Search NASA⌕ Search

SEARCH · Search NASA

Results for “GAS CELL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

An overview of various critical aspects of low-cobalt/cobalt-free Li-ion battery cathodes

Cathodes of lithium-ion batteries (LIBs) significantly impact the environmental footprint, cost, and energy performance of the battery-pack. Hence, sustainable production of Li-ion battery cathodes is critically required for ensuring cost-effectiveness, environmental benignity, consumer friendliness, and social justice. Battery chemistry largely determines individual cell performance as well as the battery pack cost and life cycle greenhouse gas emission. Continuous manufacturing platforms improve production efficiency in terms of product yield, quality and cost. Spent-battery recycling ensures the circular economy of critical elements that are required for cathode production. Innovations in fast-charging LIBs are particularly promising for sustainable e-mobility with a reduced carbon footprint. This article provides an overview of these research directions, emphasizing strategies for low-cobalt cathode development, recycling processes, continuous production and improvement in fast-charging capability.

25 ENERGY STORAGE↗
DOE OSTI2025

FCET Solid Oxide Fuel Cell Testing and Development (CRADA 526) (Final Report)

Pacific Northwest National Laboratory (PNNL) tested electrolyte coatings from Fuel Cell Enabling Technologies, Inc. (FCET) for use in solid oxide fuel cells (SOFCs). The key technology held by FCET is a process to deposit thin layers of oxide materials, less than 1 μm in thickness. The range of possible materials that can be deposited with their method is broad, but this project focused on the gadolinium-doped ceria (GDC) and yttria-stabilized zirconia (YSZ) electrolytes for SOFCs. Thin, gas tight electrolyte membranes have been a long-sought target in SOFC research. The thinner the electrolyte, the lower the cell resistance, and the higher performance of the cell (or the lower the operating temperature). A YSZ thickness of 1 μm would be a step change from the state-of-the-art, tape-cast electrolytes (~10 μm). An in-house prototype SOFC stack from FCET was first tested. The sealing geometry of the prototype stack was determined to be problematic, and testing shifted to button cells. Anode-supported solid oxide electrolysis cell (SOEC) button cells without an electrolyte layer were produced at PNNL and sent to FCET for coating with electrolyte. Three cells were tested with a gadolinium-doped ceria (GDC) electrolyte applied via spin coating. GDC was chosen for its conductivity at lower temperatures than YSZ. All three cells failed during initial reduction under hydrogen at 600°C. Testing then shifted to YSZ, which is the standard SOFC electrolyte. Several button cells were coated with YSZ and examined with scanning electron microscopy (SEM). A promising coating of ~1 mm thickness was observed under SEM. A similarly coated button cell was tested and failed similarly to previous tests during reduction at 600°C. The YSZ coating appeared dense and uniform in SEM analysis. The roughness of the underlying Ni/YSZ anode is on the order of 1 μm, and that may have compromised the gas-tightness of the coating. Further development is warranted to understand and refine the coating process. Thin YSZ applied via this spin-coating technique could be used as a low-cost, drop-in replacement in large-scale SOFC manufacturing processes, improving cell performance and lowering the cost per watt of SOFCs.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2025

Cold air quench control of local crystallization environment in fully air-processed carbon-based perovskite solar cells

Carbon-based perovskite solar cells (C-PSCs) present a low-cost route to efficient photovoltaic technology. Gas quenching is an essential process commonly used for solvent extraction in scalable module fabrication using solution processes, but film quality remains highly sensitive to the localized environmental processing temperature, especially during intermediate phase transitions before perovskite film high temperature annealing. In this study, we introduce a cold air quench strategy to precisely control the local crystallization temperature that simultaneously promotes uniform crystallization and facilitates strain relaxation in fully air-processed C-PSCs. It is found that implementing dry air at 10 °C as the quenching gas yields a champion power conversion efficiency (PCE) of 20.52 %, with preferential (110) orientation and reduced, homogenized in-plane strain. This newly developed technique of a cost-effective low temperature air quenching process also enhances carrier lifetime, reduces interface recombination, and improves charge extraction. Furthermore, this work presents cold air quenching as a scalable, economic method to control perovskite crystallization and strain in C-PSC fabrication, advancing the industrial viability of high-performance perovskite modules.

