions, we examined the potential for reduction of Te(VI) and Te(IV) in aqueous suspensions containing Fe(II) as siderite, vivianite, green rust, magnetite, or mackinawite; Fe(II)-bearing minerals which are often formed during microbial reduction of Fe(III) oxides. In the mackinawite systems, complete reduction of Te(VI) or Te(IV) to Te(0) was observed within 12 h, and near complete reduction (>90% Te(0)) was observed within 2.5 days in the green rust systems. In the presence of siderite, complete reduction of Te(VI) or Te(IV) to Te(0) occurred within 60 days. We observed >60% reduction of Te(VI) to Te(IV) within 2.5 days in the magnetite system, but Te(0) did not form until 120 days; however, complete reduction to Te(0) was observed within 120 days when starting with Te(IV). With vivianite there was >80% reduction of Te(VI) to Te(IV) within 12 h, without further reduction to Te(0) over the duration of the experiment (120 days); in the Te(IV)-vivianite system, there was no evidence of Te(IV) reduction within 120 days. The reduction of Te(VI) and Te(IV) in soils and sediments has been largely attributed to direct reduction by microbes; however, the reduction of Te(VI) and Te(IV) by Fe(II)-bearing minerals suggests that abiotic or coupled biotic-abiotic processes may also play a critical role in Te redox chemistry in natural and engineered environments.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Mechanisms for long carrier lifetime in Cd(Se)Te double heterostructures
II–VI semiconductors are used in numerous electro-optical applications. For example, CdTe-based solar technology is cost competitive with other electricity generation sources, yet there is still significant room to improve. Carrier lifetime has historically been well below the radiative recombination limit. Lifetimes reaching beyond 100 ns can significantly enhance performance and enable novel device structures. Here, double heterostructures (DHs) with passivated interfaces demonstrate lifetimes exceeding 1 µs, yet this appears only for CdSeTe and not for CdTe DHs. We compare the passivation mechanisms in CdTe and CdSeTe DHs. CdSeTe lifetimes on the order of 1 µs correspond to a combination of superior intragrain lifetime, extremely low grain boundary recombination and greater Te4+ interfacial presence compared to CdTe.
36 MATERIALS SCIENCE↗
Proton radiation resilience of CdSeTe photovoltaics: High predicted end-of-life performance for space applications
Two types of cadmium selenide telluride (CdSeTe) photovoltaic devices have been exposed to high-energy (150–1500 keV) protons with fluences ranging from 1 × 10 11 to 9 × 10 13 cm −2 . Pre- and post-irradiation current density vs voltage characteristic data were collected and analyzed. Arsenic-doped CdSeTe devices retained 80% of the power conversion efficiency (PCE) relative to control devices after exposure to 10 12 cm −2 650 keV protons, while copper-doped CdSeTe devices retained about 95% of the control PCE under the same irradiation condition. Displacement damage dose analysis coupled with simulations for duration-dependent performance in a medium Earth orbit space mission revealed superior PCE remaining factors, indicating greater resilience to proton bombardment than state-of-the-art multijunction III-V based space photovoltaic technologies.
CdTe solar cells↗
Controlled thermomechanical delamination of thin films
Disclosed herein are CdTe-based solar cells that are successfully removed from their glass superstrate through a combination of lamination to a backsheet followed by thermal shock.
Reese, Matthew Owen↗
Doping of CdTe Using CuCl2 Solution for Highly Efficient Photovoltaic Devices
Here, we report doping of cadmium telluride (CdTe) thin film solar cells using copper (II) chloride (CuCl 2 ) solution in deionized water. The CdTe thin films were immersed in 0.1 mmol CuCl 2 solution in water and annealed in the temperature range of 180-240 degrees C for various time durations. The devices were completed using thermally evaporated gold (Au) and measured under simulated AM1.5G spectrum. The average device efficiency of CuCl 2 treated CdTe devices increased to 13.7 % (best cell reaching 14.0%) with significant improvement on open-circuit voltage (VOC ) as compared with 12.4% (best cell 12.7%) for thermally evaporated Cu doped CdTe devices. For CuCl 2 treated CdTe devices, we found higher photoluminescence (PL) intensity and longer carrier life time at room temperature indicating solution based doping offers better control of Cu doping density as compared with evaporated Cu.
14 SOLAR ENERGY↗
The role of native defects and their diffusivity in CdTe
CdTe is a leading thin-film technology for solar-cell applications. Basic features such as the optimum band gap of 1.5 eV and simple manufacturing process have been driving the research on improving the current record efficiency of 22% for CdTe solar cells toward the theoretical limit of 32%. Low p-type doping and short carrier lifetimes in the CdTe absorber have been suggested as the main limiting factors and attributed to defect compensation and carrier recombination. Understanding the role of point defects and impurities in CdTe is crucial to solving these problems. Despite many years of research, the sources of compensation and the microscopic recombination mechanisms are still unclear. By using hybrid density functional calculations with spin-orbit coupling and large supercells, we investigate the electronic properties, the formation energies, and the diffusivities of the native defects in CdTe. As possible sources of compensation for p-type conductivity, we discuss the structural and electronic properties of Cd interstitial, Te vacancies, and TeCd antisites. The stability of each defect is discussed in terms of both the defect formation energy and the migration barrier. We also address possible mechanisms that lead to non-radiative recombination.
