Search NASA⌕ Search

SEARCH · Search NASA

Results for “Inspection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Development of a Semi-autonomous Miniature Rover for Inspection of Double Shell Tank Floors - 19575

Leaks in the primary liner of double-shell tank (DST) 241-AY-102 at Hanford have prompted the need for the development of inspection tools that are able to access confined spaces around and underneath the tanks. Last year, Florida International University (FIU) has continued to improve inspection tools that were developed in the previous years, to ensure that the resultant tools are able to overcome the challenges posed by the DSTs. Experimental testing conducted last year at the full-scale sectional mock-up of the DST's refractory slots revealed some shortcomings of the miniature rover, particularly in traversing over weld seams of different heights. The weld seams are the results of welded steel plate-joints for the DST. It was advised by the site engineers that the weld seams height could range from 6.35 mm - 9.525 mm (1/4 to 3/8 inches), and with 12.7 mm (1/2 inches) width. As the rover traverses over a weld seam, the gap between the rover's magnets and tank surface increases, causing the adhesive force to drop. The rover loses its surface contact if this adhesive force drops below its weight, jeopardizing the inspection tasks. In this paper, we present the numerical studies to calculate the minimum magnetic force required for the miniature rover to traverse over weld seams with different heights and the corresponding modifications to the rover design. Initial bench scale tests were conducted using a steel bar with 5 welds of varying heights. The testing validated the results from the simulation studies and established the rover's capability in traversing weld seams. Another challenge for the miniature rover is the use of a joystick or keypad for manual control. Utilizing these controls will likely be difficult for the operators due to the tight channels underneath the tank. Having a semi-autonomous navigational capability would alleviate the complexity of the inspection tasks and allow the operator to focus on the channel inspection. The goal is to implement lane-keeping capability, akin to that of a driverless car, for the inspection tool, so that it will maintain its relative position with respect to the wall of the channels. Am image processing pipeline has been developed using both the Robot Operating System (ROS) and OpenCV to process the image stream coming from the onboard camera, for the purpose of lane identification. Additionally, a PID controller has been implemented to navigate the miniature rover along the central location of the detected lane, while allowing the operator to control the tool's forward and backward motion. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Development and Evaluation of a Drone-Deployed Wind Turbine Blade Nondestructive Inspection System

Wind energy is quickly becoming a significant contributor to the United States' overall energy portfolio. Wind turbine blades pose a unique set of inspection challenges that span from very thick and attenuative spar cap structures to porous bond lines, varying core material and a multitude of manufacturing defects of interest. The need for viable, accurate nondestructive inspection (NDI) technology becomes more important as the cost per blade, and lost revenue from downtime, grows. To address this growing need, Sandia and SkySpecs collaborated to evaluate NDI methods that are suitable for integration on an autonomous drone inspection platform. A trade study of these NDI methods was performed, and thermography was selected as the primary technique for further evaluation. Based on the capabilities of SkySpecs' custom inspection drone, a miniature microbolometer IR camera was successfully selected and tested in a benchtop setting. After identifying key operating parameters for inspecting wind blade materials, hardware and software integration of the IR camera was performed, and Sandia and SkySpecs conducted initial field testing. Finally, recommendations for a path forward for drone-deployed thermography inspections were provided.

17 WIND ENERGY↗

NDE Technology Engineering Program for Hanford DST Non-Visual Volumetric Inspection Technology: Phase II RAVIS Radiation Tolerance Test Report