14 SOLAR ENERGY↗
DOE OSTI2025

Metabolic Redox Coupling Controls Methane Production in Permafrost‐Affected Peatlands Through Organic Matter Quality‐Dependent Energy Allocation

ABSTRACT Permafrost thaw represents one of Earth's largest climate feedback risks, potentially releasing vast carbon (C) stores as greenhouse gases (GHG). However, our ability to predict emissions remains limited by poor understanding of how changing organic matter (OM) composition affects microbial carbon processing. We test a metabolism‐centered redox framework, which views microbial processes as coupled oxidative‐reductive reactions, to mechanistically explain how organic matter metabolite quality controls greenhouse gas production in permafrost‐affected peatland ecosystems. Rather than relying solely on geochemical redox measurements, our approach examines how microbes balance electron flow through metabolic pathways. Using active layer peat (9–19 cm) from contrasting environments (bog and fen), we employed multi‐omics approaches, including metabolomics, metagenomics, and metatranscriptomics, to link OM chemistry to microbial function. Our results reveal distinct dissolved organic matter metabolite composition, with fen systems enriched in compounds with higher substrate quality (low molecular weight (MW) sugars with high H:C ratios and low aromaticity) and bog systems dominated by compounds with lower substrate quality (high MW phenols with lower H:C ratios and higher aromaticity). In fen samples, these sugar‐like compounds correlated with higher oxidative metabolism and methanogenesis, supported by increased glycolysis gene expression. Initially, electrons from increased oxidative metabolism were balanced through nitrate and sulfate reduction, but as these electron acceptors were depleted, methanogenesis increased to maintain redox balance. Fen samples showed rapid degradation of both high‐ and low‐substrate‐quality compounds, suggesting sufficient energy for efficient C cycling. Conversely, bog samples exhibited more polyphenolic compounds, lower glycolysis activity, and higher stress‐related gene expression, suggesting energy was diverted towards cell maintenance under acidic conditions rather than C processing. This approach suggests that predicting greenhouse gas emissions requires an understanding of how organic matter quality shapes microbial energy allocation strategies, providing a mechanistic framework for improving emission predictions from permafrost‐affected peatlands and similar ecosystems.

Biodiversity & Conservation↗
DOE OSTI2025

Understanding the Cathode Electrochemistry of Humidified Solid‐State Lithium‐Oxygen Batteries

Lithium-oxygen batteries (LOBs) possess a high theoretical energy density, making them potential candidates for next-generation energy storage. However, challenges such as reactive oxygen species-induced component degradation hinder their practical use. Inorganic solid-state electrolytes offer an alternative to degradation-prone aprotic electrolytes, while also protecting lithium anodes from potential atmospheric reactants. Here, this study explores the cathode electrochemistry of solid-state LOBs using humidified oxygen, which forms an aqueous catholyte during initial cycling, thereby improving cathode-electrolyte contact. To quantitatively analyze the cathode electrochemistry, a ‘Humidity-Incorporated’ Differential Electrochemical Gas Monitoring System (HiDEMS) is developed to control humidity and monitor gas consumption and evolution in real time. When studying a Li-O 2 cell that employs a NASICON-type Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 (LATP) solid electrolyte and a porous carbon cathode, a shift in discharge products from Li 2 O 2 to LiOH is observed over repeated cycles. While Li 2 O 2 evolves O 2 during charging, LiOH oxidation leads to minimal O 2 release and increased CO 2 production, originating from oxidation of carbon electrodes. Further, dissolution of Al and P from LATP is observed, likely driven by the formation of the alkaline catholyte. The findings highlight the need for carbon-free cathode materials and more stable solid-state conductors to minimize side reactions and improve rechargeability in humidified solid-state Li-O 2 batteries.

LATP degradation↗
DOE OSTI2026

Molecular Tuning of Ether Cosolvent Chemistry for High-Voltage Sodium-Ion Batteries