14 SOLAR ENERGY↗
Oxides related to cadmium telluride solar cells
Polycrystalline cadmium telluride (CdTe) is a leading material in photovoltaic technology due to its high absorption coefficient and near-optimum bandgap of 1.44 eV. It is known that CdTe film processing can promote surface oxidation depending on the growth environment and upon exposure to different oxidation conditions. For example, CdTeO3 forms when the CdTe film is treated in heated dry air, while in humid air, CdTe2O5 is detected. These oxides feature tellurium in the oxidation state +4 compared to the +2 state in CdTe. Other possible relevant oxides are CdO, TeO2, and TeO3. Using hybrid density functional calculations, we studied the electronic structure of these oxide materials and their band alignment to CdTe, which are essential parameters in the characterization of the interfaces at grain boundaries. The goal is to understand their stability and possible effects on passivating grain boundaries. The results are compared to the available experimental data.
14 SOLAR ENERGY↗
Is 3D/2D Passivation a Secret to Success for Polycrystalline Thin-Film Solar Cells?
Three leading thin-film photovoltaic (PV) technologies - cadmium telluride (CdTe), CuIn1-xGaxSe2 (CIGS), and perovskite solar cells (PSCs) - are all polycrystalline, but otherwise appear to have little in common. A comprehensive examination of these technologies, however, reveals a common theme: the formation of two-dimensional (2D) van der Waals materials at three-dimensional (3D) absorber interfaces and grain boundaries. In CdTe, the 2D compound is CdCl2; in CIGS, it is XInSe2 (X= K, Rb, Cs) with X depending on the heavy-alkali post-deposition treatment used; and in lead halide PSCs, PbI2 forms naturally, but many new, more stable, 2D perovskites have also been incorporated. Generally, these 2D interfacial materials are present not by design, but instead have evolved from their 3D counterparts during standard device processing. Here, new data, together with evidence compiled from the literature, are presented to illustrate both the existence of 3D/2D interfaces in CdTe, CIGS, and PSCs, and their correlation with improved passivation and device performance. This suggests that 3D/2D passivation may be a heretofore unappreciated key to successful polycrystalline thin-film PV. Finally, the desired attributes of successful low-dimensional layers are presented with rational design strategies for next generation polycrystalline solar cells.
3D/2D↗
Chapter 10: Nanometer-Scale Characterization of Thin-Film Solar Cells by Atomic Force Microscopy-Based Electrical Probes
KPFM and SSRM, which relate to the following characterization reviews, will be introduced briefly in Section 10.2. Some recent nm-scale characterizations of perovskite, CIGS, and CdTe thin-film solar cell materials and devices will be reviewed in Sections 10.3-10.5 and closing remarks will be given in Section 10.6.
atomic force microscopy-based electrical probes↗
Codesigning Alloy Compositions of CdSe y Te 1− y Absorbers and Mg x Zn 1− x O Contacts to Increase Solar Cell Efficiency
Thin‐film solar cells such as CdTe are a major commercial photovoltaic technology, with more than 25 GW installed worldwide and levelized costs of electricity competitive with fossil fuels. Further progress may result from integrating CdSe y Te 1− y absorbers with Mg x Zn 1− x O contacts, but the device efficiency is difficult to maximize due to coupled dependence on chemical composition of both alloys. Herein, a high‐throughput approach is demonstrated to codesign chemical compositions in alloyed Mg x Zn 1− x O/CdSe y Te 1− y thin‐film solar cells, using combinatorial libraries of PV devices with orthogonal composition gradients in CdSe y Te 1− y absorbers and Mg x Zn 1− x O contacts. It is found that the solar cell performance is a strong and coupled function of both elemental compositions, with efficiency up to 17.7% ( V OC = 836 mV, fill factor = 69%, J SC = 30.6 mA cm −2 ) at atomic compositions of Mg/(Mg + Zn) ≈18% and average Se/(Se + Te) ≈4%. These performance trends among >100 devices are explained by >100 ns lifetime of photoexcited charge carriers at the Mg x Zn 1− x O/CdSe y Te 1− y interface where strong Se accumulation is also observed. This study reports the optimal compositions of the commercially relevant Mg x Zn 1− x O/CdSe y Te 1− y solar cells and demonstrates a general approach to codesigning performance of alloyed thin‐film solar cells and other optoelectronic devices.
14 SOLAR ENERGY↗
Low temperature and effective ex-situ group V doping for efficient polycrystalline CdSeTe solar cells
Presentation in the 2021 Monthly CdTe workshop
14 SOLAR ENERGY↗