This test report provides the results of radiation tolerance robustness testing that was performed on samples of robotic components and an ultrasonic guided wave air-slot sensor that represent components/sub-systems of the Robotic Air-slot Volumetric Inspection System (RAVIS) that has been engineered for volumetric inspection of Hanford tank bottom plates via under-tank refractory pad air-slots. The specific components tested for 1) functionality during active irradiation and 2) tolerance to cumulative radiation dose (until failure or upon reaching a cumulative dose test limit) were: • four samples each of a printed circuit board (PCB) and direct current (DC) motor, which are robotic components, and • 26 ultrasonic piezoelectric elements (samples) inside an air-slot sensor. The robotic components are part of the RAVIS air-slot inspection crawler drive control system that is responsible for remote communication with and actuation of the air-slot inspection crawler. The failure of either of these components during under-tank deployment would require manual retrieval via the crawler’s tether, which risks damage to the robot/refractory/tank. Preemptive replacement of the components at appropriately conservative dose/time intervals informed by failure dose would reduce the likelihood of under-tank failure. The components were included in radiation tolerance testing to quantify their failure doses to inform replacement intervals. The air-slot sensor is responsible for collecting ultrasonic inspection data (scan images) for the tank bottom plates during under-tank deployment. Compromised signal quality due to elevated noise levels caused by gamma radiation would compromise inspection performance. The air-slot sensor was included in radiation tolerance testing to quantify the impact of active irradiation on sensor signal quality. The irradiation and in-situ functional tests of the PCBs, DC motors and air-slot sensor took place in June and July 2020 at the Pacific Northwest National Laboratory. Testing was performed at a gamma dose rate near 300 rad/hr., which, in the absence of under-tank dose rate data, has been conservatively estimated to be the upper-bound dose rate beneath the primary tanks at Hanford. Irradiation took place at elevated temperatures of 150-200°F to determine failure doses that reflect the compounding effects of gamma radiation and heat. The test results revealed: • The DC motors can tolerate being actively irradiated at the high dose rate at 200°F and can tolerate a cumulative dose of 300,000 rad, that which would be incurred after 5 years of service at the 300 rad/hr dose rate. The component therefore meets minimum and preferred radiation tolerance and lifecycle requirements for robotic components. • The air-slot sensor can tolerate being actively irradiated at the high dose rate at 150°F and can tolerate a cumulative dose of 60,000 rad, that which would be incurred after 1 year of service at the 300 rad/hr dose rate. The sensor therefore meets minimum radiation tolerance and lifecycle requirements. • The PCB can tolerate being actively irradiated at the high dose rate, but can only tolerate a cumulative dose of 19,000 rad at 150-200°F. The PCB does not meet minimum radiation tolerance and lifecycle requirements; however, because the component is considered replaceable, it can be replaced before a cumulative dose of 19,000 rad is reached, determined through either monitoring with a dosimeter or scheduled time intervals that are calculated based on conservative estimates of under-tank dose rates.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Networked-based Cyber Analysis using Deep Packet Inspection (DPI) for High-Speed Networks

Today’s networked systems utilize advanced security components such as Next Generation Firewall (NGFW), Intrusion Detection Systems (IDS), Intrusion Prevention Systems (IPS), and methods for network traffic classification. A fundamental aspect of these security components and methods is network packet visibility and packet inspection. To achieve packet visibility, a compute mechanism used by these security components and methods is Deep Packet Inspection (DPI). DPI is used to obtain visibility into packet fields by looking deeper inside packets, beyond just IP address, port, and protocol. However, DPI is considered extremely expensive in terms of compute processing costs and very challenging to implement on high speed network systems. The fundamental scientific paradigm addressed in this research project is the application of greater network packet visibility and packet inspection at data rates greater than 40Gbps to secure computer network systems. The greater visibility and inspection will enable detection of advanced content-based threats that exploit application vulnerabilities and are designed to bypass traditional security approaches such as firewalls and antivirus scanners. Greater visibility and inspection are achieved through identification of the application protocol (e.g., HTTP, SMTP, Skype) and, in some cases, extraction and processing of the information contained in the packet payload. Analysis is then performed on the resulting DPI data to identify potentially malicious behavior. In order to obtain visibility and inspect the application protocol and contents at high speed data rates, advanced DPI technologies and implementations are developed.

97 MATHEMATICS AND COMPUTING↗

Historic Source Inspection Records

To create true counts of number of containers, each container can be identified by a combination of the purchase order, unique part number and type of inspection. The column TestEventName and any columns derived from TestEventName should not be used in the instance of presource inspection because the vendor may mete out testing over multiple months, meaning that a container would be counted twice if a single test was completed in one month and another test in a different month. By counting on this combination of values, we are able to drop row entries that signify multiple tests completed on a single container. Inspection type must be used because each container will be tested by the vendor and re-tested by the LANL container engineering team. Recall that the vendor will complete action limit tests for the full set of containers during pre-source inspection but during source inspection, action limit tests are completed for only a random subset. However, LANL SMEs will complete a manual inspection for the full set of containers.

42 ENGINEERING↗

Technical Letter Report Assessment of Ultrasonic Phased Array Inspection Method for Welds in Cast Austenitic Stainless Steel Pressurizer Surge Line Piping JCN N6398, Task 1B