Ethers as electrolyte cosolvents in sodium-ion batteries (SIBs) provide favorable Na + solvation and interfacial properties, but their low oxidative stability limits their use in high-voltage SIBs. Herein, we address this limitation via molecular tuning of ether cosolvents for high-voltage (4.2 V) hard carbon || NaNi 0.33 Fe 0.33 Mn 0.33 O 2 full cells. Tetrahydropyran (THP) is functionalized with a nitrile group to form tetrahydropyran-4-carbonitrile (THPCN). To delineate the effect of nitrile functionalization and benchmark ether against a conventional carbonate, THP, THPCN, and diethyl carbonate (DEC) are evaluated as cosolvents with ethylene carbonate. Nitrile functionalization lowers the HOMO energy of the ether, extends the electrolyte stability window, and alters Na⁺ solvation. Spectroscopic techniques and molecular dynamics simulations reveal that THPCN exhibits predominantly aggregate-dominated solvation (95.1 %) with weakened Na + -solvent interactions, producing the most anion-rich environment relative to DEC and THP cosolvents. THPCN-modified solvation promotes the formation of highly conductive, fluorine-enriched interphases that suppress parasitic reactions. Pouch full cells with THPCN sustained ~ 600 cycles at 4.2 V, outperforming THP and DEC. Operando gas analysis reveals that THPCN reduces CO 2 generation by 45% and H 2 generation by 30% relative to THP. Furthermore, the findings demonstrate nitrile functionalization as a molecular design strategy to stabilize ethers and enable high-voltage SIBs.

25 ENERGY STORAGE↗
DOE OSTI2024

Ten-moment fluid model for low-temperature magnetized plasmas

In this paper, a one-dimensional 10-moment multi-fluid plasma model is developed and applied to low-temperature magnetized plasmas. The 10-moment model solves for six anisotropic pressure terms, in addition to density and three components of fluid momentum, which allows the model to capture finite kinetic effects. The results are benchmarked against a 5-moment model, which assumes that the gas constituents follow a Maxwellian velocity distribution function (VDF), and a particle-in-cell Monte Carlo collision model that allows for arbitrary non-Maxwellian VDFs. The models are compared in a one-dimensional, low-temperature, partially magnetized plasma test case. The 10-moment results accurately reproduce the anisotropic temperature profile in low-temperature magnetized plasmas, where shear gradients exist due to the E×B drift. We discuss the mechanisms by which the anisotropic pressure can be generated in low-temperature magnetized plasmas. In addition, the importance of a self-consistent heat flux closure to the 10-moment model is studied, showing consistency with other models only when the assumptions of the underlying model are met. The 10-moment model allows for study of electron inertia effects and non-Maxwellian VDFs without the need for kinetic methods that are more computationally expensive.

Kuldinow, Derek Amur (ORCID:0000000319730196)↗
DOE OSTI2025

Hybrid SOFC-Turbogenerator for Aircraft (Final Scientific/Technical Report)

The following paragraphs provide a high-level summary of the work performed during Phases I and II of this contract. Note that the order deviates from the WBS in places to better reflect the actual sequence of activities and the connections between them. Corresponding task numbers in the WBS are provided in parentheses after the task titles. There are a total of thirteen (13) tasks.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Acute wood smoke exposure is associated with cell-specific hippocampal transcriptomic responses in an accelerated ovarian failure mouse model

Background Wildfire events are increasing in frequency and intensity, and aging individuals demonstrate heightened biological susceptibility to air pollution exposures including increased risk of neurological sequelae. Declining ovarian hormones levels that occur with aging in females along with associated systemic physiological and inflammatory changes may contribute to increased cerebral vulnerability to air pollution, representing a potential but underexplored mechanism. Menopause and the menopausal transition represent a period of profound physiological change that affects cardiovascular, neurological, and immune health. Methods We tested whether peri-menopausal–like hormonal status amplifies hippocampal responses to acute wood smoke (WS) using an ovary-intact, 4-vinylcyclohexene diepoxide (VCD) model of moderate accelerated ovarian failure (AOF) in female C57BL/6 mice. Animals were exposed to HEPA-filtered air (FA) or WS for 4 h/day over 2 consecutive days (∼0.5 mg/m³). Exposure characterization confirmed a complex mixture of combustion products with significant levels of both trace metals and gas release during WS exposure. Results Spatial transcriptomics (10x Visium; n = 4 sections/group) with automated cell-type annotation identified astrocytes, GABAergic and glutamatergic neurons, oligodendrocytes, revealed cell type-specific transcriptional alterations following WS exposure. Distinct transcriptional patterns were observed across all identified neuronal and glial cell populations. Conclusion Together, these findings define a cell-type specific transcriptomic framework describing how WS exposure and ovarian hormone decline interact to influence hippocampal responses and identify potential cellular pathways relevant to hippocampal vulnerability.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗
DOE OSTI2024

Eliminating Signal Bias Caused by Vacuum System Backstreaming in the Diagnostic Residual Gas Analyzer of ITER

