Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dislocation structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76

High Thermoelectric Performance through Crystal Symmetry Enhancement in Triply Doped Diamondoid Compound Cu 2 SnSe 3

The presence of high crystallographic symmetry and nanoscale defects are favorable for thermoelectrics. With proper electronic structures, a highly symmetric crystal tends to possess multiple carrier channels and promote electrical conductivity without sacrificing Seebeck coefficient. In addition, nanoscale defects can effectively scatter acoustic phonons to suppress thermal conductivity. Here, we report that the triple doping of Cu 2 SnSe 3 leads to a high ZT value of 1.6 at 823 K for Cu 1.85 Ag 0.15 (Sn 0.88 Ga 0.1 Na 0.02 )Se 3 , and a decent average ZT (ZT ave ) value of 0.7 is also achieved for Cu 1.85 Ag 0.15 (Sn 0.93 Mg 0.06 Na 0.01 )Se 3 from 475 to 823 K. Our study reveals: (1) Ag doping on Cu sites generates numerous point defects and greatly decreases lattice thermal conductivity. (2) Doping Mg or Ga converts the monoclinic Cu 2 SnSe 3 into a cubic structure. This symmetry enhancing leads to increase in the effective mass from 0.8 m e to 2.6 m e (m e , free electron mass) and the power factor from 4.3 μW/cm –1 K –2 for Cu 2 SnSe 3 to 11.6 μW/cm –1 K –2 . (3) Na doping creates dense dislocation arrays and nanoprecipitates, which strengthens the phonon scattering. (4) Pair distribution function analysis shows localized symmetry breakdwon in the cubic Cu 1.85 Ag 0.15 (Sn 0.88 Ga 0.1 Na 0.02 )Se 3 . Furthermore, the present work provides a standpoint to design promising thermoelectric materials by synergistically manipulating crystal symmetry and nanoscale defects.

36 MATERIALS SCIENCE↗

Diffusion of small anti-Schottky clusters in UO 2

The aggregation of irradiation-induced defect clusters in UO 2 leads to the formation of dislocation loops and cavities which contribute swelling and ultimately produce deleterious effects on the fuel. Despite their fundamental role in fuel evolution, the kinetics of these defect clusters are not currently well understood. In this work, we investigate the diffusive behavior of interstitial clusters via Molecular Dynamics (MD) simulations. In this work, our investigation considers a range of defect cluster sizes, each composed of N UO 2 units or anti-Schottky defects. We report a complex cluster size - mobility relation; increasing cluster size corresponds to an increase in mobility up until a critical size (N=4) where diffusivity reaches a maximum, after which the trend reverts and further increasing size corresponds to a decrease in mobility. The rapid migration observed correlates well with the very low barriers reported in a few historic experimental studies. Further analysis of the cluster shape and orientation reveals a strong structural preference for near-planar configurations oriented normal to the $\langle$100$\rangle$ direction. Rotational energy barriers are found to be similar in both magnitude and trend to the observed diffusion barriers. Lastly, connections are drawn to the behavior of large defect clusters including the formation of (1/3) $\langle$111$\rangle$ Frank dislocation loops.

36 MATERIALS SCIENCE↗

Unraveling cyclic deformation mechanisms of a rolled magnesium alloy using in situ neutron diffraction

In the current study, the deformation mechanisms of a rolled magnesium alloy were investigated under cyclic loading using real-time in situ neutron diffraction under a continuous-loading condition. The relationship between the macroscopic cyclic deformation behavior and the microscopic response at the grain level was established. The neutron diffraction results indicate that more and more grains are involved in the twinning and detwinning deformation process with the increase of fatigue cycles. The residual twins appear in the early fatigue life, which is responsible for the cyclic hardening behavior. The asymmetric shape of the hysteresis loop is attributed to the early exhaustion of the detwinning process during compression, which leads to the activation of dislocation slips and rapid strain-hardening. The critical resolved shear stress for the activation of tensile twinning closely depends on the residual strain developed during cyclic loading. In the cycle before the sample fractured, the dislocation slips became active in tension, although the sample was not fully twinned. The increased dislocation density leads to the rise of the stress concentration at weak spots, which is believed to be the main reason for the fatigue failure. Furthermore, the deformation history greatly influences the deformation mechanisms of hexagonal-close-packed-structured magnesium alloy during cyclic loading.