Research is being conducted for the U.S. Nuclear Regulatory Commission (NRC) at the Pacific Northwest National Laboratory (PNNL) to assess the effectiveness and reliability of advanced nondestructive examination (NDE) methods for the inspection of light water reactor components. The scope of this research encompasses primary system pressure boundary materials including cast austenitic stainless steels (CASS); dissimilar metal welds; piping with corrosion-resistant cladding; weld overlays, inlays and onlays; and far-side examinations of austenitic piping welds. A primary objective of this work is to evaluate various NDE methods to assess their ability to detect, localize, and size cracks in coarse-grained steel components. In this effort, PNNL supports cooperation with Commissariat à l’Energie Atomique (CEA) to assess reliable inspection of CASS materials. The NRC Project Manager has established a cooperative effort with the Institut de Radioprotection et de Surete Nucleaire (IRSN). CEA, under funding from IRSN, are supporting collaborative efforts with the NRC and PNNL. Regarding its work on the NDE of materials, CEA is providing its modeling software (CIVA) in exchange for PNNL offering expertise and data related to phased-array detection and sizing, acoustic attenuation, and back scattering on CASS materials. This collaboration benefits the NRC because CEA performs research and development on CASS for Électricité de France (EdF). This technical letter report provides a summary of a technical evaluation aimed at assessing the capabilities of phased-array (PA) ultrasonic testing (UT) methods as applied to the inspection of welds in CASS pressurizer (PZR) surge line nuclear reactor piping. A set of thermal fatigue cracks (TFCs) was implanted into three CASS PZR surge-line specimens (pipe-to-elbow welds) that were fabricated using vintage CASS materials formed in the 1970s, and flaw responses from these cracks were used to evaluate detection and sizing performance of the PA-UT methods applied. This effort was comprised of multiple elements that included use of microstructural knowledge (dimensional analysis, grain orientation, and grain type) as well as sound field modeling to more effectively modify inspection parameters and enhance the inspection outcomes. Advanced probe design and sound field simulations were employed to enhance detection and characterization of circumferentially oriented flaws, and an assessment of lateral (circumferential) flaw localization capability and performance was also conducted. An evaluation of flaw detection, length sizing, depth sizing, and signal-to-noise ratio was performed for all flaws in the subject specimens, as a function of various inspection parameters, and finally, measurements were made to quantify and assess the baseline CASS material noise and its potential impact on flaw detection.

36 MATERIALS SCIENCE↗

Integrating Electromagnetic Acoustic Transducers in a Modular Robotic Gripper for Inspecting Tubular Components

Tubular structures are critical components in infrastructure such as power plants. Throughout their life, they are subjected to extreme conditions or suffer from defects such as corrosion and cracks. Although regular inspection of these components is necessary, such inspection is limited by safety-related risks and limited access for human inspection. Robots can provide a solution for automatic inspection. The main challenge, however, lies in integrating sensors for nondestructive evaluation with robotic platforms. As part of developing a versatile lizard-inspired tube inspector robot, in this study the authors propose to integrate electromagnetic acoustic transducers into a modular robotic gripper for use in automated ultrasonic inspection. In particular, spiral coils with cylindrical magnets are integrated into a novel friction-based gripper to excite Lamb waves in thin cylindrical structures. To evaluate the performance of the integrated sensors, the gripper was attached to a robotic arm manipulator and tested on pipes of different outer diameters. Two sets of tests were carried out on both defect-free pipes and pipes with simulated defects, including surface partial cracking and corrosion. The inspection results indicated that transmitted and received signals could be acquired with an acceptable signal-to-noise ratio in the time domain. Moreover, the simulated defects could be successfully detected using the integrated robotic sensing system.

Materials Science↗

Inspection error and its adverse effects - A model with implications for practitioners

Inspection error has clearly been shown to have adverse effects upon the results desired from a quality assurance sampling plan. These effects upon performance measures have been well documented from a statistical point of view. However, little work has been presented to convince the QC manager of the unfavorable cost consequences resulting from inspection error. This paper develops a very general, yet easily used, mathematical cost model. The basic format of the well-known Guthrie-Johns model is used. However, it is modified as required to assess the effects of attributes sampling errors of the first and second kind. The economic results, under different yet realistic conditions, will no doubt be of interest to QC practitioners who face similar problems daily. Sampling inspection plans are optimized to minimize economic losses due to inspection error. Unfortunately, any error at all results in some economic loss which cannot be compensated for by sampling plan design; however, improvements over plans which neglect the presence of inspection error are possible. Implications for human performance betterment programs are apparent, as are trade-offs between sampling plan modification and inspection and training improvements economics.

Collins, R. D., Jr.↗

In-service inspection methods for graphite-epoxy structures on commercial transport aircraft

In-service inspection methods for graphite-epoxy composite structures on commercial transport aircraft are determined. Graphite/epoxy structures, service incurred defects, current inspection practices and concerns of the airline and manufacturers, and other related information were determind by survey. Based on this information, applicable inspection nondestructive inspection methods are evaluated and inspection techniques determined. Technology is developed primarily in eddy current inspection.

