Search NASA⌕ Search

SEARCH · Search NASA

Results for “Conversion methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Biomass conversion to produce hydrocarbon liquid fuel via hot-vapor filtered fast pyrolysis and catalytic hydrotreating

Lignocellulosic biomass conversion to produce biofuels has received significant attention because of the quest for a replacement for fossil fuels. Among the various thermochemical and biochemical routes, fast pyrolysis followed by catalytic hydrotreating is considered to be a promising near-term opportunity. This paper reports on experimental methods used 1) at the National Renewable Energy Laboratory (NREL) for fast pyrolysis of lignocellulosic biomass to produce bio-oils in a fluidized-bed reactor and 2) at Pacific Northwest National Laboratory (PNNL) for catalytic hydrotreating of bio-oils in a two-stage, fixed-bed, continuous-flow catalytic reactor. The configurations of the reactor systems, the operating procedures, and the processing and analysis of feedstocks, bio-oils, and biofuels are described in detail in this paper. We also demonstrate hot-vapor filtration during fast pyrolysis to remove fine char particles and inorganic contaminants from bio-oil. Representative results showed successful conversion of biomass feedstocks to fuel-range hydrocarbon biofuels and, specifically, the effect of hot-vapor filtration on bio-oil production and upgrading. As a result, the protocols provided in this report could help to generate rigorous and reliable data for biomass pyrolysis and bio-oil hydrotreating research.

09 BIOMASS FUELS↗
DOE OSTI2020

Predicting Device Parameters for Dye-Sensitized Solar Cells from Electronic Structure Calculations to Reproduce Experiment.

Given that improvements to the power-conversion efficiency (PCE) of dye-sensitized solar cells (DSSCs) have slowed in recent years, a means to accurately predict the device parameters yielded by trial dyes in silico, without having to synthesize them, would be extremely valuable to speed up the design process. Currently, the best-performing methods of calculating device parameters rely on a set of experimentally determined kinetic coefficients. In practice, it is very difficult to measure these kinetic parameters accurately, limiting the overall accuracy of such predictive methods. This work proposes a model to obtain key parameters such as J(SC), V-OC, and PCE using only the results from density functional theory (DFT) and time-dependent DFT calculations, noting that rates of electron-transfer steps are ultimately linked to the electronic structure of the dye center dot center dot center dot TiO2 working electrode. Six organic DSSC dyes from dissimilar chemical classes (L0, L1, L2, WS-2, WS-92, and C281) were chosen to demonstrate the power of this approach. Their a priori known experimentally determined device performance metrics served to validate our predictions. The greatest absolute error in our predicted PCE values was 0.36% relative to the experiment, while the greatest fractional error was 0.042. This indicates that the proposed model offers a dramatic improvement on previous predictive methods for DSSC device parameters, both in accuracy and in consistency. Moreover, such a predictive model has great potential to be applied to other photovoltaic applications, further enabling the design of novel, highly efficient photoactive materials.

density functional theory↗
NASA NTRS2011

Markov Chain Monte Carlo Bayesian Learning for Neural Networks

Conventional training methods for neural networks involve starting al a random location in the solution space of the network weights, navigating an error hyper surface to reach a minimum, and sometime stochastic based techniques (e.g., genetic algorithms) to avoid entrapment in a local minimum. It is further typically necessary to preprocess the data (e.g., normalization) to keep the training algorithm on course. Conversely, Bayesian based learning is an epistemological approach concerned with formally updating the plausibility of competing candidate hypotheses thereby obtaining a posterior distribution for the network weights conditioned on the available data and a prior distribution. In this paper, we developed a powerful methodology for estimating the full residual uncertainty in network weights and therefore network predictions by using a modified Jeffery's prior combined with a Metropolis Markov Chain Monte Carlo method.