36 MATERIALS SCIENCE↗

Evaluation of strain caused by coherent precipitates in an Al alloy using TEM techniques

Elastic strains, caused by GP zones in an aged Al alloy, were determined quantitatively using two techniques: Dark Field In-line Holography (DFH) and High Resolution Transmission Electron Microscopy-Geometric Phase Analysis (HRTEM-GPA). The results obtained by both techniques showed that the elastic strain was not uniform along the precipitate-matrix interface. In some areas, it was found that strain had negligible value and this was attributed to the loss of coherence between the lattices. It is suggested that a possible explanation for this fact could be a variation in the 'vacancies pump mechanism' kinetics. To obtain a better interpretation of the experimental deformation maps, a reference GP precipitate-matrix structure was built using QSTEM software. The main advantages of DFH over HRTEM-GPA were a bigger field of view and low electron dose requirements without spatial resolution loss. Another difference found was that crystalline defects such as dislocations were evidenced by HRTEM-GPA in contrast to the result obtained by DFH. However, strain measurements were affected by mask size effect in the former. - Highlights: Black-Right-Pointing-Pointer Strain around GP precipitates was not uniform and was in a more relaxed state. Black-Right-Pointing-Pointer Strain values determined by HRTEM had more artifacts compared with holography ones. Black-Right-Pointing-Pointer Strain distribution was attributed to differences in the release of vacancies. Black-Right-Pointing-Pointer Holography showed important advantages over HRTEM regarding field of view mainly.

36 MATERIALS SCIENCE↗

Strain Accommodation By Facile WO6 Octahedral Distortion and Tilting During WO3 Heteroepitaxy on SrTiO3(001)

In this paper, we show that compared to other BO6 octahedra in ABO3 structured perovskite oxides, the WO6 octahedra in tungsten trioxide (WO3) can withstand a much larger degree of distortion and tilting to accommodate interfacial strain, which in turn strongly impact the nucleation, structure, and defect formation during the epitaxial growth of WO3 on SrTiO3(001). A meta-stable tetragonal phase can be stabilized by epitaxy and a thickness dependent phase transition (tetragonal to monoclinic) is observed. In contrast to misfit dislocations to accommodate the interfacial stain, the facial WO6 octahedral distortion and tilting give rise to three types of planar defects that affect more than 15 monolayers from the interface. These atomically resolved, unusual interfacial defects may significantly alter the electronic, electrochromic, and mechanical properties of the epitaxial films.

Environmental Molecular Sciences Laboratory↗

The Effect of the Method by Which a High-Resistivity GaN Buffer Layer Is Formed on Properties of InAlN/GaN and AlGaN/GaN Heterostructures with 2D Electron Gas

AlGaN/AlN/GaN and InAlN/AlN/GaN structures with 2D electron gas have been grown on sapphire substrates by metal-organic vapor-phase epitaxy. The suppression of the parasitic conductivity of buffer GaN layers was provided either by intentionally raising the density of edge dislocations or by doping with iron (GaN:Fe). It was shown that using GaN buffer layers with a better crystal perfection and more planar surface results in the electron mobility in the 2D channel for carriers becoming 1.2–1.5 times higher.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Collaborative Research: The Role of Grain Boundary Structure and Chemistry in Materials Failure

