Search NASA⌕ Search

SEARCH · Search NASA

Results for “residual strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Measuring residual stress in Ti-6Al-4V with HR-EBSD, using reference patterns from annealed material

In this study, elastic strain and residual stress values in an engineering material were determined by high-resolution EBSD (HR-EBSD) using reference patterns from annealed, recrystallized material. Specifically, rolled Ti-6Al-4V sheet was analyzed using HR EBSD in both an as-annealed and a strained state, the latter established via a static two-point bend fixture. The commercial software CrossCourt4 (CC4) was used to evaluate the relative intragranular strain tensor components of the alpha grains mapped by HR-EBSD. The intragranular reference patterns identified in each grain by the software were then replaced with similarly-oriented patterns from scans of the as-annealed, recrystallized material. The CC4 analysis was then repeated to provide calibrated strain and residual stress values. Elastic strains on the order of 10–3 were detected, with corresponding residual stress values on the order of 1 GPa. Subsequent analyses using high energy synchrotron x-ray diffraction showed good correlation with the elastic strains measured by HR-EBSD using the annealed reference patterns. Additionally, the maximum macroscopic stress analytically predicted for two-point bending was in agreement with the residual stress observed. Good repeatability of the methodology and insight into the state of individual grains were also observed. The findings provide encouraging evidence that accurate intragranular and long-range residual stress measurements of engineering significance can be made with HR-EBSD using a physical reference pattern library.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Crystallographic orientation and spatially resolved damage in a dispersion-hardened Al alloy

The in-situ neutron diffraction technique, in combination with both the full-field crystal elasto-viscoplastic finite element model and microstructural characterization, was used to study the deformation-induced damage anisotropy in a commercial Al alloy, subjected to uniaxial tensile and cyclic loading. The simulations capture well the crystallographic-orientation-dependent lattice strain behavior. The hard grains, e.g. those orientated with the <111> and <422> orientations parallel with the uniaxial loading direction (LD), feature large Taylor factors and seem more prone to form damage-related band structures. Their effective elastic moduli decrease with the accumulation of damage, which are different from the soft grains orientated with the <200> orientation along the LD. Correlation between the distribution of voids and that of the residual lattice strain developed after failure may exist. The maximum tensile type residual lattice strain observed after failure may be resulted from the band structure formed in the hardest <111> grains. It was revealed that the band structure triggered by the hard particles could be one of sources of damage. In addition, while the specimen was obviously damaged, a fast stress relief was evidenced after unloading from the tension, especially at the beginning of unloading. Our present investigations provide a novel method for exploring the damage mechanisms of polycrystalline materials during plastic deformation.

36 MATERIALS SCIENCE↗
NASA NTRS1986

Thermomechanical design criteria for ceramic-coated surfaces

Some early history of ceramic applications is presented. Finite element modeling of components to determine service and fabrication loads found inelastic behavior and residual stresses to be significant to component life. Inelastic behavior mitigates peak strains but enhances residual strains. Results of furnace, Mach 0.3 burner, and engine tests are discussed and categorized into design criteria (loading, geometry, fabrication, materials, analysis, and testing). These design rules and finite element analyses are brought to bear on two test cases: turboshaft engine seals, and rocket thrust chambers.

Mullen, R. L.↗
DOE OSTI2022

Residual stress and microstructure in IN718-René41 graded superalloy fabricated by laser blown directed energy deposition

Additively printed Ni-based superalloy with a compositionally graded transition from IN718 to René41 was fabricated by laser blown-powder directed energy deposition (DED/LB-M), with the goals of meeting location-specific temperature capability and reducing component cost for hot gas path turbine components. Residual stress distribution in thin wall specimens with three sets of DED build parameters in the as-built and stress-relieved states was measured by neutron diffraction. For calculating residual stress, the calculated d0 method was found to be more appropriate as stress-free reference than using the lattice spacing measured from the stress-relief heat treated specimens. Longer dwell time (lower interpass temperature), higher energy input, smaller layer thickness resulted in a higher magnitude of tensile residual stresses at edges and compressive residual stresses at center of the specimens. The residual stress results did not show a strong dependence on graded compositions, indicating that the residual stress build-up was more geometry and process dependent. Non-destructive neutron imaging based on the attenuation coefficient qualitatively visualized the compositional variation in the bulk and showed good agreement with quantitative Electron Probe Micro-Analysis (EPMA) measurement. Grain structure, texture, and residual plastic strain along the build direction were characterized by Electron Backscatter Diffraction (EBSD). Long columnar grains with (001) preferred grain orientation were dominant along the build direction. Compositional change did not show an obvious effect on the epitaxial growth of dendrites and the continuation of the columnar grains. Residual plastic strain was relatively low in the as-built specimens.

