Search NASA⌕ Search

SEARCH · Search NASA

Results for “high speed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Computational Analyses of the LIMX TBCC Inlet High-Speed Flowpath

Reynolds-Averaged Navier-Stokes (RANS) simulations were performed for the high-speed flowpath and isolator of a dual-flowpath Turbine-Based Combined-Cycle (TBCC) inlet using the Wind-US code. The RANS simulations were performed in preparation for the Large-scale Inlet for Mode Transition (LIMX) model tests in the NASA Glenn Research Center (GRC) 10- by 10-ft Supersonic Wind Tunnel. The LIMX inlet has a low-speed flowpath that is coupled to a turbine engine and a high-speed flowpath designed to be coupled to a Dual-Mode Scramjet (DMSJ) combustor. These RANS simulations were conducted at a simulated freestream Mach number of 4.0, which is the nominal Mach number for the planned wind tunnel testing with the LIMX model. For the simulation results presented in this paper, the back pressure, cowl angles, and freestream Mach number were each varied to assess the performance and robustness of the high-speed inlet and isolator. Under simulated wind tunnel conditions at maximum inlet mass flow rates, the high-speed flowpath pressure rise was found to be greater than a factor of four. Furthermore, at a simulated freestream Mach number of 4.0, the high-speed flowpath and isolator showed stability for freestream Mach number that drops 0.1 Mach below the design point. The RANS simulations indicate the yet-untested highspeed inlet and isolator flowpath should operate as designed. The RANS simulation results also provided important insight to researchers as they developed test plans for the LIMX experiment in GRC s 10- by 10-ft Supersonic Wind Tunnel.

Dippold, Vance F., III↗
NASA NTRS1992

Turbulence modeling for high speed flows

An investigation of turbulence models for high speed flows is presented. The flows consist of simple 2D flows over flat plates and complex shock-wave boundary-layer interaction flows over ramps and wedges. The flows are typical of those encountered by high speed vehicles such as the NASP. The turbulence models investigated include various two-equation models which, as a class, are considered to be well suited to the design of high speed vehicles. A description and discussion of the specific models is given and includes both baseline or uncorrected models, and model corrections which are needed to improve predictions of complex flows. It is found that most of the models studied are able to give good predictions of the flat plate flows, and some of the models are able to predict some of the complex flows, but none of them are able to accurately predict all of the complex flows. Recommendations for future model improvements are discussed.

Coakley, T. J.↗
NASA NTRS1999

1995 NASA High-Speed Research Program Sonic Boom Workshop: Configuration Design, Analysis, and Testing - Volume 2

The High-Speed Research Program and NASA Langley Research Center sponsored the NASA High-Speed Research Program Sonic Boom Workshop on September 12-13, 1995. The workshop was designed to bring together NASAs scientists and engineers and their counterparts in industry, other Government agencies, and academia working together in the sonic boom element of NASAs High-Speed Research Program. Specific objectives of this workshop were to: (1) report the progress and status of research in sonic boom propagation, acceptability, and design; (2) promote and disseminate this technology within the appropriate technical communities; (3) help promote synergy among the scientists working in the Program; and (4) identify technology pacing, the development C, of viable reduced-boom High-Speed Civil Transport concepts. The Workshop was organized in four sessions: Sessions 1 Sonic Boom Propagation (Theoretical); Session 2 Sonic Boom Propagation (Experimental); Session 3 Acceptability Studies-Human and Animal; and Session 4 - Configuration Design, Analysis, and Testing.

High-speed research↗
NASA NTRS1992

First Annual High-Speed Research Workshop, part 3

The First High-Speed Research (HSR) Workshop was hosted by NASA LaRC and was held 14-16 May 1991, in Williamsburg, Virginia. The purpose of the workshop was to provide a national forum for the government, industry, and university participants to present and discuss important technology issues related to the development of a commercially viable, environmentally compatible, U.S. High-Speed Civil Transport. The workshop sessions are organized around the major task elements in NASA's Phase 1 High-Speed Research Program which basically addresses the environmental issues of atmospheric emissions, community noise, and sonic boom.

Whitehead, Allen H., Jr.↗
NASA NTRS1990

Control of a GaAs monolithic Ka-band phase shifter using a high-speed optical interconnect

The use of a high-speed optical interconnect in the control of a Ka-band GaAs monolithic phase shifter is described. A 16-b serial control signal was used to modulate the output of a laser transmitter, and the transmitted optical signal was detected and demultiplexed into 16 parallel electrical outputs using a high-speed hybrid GaAs optoelectronic integrated circuit. Four of the parallel output lines were interfaced to the 4-b phase shifter, and high-speed, optically controlled switching of the phase shifter was observed at clock frequencies to 30 MHz using an interferometric technique.

Bhasin, K. B.↗
NASA NTRS1995

Radiation safety aspects of commercial high-speed flight transportation

High-speed commercial flight transportation is being studied for intercontinental operations in the 21st century, the projected operational characteristics for these aircraft are examined, the radiation environment as it is now known is presented, and the relevant health issues are discussed. Based on a critical examination of the data, a number of specific issues need to be addressed to ensure an adequate knowledge of the ionizing radiation health risks of these aircraft operations. Large uncertainties in our knowledge of the physical fields for high-energy neutrons and multiply-charged ion components need to be reduced. Improved methods for estimating risks in prenatal exposure need to be developed. A firm basis for solar flare monitoring and forecasting needs to be developed with means of exposure abatement.