Throughout the one year duration of this award significant progress was made in understanding the effect of grain boundaries in polycrystalline materials. The starting point of this work is that each grain boundary can be characterized by an interface energy and respective interface parameter, which depend on the boundary chemical composition and structure. As this is a new point of view for treating grain boundaries, an interdisciplinary approach was followed to prove the existence of such interface terms. Throughout the project, hence, theory, experiments and simulations were used. Molecular dynamics and dislocation density-function dynamics were performed to understand dislocation-grain boundary interactions in pure Al crystalline materials, as potentials for Al are well established. The formation of dislocation pile-ups was observed and the strain profiles were in agreement with interfacial gradient plasticity, which is the theoretical framework that allows the introduction of mechanically induced interface energies. After verifying numerically the existence of mechanically induced interface energies, nanoindentation experiments were performed near grain boundaries of Fe-Si crystals that contained three grain boundaries. By indenting in close proximity to the boundary these experiments allowed for measuring the critical stress at which deformation was transmitted across the boundary to the adjacent grains, either through dislocation transmission or absorption and subsequent emission. This critical stress, also termed grain boundary yield stress, was in accordance with the value predicted by interfacial gradient plasticity, further verifying that mechanically induced interface energies can help define the material response. In the Fe-Si crystals the Si content was kept constant at 3wt%, but three specimen were considered each of which was characterized by a different misorientation at the grain boundary. By relating the experiments with the analytical gradient plasticity expressions it was possible to obtain first estimates for the interface parameter as ~200N/m. This value was not proportional to the misorientation angle, but depended also on the grain boundary plane. The continuation of this project is performing more detailed experiments on additional Fe-Si and Fe-C systems (both nanoindentation and in-situ transmission electron microscopy) to further understand the physical origin of such interface parameters. Furthermore, molecular dynamics nanoindentation simulations are also performed on similar systems to better understand the dislocation grain boundary interactions.

36 MATERIALS SCIENCE↗

Redistribution of Ti and Al in deuterium charged TiAl

The redistribution of titanium and aluminum in a single-phase TiAl alloy that has been exposed to a high pressure of deuterium gas at high temperature is studied. The microstructure in the as-received, uncharged condition consisted of single-phase gamma TiAl grains and a random distribution of precipitates. Precipitates were distributed throughout the matrix and along the grain boundaries. The chemistry of the precipitates varied considerably; some were rich in Al, while other were mostly Ti with some Si and Al. The dislocation density in most grains was low, although in a few grains a high dislocation density was observed. FCC deuterides with a lattice parameter of 0.45 nm form in a Ti-52.1Al-2.1Ta (at. pct) alloy after exposure to 1.38 MPa of deuterium gas at 650 C for 213 hr. The structure and lattice parameter are consistent with the formation of Ti(l)D2. The deuterides that form in this alloy are enriched in Ti and deficient in Al and Ta compared to the deuteride-free matrix. Regions of the matrix contiguous with the deuterides have a correspondingly enhanced aluminum and tantalum concentration.

Legzdina, D.↗

Parameter development and characterization of laser powder directed energy deposition of Nb – Alloy C103 for thin wall geometries

This work focuses on the parameter development and microstructural characterization of Nb-based alloy C103 for thin wall structures produced via laser powder – directed energy deposition (LP – DED). Laser power and scanning speeds were varied as part of a design of experiments to identify adequate print parameters. Combinations were evaluated for relative density, porosity, and geometrical accuracy. A combination of a laser power of 1420 W and scanning speed of 14 mm/s resulted in a relative density >99%, exhibited a consistent weld bead profile and was used for further microstructural evaluation. A mix of optical and scanning electron microscopy (SEM) revealed small, slightly elongated grains along the edges and large epitaxial grains in the central region along the Build – Transverse view. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) analysis revealed Hf rich columnar cells in the center that transition into an evenly spaced cellular structure towards the edges of the built sample. Electron backscatter diffraction (EBSD) scans show a sharp [001] texture when looking at the cross section of the sample along the build direction. The Build – Scan view revealed a zig – zag pattern that follows the back – and – forth deposition strategy that was used. Finally, microhardness measurements were taken in the as – built (AB) and stress relieved (SR) conditions to baseline preliminary mechanical properties. The AB condition exhibited a large amount of scatter in the data and averages up to 11% larger than the SR condition. The reduction in scatter upon applying the SR cycle are indicative of a large concertation of dislocations present in the AB condition.