Phelps, M. L.↗

Recertification analysis and inspection planning for environmental test facilities

Program development and implementation for recertification of pressure vessels used at NASA facilities are outlined, together with inspection procedures. The recertification is carried out in three phases: analysis, inspection planning, and long term inspection plans and management. A data base was developed for each piece of equipment and the associated performance parameters. Either documentation was obtained or NDT was performed on the vessels to confirm design and Code compliance. A Failure Modes and Effects Analysis technique was used to target recurring inspection items and guidelines were drawn up for inspections of parts and systems and intervals between inspections. The steps taken in establishing the program are considered applicable in both research and industrial situations.

Rebeck, K. J.↗

Automated inspection of solder joints for surface mount technology

Researchers at NASA/GSFC evaluated various automated inspection systems (AIS) technologies using test boards with known defects in surface mount solder joints. These boards were complex and included almost every type of surface mount device typical of critical assemblies used for space flight applications: X-ray radiography; X-ray laminography; Ultrasonic Imaging; Optical Imaging; Laser Imaging; and Infrared Inspection. Vendors, representative of the different technologies, inspected the test boards with their particular machine. The results of the evaluation showed limitations of AIS. Furthermore, none of the AIS technologies evaluated proved to meet all of the inspection criteria for use in high-reliability applications. It was found that certain inspection systems could supplement but not replace manual inspection for low-volume, high-reliability, surface mount solder joints.

Savage, Robert M.↗

Inspection planning development: An evolutionary approach using reliability engineering as a tool

This paper proposes an evolutionary approach for inspection planning which introduces various reliability engineering tools into the process and assess system trade-offs among reliability, engineering requirement, manufacturing capability and inspection cost to establish an optimal inspection plan. The examples presented in the paper illustrate some advantages and benefits of the new approach. Through the analysis, reliability and engineering impacts due to manufacturing process capability and inspection uncertainty are clearly understood; the most cost effective and efficient inspection plan can be established and associated risks are well controlled; some inspection reductions and relaxations are well justified; and design feedbacks and changes may be initiated from the analysis conclusion to further enhance reliability and reduce cost. The approach is particularly promising as global competitions and customer quality improvement expectations are rapidly increasing.

Graf, David A.↗

Thermographic Inspection of Metallic Honeycomb Sandwich Structures

The X-33/VentureStar has a Thermal Protection System (TPS) consisting mainly of brazed metallic honeycomb sandwich structures. Inspection of these structures is changing as a result of the extremely thin (less than 200 microns) skins, the small critical defect size (less than 2 mm long by 100 microns wide) and the large number (more than 1000) of parts to be inspected. Pulsed Infrared Thermography has been determined to be the most appropriate inspection method for manufacturing inspection based on performance comparison with other methods, cost, schedule and other factors. The results of the assessment of the different methods will be summarized and data on the performance of the final production inspection system will be given. Finite difference thermal methods have been used to model the whole inspection process. Details of correlation between the models and experimental data will be given and data on the use of pulsed infrared thermography on other metallic honeycomb sandwich structures will be given.

Taylor, John O.↗

Automatic Inspection of Aircraft Using Open-Architecture Robotic Platforms

Aging aircraft structures and composite materials are requiring rapid inspection of large areas. Removal from the aircraft for NDE at an inspection facility is not economical as compared to field inspection. Detection and characterization of defects are labor intensive, time consuming and when the process is manual the results are subjected to human error. These limitations of NDE created a need for portable, user friendly inspection systems that can rapidly scan large areas of complex structures and locate all the detrimental material conditions. Addressing this need has been an evolutionary process that followed the technology trend, and unique devices were developed to allow rapid field inspection. This development involves multi-disciplinary approaches to integrate NDE, telerobotics, neural networks, advanced materials science, imbedded computing and automated control. These efforts have led to the development of various portable inspection systems and the current trend is towards fully automatic systems that will operate autonomously.

Bar-Cohen, Yoseph↗

Automated Inspection of the RSRM Case O-Ring Seal Surface

An automated inspection system has been developed to inspect the o-ring sealing surfaces on the Space Shuttle reusable solid rocket motor (RSRM) case segment joints. A laser digitizing system is used to create a three dimensional map of the o-ring sealing surfaces. This data is analyzed for any irregularities, which are noted for further inspection and disposition. This paper describes both the hardware and the software used to gather data as well as the methods developed to analyze the data. The RSRM is assembled from four casting segments. Each of the field joints between these segments is sealed with three o-rings. These o-rings are critical for the proper operation of the motor. After launch the booster segments are recovered and reused. As part of the refurbishment process the o-ring sealing surfaces are inspected for any irregularities. The system developed uses a combination of commercial and customized hardware and software. The system uses two computer systems in a real time environment to control a laser, an XYZ precision table, and case rotation and position information. The system is capable of inspecting both the tang end and the clevis end of the RSRM field joint. The o-ring grooves and flat sealing surfaces are inspected.