In fusion neutral gas analysis, such as with the Diagnostic Residual Gas Analyzer (DRGA) for ITER, the primary measurement range of interest comprises the low-amu species (1 to 6), especially deuterium and helium. The challenge in successfully obtaining accurate measurements is two-fold. First, the sensitivity of the method must be sufficient to resolve trace amounts accurately; typically, one percent or less. Second, the gas signal from the fusion processes must be free of bias caused by the latent presence (from system outgassing and/or vacuum backstreaming) of these gases to enable accurate interpretation of the measured signal. This latter criterion can be problematic for the lightest gases since there is a propensity for some fraction of the pumped gas load to undergo a phenomenon known as backstreaming. This behavior is manifested in pumping systems for gas properties related to relative atomic weight (lightest) and size (smallest). Backstreaming results in a significant amount of the pumped gas undertaking a reverse flow and re-entering the measurement region; thus, contaminating the forward, real-time measurement. To fully eliminate this adverse effect, a conductance-limiting device – or orifice – has been installed in the high-vacuum pumping system of the present ITER DRGA prototype. The system was already equipped with a secondary turbomolecular pump (TMP), but with limited effectiveness against backstreaming in the inter-pump volume (IPV). This orifice is placed within the suction inlet coupling of the secondary TMP, which is downstream of the IPV. Its objective is to eliminate the backstreaming phenomenon by increasing the back pressure in the IPV. However, the orifice sizing must take into consideration other factors, such as the diagnostic measurement objectives. For example, in the ITER DRGA, one of the measurement requirements is a dynamic response time of ~1s. Fortunately, an added benefit of the pumping restriction created by the orifice is that the upstream pressure increase is beneficial for the DRGA’s optical gas analysis (OGA) sensors. These sensors are attached to the IPV in the present design. The glow discharges, when used as an OGA light source, will typically have a brighter light emission with increasing plasma cell pressure. In addition to the fusion machine research sector, there are other potential applications of this pumping technique where the monitoring of lighter gas concentrations is essential, such as the photolithography process for the semiconductor fabrication of integrated circuits. This presentation will describe the vacuum system used to demonstrate a process to eliminate backstreaming as well as show test results to verify the accomplishment of this critical objective.

Marcus, Chris↗
DOE OSTI2024

Modeling the Effect of Material Properties on Liquid-Alkaline Water Electrolysis

Liquid-alkaline water electrolyzers (LAWEs) use electricity to drive the conversion of water to H 2 and O 2 gas. These devices benefit from the use of low-cost nickel electrodes and metal-oxide separators, but suffer from lower current densities and higher cell voltages than proton-exchange-membrane water electrolyzers. Identifying the inefficiencies that result in this poor performance is key to mitigating losses and optimizing LAWEs. Here, we report an experimentally-validated 1-D continuum model of a LAWE that elucidates the gradients within the cell, simulates H 2 crossover, and projects the energy improvements made possible by modulating the properties of the electrodes and separator. The model captures the Nernstian polarization losses and the distribution of gas- and liquid-phases within the electrodes, enabling quantification of energy losses associated with kinetic, ohmic, and bubble-induced (mass-transport) resistances. Simulations demonstrate that LAWE can achieve energy intensities of 50 kWh kg −1 of H 2 at 1 A cm −2 using improved electrode and separator properties.

08 HYDROGEN↗
DOE OSTI2025

Room temperature buffer gas beam of metastable state titanium atoms

We produce beams of neutral titanium (Ti) atoms in their metastable 3d3(F4)4sa5F5 state by laser ablation into He, N2, and Ar buffer gases. The high temperatures associated with the ablation process populate the a5F5 level without the need for optical pumping. Remarkably, we observe that Ti atoms in the a5F5 state survive thousands of collisions with He and Ar buffer gas atoms without being quenched to lower-energy states. We study the yield of Ti atoms when ablated into buffer gases of varying species and pressure, quantify quenching rates and diffusion cross sections based on simple models, and provide insight into optimal design parameters for an ablation cell. Using a 3.3 cm ablation cell with interchangeable exit apertures, we produce metastable atom beams and quantify their brilliance and velocity distributions as functions of buffer gas pressure.