36 MATERIALS SCIENCE↗

The Impact of Rolling at Temperature on Conductivity and Texture in Nanolamellar Cu/Nb Bimetallic Composites

We report warm rolling is used to identify whether reductions in dislocation content would provide a significant impact on conductivity in accumulatively roll-bonded Cu-Nb nanolaminates. In addition, the impact of temperature on mechanical properties and interfacial texture is also quantified. Although temperature has a strong effect on dislocation content and mechanical properties, it is shown that length scale and volume fraction are most critical to defining the conductivity of the nanolaminate. Rolling at temperature reduced the flow stress of the material while maintaining the interfacial and layer structure, indicating that warm rolling can increase the ability to process the nanolaminates without reducing conductivity.

36 MATERIALS SCIENCE↗

Microstructure and nanohardness distribution in a polycrystalline Zn deformed by high strain rate impact

Polycrystalline Zn with an average grain size of about 300 {mu}m was deformed by direct impact Hopkinson pressure bar at a velocity of 29 m/s. An inhomogeneous grain structure was found consisting of a center region having large average grain size of 20 {mu}m surrounded by a fine-grained rim with an average grain size of 6 {mu}m. Transmission electron microscopy investigations showed a significant dislocation density in the large-grained area while in the fine-grained rim the dislocation density was negligible. Most probably, the higher strain yielded recrystallization in the outer ring while in the center only recovery occurred. The hardening effect of dislocations overwhelms the smaller grain size strengthening in the center part resulting in higher nanohardness in this region than in the outer ring. - Graphical Abstract: (a): EBSD micrograph showing the initial microstructure of polycrystalline Zn that was subsequently submitted to high strain rate impact. (b): an inhomogeneous grain size refinement was obtained which consists of a central coarse-grained area, surrounded by a fine-grained recrystallized rim. The black arrow points to the disc center. Research Highlights: {yields} A polycrystalline Zn specimen was submitted to high strain rate impact loading. {yields} Inhomogeneous grain refinement occurred due to strain gradient in impacted sample. {yields} A fine-grained recrystallized rim surrounded the coarse-grained center of specimen. {yields} The coarse-grained center exhibited higher hardness than the fine-grained rim. {yields} The higher hardness of the center was caused by the higher dislocation density.

36 MATERIALS SCIENCE↗

Denoising atomic resolution 4D scanning transmission electron microscopy data with tensor singular value decomposition

Tensor singular value decomposition (SVD) is a method to find a low-dimensional representation of data with meaningful structure in three or more dimensions. Here, tensor SVD has been applied to denoise atomic-resolution 4D scanning transmission electron microscopy (4D STEM) data. On data simulated from a SrTiO 3 [100] perfect crystal and a Si [110] edge dislocation, tensor SVD achieved an average peak signal-to-noise ratio (PSNR) of ~40 dB, which matches or exceeds the performance of other denoising methods, with processing times at least 100 times shorter. On experimental data from SrTiO 3 [100] and LiZnSb [11 2 ¯ 0]/GaSb [110] samples, tensor SVD denoises multiple GB 4D STEM data sets in ten minutes on a typical personal computer. Denoising with tensor SVD improves both convergent beam electron diffraction patterns and virtual-aperture annular dark field images.

36 MATERIALS SCIENCE↗

Room temperature creep in metals and alloys

Time dependent deformation in the form of creep and stress relaxation is not often considered a factor when designing structural alloy parts for use at room temperature. However, creep and stress relaxation do occur at room temperature (0.09-0.21 T m for alloys in this report) in structural alloys. This report will summarize the available literature on room temperature creep, present creep data collected on various structural alloys, and finally compare the acquired data to equations used in the literature to model creep behavior. Based on evidence from the literature and fitting of various equations, the mechanism which causes room temperature creep is found to include dislocation generation as well as exhaustion.

