Search NASA⌕ Search

SEARCH · Search NASA

Results for “Structural Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Influence of topology optimization parameters on the mechanical response of an additively manufactured test structure

Topology Optimization (TO) determines a material distribution within a domain under given conditions and design constraints, and generally generates complex geometries as a result. Complementary to TO, Additive Manufacturing (AM) offers the ability to fabricate complex geometries which may be difficult to manufacture using traditional techniques such as milling. AM has been used in multiple industries including the medical devices area. Hence, TO may be used to create patient-matched devices where the mechanical response is catered to a particular patient. Furthermore, during a medical device regulatory 510(k) pathway, demonstrating that worst-cases are known and tested is critical to the review process. Using TO and AM to predict worst-case designs for subsequent performance testing may be challenging and does not appear to have been thoroughly explored. Investigating the effects of TO input parameters when AM is employed may be the first step in determining the feasibility of predicting these worst-cases.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Degradation Mode Identification by Photocarrier Lifetime Spectroscopy on Devices and Test Structures

In this presentation, I examine the basic concepts of the device physics that can be used to distinguish various degradation and recovery modes on a cell level. The known degradation modes (bulk LeTID and LID, UVID, etc.) are due to defects and impurities that cause the photocarrier recombination according to Shockley-Reed-Hall (SRH) statistics. The SRH recombination rate strongly depends on the balance of electron and hole capture rates into the defects, which in turn, are governed by their local concentrations. The strongest recombination takes place at approximately equal concentrations of electrons and holes, while at low injection conditions (when one type of carrier dominates) the SRH recombination is suppressed. For cell degradation modes that affect the passivated interface (UVID, H-induced TOPCon contact degradation) the defects are at the interface under low-injection conditions due to either high local doping or the adjacent built-in charge in the dielectric. This mode is characterized by changes in the "diode prefactor" J01 slope in the inverse lifetime-injection level curve. In contrast, bulk degradation (LeTID, LID) affects bulk lifetime, with J01 slope unchanged. Carrier lifetime - injection level plots therefore serve as clear indicators of different degradation modes and are shown by experimental examples.

14 SOLAR ENERGY↗
DOE OSTI2023

Cyclic Thermal and Structural Testing of a Hot Particle Storage Bin

Thermal energy storage is a key element in concentrating solar energy systems. In 2017 a Roadmap toward a third-generation system that could meet the SunSHOT goals of 0.06 $/kWe recommended increasing temperatures to > 700° C for heat transfer media to in-crease thermal efficiencies and lower levelized costs of heat. In 2021, the U.S. Department of Energy selected the particle pathway, G3P3, to build a 1 MWt prototype solar tower with 6 MWh thermal energy storage at the NSTTF in Albuquerque, NM. Of the primary components, the falling particle receiver, and particle-to-sCO2 heat exchanger have been demonstrated at the 250 kWt capacity. The storage component is now being demonstrated as part of the G3P3-USA and G3P3-KSA pilot plants. Storage bin liner materials have been demonstrated by KSU in 2016 and 2019. A flowing particle storage container was demonstrated in 2020 by KSU. The testing presented in this work will be the first to test the particle to wall interactions with mono-lithic refractory insulation, and to validate a transient thermal transport model with the unique kinetics of bulk solids in funnel-flow where cooler particles near the walls flow inward toward a hot central flow channel. This work will also de-risk and characterize the specific design of the G3P3-USA storage bin.

Sment, Jeremy↗
NASA NTRS1972

The use of models in structural testing.

The design, construction and instrumentation of plastic model shells used in elastic stability studies is discussed. The work demonstrates that specimens made of such materials are of great value in parametric studies because of their ease of manufacture and the simplicity of modification. Additionally, it is shown that they are most useful in the development of nondestructive test techniques. The paper indicates how deformation measurements made at low load levels can be used to accurately predict critical conditions.

