Search NASA⌕ Search

SEARCH · Search NASA

Results for “Panel method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Benchmarking Gas Path Diagnostic Methods: A Public Approach

Recent technology reviews have identified the need for objective assessments of engine health management (EHM) technology. The need is two-fold: technology developers require relevant data and problems to design and validate new algorithms and techniques while engine system integrators and operators need practical tools to direct development and then evaluate the effectiveness of proposed solutions. This paper presents a publicly available gas path diagnostic benchmark problem that has been developed by the Propulsion and Power Systems Panel of The Technical Cooperation Program (TTCP) to help address these needs. The problem is coded in MATLAB (The MathWorks, Inc.) and coupled with a non-linear turbofan engine simulation to produce "snap-shot" measurements, with relevant noise levels, as if collected from a fleet of engines over their lifetime of use. Each engine within the fleet will experience unique operating and deterioration profiles, and may encounter randomly occurring relevant gas path faults including sensor, actuator and component faults. The challenge to the EHM community is to develop gas path diagnostic algorithms to reliably perform fault detection and isolation. An example solution to the benchmark problem is provided along with associated evaluation metrics. A plan is presented to disseminate this benchmark problem to the engine health management technical community and invite technology solutions.

Simon, Donald L.↗

Development and demonstration of manufacturing processes for fabricating graphite/PMR-15 polyimide structural elements

The processing requirements for graphite/PMR-15 polyimide composites developed to demonstrate the structural integrity of polyimide composite structural elements at temperatures up to 589K (600 F) are described. Major tasks included: quality assurance development; materials and process development; specification verification; flat panel fabrication; stiffened panel fabrication; honeycomb panel fabrication; chopped fiber moldings; and demonstration component fabrication. Materials, processing, and quality assurance documents were prepared from experimentally derived data. Structural elements consisting of flat panels, corrugated stiffeners, I-beams, hat stiffeners, honeycomb panels, and chopped fiber moldings were made and tested. Property data from 219K (-65 F) to 589K (600 F) were obtained. All elements were made in a production environment. The size of each element was sufficient to insure production capability and structural component applicability. Problems associated with adhesive bonding, laminate and structural element analysis, material variability, and test methods were addressed.

Sheppard, C. H.↗

A program for calculating load coefficient matrices utilizing the force summation method, L218 (LOADS). Volume 2: Supplemental system design and maintenance document

The LOADS computer program L218 which calculates dynamic load coefficient matrices utilizing the force summation method is described. The load equations are derived for a flight vehicle in straight and level flight and excited by gusts and/or control motions. In addition, sensor equations are calculated for use with an active control system. The load coefficient matrices are calculated for the following types of loads: (1) translational and rotational accelerations, velocities, and displacements; (2) panel aerodynamic forces; (3) net panel forces; and (4) shears, bending moments, and torsions.

Anderson, L. R.↗

Preliminary evaluation of large area bonding processes for repair of graphite/polyimide composites

It is pointed out that graphite/polyimide (Gr/PI) composites are potential candidates for primary and secondary structural components in the next generation of reusable space vehicles and supersonic aircraft which are to possess operational capabilities involving the temperature range from 400 to 600 F. In connection with the considered applications, it is necessary to establish economic and reliable methods for the repair of Gr/PI composite components which have been damaged. The present investigation is concerned with the results of research conducted to develop a bonding process applicable to the repair of large areas in Gr/PI composite structural components. Attention is given to five repair techniques for Gr/PI composite materials. The techniques were employed to fabricate large panels from which flexure and short-beam-shear specimens were machined.

Deaton, J. W.↗

Shear fatigue crack growth - A literature survey

Recent studies of shear crack growth are reviewed, emphasizing test methods and data analyses. The combined mode I and mode II elastic crack tip stress fields are considered. The development and design of the compact shear specimen are described, and the results of fatigue crack growth tests using compact shear specimens are reviewed. The fatigue crack growth tests are discussed and the results of inclined cracks in tensile panels, center cracks in plates under biaxial loading, cracked beam specimens with combined bending and shear loading, center-cracked panels and double edge-cracked plates under cyclic shear loading are examined and analyzed in detail.