Schrott, Jackson↗
DOE OSTI2026

Direct electrode-to-electrode regeneration of end-of-life batteries via electrode–electrolyte interphase dissolution

Lithium-ion battery recycling remains constrained by processes that recover metals at the expense of electrode integrity, while even direct recycling typically requires shredding to black mass followed by binder removal, separation, and full electrode refabrication. Here, we introduce direct electrode-to-electrode regeneration (DEER), a simultaneous electrochemical regeneration of used NMC and graphite electrodes from end-of-life batteries in their intact form by dissolving the passivating electrode–electrolyte interphase (EEI). DEER employs 1,3-dimethyl-2-imidazolidinone (DMI), a high donor number solvent that creates a thermodynamic environment favorable for solubilizing redox inactive EEI components. DEER dissolves the thick EEI on both used electrodes while preserving electrode integrity, enabling up to 95% capacity regain and improved cycling stability with a residual LiF-rich interphase. Operando Raman, operando IR, and post-mortem NMR directly track the electrochemically driven dissolution of carbonate-derived EEI species in the used DMI-based recycling electrolyte. Technoeconomic and life-cycle analyses show that DEER reduces the cost of recycled cell manufacturing by 56% relative to pyro- and hydrometallurgy, while lowering energy use and greenhouse gas emissions. Overall, DEER establishes the first validated pathway to directly regenerate and reuse electrodes harvested from truly end-of-life batteries, converting the key interfacial bottleneck into a controllable dissolution process and opening a practical route toward electrode level circularity.

Kim, Kiwon [Cornell Univ., Ithaca, NY (United Stat↗
DOE OSTI2024

ROADRUNNER MiniFuel Experiment: Irradiation Target Design and Sample Characterization

High-density uranium nitride (UN) is a fuel candidate for several advanced nuclear reactor designs currently under development. Because there are limited UN performance data relative to fuel fabrication impurity and density variation, an irradiation campaign has been developed as part of a collaborative effort among the University of Texas at San Antonio (UTSA), Westinghouse Electric Company, Oak Ridge National Laboratory (ORNL), and Los Alamos National Laboratory (LANL) under the Nuclear Science User Facilities program. This project, entitled ROADRUNNER, or Research On ADvancing the peRformance of UraNium Nitrides in Extreme enviRonments, aimsto support UN fuel qualification for advanced reactors by investigating the impact of density and impurity variations on UN performance as a function of irradiation temperature and burnup. The MiniFuel experiment vehicle developed by ORNL, which leverages the High Flux Isotope Reactor, was selected to perform this accelerated separate-effects irradiation testing. The experiment test matrix consists of six MiniFuel targets containing miniature UN fuel disks, and targets three distinct burnup levels (37.5, 60, and 75 MWd/kg U) and three distinct temperatures (600, 900, and 1200°C). Neutronics and thermal analyses were performed to determine the experimental parameters needed to meet the desired irradiation conditions and to predict the experiment components temperatures. UN pellets were fabricated at LANL with tightly controlled parameters to produce specimens with three distinct densities and three levels of carbon content. The pellets were then thinned down by UTSA to the experiment-required thickness. The pre-characterization of the specimens includes density measurements, carbon and oxygen contents, microstructure analysis, and x-ray computed tomography. The selected specimens will be assembled into the MiniFuel experiment, and the first ROADRUNNER MiniFuel targets are intended for HFIR insertion during the Fall of 2024. After irradiation, the targets will be shipped to ORNL’s hot cell facility for disassembly. The post-irradiation examination on the fuel specimens includes fission gas release measurements, visual inspection, fuel swelling measurements, gamma spectroscopy, and microstructure analysis. The data collected post-irradiation will be used to develop fuel performance models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Admissible Powertrain Alternatives for Heavy-Duty Fleets: A Case Study on Resiliency and Efficiency

Heavy-duty vehicles dominate global freight movement and primarily rely on fossil-derived diesel fuel. However, fluctuations in crude oil prices and evolving emissions regulations have prompted interest in alternative powertrains to enhance fleet energy resiliency. This study paired real-world operational data from a large commercial fleet with high-fidelity vehicle models to evaluate the potential for replacing diesel internal combustion engine (ICE) trucks with alternative powertrain architectures. The baseline vehicle for this analysis is a diesel-powered ICE truck. Alternatives include ICE trucks fueled by bio- and renewable diesel, compressed natural gas (CNG) or hydrogen (H 2 ), as well as plug-in hybrid (PHEV), fuel cell electric (FCEV), and battery electric vehicles (BEV). While most alternative powertrains resulted in some payload capacity loss, the overall fleetwide impact was negligible due to underutilized payload capacity for the specific fleet considered in this study. For sleeper cab trucks, CNG-powered trucks achieved the highest replacement potential, covering 85% of the fleet. In contrast, H 2 and BEV architectures could replace fewer than 10% and 1% of trucks, respectively. Day cab trucks, with shorter daily routes, showed higher replacement potential: 98% for CNG, 78% for H 2 , and 34% for BEVs. However, achieving full fleet replacement would still require significant operational changes such as route reassignment and enroute refueling, along with considerable improvements to onboard energy storage capacity. Additionally, the higher total cost of ownership (TCO) for alternative powertrains remains a key challenge. This study also evaluated lifecycle impacts across various fuel sources, both fossil and bio-derived. Bio-derived synthetic diesel fuels emerged as a practical option for diesel displacement without disrupting operations. Conversely, H 2 and electrified powertrains provide limited lifecycle impacts under the current energy scenario. This analysis highlights the complexity of replacing diesel ICE trucks with admissible alternatives while balancing fleet resiliency, operational demands, and emissions goals. These results reflect a US-based fleet’s duty cycles, payloads, GVWR allowances, and an assumption of depot-only refueling/recharging. Applicability to other fleets and regions may differ based on differing routing practices or technical features such as battery swapping.