36 MATERIALS SCIENCE↗
NASA NTRS1993

A study of subsurface crack initiation produced by rolling contact fatigue

Results of subsurface crack initiation studies produced by pure rolling contact fatigue in 7075-T6 aluminum alloy are presented in this article. Microstructural changes and subsequent crack initiation below the contacting surface in cylindrical test specimens subjected to repeated rolling contact are illustrated. The rolling conditions are simulated in a three-dimensional elastic-plastic finite element model in order to estimate the plastic strains and residual stresses in the test material. The numerically estimated distribution of plastic strains in the model correlate well with the extent of microstructural changes observed in the test specimen. Results also indicate that a combination of plastic strains and low values of residual stresses is conducive to subsurface crack initiation and growth.

Kumar, Arun M.↗
NASA NTRS1980

Plasma sprayed ceramic thermal barrier coatings for turbine vane platforms

The paper describes the results to date of an investigation of advanced plasma sprayed ceramic coatings to demonstrate cooling concepts applicable for turbine vane platforms. It is noted that the increased resistance of plasma sprayed ceramic coatings to cyclic thermal exposure can be achieved by increasing the strain tolerance of the ceramic and by controlling harmful residual stresses. Strain tolerance can be increased by controlling internal structure to minimize harmful flaws and to add favorable discontinuities.

Ruckle, D. L.↗
NASA NTRS1990

Some optical and electron microscope comparative studies of excimer laser-assisted and nonassisted molecular-beam epitaxically grown thin GaAs films on Si

The quality of GaAs thin films grown via MBE under pulsed excimer laser irradiation on Si substrates is examined in both laser-irradiated and nonirradiated areas using Raman scattering, Rayleigh scattering, and by photoluminescence (PL), as a function of temperature, and by TEM. The temperature dependence of the PL and Raman peak positions indicates the presence of compressive stress in the thin GaAs films in both laser-irradiated and nonirradiated areas. This indicates incomplete homogeneous strain relaxation by dislocations at the growth temperature. The residual compressive strain at the growth temperature is large enough such that even with the introduction of tensile strain arising from the difference in thermal expansion coefficients of GaAs and Si, a compressive strain is still present at room temperature for these thin GaAs/Si films.

Lao, Pudong↗
NASA NTRS1976

Effect of laminate construction on residual stresses in composites

The effects of ply stacking sequence and ply orientation on the magnitude of lamination residual stresses in graphite/polyimide angle-ply laminates was studied. Embedded strain gage techniques were used to measure thermal strains in laminates of different layup, and residual strains were determined by comparing thermal strains in the angle-ply laminates with those of a unidirectional laminate. The ply stacking sequence did not have an effect on the magnitude of residual strains.

Daniel, I. M.↗
DOE OSTI2022

Strain Gauge Diagnostic Development for use in Vessel Health Monitoring for Hydro-shots

Six-foot vessels are a crucial component to protecting high fidelity equipment at DARHT. Analysis shows these vessels have a limited life span (~10 shots) due to fatigue, ratcheting, and damage accumulation. Vessel health monitoring and diagnostics can help inform decision on a vessel’s fitness for service. Strain gauges are an easy and effective sensor for use in vessel health monitoring. In early March, J-2 executed a qualification shot, uniform blast loading with minimal fragments, with bi-axial strain gauges fielded at four locations around vessel. Several damage features were extracted from the data, and frequency content helps to validate computer modelling of the vessel response. Permanent plastic strain at each location was significant with location one having the most strain at the end state, with 230 micro-strain. However, residual pressure in the vessel could be a major factor in this strain. PEEQ is a measure of total plastic equivalent strain accumulation. The equivalent strain at location one exceeded the plastic strain limit four times and accumulated the most PEEQ with 2036 micro-strain. As expected, this qualification shot did contribute to damage in the vessel, and should be considered in its fitness for service, but not critical enough to pull it from service. Frequency content also gave valuable information on the modal response of the vessel and contributes to the understanding of how the vessel responds to the initial blast load with an expected lower frequency membrane/breathing mode and transitioning to higher frequency bending modes in the vessel wall.

