Search NASA⌕ Search

SEARCH · Search NASA

Results for “Integrated Applications”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76
All sourcesNASA NTRSDOE OSTI
DOE OSTI2014

Influence of gas injection location and magnetic perturbations on ICRF antenna performance in ASDEX Upgrade

In ASDEX Upgrade H-modes with H{sub 98}≈0.95, similar effect of the ICRF antenna loading improvement by local gas injection was observed as previously in L-modes. The antenna loading resistance R{sub a} between and during ELMs can increase by more than 25% after a switch-over from a deuterium rate of 7.5⋅10{sup 21} D/s injected from a toroidally remote location to the same amount of deuterium injected close to an antenna. However, in contrast to L-mode, this effect is small in H-mode when the valve downstream w.r.t. parallel plasma flows is used. In L-mode, a non-linearity of R{sub a} at P{sub ICRP}<30 kW is observed when using the gas valve integrated in antenna. Application of magnetic perturbations (MPs) in H-mode discharges leads to an increase of R{sub a}>30% with no effect of spectrum and phase of MPs on R{sub a} found so far. In the case ELMs are fully mitigated, the antenna loading is higher and steadier. In the case ELMs are not fully mitigated, the value of R{sub a} between ELMs is increased. Looking at the W source modification for the improved loading, the local gas injection is accompanied by decreased values of tungsten (W) influx Γ{sub W} from the limiters and its effective sputtering yield Y{sub w}, with the exception of the locations directly at the antenna gas valve. Application of MPs leads to increase of Γ{sub W} and Y{sub w} for some of the MP phases. With nitrogen seeding in the divertor, ICRF is routinely used to avoid impurity accumulation and that despite enhanced Γ{sub W} and Y{sub W} at the antenna limiters.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2014

Influence of graphene on quality factor variation in a silicon ring resonator

Selectively patterned graphene is integrated onto a silicon ring resonator to investigate the quality factor (Q factor) variation. The Q factor sharply decreases from 7900 to 1200 as the patterned graphene length increases from 0 to 20 μm. A numerical estimation, which takes into account optical absorption by graphene, shows an exponential damping of the Q factor with increasing graphene length and is consistent with the experimental result. We expect these fundamental characterizations to be helpful in developing graphene-integrated silicon photonics applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2014

High Q silicon carbide microdisk resonator

We demonstrate a silicon carbide (SiC) microdisk resonator with optical Q up to 5.12 × 10{sup 4}. The high optical quality, together with the diversity of whispering-gallery modes and the tunability of external coupling, renders SiC microdisk a promising platform for integrated quantum photonics applications.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Tuning the external optical feedback-sensitivity of a passively mode-locked quantum dot laser

The external optical feedback-sensitivity of a two-section, passively mode-locked quantum dot laser operating at elevated temperature is experimentally investigated as a function of absorber bias voltage. Results show that the reverse-bias voltage on the absorber has a direct impact on the damping rate of the free-running relaxation oscillations of the optical signal output, thereby enabling interactive external control over the feedback-response of the device, even under the nearly resonant cavity configuration. The combination of high temperature operation and tunable feedback-sensitivity is highly promising from a technological standpoint, in particular, for applications requiring monolithic integration of multi-component architectures on a single chip in order to accomplish, for instance, the dual-objectives of stable pulse quality and isolation from parasitic reflections.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

Interferometric properties of standing spin waves and the application to a phase comparator

We numerically studied the material and structural parameter dependence of interferometric properties of the standing spin wave resonance (SSWR) by micromagnetic simulations and demonstrate the feasibility of practical application to an integrated phase comparator. The micromagnetic configuration of the synthesized SSWR emitted from the two microwave currents flowing through the parallel strip lines depends on the phase difference Δϕ between them. Resultantly, the Δϕ is converted to the related output voltage with an overlaid phase detector, inductively coupled to the magnetic strip. Among the investigated various material systems, low damping (α ∼ 0.001) metallic ferromagnets are found to exhibit superior device performance due to the reduced viscous dissipation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

A spin-optoelectronic detector for the simultaneous measurement of the degree of circular polarization and intensity of a laser beam

Simultaneous measurement of the degree of circular polarization and intensity of a laser beam is essential in advanced photonic applications. However, it is not feasible with conventional helicity dependent detectors where an additional detector is needed to measure the intensity. Here, we report the development of a spin-optoelectronic detector that can measure the degree of circular polarization and the intensity of a laser beam simultaneously. The principle of operation of device is based on the two independent fundamental phenomena occurring in Au/InP hybrid structures, namely, Inverse Spin Hall Effect (ISHE) and the Photo-Voltaic (PV) Effect. The magnitude of ISHE and PV signals is simultaneously measured across the two pairs of contacts that are made on the top of device. No cross talk is observed between the two detectors made on the same chip. The all-electronic compact device is fast, operates at room temperature, and opens up the possibility of many applications in an integrated optoelectronic platform.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

