Search NASA⌕ Search

SEARCH · Search NASA

Results for “ether”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Disulfonated Poly(arylene ether sulfone) Random Copolymers Containing Hierarchical Iptycene Units for Proton Exchange Membranes

Two series of disulfonated iptycene-based poly(arylene ether sulfone) random copolymers, i.e., TRP-BP (triptycene-based) and PENT-BP (pentiptycene-based), were synthesized via condensation polymerization from disulfonated monomer and comonomers to prepare proton exchange membranes (PEMs) for potential applications in electrochemical devices such as fuel cell. To investigate the effect of iptycene units on membrane performance, these copolymers were systematically varied in composition (i.e., iptycene content) and the degree of sulfonation (i.e., 30–50%), which were characterized comprehensively in terms of water uptake, swelling ratio, oxidative stability, thermal and mechanical properties, and proton conductivity at various temperatures. Comparing to copolymers without iptycene units, TRP-BP and PENT-BP ionomers showed greatly enhanced thermal and oxidative stabilities due to strong intra- and inter-molecular supramolecular interactions induced by hierarchical iptycene units. In addition, the introduction of iptycene units in general provides PEMs with exceptional dimensional stability of low volume swelling ratio at high water uptakes, which is ascribed to the supramolecularly interlocked structure as well as high fractional free volume of iptycene-based polymers. It is demonstrated that the combination of high proton conductivity and good membrane dimension stability is the result of the synergistic effects of multiple factors including free volume (iptycene content), sulfonation degree, hydrophobicity, and swelling behavior (supramolecular interactions).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Light Duty Engine Performance Characteristics with Dimethyl Ether and Propane

Here, this paper explores the performance characteristics of a compression ignition HYUNDAI 2.2L engine operating with Dimethyl Ether (DME). Test are carried out at three operating conditions that weigh heavily in the FTP75 certification cycle (1000rpm-12Nm, 1500rpm-50Nm, 2000rpm-100Nm). The engine features a high-pressure common rail fuel injection system designed to operate with liquified gases. The main component of the fuel system is a high-pressure pump that incorporates an electronic inlet metering valve commanded on a crank-angle base to control the rail pressure. The pump, which requires no pressure regulator, provides the flow needed to the injectors without flow returning to the inlet. This novel fueling system is leveraged in tests that are conducted to examine the impact of EGR, combustion phasing, injection pressure on efficiency and emissions. In addition, the impact of introducing 15% Propane by mass is examined. During the tests, the engine ECU is aided by an Engine Controller High Speed Oversight unit (ECHO) to provide combustion phasing control, improved cylinder-to-cylinder uniformity, and an effective optimization over the testing effort. The use of DME and Propane allowed for peak thermal efficiency of nearly 43%. These fuels enable significant carbon index (CI) reductions over the baseline Diesel fuel, with indications that 50% reduction in CO 2 over the Diesel engine are possible.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Extraction of Value-Added Products from Food Processing Waste Using Dimethyl Ether

Poster for 2024 Intern Poster Session. Food production waste can be valorized to create a circular economy. Traditional extraction methods require pretreatment of the sample through heating or cell disruption, but this contributes to a majority of the process's energy usage for wet biomass. Using dimethyl ether extraction can combine the dewatering and extraction processes into one to skip the pretreatment step while still maintaining similar extraction rates.

09 BIOMASS FUELS↗
DOE OSTI2024

Extraction of Value-Added Products From Food Processing Waste Using Liquid Dimethyl Ether

Technical presentation for 2024 Intern Poster Session. Food production waste can be valorized to create a circular economy. Traditional extraction methods require pretreatment of the sample through heating or cell disruption, but this contributes to a majority of the process's energy usage for wet biomass. Using dimethyl ether extraction can combine the dewatering and extraction processes into one to skip the pretreatment step while still maintaining similar extraction rates.