42 ENGINEERING↗
DOE OSTI2023

Ion-beam radiation-induced Eshelby transformations: The mean and variance in hydrostatic and shear residual stresses

Ion beam plays a pivotal role in ion implantations and the fabrication of nanostructures. However, there lacks a quantitative model to describe the residual stresses associated with the ion-beam radiation. Radiation-induced residual stress/transformation strain have been mostly recognized in the hydrostatic sub strain space. Here, in this study, we use molecular dynamics (MD) simulations to show that the response of a material to irradiation is generally anisotropic that depends on the ion-beam direction, and should be described using tensorial quantities. We demonstrate that accelerator-based ion beam irradiation, combined with the intrinsic lattice anisotropy and externally induced anisotropy (such as anisotropic mechanical loadings), causes radiation-actuated shear transformation strains in addition to hydrostatic expansion. We map out these complex correlations for several materials. Radiation-induced defects are shown to be responsible for residual shear stresses in the manner of Eshelby inclusion transformation. We propose such tensorial response model should be considered for accurate nanoscale fabrication using ion-beam irradiation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Development of High-Temperature Bonding Techniques to Enable High-Temperature Static or Dynamic Strain Measurements

Current light-water nuclear reactors rely on a variety of different sensors and sensor applications to meet their structural health monitoring needs throughout the entirety of the reactor primary, secondary, and containment systems. Optical fiber–based sensor technologies could provide solutions to reduce the sensor system footprint while enhancing the measurement fidelity and spatial resolution by leveraging distributed monitoring techniques. Moreover, advanced reactors may require optical fiber–based sensors for structural health monitoring because their operating temperatures will exceed the limits of conventional transducers used to acquire dynamic strain or acoustic data in nuclear power plants. Therefore, this report describes experiments targeting the development of high-temperature bonding techniques that would allow for potentially long lengths of fibers to be bonded to metallic reactor components in advanced reactor systems. The high temperatures experienced within target application, next-generation nuclear reactors, necessitate a high-temperature resistant bond to limit the amount of tension on the fiber at the target application temperature. The primary bonding method investigated in this work is brazing; hot-rolling has also been investigated to a lesser extent. Both techniques are well-suited to bonding optical fibers to large reactor components such as primary coolant piping, pressure vessels, or heat exchangers. Optical frequency domain reflectometry was used to monitor the strain in metal-coated optical fibers before, during, and after the high-temperature bonding process. On select optical fibers that were successfully bonded, additional thermal cycling was performed to assess the extent to which the fiber remained bonded based on the expected thermal expansion of the test specimen material. The results of the various experiments yielded the following general conclusions: (1) brazing is a viable technique for bonding and allows significant compressive strain to be applied to the fiber at room temperature; (2) hot-rolling is a viable technique as well, which has been more optimized than the brazing technique for bonding, but less residual compressive strain has been observed with this technique; and (3) both techniques will need further development and optimization to demonstrate bonding of a long length of fiber that can provably operate at relevant temperatures for an advanced nuclear reactor application.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1979

Wave propagation in transversely impacted composite laminates

An experimental study was conducted to determine the wave-propagation characteristics, transient strains and residual properties of unidirectional and angle-ply boron/epoxy and graphite/epoxy laminates impacted with silicon-rubber projectiles at velocities up to 250 m/sec. Results include the following: (1) the predominant wave is the flexural wave propagating at different velocities in different directions; (2) peak strains and strain rates in the transverse to the (outer) fiber direction are much higher than those in the direction of the fibers; (3) strain rates up to 640/sec were measured; and (4) unidirectional laminates under impact showed appreciable modulus and strength degradation in the direction transverse to fibers.

Daniel, I. M.↗
NASA NTRS2002

Residual Stress Reversal in Highly Strained Shot Peened Structural Elements

The purpose of this research was to further the understanding of a crack initiation problem in a highly strained pressure containment housing. Finite Element Analysis methods were used to model the behavior of shot peened materials undergoing plastic deformation. Analytical results are in agreement with laboratory tensile tests that simulated the actual housing load conditions. These results further validate the original investigation finding that the shot peened residual stress had reversed, changing from compressive to tensile, and demonstrate that analytical finite element methods can be used to predict this behavior.

Mitchell, William S.↗
DOE OSTI2022

Damage Tolerance Assessment of Laser Clad Repairs of Coarse Grain Ti-6Al-4V

Background: Laser cladding offers a promising approach to repairing aviation components, with the ability to restore the geometric shape and the static and fatigue strength. Objective: The damage tolerance of a coarse grain Ti-6Al-4 V material is assessed via three sets of samples: (i) baseline, (ii) laser clad repaired, and (iii) laser cladding followed by heat treatment. Method: The specimens were subjected to fatigue loading using a marker band technique, in which cracks initiated from pre-defined laser slots and the small crack growth rates were measured by quantitative fractography. Additional characterization was performed on these samples, including hardness measurements, microstructure analysis, and multimodal residual stress analyses. Results: The region of the specimen undergoing laser cladding exhibited higher hardness values and a compressive residual stress, based on the slitting method. The samples subjected to heat treatment after cladding displayed negligible differences in grain size and minimal residual stress relaxation. Conclusions: The results demonstrated significant variability, with data demonstrating that cracks in the laser clad region (exhibiting the largest compressive residual stress) grew faster than cracks in the substrate region of the sample or in the baseline cases. Finally, these counterintuitive results are rationalized with additional analyses from synchrotron-based energy dispersive X-ray diffraction and high energy X-ray diffraction, demonstrating significant spatial variability in the residual elastic strains in the millimeter-sized prior β grains within the material.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Wave propagation in fiber composite laminates, part 2