Liu, H. W.↗

Buckling analysis of fully anisotropic plates containing cutouts and elastically restrained edges

An analysis is developed which combines the Ritz and collocation methods for the stability solution of an anisotropic plate with a cutout and elastically restrained edges. Results are presented which agree closely with experiment for isotropic and orthotropic materials. Results are also given for restrained anisotropic plates with circular holes loaded in compression and shear. Difference is noted in the critical buckling loads between displacement and stress loaded panels as hole size is increased. Clamping is also seen to affect the trends in buckling associated with hole size.

Jones, Kevin M.↗

Ice Accretion Calculations for a Commercial Transport Using the LEWICE3D, ICEGRID3D and CMARC Programs

Collection efficiency and ice accretion calculations were made for a commercial transport using the NASA Lewis LEWICE3D ice accretion code, the ICEGRID3D grid code and the CMARC panel code. All of the calculations were made on a Windows 95 based personal computer. The ice accretion calculations were made for the nose, wing, horizontal tail and vertical tail surfaces. Ice shapes typifying those of a 30 minute hold were generated. Collection efficiencies were also generated for the entire aircraft using the newly developed unstructured collection efficiency method. The calculations highlight the flexibility and cost effectiveness of the LEWICE3D, ICEGRID3D, CMARC combination.

Bidwell, Colin S.↗

Reducing Undue Conservatism in "Higher Frequency" Structural Design Loads in Aerospace Components

This study is intended to investigate the frequency dependency of significant strain due to vibratory loads in aerospace vehicle components. The notion that "higher frequency" dynamic loads applied as static loads is inherently conservative is perceived as widely accepted. This effort is focused on demonstrating that principle and attempting to evolve methods to capitalize on it to mitigate undue conservatism. It has been suggested that observations of higher frequency modes that resulted in very low corresponding strain did so due to those modes not being significant. Two avionics boxes, one with its first significant mode at 341 Hz and the other at 857 Hz, were attached to a flat panel installed on a curved orthogrid panel which was driven acoustically in tests performed at NASA/MSFC. Strain and acceleration were measured at select locations on each of the boxes. When possible, strain gage rosettes and accelerometers were installed on either side of a given structural member so that measured strain and acceleration data would directly correspond to one another. Ultimately, a frequency above which vibratory loads can be disregarded for purposes of static structural analyses and sizing of typical robust aerospace components is sought.

Knight, J. Brent↗

Integration of Fatigue R-Curve Effects into VCCT for Durability Predictions, Part 2: Buckled Composite Multi-Stringer Stiffened Panels

Composite structures with hat-stiffened panels have gained traction in modern aircraft because they help reduce weight, increase durability, and provide stability to airframe skins. For weight reduction, skins should be designed to operate in the post-buckling regime. This causes possible interlaminar and intralaminar failure. However, composite panels stiffened with multiple hat-stringers are subject to cyclic loading even in the post-buckling regime. Under the NASA Advanced Composites Project (ACP), composite panels with multiple hatstringers were subject to a cyclic loading sequence from a pre-buckling state to a post-buckling state. This effort aimed to predict interlaminar failure for cyclic compression loading with pre-existent impact-induced damage. This work uses the Abaqus FEA Virtual Crack Closure Technique (VCCT), capabilities enhanced through an empirical method to integrate fatigue R-curve effects (different from R-ratio) into the Paris Law via user-defined subroutine to simulate the fatigue response o