BEV↗
DOE OSTI2026

Examination of entrainment, combustibility, and heat transfer due to cell venting inside simplified battery energy storage enclosures

Battery energy storage systems (ESS) assembled of modules containing lithium-ion batteries can pose fire and explosion hazards during thermal runaway because vented gases may accumulate, combust, or escape enclosures. Here, we propose a prototypical configuration composed of the main components of an ESS rack, where modules are represented as rectangles within an enclosure and vent gas is injected steadily through the top of a module. This idealized geometry allows for exploration of how rack-level characteristics can influence smaller single-cell or module-level scales. Through this geometry, we conduct numerical simulations to understand how variations in the vent velocity, temperature, and vertical location affect entrainment rates, fraction of uncombusted fuel, rich-gas coverage, and heat flux to other modules. At lower vent velocities and vertical positions, buoyancy drives enough entrainment and mixing to react with most of the vent gases on the converging plenum. As jet momentum increases and/or buoyancy decreases via higher vent position in the rack, vent gases can propagate into and burn in the divergence plenum. Heat flux to the impinged module scales strongly with vent momentum and temperature, while heat transfer to upper modules peaks when flames in the diverging plenum reach the surface and declines when combustion is suppressed.

Computational fluid dynamics↗
DOE OSTI2025

Renewable Hydrogen to Vehicle (RH2V) – Operation Verification and Risk Mitigation Studies: Original Agreement (Modification 0) (CRADA Final Report)

Toyota has announced plans for commercial fuel cell vehicle deployment in 2015. To fully realize the benefits of fuel cell vehicles (zero emission with no performance loss in terms of vehicle range and capability), hydrogen produced efficiently from renewable sources is necessary. Most of the hydrogen fueling stations today utilize hydrogen reformed from natural gas (produced onsite or delivered). This enables more stations to be deployed cost-effectively within a network. Producing and using cost-effective renewable hydrogen in fuel cell vehicles will enable realization of the full potential. A viable option of green hydrogen that reliably delivers on the full suite of benefits for Toyota fuel cell vehicle drivers is needed. NREL is in a unique position to analyze and optimize renewable hydrogen production scenarios using the Energy Systems Integration Facility (ESIF), a facility that is specifically designed to evaluate renewable energy integration technologies. As the U.S. Department of Energy's (DOE) primary national laboratory for renewable energy and energy efficiency research and development, NREL has extensive knowledge of photovoltaic systems as well as alternative renewable technologies for efficient and reliable production of green hydrogen.

08 HYDROGEN↗
DOE OSTI2024

Development of a multiphase PIC model for slurry flow modeling

MFIX-Exa is a recently released multiphase CFD code originally developed for the simulation of particle-laden gas-solid flows. Due to its high-performance computing capabilities, MFIX-Exa is an ideal candidate for scale-up studies of slurry reactors, specifically the coarse-grained particle-in-cell (PIC) model with its statistical treatment of the particle phase. Unfortunately, several physical models that were neglected during original development because they are not relevant for high-density ratio gas-solid flows are important in slurry flows where the particle-to-fluid density ratio is near unity. In this preliminary work we focus on the effective (suspension) viscosity. The models of Brinkman (1952), Krieger and Dougherty (1956), and Cheng and Law (2003) are considered. The impact of the effective viscosity model is studied on horizontal pipe flow. The experimental data of Gillies et al. (2002) is used to assess the pressure drop predictions.

Fullmer, William D.↗