Horton, W. H.↗
NASA NTRS1973

Hydrogen depolarized carbon dioxide concentrator performance improvements and cell pair structural tests

The investigations and testing associated with the CO2 removal efficiency and voltage degradation of a hydrogen depolarized carbon oxide concentrator are reported. Also discussed is the vibration testing of a water vapor electrolysis cell pair. Performance testing of various HDC cell pairs with Cs2CO3 electrolyte provided sufficient parametric and endurance data to size a six man space station prototype CO2 removal system as having 36 HDC cell pairs, and to verify a life capability exceeding six moths. Testing also demonstrated that tetramethylammonium carbonate is an acceptable HDC electrolyte for operating over the relative humidity range of 30 to 90 percent and over a temperature range of 50 to 80 F.

Huddleston, J. D.↗
NASA NTRS1979

Capability for aerothermal-structural tests of large-to-full-scale components of future space transportation systems

The design of viable, low-mass thermostructural concepts for future space transportation systems requires accurate definition of the localized heat flux, pressures, and flow-surface interaction parameters for complex flow regions of detailed areas of large vehicles, such as wing-elevon coves, thermal protection system tile gaps, and corrugated metallic surfaces. This paper discusses investigations recently conducted in and planned for two high-energy wind tunnels at the Langley Research Center - the 8-foot High-temperatures Tunnel and the Thermal Protection System Test Facility. The data obtained on large-to-full-scale vehicle components, comparisons of the experimental data with theory, and the large, reusable, generalized test apparatus available at or planned for these facilities are discussed.

Couch, L. M.↗
NASA NTRS1981

Status and future plans of the Drones for Aerodynamic and Structural Testing (DAST) program

Results from flight tests of the ARW-1 research wing are presented. Preliminary loads data and experiences with the active control system for flutter suppression are included along with comparative results of test and prediction for the flutter boundary of the supercritical research wing and on performance of the flutter suppression system. The status of the ARW-2 research wing is given.

Murrow, H. N.↗
NASA NTRS1992

Structural testing of the technology integration box beam

A full scale section of a transport aircraft wing box was designed, analyzed, fabricated, and tested. The wing box section, which was called the technology integration box beam, contained blade stiffened covers and T-stiffened channel spars constructed using graphite-epoxy materials. Covers, spars, and the aluminum ribs were assembled using mechanical fasteners. The box beam was statically tested for several loading conditions to verify the stiffness and strength characteristics of the composite wing design. Failure of the box beam occurred at 125 pct. of design limit load during the combined unbending and torsion ultimate design load test. It appears that the failure initiated at a stiffener runout location in the upper cover which resulted in rupture of the upper cover and portions of both spars.

Griffin, C. F.↗
NASA NTRS1992

Structural testing of the technology integration box beam

A full-scale section of a transport aircraft wing box was designed, analyzed, fabricated, and tested. The wing box section, which was called the technology integration box beam, contained blade stiffened covers and T-stiffened channel spars constructed using graphite/epoxy materials. Covers, spars, and the aluminum ribs were assembled using mechanical fasteners. The box beam was statically tested for several loading conditions to verify the stiffness and strength characteristics of the composite wing design. Failure of the box beam occurred at 125 percent of design limit load during the combined upbending and torsion ultimate design load test. It appears that the failure initiated at a stiffener runout location in the upper cover which resulted in rupture of the upper cover and portions of both spars.

Griffin, C. F.↗
NASA NTRS2004

Suggested Procedures for Installing Strain Gauges on Langley Research Center Wind Tunnel Balances, Custom Force Measuring Transducers, Metallic and Composite Structural Test Articles

The character of force and strain measurement testing at LaRC is such that the types of strain gauge installations, the materials upon which the strain gauges are applied, and the test environments encountered, require many varied approaches. In 1997, a NASA Technical Memorandum (NASA TM 110327) was generated to provide the strain gauge application specialist with a listing of recommended procedures for strain gauging various transducers and test articles at LaRC. The technical memorandum offered here is an effort to keep the strain gauge user informed of new technological enhancements in strain-gauging methodology while preserving the strain-gauging guidelines set forth in the 1997 TM. This document provides detailed recommendations for strain gauging LaRC-designed balances and custom transducers, composite materials, cryogenic and high-temperature test articles, and selected non-typical or unique materials or test conditions. Additionally, one section offers details for installing Bragg-Grating type fiber-optic strain sensors for non-typical test scenarios.

Moore, Thomas C., Sr.↗