ACP↗

Impact of Thermoplastic Composites: Testing and Modeling

Thermoplastic Composites (TPCs) are being increasingly considered for aerospace applications given their faster manufacturing cycles and lower cost. The NASA High-Rate Composite Aircraft Manufacturing (HiCAM) project aims to evaluate and mature thermoplastic manufacturing technologies to achieve a 4X – 6X increase in the production rate of Next Generation Single Aisle (NGSA) commercial aircraft. Within the purview of the NASA HiCAM project, this work investigates the response of thermoplastic composites under High Energy Dynamic Impact (HEDI) conditions. HEDI tests were conducted on panels fabricated with a carbon fiber reinforced low melt semi-crystalline resin TC1225 LMPAEK T700G (T700/LMPAEK) material system. A blunt metal projectile was chosen as the impactor which impacted the T700/LMPAEK panels over a range of impact velocities imparted by a gas gun test setup. As expected, lower velocity impacts caused the projectile to rebound, whereas higher velocity impacts resulted in the projectile penetrating the test panels. For the test cases in which the projectile rebounded, the predominant damage modes recorded with Ultrasonic (UT) scans included interlaminar delaminations which exhibited a “rotating fan” like structure when viewed in the through-thickness direction. Additionally, the dynamic deflection of the center point of the back face of the test panels and the velocity of the projectile was also measured during the test. Finite element models were developed to model a test case in which the projectile rebounded. These models were developed using LS-DYNA® wherein the primary objective was to evaluate the ability of the material model MAT299 to capture the dynamic response and damage modes in the T700/LMPAEK test panels. MAT299 is a Deformation Gradient Decomposition (DGD) based Continuum Damage Mechanics (CDM) material model. The interlaminar delaminations were modeled using the cohesive contact formulation available within LS-DYNA, wherein the mixed-mode fracture is captured via the Benzegaggh-Kenane (B-K) mode-dependent fracture energy interpolation law. The above-mentioned modeling methods have mostly been applied to thermoset composites and adapting them to TPCs involves addressing challenges associated with appropriately representing material behavior. Therefore, the proposed paper would discuss the systematic approach taken to adapt thermoset composites modeling practices for applications to TPCs, while appropriately addressing material behavior. The proposed paper would show that the predicted back face center point deflection correlated reasonably well with experimental data and the peak deflection was predicted to be within 5% of the experimental measurements. The projectile rebound velocity, while predicted to be higher than the experimental measurement, was within reasonable bounds. Additionally, it will be shown that the predicted delamination shapes were in reasonable agreement with experimental data.

Composite Materials↗

Evaluation of coated columbium alloy heat shields for space shuttle thermal protection system application

A three-phase program to develop and demonstrate the feasibility of a metallic heat shield suitable for use on Space Shuttle Orbiter class vehicles at operating surface temperatures of up to 1590 K (2400 F) is summarized. An orderly progression of configuration studies, material screening tests, and subscale structural tests was performed. Scale-up feasibility was demonstrated in the final phase when a sizable nine-panel array was fabricated and successfully tested. The full-scale tests included cyclic testing at reduced air pressure to 1590 K (2400 F) and up to 158 dB overall sound pressure level. The selected structural configuration and design techniques succesfully eliminated thermal induced failures. The thermal/structural performance of the system was repeatedly demonstrated. Practical and effective field repair methods for coated columbium alloys were demonstrated. Major uncertainties of accessibility, refurbishability, and durability were eliminated.

Black, W. E.↗

Fuel containment and damage tolerance in large composite primary aircraft structures. Phase 2: Testing

Technical issues associated with fuel containment and damage tolerance of composite wing structures for transport aircraft were investigated. Material evaluation tests were conducted on two toughened resin composites: Celion/HX1504 and Celion/5245. These consisted of impact, tension, compression, edge delamination, and double cantilever beam tests. Another test series was conducted on graphite/epoxy box beams simulating a wing cover to spar cap joint configuration of a pressurized fuel tank. These tests evaluated the effectiveness of sealing methods with various fastener types and spacings under fatigue loading and with pressurized fuel. Another test series evaluated the ability of the selected coatings, film, and materials to prevent fuel leakage through 32-ply AS4/2220-1 laminates at various impact energy levels. To verify the structural integrity of the technology demonstration article structural details, tests were conducted on blade stiffened panels and sections. Compression tests were performed on undamaged and impacted stiffened AS4/2220-1 panels and smaller element tests to evaluate stiffener pull-off, side load and failsafe properties. Compression tests were also performed on panels subjected to Zone 2 lightning strikes. All of these data were integrated into a demonstration article representing a moderately loaded area of a transport wing. This test combined lightning strike, pressurized fuel, impact, impact repair, fatigue and residual strength.

Sandifer, J. P.↗

Computing Stress, Stability, And Vibration Of Shells

BOSOR4 computer program developed as comprehensive program for analysis of stress, stability, and vibration of complex, branched shells of revolution made of elastic materials. Used to analyze prismatic shells and panels. Performs large-deflection axisymmetric stress analysis, small-deflection nonsymmetric stress analysis, modal vibration analysis with axisymmetric nonlinear prestress included, and buckling analysis with axisymmetric or nonsymmetric prestress. One main advantage, provisions for such realistic engineering details as eccentric load paths, internal supports, arbitrary branching conditions, and "library" of wall constructions. Based on finite-difference energy method and offers very rapid convergence with increasing numbers of mesh points. Written in FORTRAN 77.