Goodrich, Michael S.↗
DOE OSTI2023

Accelerated Synthesis of Ordered Mesoporous Carbons Using Plasma

Conventional ordered mesoporous carbon (OMC) production usually requires long processing times in the carbonization step to achieve desired temperatures through controlled ramps. To enable expedited materials discovery, developing advanced manufacturing capability with significantly improved throughput is highly desired. Current approaches for accelerating the synthesis of OMCs include using microwave and Joule heating. However, both methods rely on the introduction of additional components, such as microwave absorbers and electrically conductive agents, within the bulk materials to impart the ability to reach high carbonization temperatures. This work demonstrates accelerated synthesis and functionalization of OMCs through the use of a dielectric barrier discharge plasma, where carbonization can be accomplished within 15 min using 30 W plasma sources, representing more than an order of magnitude increase in polymer-to-carbon conversion kinetics compared to that of a traditionally pyrolyzed analogue. Particularly, the ability of performing rapid carbonization without the use of additional substrates within the OMC precursor systems is advantageous. A systematic investigation of how plasma power, time, and gas atmosphere impact the resulting OMC pore textures and properties is performed, demonstrating the broad applicability of plasma-enabled carbonization methods. Furthermore, we demonstrate that the plasma treatment strategy can be extended to incorporate heteroatoms into the carbon framework by introducing ammonia gas, resulting in OMCs with a nitrogen content up to 4.7 at %, as well as non-Pluronic templating systems for synthesizing OMC with pore sizes larger than 10 nm. As employing a plasma source for materials pyrolysis is an industrially relevant approach, our system can be extended toward scaled synthesis of OMCs with much faster production rates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Sn doping on partially dealuminated Beta zeolite by solid state ion exchange for 5‐hydroxymethylfurfural ( 5‐HMF ) production from glucose

Abstract BACKGROUND The conversion of glucose into 5‐hydroxymethylfurfural (5‐HMF) involves the isomerization of glucose to fructose catalyzed by Lewis acid and subsequent dehydration of fructose catalyzed by Brönsted acid. In this work, in order to obtain a high yield of 5‐HMF, a series of Sn‐Al‐Beta catalysts containing both Lewis and Brönsted acid sites were prepared by a convenient solid state ion exchange (SSIE) method using partially dealuminated Beta zeolite and tin(II) acetate. RESULTS The obtained bifunctional catalysts were investigated for one‐pot production of 5‐HMF from glucose in the ionic liquid (IL) [C 4 mim]Cl. Among various catalysts, Sn‐Al‐Beta‐ 4 ‐ 8 exhibited the best catalytic performance, giving a 5‐HMF yield of 54% under optimal reaction conditions (393 K, 2 h), along with a glucose conversion of 81%. The Sn‐Al‐Beta‐ 4‐8 catalyst and IL were regenerated by the extraction of 5‐HMF, and the reactivity was reserved after five runs of recycling. In addition to glucose, the Sn‐Al‐Beta‐ 4‐8 /[C 4 mim]Cl system was also proven to have the potential to effectively convert other carbohydrates into 5‐HMF. CONCLUSION The results suggested that the catalyst is convenient to prepare and has preferable efficiency and stability in the conversion of carbohydrates into 5‐HMF. © 2022 Society of Chemical Industry (SCI).

Zhang, Wei↗
DOE OSTI2021

Multifunctional Conjugated Ligand Engineering for Stable and Efficient Perovskite Solar Cells

Surface passivation is an effective way to boost the efficiency and stability of perovskite solar cells (PSCs). However, a key challenge faced by most of the passivation strategies is reducing the interface charge recombination without imposing energy barriers to charge extraction. Here, a novel multifunctional semiconducting organic ammonium cationic interface modifier inserted between the light-harvesting perovskite film and the hole-transporting layer is reported. It is shown that the conjugated cations can directly extract holes from perovskite efficiently, and simultaneously reduce interface non-radiative recombination. Together with improved energy level alignment and the stabilized interface in the device, a triple-cation mixed-halide medium-bandgap PSC with an excellent power conversion efficiency of 22.06% (improved from 19.94%) and suppressed ion migration and halide phase segregation, which lead to a long-term operational stability, is demonstrated. Finally, this strategy provides a new practical method of interface engineering in PSCs toward improved efficiency and stability.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Monolithic Photoelectrochemical CO 2 Reduction Producing Syngas at 10% Efficiency