09 BIOMASS FUELS↗
DOE OSTI2025

Extraction of Oil From Camelina Seeds Using Liquefied Dimethyl Ether

With a changing climate and a push for net-zero carbon emissions, sustainable aviation fuel (SAF) is gaining interest worldwide. Due to its compatibility with current infrastructure and potential to reduce emissions by up to 94%, SAF has been identified as the best near-term opportunity to decrease carbon emissions in the aviation industry. SAF can be produced from various renewable feedstocks, with Camelina sativa (L.) seeds standing out due to their high oil content. Conventionally, the oil is extracted using hydrothermal liquefaction (HTL), which involves the pressurized heating of water and biomass up to 400°C, making it incredibly energy-intensive. Conversely, liquefied dimethyl ether (DME) extraction operates at room temperature and is capable of near 100% solvent recycling. In this work, we propose the use of DME extraction as a substitute for HTL, hypothesizing that it can overcome the challenges of current oil extraction methods while maintaining the same oil yields.

09 - BIOMASS FUELS↗
DOE OSTI2024

Enhancing Cycling Stability of Lithium Metal Batteries by a Bifunctional Fluorinated Ether

Abstract The lifespan of lithium (Li) metal batteries (LMBs) can be greatly improved by the formation of inorganic‐rich electrode‐electrolyte interphases (EEIs) (including solid‐electrolyte interphase on anode and cathode‐electrolyte interphase on cathode). In this work, a localized high‐concentration electrolyte containing lithium bis(fluorosulfonyl)imide (LiFSI) salt, 1,2‐dimethoxyethane (DME) solvent and 1,2‐bis(1,1,2,2‐tetrafluoroethoxy)ethane (BTFEE) diluent is optimized. BTFEE is a fluorinated ether with weakly‐solvating ability for LiFSI so it also acts as a co‐solvent in this electrolyte. It can facilitate anion decomposition at electrode surfaces and promote the formation of more inorganic‐rich EEI layers. With an optimized molar ratio of LiFSI:DME:BTFEE = 1:1.15:3, LMBs with a high loading (4 mAh cm −2 ) lithium nickel manganese cobalt oxide (LiNi 0.8 Mn 0.1 Co 0.1 ) cathode can retain 80% capacity in 470 cycles when cycled in a voltage range of 2.8–4.4 V. The fundamental understanding on the functionality of BTFEE revealed in this work provides new perspectives on the design of practical high‐energy density battery systems.

25 ENERGY STORAGE↗
DOE OSTI2021

Roles of interaction between components in CZZA/HZSM-5 catalyst for dimethyl ether synthesis via CO 2 hydrogenation

The roles of interaction between two catalyst components in CuO–ZnO–ZrO 2 –Al 2 O 3 (CZZA)/HZSM-5 bifunctional catalyst for dimethyl ether (DME) synthesis via carbon dioxide hydrogenation were investigated. It was found that CZZA catalyst showed excellent stability during methanol (MeOH) synthesis for 100 h, while there was a severe loss of catalytic activity in the bifunctional catalyst for DME synthesis. So, the effects of different degrees of intimacy of two catalyst components were studied for DME synthesis, including mixed and separated modes. For the mixed mode, the particle size of catalysts and the amount of reaction intermediates were proven to influence the catalyst deactivation. For the separated mode, the catalysts showed rapid deactivation within a short time. Various characterizations indicated that the remarkable deactivation of separated mode was mainly caused by the decrease of copper active centers (e.g., sintering and oxidation) and blockage of acid sites via increased coke deposition on HZSM-5.

