Search NASA⌕ Search

SEARCH · Search NASA

Results for “silicides”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1969

Protective coatings for chromium alloys.

Ductile metal clads and coatings of silicides, aluminides and noble metals to protect Cr alloys against nitrogen embrittlement and air oxidation

Grisaffe, S. J.↗
NASA NTRS1971

Protective coatings for columbium applied in the field.

The various aspects of field repair of columbium alloy panels with protective coatings designed as part of the Space Shuttle thermal protection system are examined. The field repair of the coatings is accomplished by employing ceramic cement repairs, and reapplying the fused slurry silicide coating. Techniques are described which improve the practicality of these repairs by employing torch heating. The repair coating quality is demonstrated by testing which simulates flight temperature, pressure, stress and acoustic vibration conditions as a function of time. Conclusions on the present status of field repair coatings are presented and recommendations are given for appropriate future activities relative to the use on an operational Space Shuttle system.

Carter, J.↗
NASA NTRS1973

Measured catalycities of various candidate space shuttle thermal protection system coatings at low temperatures

Atom recombination catalytic rates for surface coatings of various candidate thermal protection system materials for the space shuttle vehicle were obtained from measurements in arc jet, air flow. The coatings, chrome oxides, siliconized carbon/carbon, hafnium/tantalum carbide on carbon/carbon, and niobium silicide, were bonded to the sensitive surface of transient slug calorimeters that measured the heat transfer rates to the coatings. The catalytic rates were inferred from these heat transfer rates Surface temperatures of the calorimeters varied from approximately 300 to 410 K.

Scott, C. D.↗
NASA NTRS1972

Field repair of coated columbium Thermal Protection System (TPS)

The requirements for field repair of coated columbian panels were studied, and the probable cause of damage were identified. The following types of repair methods were developed, and are ready for use on an operational system: replacement of fused slurrey silicide coating by a short processing cycle using a focused radiant spot heater; repair of the coating by a glassy matrix ceramic composition which is painted or sprayed over the defective area; and repair of the protective coating by plasma spraying molybdenum disilicide over the damaged area employing portable equipment.

Culp, J. D.↗
NASA NTRS1973

Development of techniques and associated instrumentation for high temperature emissivity measurements

Studies were made to develop a test apparatus for the measurement of total emittance of materials under repeated exposure to simulated earth entry conditions. As no existing test facility met the emittance measurement and entry simulation goals, a new apparatus was designed, fabricated and checked out. This apparatus has the capability of performing total and spectral emittance measurements during cyclic temperature and pressure exposure under sonic and supersonic flow conditions. Emittance measurements were performed on a series of oxidized superalloys, silicide coated columbium alloys and ceramic coatings.

Cunnington, G. R.↗
NASA NTRS1972

Space Shuttle bipropellant RCS engine.

The requirements of the Space Shuttle bipropellant reaction control system engine technology contract and the scheduled contract effort are presented herein. The requirements included an engine concept scalable from 400 to 1100 lbf, with a 100 mission life employing N2O4/MMH propellants. Emphasis is placed on reusability and minimum post-flight servicing. The engine components are reviewed and their selection is supported by tradeoff analyses, thrust chamber firing test data, materials test data, and metallurgical evaluations. The materials test data indicate that the proposed silicide coated columbium chamber and uncoated columbium injector have the potential of meeting the mission life requirements. The engine valve trade studies resulted in the selection of a torque motor operated bipropellant valve configuration. Fuel vortex film cooling of the insulated chamber is described together with the fuel vortex film cooling scaling parameter and its verification by test data to a thrust level of 5500 lbf.

Sanscrainte, W.↗
NASA NTRS1973

Evaluation of coated columbium alloy heat shields for space shuttle thermal protection system application. Volume 2, phase 2: Subsize heat shield and small size TPS evaluation

Initially a trade study was conducted of seven heat shield configurations. These were evaluated for structural reliability, fabricability, weight, inspectability, and refurbishability. Two concepts, a tee-stiffened and an open corrugation, were selected as offering the most potential for system success. Fourteen subsize heat shields of a full scale section were fabricated from C-129Y and Cb-752 and silicide coated with R-512E. These subsize panels were subjected to a simulated flight profile representing temperature, local surface pressures, and applied pressure differential loads. All corrugated panels of both alloys sustained 100 cycles without structural or coating failure. All Cb-752/R-512E panels performed well with one panel being successfully repaired after 66 cycles and completing 100 cycles. As a result of this evaluating the Cb-752/R-512E system was selected for hardware application during the subsequent phases. In addition, the tee-stiffened configuration was selected for further development and application in Phase III. This selection was based on an overall assessment of relative weight, cost, and structural performance of the tee-stiffened and open corrugation TPS.