We report increasing anthropogenic carbon dioxide emissions have prompted the search for photoelectrochemical (PEC) methods of converting CO 2 to useful commodity products, including fuels. Ideally, such PEC approaches will be sustained using only sunlight, water, and CO 2 as energetic and reactant inputs. However, low peak conversion efficiencies (< 5%) have made commercialization of fully-integrated PEC devices prohibitive. Here, a 4 cm 2 monolithic PEC device exceeding 10% solar-to-fuel efficiency with principal fuel products of carbon monoxide and hydrogen is reported. The corresponding solar-to-CO and solar-to-H 2 efficiencies are 7% and 3.5%, respectively. Screening of a range of operating conditions reveals a tunable product mixture of H 2 and CO using a gold electrocatalyst. Accordingly, it is shown that device optimization yields a H 2 -to-CO ratio of 1:2 commonly present in synthesis gas (syngas). Notably, the modularity and facile fabrication of this device permit the incorporation of a broad array of materials for various applications. For example, the electrocatalyst may easily be swapped to target a different set of products.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Pyrolysis of high-density polyethylene: Degradation behaviors, kinetics, and product characteristics

Pyrolysis is a promising technology for converting plastic waste into valuable raw materials while offering a potential solution to the global plastic pollution crisis. In this study, the thermal pyrolysis of high-density polyethylene (HDPE) is investigated in a drop tube reactor under nearly isothermal conditions. The impact of reaction temperature and gas/volatile residence time on carbon conversion and product distribution is examined across a range of 500–900°C and 3.6–32.2s, respectively. Non-condensable gas products detected by online mass spectrometry are H 2 , CH 4 , C 2 H 4 , C 2 H 6 , C 3 H 6 , and C 3 H 8 . At elevated temperatures and prolonged residence time, H 2 yield reaches as high as 8.6 wt% of the initial HDPE mass due to intensified cracking reactions of C 2 –C 3 hydrocarbons and long-chain aliphatic compounds. Consequently, pyrolysis tars consist mainly of polycyclic aromatic hydrocarbons (PAHs) with 5–7 rings, accompanied by visible coke deposition within the reactor. HDPE decomposition to volatiles is an endothermic process and it is complete at a temperature between 492°C and 525°C, depending on the heating rate employed, from non-isothermal thermogravimetric analysis and differential scanning calorimetry (TGA-DSC) measurements. The thermal degradation of HDPE pellets follows the two-dimensional nucleation growth model for conversion levels up to 0.8 with an apparent activation energy of 259–270 kJ/mol and a pre-exponential factor of 4.83 × 10 17 –1.37 × 10 19 min -1 , determined from various isoconversional methods such as Flynn-Wall-Ozawa (FWO), Kissinger-Akahira-Sunose (KAS), and Starink, along with Criado's master plots. Further, these findings provide valuable insights into optimizing process parameters and refining reactor design for pyrolysis, which can be integrated with gasification and reforming processes to enhance hydrogen production on a larger scale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Thermal engineering of FAPbI 3 perovskite material via radiative thermal annealing and in situ XRD

Lead halide perovskites have emerged as successful optoelectronic materials with high photovoltaic power conversion efficiencies and low material cost. However, substantial challenges remain in the scalability, stability and fundamental understanding of the materials. Here we present the application of radiative thermal annealing, an easily scalable processing method for synthesizing formamidinium lead iodide (FAPbI 3 ) perovskite solar absorbers. Devices fabricated from films formed via radiative thermal annealing have equivalent efficiencies to those annealed using a conventional hotplate. By coupling results from in situ X-ray diffraction using a radiative thermal annealing system with device performances, we mapped the processing phase space of FAPbI 3 and corresponding device efficiencies. Our map of processing-structure-performance space suggests the commonly used FAPbI 3 annealing time, 10 min at 170 degrees C, can be significantly reduced to 40 s at 170 degrees C without affecting the photovoltaic performance. Lastly, the Johnson-Mehl-Avrami model was used to determine the activation energy for decomposition of FAPbI 3 into PbI 2 .