42 ENGINEERING↗
DOE OSTI2022

Controlling Reaction Routes in Noble‐Metal‐Catalyzed Conversion of Aryl Ethers

Abstract Hydrogenolysis and hydrolysis of aryl ethers in the liquid phase are important reactions for accessing functionalized cyclic compounds from renewable feedstocks. On supported noble metals, hydrogenolysis is initiated by a hydrogen addition to the aromatic ring followed by C−O bond cleavage. In water, hydrolysis and hydrogenolysis proceed by partial hydrogenation of the aromatic ring prior to water or hydrogen insertion. The mechanisms are common for the studied metals, but the selectivity to hydrogenolysis increases in the order Pd 2 pressure, thus, the selectivity to hydrogenolysis is maximized by increasing temperature and decreasing H 2 pressure. Selectivity to C−O bond cleavage reaches >95 % in water and alkaline conditions.

Schmid, Julian↗
DOE OSTI2022

Superior Metal‐Organic Framework Activation with Dimethyl Ether

Abstract Metal–organic frameworks (MOFs) are demonstrated to be readily activated by treatment with the low surface tension, low boiling point solvent dimethyl ether (DME). The mildness of the method enables access to high surface areas by avoiding structural changes in the framework that often plague thermal activation methods. A distinction from previous methods is that DME activation succeeds for materials with coordinatively unsaturated sites (CUS) and non‐CUS MOFs as well. DME displaces solvent molecules occupying the pores of the MOF as well as those coordinated to metal centers; reducing evacuation temperature by using a coordinating, yet highly volatile guest enables low temperature activation with structural retention as demonstrated surface area measurements that match or exceed existing activation protocols.

Wright, Keenan R.↗
DOE OSTI2023

High‐Performance Lithium Metal Batteries Enabled by a Fluorinated Cyclic Ether with a Low Reduction Potential

Abstract Electrolyte engineering is crucial for developing high‐performance lithium metal batteries (LMB). Here, we synthesized two cosolvents methyl bis(fluorosulfonyl)imide (MFSI) and 3,3,4,4‐tetrafluorotetrahydrofuran (TFF) with significantly different reduction potentials and add them into LiFSI‐DME electrolytes. The LiFSI/TFF‐DME electrolyte gave an average Li Coulombic efficiency (CE) of 99.41 % over 200 cycles, while the average Li CEs for MFSI‐based electrolyte is only 98.62 %. Additionally, the TFF‐based electrolytes exhibited a more reversible performance than the state‐of‐the‐art fluorinated 1,4‐dimethoxylbutane electrolyte in both Li||Cu half‐cell and anode‐free Cu||LiNi 0.8 Mn 0.1 Co 0.1 O 2 full cell. More importantly, the decomposition product from bis(fluorosulfonyl)imide anion could react with ether solvent, which destroyed the SEI, thus decreasing cell performance. These key discoveries provide new insights into the rational design of electrolyte solvents and cosolvents for LMB.

Wu, Min↗
DOE OSTI2022

Controlling Reaction Routes in Noble‐Metal‐Catalyzed Conversion of Aryl Ethers

Abstract Hydrogenolysis and hydrolysis of aryl ethers in the liquid phase are important reactions for accessing functionalized cyclic compounds from renewable feedstocks. On supported noble metals, hydrogenolysis is initiated by a hydrogen addition to the aromatic ring followed by C−O bond cleavage. In water, hydrolysis and hydrogenolysis proceed by partial hydrogenation of the aromatic ring prior to water or hydrogen insertion. The mechanisms are common for the studied metals, but the selectivity to hydrogenolysis increases in the order Pd 2 pressure, thus, the selectivity to hydrogenolysis is maximized by increasing temperature and decreasing H 2 pressure. Selectivity to C−O bond cleavage reaches >95 % in water and alkaline conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Superior Metal‐Organic Framework Activation with Dimethyl Ether

Abstract Metal–organic frameworks (MOFs) are demonstrated to be readily activated by treatment with the low surface tension, low boiling point solvent dimethyl ether (DME). The mildness of the method enables access to high surface areas by avoiding structural changes in the framework that often plague thermal activation methods. A distinction from previous methods is that DME activation succeeds for materials with coordinatively unsaturated sites (CUS) and non‐CUS MOFs as well. DME displaces solvent molecules occupying the pores of the MOF as well as those coordinated to metal centers; reducing evacuation temperature by using a coordinating, yet highly volatile guest enables low temperature activation with structural retention as demonstrated surface area measurements that match or exceed existing activation protocols.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Application of Poly(ether sulfone)‐Based Membranes in Clean Energy Technology