Wilson, John W.↗
NASA NTRS1984

A High-speed Characterization Technique for Solar Silicon

High-speed crystal growth techniques demand high-speed characterization techniques to allow a timely feed-back of information to the crystal growers. The unique properties of the Si electrolyte-contact (SEC) provide for an extremely fast and simple measurement of the light-induced photo-current for any piece of Si without lengthy preparation of the specimen. Electropolishing at high anodic current densities allows for insitu generation of fresh surfaces whereas preferential etching of defects in various modes is possible at low current densities. In n-type Si a simple estimation of the minority-carrier diffusion length is possible in many cases. Laser-scanning enables local probing of the photocurrent and provides data about the homogeneity of a sample. The experimental realization of the method is described in detail and examples are given and discussed.

Lehmann, V.↗
NASA NTRS1992

Observation of alloy solidification using high-speed video

A high-speed video instrumentation system was used to observe solidification of undercooled Ti-51 at. pct Al. The camera system developed by Battelle is capable of operation at rates up to 12,000 frames per second. The system digitizes and stores video images acquired by a 64 x 64 pixel silicon photodiode array. In a joint effort with Vanderbilt University the camera was used to observe three transformations of the undercooled alloys, using containerless processing by electromagnetic levitation. The first was solidification where nucleation was induced at an undercooling of 9 percent Tl, where Tl is the liquidus temperature of the alloy, and the second was solidification where nucleation was spontaneous at an undercooling of 15 percent Tl. The third event was a solid-state nucleation and growth transformation following the solidification at an undercooling of 15 percent Tl.

Bassler, B. T.↗
NASA NTRS1953

Preliminary Comparison of 17- and 75-millimeter-bore Cageless Cylindrical Roller Bearings with Conventional Cylindrical Roller Bearings at High Speeds

Preliminary results at high speeds indicate lower bearing temperatures, less internal bearing wear, and greater reliability of the conventional, cage-type cylindrical roller bearings than of either full-complement or special cageless roller bearings of the types investigated, although the latter bearing types have been operated successfully to DN values of 1.0 X 10 superscript 6.

BEARINGS, ANTIFRICTION↗
NASA NTRS1990

Suggested future directions in high-speed transition experimental research

Historical developments in the area of high-speed experimental transition research are outlined, and future directions in this area as determined by the panel membership are listed. The directions include measurement and modeling of initial disturbance fields, both in ground facilities and flight, for all modes; development of advanced high-speed instrumentation for disturbance field measurements, measurements of the details of receptivity in multitudinous flows; further development and use of high-speed quiet tunnels; stability and transition studies for multitudinous flows; detailed studies of the transitional region for boundary layers, free flows, vortices separated flows, corner flows, etc.; and studies of flow-chemistry effects on transition phenomena. Applied research such areas as the physics of perforated-surface suction stabilization and the resolution of anomalies in the existing high-speed database is also suggested.

Bushnell, Dennis↗
NASA NTRS1987

Design Considerations for High-Speed Control Systems

Existing hardware integrated into versatile, high-speed control system. Report discusses five global design considerations to integrate array-processor, multimicroprocessor, and host-computer system architectures into versatile, high-speed controllers. Such controllers are capable of control throughputs as high as 36 MHz for 8-bit bytes and maintain constant interaction with non-real-time or user environment. Application example, architecture of high-speed, closed-loop controller used to control helicopter vibration actively discussed.

Jacklin, S. A.↗
NASA NTRS1991

High-speed rotorcraft propulsion

Recently completed high-speed rotorcraft design studies for NASA provide the basis to assess technology needs for the development of these aircraft. Preliminary analysis of several concepts possessing helicopter-like hover characteristics and cruise capabilities in the 450 knot regime, led to the selection of two concepts for further study. The concepts selected included the Rotor/Wing and the Tilt Wing. The two unique concepts use turbofan and turboshaft engines respectively. Designs, based on current technology for each, established a baseline configuration from which technology trade studies could be conducted. Propulsion technology goals from the IHPTET program established the advanced technolgy year. Due to high-speed requirements, each concept possesses its own unique propulsion challenges. Trade studies indicate that achieving th IHPTET Phase III goals significantly improves the effectiveness of both concepts. Increased engine efficiency is particularly important to VTOL aircraft by reducing gross weight.

Rutherford, John W.↗
NASA NTRS1981

Advanced superposition methods for high speed turbopump vibration analysis

The small, high pressure Mark 48 liquid hydrogen turbopump was analyzed and dynamically tested to determine the cause of high speed vibration at an operating speed of 92,400 rpm. This approaches the design point operating speed of 95,000 rpm. The initial dynamic analysis in the design stage and subsequent further analysis of the rotor only dynamics failed to predict the vibration characteristics found during testing. An advanced procedure for dynamics analysis was used in this investigation. The procedure involves developing accurate dynamic models of the rotor assembly and casing assembly by finite element analysis. The dynamically instrumented assemblies are independently rap tested to verify the analytical models. The verified models are then combined by modal superposition techniques to develop a completed turbopump model where dynamic characteristics are determined. The results of the dynamic testing and analysis obtained are presented and methods of moving the high speed vibration characteristics to speeds above the operating range are recommended. Recommendations for use of these advanced dynamic analysis procedures during initial design phases are given.

Nielson, C. E.↗