14 SOLAR ENERGY↗
DOE OSTI2017

Tunnel Junction Development Using Hydride Vapor Phase Epitaxy

We demonstrate for the first time III-V tunnel junctions grown using hydride vapor phase epitaxy (HVPE) with peak tunneling currents >8 A/cm 2 , sufficient for operation of a multijunction device to several hundred suns of concentration. Multijunction solar cells rely on tunneling interconnects between subcells to enable series connection with minimal voltage loss, but tunnel junctions have never been shown using the HVPE growth method. HVPE has recently reemerged as a low-cost growth method for high-quality III-V materials and devices, including the growth of high-efficiency III-V solar cells. We previously showed single-junction GaAs solar cells with conversion efficiencies of ~24% with a path forward to equal or exceed the practical efficiency limits of crystalline Si. Moving to a multijunction device structure will allow for even higher efficiencies with minimal impact on cost, necessitating the development of tunnel interconnects. Here in this paper, we demonstrate the performance of both isolated HVPE-grown tunnel junctions, as well as single-junction GaAs solar cell structures with a tunnel junction incorporated into the contact region. We observe no degradation in device performance compared to a structure without the added junction.

14 SOLAR ENERGY↗
DOE OSTI2022

Review—Development of Highly Active and Stable Catalyst Supports and Platinum–Free Catalysts for PEM Fuel Cell

Metal-free, metal-containing, and template-assisted metal-containing nitrogen-modified carbon-based catalysts carbon composite supports, and highly active and electrochemically stable hybrid cathode catalysts for oxygen reduction reaction are reviewed in this manuscript. Here, novel procedures are developed for the synthesis of (i) highly catalytically active PGM-free catalyst and stable carbon composite catalyst supports. The carbon composite catalyst supports are engineered with optimized BET surface area and pore size distribution and with a well-defined kinetic and mass transfer region during the reaction and their performance is dicussed in detail in this review. The surface activation results in increasing carbon graphitization and inclusion of non-metallic active sites on the support surface. The USC catalysts exhibit the initial performance of 0.91 V and a maximum power density of 177 mW cm –2 , with well-defined kinetic and mass-transfer regions and ~2.5% H 2 O 2 production. Activated carbon composite support (ACCS) is modified to optimize its kinetic activity and its electrochemical stability shows excellent thermal stability and support stability under simulated start-up/shut-down operating conditions. The stabilities of various supports developed in this study are compared with those of a commercial Pt/C catalyst. The active sites for the ORR identified with electrochemical and physicochemical methods are pyridinic-N and quaternary-N.

25 ENERGY STORAGE↗
DOE OSTI2024

EV Champion Training Webinar 1: ZEV and EV Charging Fundamentals [Slides]

The Electric Vehicle (EV) Champion Training Series, hosted by the National Renewable Energy Laboratory (NREL), is tailored for fleet managers, facility managers, and other stakeholders involved in the deployment of EVs and charging stations. This series equips participants with the skills and knowledge necessary to become subject matter experts in EV implementation. This is the first training in a four-part series and serves as an introductory training. This training covers fundamental topics such as EV and charging technology, utility basics, and financial considerations for EVs. Additionally, this session introduces the Federal Fleet ZEV Ready Center framework, a one-stop location for federal fleet electrification resources. Participants will gain a solid foundation to support the effective deployment and management of EVs and their infrastructure. Visit the Federal Fleet ZEV Ready Center website to learn more about the ZEV Ready Center process. EV Champion Training Webinar 1: ZEV and EV Charging Fundamentals will enable attendees to: Identify EV and EV charging technology fundamentals; Recognize EV market and GSA Schedule options; Identify utility basics, incentives, and rates as they relate to EV charging; and Identify methods to calculate life cycle costs for EVs and gasoline vehicles.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS1977

Instantaneous relationship between solar inertial and local vertical local horizontal attitudes

The instantaneous relationship between the Solar Inertial (SI) and Local Vertical Local Horizontal (LVLH) coordinate systems is derived. A method is presented for computation of the LVLH to SI rotational transformation matrix as a function of an input LVLH attitude and the corresponding look angles to the sun. Logic is provided for conversion between LVLH and SI attitudes expressed in terms of a pitch, yaw, roll Euler sequence. Documentation is included for a program which implements the logic on the Hewlett-Packard 97 programmable calculator.