Abstract Poly(ether sulfone) (PES) is a kind of polymer materials with excellent electrical insulation and acid/alkali stability. PES can be operated at high temperature continuously for a long time and still maintain excellent property stability in the environments with rapidly changed temperature, namely, great thermostability. Moreover, PES has low molding shrinkage, good dimensional stability and excellent film‐forming characteristics. Compared with inorganic membranes, PES‐based membranes have lower cost, which have received more attention and wide recognition in the field of clean energy technologies in recent years, such as flow batteries, fuel cells, water treatment, and gas separation. Therefore, this review summarizes the research status and prospect of the utilization of PES‐based membranes in clean energy fields, in order to further promote their development and application.

Chemistry↗
DOE OSTI2022

A separations and purification process for improving yields and meeting fuel contaminant specifications for high-octane gasoline produced from dimethyl-ether over a Cu/BEA catalyst

In this work, we have been developing a three-step conversion of biomass-derived syngas to methanol to dimethyl-ether (DME) to non-aromatic hydrocarbons for use as high-octane gasoline and sustainable aviation fuel. This process produces branched alkanes from DME using a Cu/BEA catalyst and is a promising alternative to other syngas conversion processes such as Fischer-Tropsch to linear alkanes and traditional ZSM-5 catalyzed methanol to aromatic gasoline. In this short article we describe some advances in our understanding related to separations and purification via the use of more detailed experimental speciation in an updated process model involving multiple phase equilibrium-based separation steps. Primary modeled reactor outlet constituents (and weight %) are: C3 and lighter hydrocarbon gases (11.1%), C4s (54.5%), H 2 (1.2%), CO 2 (2.9%), water (5.0%), unreacted DME (16.5%), methanol (2.3%), and C5+ hydrocarbons (6.4%). DME (the primary reactant) and H 2 recycle and reuse are important for the overall process efficiency, and the recycle of C4s is important to increase the C5+ yield via reactivation and homologation. Thus H 2 , C4s, and DME are targeted for recycle, while methanol and water need to be removed from the product to conform with fuel specifications. Model predictions from Aspen Plus using the NRTL-RK property method indicate a fuel composition with C5+ content of 97.1 wt%, with minor constituents: 2.4 wt% C4s, 0.3 wt% methanol, 0.1 wt% DME, 0.03 wt% water, and 0.01 wt% C3s. These ranges of minor components conform with fuel quality requirements, and the modeled product is amenable for unconstrained blending to boost gasoline octane ratings.

09 BIOMASS FUELS↗
DOE OSTI2022

Elucidating the Reaction Pathways of Veratrylglycero-β-Guaiacyl Ether Degradation over Metal-Free Solid Acid Catalyst with Hydrogen

Efficient cleavage of β-O-4 bonds in lignin to high-yield aromatic compounds for the potential production of fuels and chemicals is vital for the economics of the modern biorefinery industry. This work is distinct in that a detailed mechanistic analysis of the reaction pathways of veratrylglycero-β-guaiacyl ether (VGE) catalyzed by transition-metal-free solid acid zeolite in aqueous conditions at high hydrogen pressure has been performed. VGE degradation produced high monomers yields (≈87 %), including guaiacol (48.2 %), 1-(3,4-dimethoxyphenyl)ethanol (10.3 %), 1-(3,4-dimethoxyphenyl)-2-propanol (6.1 %), 3,4-dimethoxyphenylpropanol (4.7 %), 3,4-dimethoxycinnamyl alcohol (4.1 %), and 1,2-dimethoxy-4-propylbenzene (2 %). The products were identified and confirmed by the in situ solid-state magic angle spinning (MAS) 13 C NMR spectroscopy in real-time conditions and the two-dimensional gas chromatography (GC×GC). A variety of products reveal the crucial role of hydrogen, water, and acid sites for heterolytic cleavage of the β-O-4 bond in VGE. Decarbonylation, hydrogenolysis, hydrogenation, and dehydration reaction pathways are proposed and further validated using first-principles calculations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Rheological behavior of neat and carbon fiber-reinforced poly(ether ketone ketone) for extrusion deposition additive manufacturing

