Search NASA⌕ Search

SEARCH · Search NASA

Results for “polyurethane”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

The corrosion protection of 6061-T6 aluminum by a polyurethane-sealed anodized coat

The corrosion protection of 6061-T6 anodized aluminum afforded by a newly patented polyurethane seal was studied using the ac impedance technique. Values of the average corrosion rates over a 27-day exposure period in 3.5 percent NaCl solutions at pH 5.2 and pH 9.5 compared very favorably for Lockheed-prepared polyurethane-sealed and dichromate-sealed coats of the same thickness. Average corrosion rates for both specimens over the first 7 days of exposure compared well with those for a hard anodized, dichromate-sealed coat, but rose well above those for the hard anodized coat over the entire 27-day period. This is attributed both to the greater thickness of the hard anodized coat, and possibly to its inherently better corrosion protective capability.

Danford, M. D.↗

Tests Of Polyurethane And Dichromate Coats On Aluminum

Report describes experiments to determine relative effectiveness of new polyurethane and more-conventional dichromate coat in helping to retard corrosion of anodized 6061-T6 aluminum. Concludes by suggesting greater protection against corrosion achieved by combining polyurethane-sealing method with hard-anodizing method and by increasing thickness of coat.

Danford, M. D.↗

Thermal Performance of Aircraft Polyurethane Seat Cushions

Aircraft seat materials were evaluated in terms of their thermal performance. The materials were evaluated using (a) thermogravimetric analysis, (b) differential scanning calorimetry, (c) a modified NBS smoke chamber to determine the rate of mass loss and (d) the NASA T-3 apparatus to determine the thermal efficiency. In this paper, the modified NBS smoke chamber will be described in detail since it provided the most conclusive results. The NBS smoke chamber was modified to measure the weight loss of material when exposed to a radiant heat source over the range of 2.5 to 7.5 W/sq cm. This chamber has been utilized to evaluate the thermal performance of various heat blocking layers utilized to protect the polyurethane cushioning foam used in aircraft seats. Various kinds of heat blocking layers were evaluated by monitoring the weight loss of miniature seat cushions when exposed to the radiant heat. The effectiveness of aluminized heat blocking systems was demonstrated when compared to conventional heat blocking layers such as neoprene. All heat blocking systems showed good fire protection capabilities when compared to the state-of-the-art, i.e., wool-nylon over polyurethane foam.

Kourtides, D. A.↗

An Improved Thermal Conductivity Polyurethane Composite for a Space Borne 20KV Power Supply

This effort was designed to find a way to reduce the temperature rise of critical components of a 20KV High Voltage Power Supply (HVPS) by improving the overall thermal conductivity of the encapsulated modules. Three strategies were evaluated by developing complete procedures, preparing samples, and performing tests. The three strategies were: 1. Improve the thermal conductivity of the polyurethane encapsulant through the addition of thermally conductive powder while minimizing impact on other characteristics of the encapsulant. 2. Improve the thermal conductivity of the polyurethane encapsulated assembly by the addition of a slab of thermally conductive, electrically insulating material, which is to act as a heat spreader. 3. Employ a more thermally conductive substrate (Al203) with the existing encapsulation scheme. The materials were chosen based on the following criteria: high dielectric breakdown strength; high thermal conductivity, ease of manufacturing, high compliance, and other standard space qualified materials properties (low out-gassing, etc.). An optimized cure was determined by a statistical design of experiments for both filled and unfilled materials. The materials were characterized for the desired properties and a complete process was developed and tested. The thermal performance was substantially improved and the strategies may be used for space flight.