Vickery, S. A.↗
NASA NTRSDate not supplied

VSLAM and Coplanar POSIT for Advanced Air Mobility Approach and Landing

Advanced Air Mobility (AAM) aircraft have many challenges for landing accurately and safely in urban, suburban, and rural environments. Localization in large and open rural environments could utilize GPS, but AAM aircraft in urban environments will encounter GPS degradation. Another challenge involves flight operation time, i.e., flying during the day or at night. There are different types of guidelines and landmarks at runways, heliports, and vertiports for daytime and nighttime applications. Tailoring feature detection methods for AAM approach and landing during the day and night pose different issues and challenges. It is easier to detect edges, lines, and other runway markers during the day than at night. Conversely, it is easier to detect landing light configurations and patterns at nighttime than daytime. Consequently, utilizing the same feature detector for daytime and nighttime operations may not be feasible. This paper focuses on vision-based precision approach and landing (PAL) and builds on previous work by comparing ORB SLAM, custom VSLAM, and coplanar pose from orthography and scaling with iterations (POSIT) for daytime and nighttime operations. Implementing high fidelity simulations with computer graphics and extracting video frames from flight test data provide promising results for AAM PAL applications.

Evan Kawamura↗
DOE OSTI2022

MEA Manufacturing R&D

This is our annual presentation on the HFTO-funded MEA Manufacturing R&D project, mainly focused on development of in-line quality inspection methods for high volume fabrication of fuel cell and electrolysis MEA materials.

DIRECT ENERGY CONVERSION,ENGINEERING↗
DOE OSTI2026

Author Correction: US oil and gas system emissions from nearly one million aerial site measurements

Correction to: Naturehttps://doi.org/10.1038/s41586-024-07117-5 Published online 13 March 2024 In the version of the article initially published, several errors were present and have been corrected in the HTML and PDF versions of the article and Supplementary Information. The main results, conclusions, and our interpretations of the data remain unchanged. See the new Supplementary Information Section S15 for a more detailed description of the errors corrected and the resulting effects on the analysis. Data processing and methods corrections Overflight count correction: We previously used pre-computed source coverage data for some Carbon Mapper campaigns that was computed differently than was required for our analysis. We have re-computed Carbon Mapper source coverage based on flightline polygons and source coordinates. Transition point computation, well sites: The updated version now correctly compares the cumulative emissions distribution of simulated well site emissions with that of aerially detected sources (rather than plumes) when computing the transition point. Transition point computation, midstream: Additionally, the transition point calculation has been corrected to exclude aerially detected midstream emissions below the transition point, which was previously leading to double counting of these emissions. This error was not present for upstream (well site) emissions. Calculation errors Unit error: We corrected a specific unit conversion error affecting well site emissions in the Kairos Fort Worth dataset. Across all datasets, we also correct the conversion factor for converting from standard volume to mass for midstream emissions. Sorting error: We correct code that was applying incorrect sorting when computing correction factors to account for partial detection at well sites. Small typographical corrections were made in Fig. 1b and SI Section S4.1. Data processing and methods corrections Overflight count correction: We previously used pre-computed source coverage data for some Carbon Mapper campaigns that was computed differently than was required for our analysis. We have re-computed Carbon Mapper source coverage based on flightline polygons and source coordinates. Transition point computation, well sites: The updated version now correctly compares the cumulative emissions distribution of simulated well site emissions with that of aerially detected sources (rather than plumes) when computing the transition point. Transition point computation, midstream: Additionally, the transition point calculation has been corrected to exclude aerially detected midstream emissions below the transition point, which was previously leading to double counting of these emissions. This error was not present for upstream (well site) emissions. Calculation errors Unit error: We corrected a specific unit conversion error affecting well site emissions in the Kairos Fort Worth dataset. Across all datasets, we also correct the conversion factor for converting from standard volume to mass for midstream emissions. Sorting error: We correct code that was applying incorrect sorting when computing correction factors to account for partial detection at well sites. Small typographical corrections were made in Fig. 1b and SI Section S4.1. The following practices may help researchers conducting similar analyses avoid making similar errors: 1, Clear, accessible documentation explaining the interpretation of all columns in data input tables and all internal variables within the model, 2, Simple cross-check calculations computed before and after unit conversions.