An experimental investigation was conducted to determine the wave propagation characteristics, transient strains and residual properties in unidirectional and angle-ply boron/epoxy and graphite/epoxy laminates impacted with silicone rubber projectiles at velocities up to 250 MS-1. The predominant wave is flexural, propagating at different velocities in different directions. In general, measured wave velocities were higher than theoretically predicted values. The amplitude of the in-plane wave is less than ten percent of that of the flexural wave. Peak strains and strain rates in the transverse to the (outer) fiber direction are much higher than those in the direction of the fibers. The dynamics of impact were also studied with high speed photography.

Daniel, I. M.↗
NASA NTRS1980

Thermal expansion of composites using Moire interferometry

An experimental technique for precise measurement of the thermal response of fiber-reinforced composite materials uses moire interferometry with fringe multiplication which yield a sensitivity of 833 nm (32.8 mu in.) per fringe. Results from the technique are compared with those obtained from electrical resistance strain gages, and also those predicted from classical lamination theory. Temperature dependent coefficients of thermal expansion for composite materials subjected to thermal cycling in the temperature range of 297 K (75 F) to 422 K (300 F) were determined for four laminate configurations (0, 90, 0/ + or - 45/90 sub s and 0/90/ + or - 45 sub s) of T300/5208 graphite epoxy, and ranged from -0.107 mu epsilon K/1 (-0.059 mu epsilon deg F/-) for the 0 laminate to 32.18 mu epsilon K/1 (17.88 mu epsilon F/1) for the 90 laminate. Moisture was found to greatly influence the thermal response of a quasi-isotropic laminate, resulting in hysteresis and residual compressive strain as the moisture content was reduced. Comparisons between moire and strain gage measurements were inconclusive with both techniques giving consistent but systematically different results. Differences of as much as 29% were observed.

Bowles, D. E.↗
DOE OSTI2020

Mechanisms of paint bake response in resistance spot-welded first and third generation AHSS

Implementation of 3rd generation advanced high strength steels (3GAHSS) in automotive structures requires careful consideration of joining process implications. Due to the presence of increased carbon equivalent in 3GAHSS such as 980 HF relative to commonly-applied 1st generation AHSS such as 980 DP, the resultant properties of the weld nugget and heat affected zones in resistance spot welded must be engineered to provide consistent and acceptable performance, specifically in cross-tension loading mode. Although the as-welded cross-tension strength (CTS) of 980 HF is less than 980 DP, there is a significant improvement of the CTS after paint baking in 980 HF welds. 980 DP steel welds do not exhibit such marked improvement upon baking. The mechanism of the strong and beneficial effect of paint baking on 980 HF in comparison to 980 DP is discussed in light of its effect on residual stress distributions and microstructures. Although residual stress (strain) reduction is observed via synchrotron x-ray diffraction for all tested steels, this effect is demonstrated as secondary to the performance restoration of the weld joint in cross tension. High-resolution electron channeling contrast imaging (ECCI) micrographs reveal that paint baking affects a more beneficial degree of martensite tempering in 980 HF as compared to 980 DP. The martensite tempering is also evidenced by both a reduction in nano-hardness of critical microstructural features and re-emergence of ductile fracture behavior following the paint baking process. The tempering of martensite is concluded to be the dominant mechanism in improving cross tension strength of 3GAHSS welds following paint baking.

36 MATERIALS SCIENCE↗
NASA NTRS1985

Residual thermal and moisture influences on the strain energy release rate analysis of edge delamination

A laminated plate theory analysis is developed to calculate the strain energy release rate associated with edge delamination growth in a composite laminate. The analysis includes the contribution of residual thermal and moisture stresses to the strain energy released. The strain energy release rate, G, increased when residual thermal effects were combined with applied mechanical strains, but then decreased when increasing moisture content was included. A quasi-three-dimensional finite element analysis indicated identical trends and demonstrated these same trends for the individual strain energy release rate components, G sub I and G sub II, associated with interlaminar tension and shear. An experimental study indicated that for T300/5208 graphite-epoxy composites, the inclusion of residual thermal and moisture stresses did not significantly alter the calculation of interlaminar fracture toughness from strain energy release rate analysis of edge delamination data taken at room temperature, ambient conditions.

Obrien, T. K.↗