Pb free↗

Joint Test Report For Validation of Alternatives to Aliphatic Isocyanate Polyurethanes

National Aeronautics and Space Administration (NASA) and Air Force Space Command (AFSPC) have similar missions and therefore similar facilities and structures in similar environments. The standard practice for protecting metallic substrates in atmospheric environments is the application of an applied coating system. The most common topcoats used in coating systems are polyurethanes that contain isocyanates. Isocyanates are classified as potential human carcinogens and are known to cause cancer in animals. The primary objective of this effort was to demonstrate and validate alternatives to aliphatic isocyanate polyurethanes resulting in one or more isocyanate-free coatings qualified for use at AFSPC and NASA installations participating in this project. This joint Test Report (JTR) documents the results of the laboratory and field testing as well as any test modifications made during the execution of the testing. The technical stakeholders agreed upon test procedure modifications documented in this document. This JTR is made available as a reference for future pollution prevention endeavors by other NASA centers, the Department of Defense and commercial users to minimize duplication of effort. All coating system candidates were tested using approved NASA and AFSPC standard coating systems as experimental controls. This study looked at eight alternative coating systems and two control coating systems and was divided into Phase I Screening Tests, Phase II Tests, and Field Testing. The Phase I Screening Tests were preliminary tests performed on all the selected candidate coating systems. Candidate coating systems that did not meet the acceptance criteria of the screening tests were eliminated from further testing. Phase I Screening Tests included: Ease of Application, Surface Appearance, Dry-To-Touch (Sanding), Accelerated Storage Stability, Pot Life (Viscosity), Cure Time (Solvent Rubs), Cleanability, Knife Test, Tensile (pull-off) Adhesion, and X-Cut Adhesion by Wet Tape After a review of the Phase I test results, four of the alternative coating systems showed substandard performance in relation to the Control Systems and were eliminated from the Phase II testing. Due to the interest of stakeholders and time constraints, however, all eight alternatives were subjected to the following Phase II tests, along with field testing at Stennis Space Center (SSC), Mississippi: Hypergol Compatibility, Liquid Oxygen Compatibility, 18-Month Marine Exposure (Gloss Retention, Color Retention, Blistering, Visual Corrosion, Creepage from Scribe, Heat Adhesion), and Field Exposure (6- and 12-month Evaluation for Coating Condition, Color Retention, Gloss Retention). The remaining four alternative coating systems determined to be the best viable alternatives were carried on to Phase II testing that included: Removability, Repairability, Abrasion Resistance, Gravelometer, Fungus Resistance, Accelerated Weathering, Mandrel Bend Flexibility, and Cyclic Corrosion Resistance. Of the systems that continued to Phase II, three (3) alternative coating systems meet the performance requirements as identified by stakeholders. Two (2) other systems, that were not included in Phase II testing, performed well enough on the 18-Month Marine Exposure, the primary requirement for NASA technical standard NASA-STD-5008, Protective Coating of Carbon Steel, Stainless Steel, and Aluminum on Launch Structures, Facilities, and Ground Support Equipment, that they were also considered to be successful candidates. In total, five (5) alternative coating systems were approved for inclusion in the NASA-STD- 5008 Qualified Products List (QPL). The standard is intended to provide a common framework for consistent practices across NASA and is often used by other entities. The standard's QPL does not connote endorsement of the products by NASA, but lists those products that have been tested and meet the requirements as specified.

Lewis, Pattie↗

A finite element/level set model of polyurethane foam expansion and polymerization