ODell, Keith P.↗

Development of an Extra-vehicular (EVA) Infrared (IR) Camera Inspection System

Designed to fulfill a critical inspection need for the Space Shuttle Program, the EVA IR Camera System can detect crack and subsurface defects in the Reinforced Carbon-Carbon (RCC) sections of the Space Shuttle s Thermal Protection System (TPS). The EVA IR Camera performs this detection by taking advantage of the natural thermal gradients induced in the RCC by solar flux and thermal emission from the Earth. This instrument is a compact, low-mass, low-power solution (1.2cm3, 1.5kg, 5.0W) for TPS inspection that exceeds existing requirements for feature detection. Taking advantage of ground-based IR thermography techniques, the EVA IR Camera System provides the Space Shuttle program with a solution that can be accommodated by the existing inspection system. The EVA IR Camera System augments the visible and laser inspection systems and finds cracks and subsurface damage that is not measurable by the other sensors, and thus fills a critical gap in the Space Shuttle s inspection needs. This paper discusses the on-orbit RCC inspection measurement concept and requirements, and then presents a detailed description of the EVA IR Camera System design.

Gazarik, Michael↗

The Application of Principal Component Analysis Using Fixed Eigenvectors to the Infrared Thermographic Inspection of the Space Shuttle Thermal Protection System

The Nondestructive Evaluation Sciences Branch at NASA s Langley Research Center has been actively involved in the development of thermographic inspection techniques for more than 15 years. Since the Space Shuttle Columbia accident, NASA has focused on the improvement of advanced NDE techniques for the Reinforced Carbon-Carbon (RCC) panels that comprise the orbiter s wing leading edge. Various nondestructive inspection techniques have been used in the examination of the RCC, but thermography has emerged as an effective inspection alternative to more traditional methods. Thermography is a non-contact inspection method as compared to ultrasonic techniques which typically require the use of a coupling medium between the transducer and material. Like radiographic techniques, thermography can be used to inspect large areas, but has the advantage of minimal safety concerns and the ability for single-sided measurements. Principal Component Analysis (PCA) has been shown effective for reducing thermographic NDE data. A typical implementation of PCA is when the eigenvectors are generated from the data set being analyzed. Although it is a powerful tool for enhancing the visibility of defects in thermal data, PCA can be computationally intense and time consuming when applied to the large data sets typical in thermography. Additionally, PCA can experience problems when very large defects are present (defects that dominate the field-of-view), since the calculation of the eigenvectors is now governed by the presence of the defect, not the good material. To increase the processing speed and to minimize the negative effects of large defects, an alternative method of PCA is being pursued when a fixed set of eigenvectors is used to process the thermal data from the RCC materials. These eigen vectors can be generated either from an analytic model of the thermal response of the material under examination, or from a large cross section of experimental data. This paper will provide the details of the analytic model; an overview of the PCA process; as well as a quantitative signal-to-noise comparison of the results of performing both embodiments of PCA on thermographic data from various RCC specimens. Details of a system that has been developed to allow insitu inspection of a majority of shuttle RCC components will be presented along with the acceptance test results for this system. Additionally, the results of applying this technology to the Space Shuttle Discovery after its return from flight will be presented.

Cramer, K. Elliott↗

Interim Report on Heuristics about Inspection Parameters: Updates to Heuristics Resulting from Refinement on Projects

In 2008, we have continued analyzing the inspection data in an effort to better understand the applicability and effect of the inspection heuristics on inspection outcomes. Our research goals during this period are: 1. Investigate the effect of anomalies in the dataset (e.g. the very large meeting length values for some inspections) on our results 2. Investigate the effect of the heuristics on other inspection outcome variables (e.g. effort) 3. Investigate whether the recommended ranges can be modified to give inspection planners more flexibility without sacrificing effectiveness 4. Investigate possible refinements or modifications to the heuristics for specific subdomains (partitioned, e.g., by size, domain, or Center) This memo reports our results to date towards addressing these goals. In the next section, the first goal is addressed by describing the types of anomalies we have found in our dataset, how we have addressed them, and the effect of these changes on our previously reported results. In the following section, on "methodology", we describe the analyses we have conducted to address the other three goals and the results of these analyses are described in the "results" section. Finally, we conclude with future plans for continuing our investigation.

Shull, Forrest↗