Bushnell, David↗

Inflow velocity perturbations due to fuselage effects in the presence of a fully interactive wake

The velocity field at locations above the plane of the rotor disk of a generic helicopter configuration has been measured experimentally and modeled using two computational models. The first computational model represents only the portion of the velocity field due to the fuselage, using only the potential due to freestream onset flow. The second model represents all elements of the problem in an incompressible field: the rotor, the rotor wake, and the non-lifting fuselage. The first model is used to assess the fidelity requirement for fuselage paneling. Comparisons are made between a much simplified body shape, an accurate body shape, a body shape with a crude hub/shaft model and wind-tunnel measurements. The second model is used to assess the relative magnitude of the velocity perturbations at the rotor disk due to the effects of the fuselage. A fully interactive time-stepping wake method is used to predict the velocities at the rotor disk. These velocities are computed with and without the fuselage in the model and compared with measured wind-tunnel inflow velocities. The difference between the velocities computed with and without the fuselage is then compared with the perturbation velocity field computed by the first method.

Berry, John D.↗

Finite element study of plate buckling induced by spatial temperature gradients

Finite element analyses of thermal buckling of thin metallic plates with prescribed spatial temperature distributions are described. Thermally induced compressive membrane stresses and transverse plate displacement imperfections initiate plates buckling. A finite element formulation based on von Karman plate theory is presented. The resulting nonlinear equations are solved for incremental temperature increases by Newton-Raphson iteration. The computational method is used to investigate the buckling response of rectangular plates with steady and unsteady spatially varying temperature distributions. The role of initial plate imperfections and temperature distributions on the nonlinear response of plate displacements and stresses is described. The relatively high levels of stress induced by spatial temperature gradients should be considered carefully in the postbuckling design of panels for aerospace vehicles subjected to combined mechanical and thermal loads.

Thornton, Earl A.↗

Contact Angle of Drops Measured on Nontransparent Surfaces and Capillary Flow Visualized

The spreading of a liquid on a solid surface is important for various practical processes, and contact-angle measurements provide an elegant method to characterize the interfacial properties of the liquid with the solid substrates. The complex physical processes occurring when a liquid contacts a solid play an important role in determining the performance of chemical processes and materials. Applications for these processes are in printing, coating, gluing, textile dyeing, and adhesives and in the pharmaceutical industry, biomedical research, adhesives, flat panel display manufacturing, surfactant chemistry, and thermal engineering.

Chao, David F.↗

Interconnnect and bonding technologies for large flexible solar arrays

Thermocompression bonding and conductive adhesive bonding are developed and evaluated as alternate methods of joining solar cells to their interconnect assemblies. Bonding materials and process controls applicable to fabrication of large, flexible substrate solar cell arrays are studied. The primary potential use of the techniques developed is on the solar array developed by NASA/MSFC and LMSC for solar electric propulsion (SEP) and shuttle payload applications. This array is made up of flexible panels approximately 0.7 by 3.4 meters. It is required to operate in space between 0.3 and 6 AU for 5 years with limited degradation. Materials selected must be capable of enduring this space environment, including outgassing and radiation.

Source record↗

Triangular Berstein-bezier Patches, a Survey and New Results

Triangular Bernstein-Bezier patches are an alternative to the standard rectangular ones. They are maps of triangular domains into R cubed, where the patches are described by control nets similar to the rectangular case. One difference in the definition of surface normals at the patch corners: rectangular patches have inherent problems with so-called degenerate corners, i.e., edges collapsing into one point. Triangular patches do not have these problems. Since triangular shapes arise rather frequently in the design of complicated surfaces (e.g., interior car body panels), it seems that for such surfaces triangular patches are a promising addition to the usually employed rectangular patches. Another major application is the formulation of interpolants to solve the scattered data problem: here Bernstein-Bezier patches provide a very powerful tool; they can be used to discover new schemes as well as to discover new properties of existing methods.

Farin, G.↗