Sherwin, Evan D↗
DOE OSTI2020

Multimodal Analysis of Reaction Pathways of Cathode Materials for Lithium Ion Batteries

Conversion mechanism in lithium ion batteries provides higher capacity than intercalation mechanism since multiple numbers of electrons and lithium ions are associated. However, poor cycling stability, large voltage hysteresis, and low energy efficiency have been great challenges of conversion reaction. To address those issues, conversion-type electrode materials have been reformed via doping or substituting other elements. For example, iron fluorides (FeF 2 , FeF 3 ) have modified as iron oxyfluorides (FeF 1-x O x ), showing enhanced long-term stability. Furthermore, co-substituted (both anion and cation substituted) Fe 0.9 Co 0.1 OF (FeCoOF) was demonstrated excellent cycling stability. (capacity of 350 mAh g -1 at a current of 500 mA g -1 for 1000 cycles). Substituting anion and cation in iron fluoride has been suggested as an effective method to achieve better reversibility but understanding of lithiation reactions in co-substituted FeCoOF is not clear. This work takes advantage of ex-situ/ in-situ synchrotron X-ray based techniques and transmission electron microscopy to elucidate structural changes with lithium ion, which may provide fundamental insights into modifying conversion-type materials. Figure 1 presents discharge-charge curves and pair distribution function patterns acquired at each potential. As lithium ions were inserted, structural changes were noticed both at short-range and long-range. However, long-range ordering was nearly maintained even at 1 V, indicating absence of conversion reaction. Figure 2 shows lithiation induced structural evolution of a single FeCoOF nanorod observed in real time. As lithiation proceeds, the width of nanorods shows a stepwise increase, particularly A in figure 2d, which may indicate multiple steps of lithiation occur. Considering that conversion reaction takes place around 2 V in FeF 3 , co-substitution Co and O into iron fluoride may change thermodynamic features of lithiation reactions by lowering the initiation potential for conversion reaction. Instead, phase transformations occur at long-range order, which may help maintaining structural integrity during operation, eventually, achieving cycling stability.

25 ENERGY STORAGE↗
NASA NTRS2017

Strategic Employee Development in The Government Sector

As with many other U.S. agencies, succession planning is becoming a critical need for NASA. The primary drivers include (a) NASA's higher-than-average aged workforce with approximately 50% of employees eligible for retirement within 5 years; and (b) employees who need better developmental conversations to increase morale and retention. This problem is particularly concerning for Safety & Mission Assurance (S&MA) organizations since they traditionally rely on more experienced engineers and specialists to perform their organizations' functions. In response to this challenge, the Kennedy Space Center (KSC) S&MA organization created the Strategic Employee Development (SED) program. The SED program's goal is to provide a proactive method to counter the primary drivers by creating a deeper "bench strength" and providing a more comprehensive developmental feedback experience for the employee. The SED is a new succession planning framework that enables customization to any organization, and in this case, specifically for an S&MA organization. This is accomplished via the identification of key positions, the corresponding critical competencies, and a process to help managers have relevant and meaningful development conversations with the workforce. As a result of the SED, several tools and products were created that allows management to make better strategic workforce decisions. Although there are opportunities for improvement for the SED program, the most important impact has been on the quality of developmental discussions for employees.

Nguyen, Johnny↗