Black, W. E.↗
NASA NTRS1973

Environmental protection to 922K (1200 F) for titanium alloys

Evaluations are presented of potential coating systems for protection of titanium alloys from hot-salt stress-corrosion up to temperatures of 755 K (900 F) and from oxidation embrittlement up to temperature of 922 K (1200 F). Diffusion type coatings containing Si, Al, Cr, Ni or Fe as single coating elements or in various combinations were evaluated for oxidation protection, hot-salt stress-corrosion (HSSC) resistance, effects on tensile properties, fatigue properties, erosion resistance and ballistic impact resistance on an alpha and beta phase titanium alloy (Ti-6Al-2Sn-4Zr-2Mo). All of the coatings investigated demonstrated excellent oxidation protectiveness, but none of the coatings provided protection from hot-salt stress-corrosion. Experimental results indicated that both the aluminide and silicide types of coatings actually decreased the HSSC resistance of the substrate alloy. The types of coatings which have typically been used for oxidation protection of refractory metals and nickel base superalloys are not suitable for titanium alloys because they increase the susceptibility to hot-salt stress-corrosion, and that entirely new coating concepts must be developed for titanium alloy protection in advanced turbine engines.

Groves, M. T.↗
NASA NTRS1974

Performance of coated columbium and tantalum alloys in plasma arc reentry simulation tests

The evaluation of coated refractory metals screened in stagnation model plasma arc tests is reported. Columbium alloys FS-85, C-129Y, and Cb-752 coated with Si-20Cr-20Fe (R512E) were tested at 1390 C. Three silicide coatings on Ta-10W were tested at 1470 C. Half-hour cycles and a 6500 N/sqm stagnation pressure were used. The best R512E coated columbium alloy was FS-85 with first local coating breakdowns occurring in 12 to 50 cycles. At coating defects, low metal recession rates (0.005 mm/min) were generally observed on coated columbium alloys while high rates (0.15 mm/min) were observed on coated Ta-10W. Coated columbium suffered large emittance losses (to below 0.7) due to surface refractory metal pentoxide formation.

Levine, S. R.↗
NASA NTRS1973

Eddy-current measurements of thickness of high-temperature coatings

The eddy-current technique was applied to measuring the thickness of a fused silicide coating on a refractory alloy slab. Phase and magnitude of the test signal were measured at four places in 13 different samples, and thickness of coating was computed on the basis of each of these quantities. These results were then compared with those obtained by conventional metallographic methods. Phase-based measurements were most reliable, and the maximum error between the metallographically determined thickness and the thickness as determined by the least squares fit to the phase measurements was less than 0.01 mm (about 1%). Photomicrography of a typical sample shows that a large source of error resides in the fact that two regions - an outer rough region and an inner uniform region - of the coating layer exist rather than the single region upon which the calculations were based.

Dodd, C. V.↗
NASA NTRS1977

New process produces high-power Schottky diodes

Processing procedure using low-temperature platinum silicide, results in successful high-yield fabrication of large-area mesa-geometry Schottky diodes, with reverse breakdown voltages as high as 150 volts and leak currents less than 5 milliamps at 212 F.

Cordes, L. F.↗
NASA NTRS1978

Coatings for wear and lubrication

Recent advances in the tribological uses of rf-sputtered and ion plated films of solid film lubricants (laminar solids, soft metals, organic polymers) and wear resistant refractory compounds (carbides, nitrides, silicides) are reviewed. The sputtering and ion plating potentials and the corresponding coatings formed were evaluated relative to the friction coefficient, wear endurance life and mechanical properties. The tribological and mechanical properties for each kind of film are discussed in terms of film adherence, coherence, density, grain size, morphology, internal stresses, thickness, and substrate conditions such as temperature, topography, chemistry and dc-biasing. The ion plated metallic films in addition to improved tribological properties also have better mechanical properties such as tensile strength and fatigue life.

Spalvins, T.↗