Electrically tunable optical bistability based on one-dimensional photonic crystals with nonlinear nanocomposite materials

A one-dimensional photonic crystal structure with a nonlinear metal-dielectric nanocomposite defect layer is proposed to control the optical bistability (OB) of the transmitted wave by tuning the externally applied dc electric field. Using the transfer matrix method for dielectric layers and solving the Helmholtz nonlinear equation in the nonlinear composite layer, the linear transmittance spectrum and the nonlinear transmission curve are illustrated graphically for different applied fields. A field-dependent defect mode is observed in the linear transmittance spectrum. Consequently, the OB switch-up and -down thresholds can be manipulated via the applied field intensity. Due to the field dependence of composite layer refractive index, the physical response of the observation is the dynamical shifting of the defect mode. Moreover, it is shown that the volume fraction, shape, and type of the embedded nanoparticles as well as the kind of the dielectric host have large influences on the OB threshold. The proposed structure has significant potential applications in optical integrated devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

Ultra-small and broadband polarization splitters based on double-slit interference

An ultra-small and broadband polarization splitter is numerically and experimentally demonstrated based on the double-slit interference in a polymer-film-coated double-slit structure. The hybrid slab waveguide (air-polymer-Au) supports both the transverse-magnetic and transverse-electric modes. The incident beam from the back side can excite these two guided modes of orthogonally polarized states in the hybrid structure. By exploiting the difference slit widths and the large mode birefringence, these two guided modes propagate to the opposite directions along the front metal surface. Moreover, the short interference length broadens the operation bandwidth. Experimentally, a polarization splitter with a lateral dimension of only about 1.6 μm and an operation bandwidth of 50 nm is realized. By designing the double-slit structure in a hybrid strip waveguide, the device dimension can be significant downscaled to about 0.3 × 1.3 μm{sup 2}. Such an ultra-small and broadband polarization splitter may find important applications in the integrated photonic circuits.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

2D materials-assisted heterogeneous integration of semiconductor membranes toward functional devices

Heterogeneous integration techniques allow the coupling of highly lattice-mismatched solid-state membranes, including semiconductors, oxides, and two-dimensional materials, to synergistically fuse the functionalities. The formation of heterostructures generally requires two processes: the combination of crystalline growth and a non-destructive lift-off/transfer process enables the formation of high-quality heterostructures. Although direct atomic interaction between the substrate and the target membrane ensures high-quality growth, the strong atomic bonds at the substrate/epitaxial film interface hinder the non-destructive separation of the target membrane from the substrate. Alternatively, a 2D material-coated compound semiconductor substrate can transfer the weakened (but still effective) surface potential field of the surface through the 2D material, allowing both high-quality epitaxial growth and non-destructive lift-off of the grown film. This Perspective reviews 2D/3D heterogeneous integration techniques, along with applications of III–V compound semiconductors and oxides. Here, the advanced heterogeneous integration methods offer an effective method to produce various freestanding membranes for stackable heterostructures with unique functionalities that can be applied to novel electrical, optoelectronic, neuromorphic, and bioelectronic systems.

2D materials↗
DOE OSTI2023

A nanocryotron memory and logic family

The development of superconducting electronics based on nanocryotrons has been limited so far to few device circuits, in part due to the lack of standard and robust logic cells. Here, we introduce and experimentally demonstrate designs for a set of nanocryotron-based building blocks that can be configured and combined to implement memory and logic functions. The devices were fabricated by patterning a single superconducting layer of niobium nitride and measured in liquid helium on a wide range of operating points. The tests show 10 - 4 bit error rates with above ± 20 % margins up to 50 MHz and the possibility of operating under the effect of an out-of-plane 36 mT magnetic field, with ± 30 % margins at 10 MHz. Additionally, we designed and measured an equivalent delay-flip-flop made of two memory cells to show the possibility of combining multiple building blocks to make larger circuits. These blocks may constitute a solid foundation for the development of nanocryotron logic circuits and finite-state machines with potential applications in the integrated processing and control of superconducting nanowire single-photon detectors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Vacancy complexes in Cd 3 As 2