Polyurethane foams are used widely for encapsulation and structural purposes because they are inexpensive, straightforward to process, amenable to a wide range of density variations (1 lb/ft3 - 50 lb/ft3), and able to fill complex molds quickly and effectively. Computational model of the filling and curing process are needed to reduce defects such as voids, out-of-specification density, density gradients, foam decomposition from high temperatures due to exotherms, and incomplete filling. This paper details the development of a computational fluid dynamics model of a moderate density PMDI structural foam, PMDI-10. PMDI is an isocyanate-based polyurethane foam, which is chemically blown with water. The polyol reacts with isocyanate to produces the polymer. PMDI- 10 is catalyzed giving it a short pot life: it foams and polymerizes to a solid within 5 minutes during normal processing. To achieve a higher density, the foam is over-packed to twice or more of its free rise density of 10 lb/ft3. The goal for modeling is to represent the expansion, filling of molds, and the polymerization of the foam. This will be used to reduce defects, optimize the mold design, troubleshoot the processed, and predict the final foam properties. A homogenized continuum model foaming and curing was developed based on reaction kinetics, documented in a recent paper; it uses a simplified mathematical formalism that decouples these two reactions. The chemo-rheology of PMDI is measured experimentally and fit to a generalized- Newtonian viscosity model that is dependent on the extent of cure, gas fraction, and temperature. The conservation equations, including the equations of motion, an energy balance, and three rate equations are solved via a stabilized finite element method. The equations are combined with a level set method to determine the location of the foam-gas interface as it evolves to fill the mold. Understanding the thermal history and loads on the foam due to exothermicity and oven curing is very important to the results, since the kinetics, viscosity, and other material properties are all sensitive to temperature. Results from the model are compared to experimental flow visualization data and post-test X-ray computed tomography (CT) data for the density. Several geometries are investigated including two configurations of a mock structural part and a bar geometry to specifically test the density model. We have found that the model predicts both average density and filling profiles well. However, it under predicts density gradients, especially in the gravity direction. Further model improvements are also discussed for future work.

36 MATERIALS SCIENCE↗

Synthesis of functional polyurethanes and polyesters from biomass-derived monomers

A method of making polyesters and polyurethanes from biomass-derived polyols. The polyol is biomass-derived and has the structure: wherein dashed bonds are single or double bonds and R is selected from the group consisting of —OH and ═O. Polyurethanes are made by reacting the polyol with a diisocyanate. Polyesters are made by reacting the polyol with a dicarboxylic acid.

Chang, Hochan↗

Synthesizing, Compounding, and Characterizing a Heat Labile Polyurethane Foam

ABSTRACT A need exists for a packaging foam material that can be converted from solid to gaseous degradation products at reasonably low energy levels or temperatures, such as 100O C. This paper will primarily discuss the approaches currently being used to synthesize and characterize such a material. These approaches include the incorporation of novel polyols such as azo containing diols, polycarbonate diols, and polypropylene carbonate polyols into polyurethane foams. Characterization methods include NMR, FTIR, TGA, finite element analysis, impact strength, and others. This project will be funded for a duration of three years. Year 1 focused on developing the proposed test methods and producing an initial rigid polyurethane foam. Year 2 focuses on refining the materials and test methods. If appropriate, design of experiment (doe) techniques will be used to optimize components, component levels, density and other variables to attain required final material properties (TGA weight loss, impact strength, etc.). Year 3 focuses on scaling up to larger engineering quantities. The application for this material is in load securement for transportation of low level radioactive waste materials within the US Department of Energy (DOE) complex. Foam in place process equipment and operators will be shielded using this novel method over current practice. Current practice can involve time consuming methods of load securement in low level radiation environments. This new technique would eliminate exposure time securing the load and greatly improve the As Low As Reasonably Attainable (ALARA) conditions. The objective is to progress to higher Technical Readiness Levels (TRL) and larger pilot scale quantities. This paper discusses methodologies and presents current results to date.

Kranjc, Mark D.↗

Circular Reprocessing of Thermoset Polyurethane Foams

Thermoset polyurethane (PU) foams are widely used in industrial applications, but they cannot be recycled by conventional melt reprocessing because of their cross-linked structures. The introduction of carbamate exchange catalysts converts thermoset PU into covalent adaptable networks (CANs), which are amenable to reprocessing at elevated temperatures. However, this approach has produced solid PU films, which have fewer uses and lower commercial demand. In this work, simultaneous reprocessing and refoaming of thermoset PU foams is demonstrated by leveraging the melt-processability of PU CANs and allowing cell growth by gas generation in a twin-screw extruder. The optimal operating temperature of the refoaming process is determined through chemical, thermal, and structural analysis of PU foam extrudates. The foam-to-foam extrusion process produces controllable, continuous, and uniform foam structures, as characterized by cell diameter and cell number density. Low-density PU foams are obtained through a process simulating injection molding. The compression properties of reprocessed PU foam are compared with as-synthesized PU foam to demonstrate efficacy of the refoaming processes. These results demonstrate that PU foams can be prepared through recycling while maintaining microstructural and chemical integrity. In the future, this strategy may be applied to thermoset PU foams of various chemical compositions and shows promise for scalability.