To develop new materials for extrusion additive manufacturing (AM) systems, a fundamental understanding of rheological properties is essential to correlate the effect of processing on material structure and its properties. In this work, the rheological properties of five different grades of neat and carbon fiber (CF)-reinforced poly(ether ketone ketone) are reported. Rheological properties are essential to understand the effect of reinforcing fibers and AM process parameters such as time, temperature, environment, and shear rate on flow behavior during processing. Small-amplitude oscillatory shear tests and steady shear tests indicated neat grades to exhibit less increase in viscosity over time when processed in air than the CF-filled grades. The filled grades showed greater shear thinning and lower sensitivity to temperature. Altogether, this rheological analysis provides a broad framework for determining appropriate processing conditions for extrusion deposition AM of such high-temperature polymer systems.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Model-based optimization strategies for direct hydrogenation of carbon dioxide to dimethyl ether

Here, this study discusses model-based optimization strategies for CO 2 hydrogenation to dimethyl ether (DME) over aCuZnZr (CZZ) and ferrite (FER) mixed catalyst system in a packed-bed reactor configuration. A two-dimensional axisymmetric, nonisothermal packed-bed reactor model was developed using COMSOL Multiphysics 6.2 software. The model solves two-dimensional (radial and axial) heat and mass transport equations in the packed-bed and integrates intraparticle diffusion and heat transfer in a 1D approach. This powerful feature differs from a traditional porous media approach and takes into account any heat and mass transfer limitations that may exist. Analysis shows that the heat transfer limitations are negligible, but strong internal mass transfer limitations were observed at 10 ≤ WHSV ≤ 90 h -1 on the FER catalyst and at 240 °C. The optimum catalyst composition (i.e., mixing ratio) varies depending on the operating regime. The FER catalyst weight in the mixture can be as low as 5 wt.%, but the ideal composition de-pends on the internal mass transfer limitation and its relationship with the operating regime (i.e., weight hourly space velocity, temperature). A catalyst composition of 80 wt.% CZZ and 20 wt.% FER was suggested; this composition can provide high CO 2 conversion and DME production rates at a wide range of temperatures and flow rates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

The first experimental evidence for improved nanomechanical properties of calcium silicate hydrate by polycarboxylate ether and graphene oxide

Graphene oxide (GO) efficiently enhances macroscale mechanical properties of cement-based materials. Yet the nanoscale reinforcing mechanism of GO for calcium silicate hydrate (C-S-H), the key binding phase of concrete, remains poorly understood. Moreover, how polycarboxylate ether (PCE)-based superplasticizers affect the nanomechanical properties of C-S-H remains unclear. The intrinsic mechanical properties of the nanocomposites are measured using high-pressure X-ray diffraction. The influences of GO and PCE on the local Ca and Si environments are probed using X-ray absorption spectroscopy. For the first time, we evidence that PCE-induced well-dispersed GO nanoplatelets strengthen the C-S-H basal planes, whereas poorly water-dispersed GO weakly interacts with basal planes and does not strengthen in plane Casingle bondO bonds. Both PCE and GO only slightly strengthen C-S-H's c-axis. Here, the bulk modulus of C-S-H/PCE/GO nanocomposite is 190% than pure C-S-H. Functional groups of PCE and GO prefer interacting with the Casingle bondO sheets of C-S-Hs instead of silicate tetrahedra.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