36 MATERIALS SCIENCE↗

Tensile Properties of Austenitic Stainless Steel Tubing with Internal Hydrogen/Tritium

Can microstructure explain the observed influence of hydrogen/tritium on tensile ductility? • Hydrogen is believed to interact with dislocations, grain boundaries, vacancies, and other microstructural features2 • How hydrogen and helium (He) interact with austenitic stainless steels remains a vigorous debate • We hypothesize that: • Hydrogen isotopes and decay helium act like solutes strengthening the steel and promoting planar deformation structures that reduce tensile ductility • These changes in mechanical behavior are not the same for differing microstructures

Wieber, Natalie↗

Structural defect characterization of silicon dendritic web ribbons

An EBIC study of the cross section of silicon dendritic web ribbon has revealed that recombination-active structural defects are mainly concentrated in the inner part of the ribbon, particularly at and near the twin plane, whereas the material near the surface has significantly fewer defects. An analysis of the distribution of etch pits due to slip dislocations created by shear stress indicates that a minimum in the dislocation density is frequently observed in the ribbon adjacent to the dendrite.

Cheng, L. J.↗

The Cyclic Stress-Strain Behavior of a Single Crystal Nickel-Base Superalloy

The cyclic stress-strain response and similar deformation structures of the single crystal nickel based superalloy was described under a specific set of conditions. The isothermal low cycle fatigue response and deformation structures were described at a typical intermediate temperature and at high temperature. Specimens oriented near the (001) and (111) crystallographic orientations were tested at 1050 C, where more moderate orientation effects were expected. This enabled the description of the deformation structures at each of the 2 temperatures and their relationship to the observed cyclic stress-strain behavior. The initial yield strength of all specimens tested at 650 C was controlled by the shearing of the gamma prime precipitates by dislocation pairs. Low cycle fatigue tests at 650 C had cyclic hardening, which was associated with dislocation interactions in the gamma matrix. The initial yield strength of specimens tested at 1050 C was associated with dislocation bypassing of the gamma prime precipitates. Low cycle fatigue tests at 1050 C had cyclic softening, associated with extensive dislocation recovery at the gamma-gamma prime interfaces along with some gamma prime precipitate coarsening.

Gabb, Timothy P.↗

Towards a multiscale approach for understanding irradiation induced swelling and creep in 316 stainless steels - A coupled cluster dynamics and crystal plasticity approach

Structural materials undergo mechanical degradation, in part due to irradiation-induced swelling and creep, under nuclear reactor conditions. While swelling results from the migration and clustering of irradiation-induced atomic-scale mobile defects, the interaction of mesoscale dislocations with these defects causes creep deformation. A coupled crystal plasticity (CP) and mean-field cluster dynamics (CD) approach is presented to investigate the effect of irradiation on the long-term mechanical behavior of 316 stainless steel, which are under consideration for use in nuclear reactors. The temporal evolution of Frenkel pairs and extended defect population, under a chosen irradiation flux and temperature, is predicted using the CD model. The impact of the irradiation defects on the stress state, and the resulting dislocation-mediated inelastic deformation, is modeled concurrently with the CP model. The inelastic deformation is irradiation flux dependent, and early-stage defect evolution determines the later-stage mechanical behavior in 316 stainless steel.

36 - MATERIALS SCIENCE↗

Mitigation of tin whisker growth by inserting Ni nanocones

Highlights: • Tin whisker growth is mitigated effectively by inserting Ni nanocones. • Ni nanocones impede Sn dynamic recrystallization by blocking dislocation motions. • The inhibition method and mechanism are important to the study of tin whisker. - Abstract: An innovative controllable way has been proposed to mitigate tin whisker growth by inserting Ni nanocones prepared by electrodeposition. The results reveal that, after inserting Ni nanocones, tin whisker formation is mitigated effectively for 1.6 μm Sn coating but there is no inhibition effect for 4.5 μm Sn coating. The coatings are characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectrometer and electron backscatter diffraction (EBSD). The EBSD results show that Sn grain size without Ni nanocones increases significantly after indentation test compared with Sn grains with Ni nanocones. The inhibition effect of Ni nanocones on whisker growth can be ascribed to its specific structure which prevents dynamic recrystallization and produces horizontal grain boundaries of Sn grains. The structural inhibition method and mechanism proposed are of great importance to the research of tin whisker.

77 NANOSCIENCE AND NANOTECHNOLOGY↗