36 MATERIALS SCIENCE↗

Chapter 6: TEA and LCA of Bio-Based Polyurethanes

For bio-based polyurethane (PU) to replace its conventional petroleum-based counterpart, it must be cost-competitive while providing a positive environmental benefit. Techno-economic analysis (TEA) and life cycle assessment (LCA) provide tools to quantify the economic and environmental viability of bio-based PU and to identify key drivers. Here we describe TEA and LCA methodologies for assessing bio-based PU, including an example case study for producing a flexible PU foam. This process has the potential to be cost-competitive with traditional PU based on a published study using a linseed oil proxy feedstock. Bio-based PU also demonstrates environmental advantages in some categories considered but faces challenges in others compared to petroleum-based PU. Further TEA and LCA beyond the case study may enable assessment for alternative product and process variations that are possible for bio-based PU.

bio-based polyurethane↗

Improved Surface wettability of polyurethane films by Ultraviolet Ozone treatment

The wettability of polyurethane (PU) was altered using ultraviolet ozone (UVO) treatment. The effect of UVO treatment on PU surface chemistry was investigated with various experiments. The direct measurement of sessile drops was employed to quantify the static contact angle of different wetting liquids on homogeneous PU films with various UVO treatment times. The contact angle of DI water droplets was decreased to 17.2{sup o} from 70.04{sup o} after 5 min UVO treatment. The surface free energy of PU films was 51.46 mN m{sup -1} before treatment and was increased to 71.5 mN m{sup -1} after being fully treated. X-ray photoelectron spectroscopy (XPS) analysis shows a significant amount of polar functional species (C-O and C-O bonding) were formed on the PU surface by UVO treatment. atomic force microscopy (AFM) characterization shows the PU surface morphology was different before and after UVO treatment. The effect of water washing on UVO treated surface was also investigated. An aging effect study indicates the UVO modification can sustain the improved wettability with limited hydrophobic recovery, where the DI water contact angle remains constant at around 22{sup o} after the UVO treatment.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Silicone membranes to inhibit water uptake into thermoset polyurethane shape-memory polymer conductive composites

Electroactive shape memory polymer (SMP) composites capable of shape actuation via resistive heating are of interest for various biomedical applications. However, water uptake into SMPs will produce a depression of the glass transition temperature (T g ) resulting in shape recovery in vivo. While water actuated shape recovery may be useful, it is foreseen to be undesirable during early periods of surgical placement into the body. Silicone membranes have been previously reported to prevent release of conductive filler from an electroactive polymer composite in vivo. In this paper, a silicone membrane was used to inhibit water uptake into a thermoset SMP composite containing conductive filler. Thermoset polyurethane SMPs were loaded with either 5 wt % carbon black or 5 wt % carbon nanotubes, and subsequently coated with either an Al 2 O 3 - or silica-filled silicone membrane. It was observed that the silicone membranes, particularly the silica-filled membrane, reduced the rate of water absorption (37°C) and subsequent T g depression versus uncoated composites. Finally, in turn, this led to a reduction in the rate of recovery of the permanent shape when exposed to water at 37°C.

36 MATERIALS SCIENCE↗

Renewable low viscosity polyester-polyols for biodegradable thermoplastic polyurethanes

In the transition to renewably sourced, biodegradable polymers, the preparation of low viscosity polyester-polyols has posed a challenge for renewable polyurethane (PU) development. Low viscosity polyols not only reduce the requirement for high process temperatures but also decrease manufacturing time. In our efforts to incorporate increasing ratios of bio-based monomers into renewable PUs, we mixed diacids such as even carbon sebacic acid and odd carbon azelaic acid along with a renewable diol. This provided library of 2000 g/mol molecular weight polyester-polyols, and structures were established by 1 H and 13 C NMR analysis. The prepared polyester-polyols offered lower viscosity and enable lower fabrication temperatures to make TPUs, and their structure and material metrics were evaluated. The formation of TPUs is ascertained from FTIR and NMR analysis. The final TPUs displayed good physical and mechanical properties. Further, these TPUs exhibited T g in the range of -56.5 to -39.7°C, corresponding to TPU soft block structure, and T m between 98.3 and 105.1°C originating from the hard segment. Prepared TPUs exhibit excellent biodegradation under compost environmental conditions. These TPUs showed up to 57% decrease in molecular weight by GPC analysis after 9 weeks of biodegradation, and respirometer analysis displayed up to 97% biodegradation over 120 days.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Selectively Depolymerizable Polyurethanes from Unsaturated Polyols Cleavable by Olefin Metathesis

This communication describes a novel series of linear and crosslinked polyurethanes (PUs) and their selective depolymerization under mild conditions. Two unique polyols are synthesized bearing unsaturated units in a configuration designed to favor ring-closing metathesis (RCM) to five- and six-membered cycloalkenes. These polyols are co-polymerized with toluene diisocyanate to generate linear PUs and trifunctional hexamethylene- and diphenylmethane-based isocyanates to generate crosslinked PUs. The polyol design is such that the RCM reaction cleaves the backbone of the polymer chain. Upon exposure to dilute solutions of Grubbs’ catalyst under ambient conditions, the PUs are rapidly depolymerized to low molecular weight, soluble products bearing vinyl and cycloalkene functionalities. These functionalities enable further re-polymerization by traditional strategies for polymerization of double bonds. We anticipate that this general approach can be expanded to develop a range of chemically recyclable condensation polymers that are readily depolymerized by orthogonal metathesis chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Quantifying the cooperative evolution of microphase segregation and nanostructural order in annealed polyurethanes of MDI-BDO-PTHF

Here, we quantify the relationship between microphase segregation and local structure development in thermoplastic polyurethanes. Samples were prepared with varying ratios of 4,40 -methylene diphenyl diisocyanate (MDI) and 1,4-butanediol (BDO) to polytetrahydrofuran (PTHF) and annealed at temperatures T a between RT–140 °C for 20 h each. Distinct populations of smaller and larger ordered domains are distinguished by pair distribution func tion analysis. The intermediate-range order of nanoscale hard domains in the paracrystalline state (form I) is directly extracted and characterized. The results suggest that form I of the MDI-BDO:PTHF system presents a conformational and packing order similar to the form III structure, typically obtained from stretching/annealing, but with limited spatial coherence of 3–7 nm. Heating above T g of the hard segments is necessary to achieve a substantial structural response from the annealing treatment. Increasing T a promotes purification of the soft phase via microphase segregation, coalescence of the hard blocks, and growth of paracrystalline phase, while a minority fraction of longer-range ordered domains left over from production remains relatively constant. We observe a composition-dependent decrease in the average nearest-neighbor dis tance that can be correlated with the greater number of C C, C N, and C O bonds with increased hard segment content. A non-linear deviation in the trend is observed to correlate with sample densification. The mechanical and thermal behavior of the samples is intimately tied to the segregation state.

processing-structure-properties↗

Functional group effect of chemically modified microcrystalline methyl cellulose on thermoplastic polyurethane composites

Microcrystalline cellulose (MCC) is a promising bio-based filler for lightweight yet mechanically high-performance eco-polymer composites because of its low density and high biocompatibility. However, intermolecular hydrogen bonding among MCC is stronger than the polymer–filler interactions, which deteriorate the mechanical properties of the composites. Herein, we investigated the effects of functional groups on the mechanical properties of composites by scrutinizing chemically modified microcrystalline methyl cellulose (m-MMC) with three different substitution levels of hydroxyl group to hydroxypropyl (HP) group: no-, low-, and high-level substitution (HP-0, HP-low, and HP-high). The degree of HP substitution of m-MMC was quantitatively measured by CP/MAS NMR analysis. The relatively bulky HP groups interrupted the filler–filler intermolecular interactions and reduced the crystallinity and density of m-MMC, as evident from X-ray diffractometer and pycnometer data, respectively. For scalable production of the composites, the m-MMC were compounded with thermoplastic polyurethane (TPU) by a twin-screw extruder at concentrations between 0.5 and 10 wt%. Despite its low filler concentration, the toughness of m-MMC/TPU composites was remarkably enhanced, up to 28% (229.2 to 294.4 MJ/m 3 ) at 0.5 wt% loading of HP-low, owing to the enhanced polymer–filler interactions. In conclusion, the fundamental understanding on structure–property relationships will provide insights for designing of mechanically robust yet eco-friendly polymer composites.

composites↗

Validation of heat transfer, thermal decomposition, and container pressurization of polyurethane foam using mean value and Latin hypercube sampling approaches

In this study, polymer foam encapsulants provide mechanical, electrical, and thermal isolation in engineered systems. It can be advantageous to surround objects of interest, such as electronics, with foams in a hermetically sealed container in order to protect them from hostile environments or from accidents such as fire. In fire environments, gas pressure from thermal decomposition of foams can cause mechanical failure of sealed systems. In this work, a detailed uncertainty quantification study of polymeric methylene diisocyanate (PMDI)-polyether-polyol based polyurethane foam is presented and compared to experimental results to assess the validity of a 3-D finite element model of the heat transfer and degradation processes. In this series of experiments, 320 kg/m 3 PMDI foam in a 0.2 L sealed steel container is heated to 1,073 K at a rate of 150 K/min. The experiment ends when the can breaches due to the buildup of pressure. The temperature at key location is monitored as well as the internal pressure of the can. Both experimental uncertainty and computational uncertainty are examined and compared. The mean value method (MV) and Latin hypercube sampling (LHS) approach are used to propagate the uncertainty through the model. The results of the both the MV method and the LHS approach show that while the model generally can predict the temperature at given locations in the system, it is less successful at predicting the pressure response. Also, these two approaches for propagating uncertainty agree with each other, the importance of each input parameter on the simulation results is also investigated, showing that for the temperature response the conductivity of the steel container and the effective conductivity of the foam, are the most important parameters. For the pressure response, the activation energy, effective conductivity, and specific heat are most important. The comparison to experiments and the identification of the drivers of uncertainty allow for targeted development of the computational model and for definition of the experiments necessary to improve accuracy.

42 ENGINEERING↗

Synthesis of Biodegradable and Blood-Compatible Polyurethane Based on Poly(vinylpyrrolidone)

Three kinds of degradable and blood-compatible polyurethane (PU) were synthesized by coupling hydroxyl-terminated poly(vinylpyrrolidone) (PVP) with diisocyanate-terminated PU. The chemical structure and molecular weight of the synthesized copolymer were systematically characterized by nuclear magnetic resonance spectrum ({sup 1}HNMR), Fourier transform infrared spectroscopy (FTIR) and gel permeation chromatography (GPC). The hydrophilicity and water absorption of the synthesized PU was increased by introducing PVP segment. To evaluate the hemocompatibility and degradability of the modified PU films, the extent of platelet adsorption, plasma recalcification time, hemolysis and degradation were measured. All results indicated that the blood compatibility and degradability of the PU films were improved significantly after introduction PVP segment into PU.

36 MATERIALS SCIENCE↗