Epitaxial growth of the three-dimensional topological semimetal Cd 3 As 2 on semiconductor substrates enables its use and integration in device applications. Epitaxy also provides an avenue for varying and controlling point defects through modification of the chemical potential during growth. In turn, knowledge of the point defects that are generated in Cd 3 As 2 epilayers will aid the interpretation of electron transport behavior and guide growth efforts to produce material with low defect densities. Point defects in Cd 3 As 2 epilayers grown by molecular beam epitaxy with varying As/Cd flux ratios are probed by positron annihilation spectroscopy. We find that lower As/Cd flux ratios produce higher concentrations of point defects. Remarkably, the measurements indicate that the average defect size is larger than a monovacancy. The data presented here contribute to an evolving picture of vacancy point defects in Cd 3 As 2 and can be used to direct future investigation of the defect-transport relationships in this emerging electronic material.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Thickness scaling and ferroelectric switching in wurtzite structure zinc magnesium oxide thin films

This study reports the thickness scaling of sputtered ferroelectric Zn 0.61 Mg 0.39 O (ZMO) thin films down to 43 nm. Encapsulated IrO 2 /ZMO/Ir capacitors exhibited switchable polarizations exceeding 50 μC cm −2 and coercive fields that increased from 3.9 to 4.4 MV cm −1 as the thickness decreased. Switching kinetics are best described by the simultaneous non-linear nucleation and the growth model. Bimodal switching is prevalent at low thicknesses, with the fastest switching times measured to be approximately 400 ns. Device encapsulation made ZMO switching kinetics more abrupt, potentially due to changes in the concentration of atmosphere-induced defects such as hydroxides. These results demonstrate stable ferroelectricity and sub-microsecond switching in sub-50 nm wurtzite ZMO, highlighting its potential as a low-voltage ferroelectric for integrated nonvolatile memory applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

INR-TEM: Robust cavity detection in multifocus TEM images via implicit neural representations

When characterizing materials using transmission electron microscopy (TEM) images, detecting and quantifying small features in microstructures, such as cavities, pose significant challenges. Off-the-shelf object detection models, including YOLOv8, show considerable performance degradation, particularly when images vary in resolution and the objects of interest possess a low percentage of the total image region of interest. In this study, we introduce a novel detection pipeline that incorporates an implicit neural representation (INR)-based detection method, INR-TEM, and two-modality imaging (e.g., under-focused and over-focused images typically acquired during materials characterization) to improve object detection performance. The INR-TEM method incorporates a pixel-wise prediction principle inspired by pixel-wise centerness weighting. INR-TEM demonstrates superior robustness to resolution variability, maintaining high detection accuracy even at low image resolutions compared to YOLOv8. To leverage INR-TEM effectively in real-world two-modality characterization applications, we further integrate a two-stage motion correction pipeline designed explicitly for aligning multifocus TEM images. The alignment process, comprising keypoint (based on scale-invariant feature transform, SIFT) and intensity matching, significantly mitigates the adverse effects of perceived motion-induced image degradation during through-focal TEM imaging, directly enhancing INR-TEM’s detection capability over conventional single-focus images. Our integrated INR-TEM cavity detection framework notably improves performance across various cavity sizes, outperforming off-the-shelf YOLOv8 detections that rely on a single image modality.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2017

Electron Cyclotron power management for control of Neoclassical Tearing Modes in the ITER baseline scenario

Time-dependent simulations are used to evolve plasma discharges in combination with a Modified Rutherford equation (MRE) for calculation of Neoclassical Tearing Mode (NTM) stability in response to Electron Cyclotron (EC) feedback control in ITER. The main application of this integrated approach is to support the development of control algorithms by analyzing the plasma response with physics-based models and to assess how uncertainties in the detection of the magnetic island and in the EC alignment affect the ability of the ITER EC system to fulfill its purpose. These simulations indicate that it is critical to detect the island as soon as possible, before its size exceeds the EC deposition width, and that maintaining alignment with the rational surface within half of the EC deposition width is needed for stabilization and suppression of the modes, especially in the case of modes with helicity (2,1). A broadening of the deposition profile, for example due to wave scattering by turbulence fluctuations or not well aligned beams, could even be favorable in the case of the (2,1)-NTM, by relaxing an over-focussing of the EC beam and improving the stabilization at the mode onset. Pre-emptive control reduces the power needed for suppression and stabilization in the ITER baseline discharge to a maximum of 5 MW, which should be reserved and available to the Upper Launcher during the entire flattop phase. By assuming continuous triggering of NTMs, with pre-emptive control ITER would be still able to demonstrate a fusion gain of Q=10.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Progress toward Accelogic compression in ROOT

For the last 7 years, Accelogic pioneered and perfected a radically new theory of numerical computing codenamed “Compressive Computing”, which has an extremely profound impact on real-world computer science [1]. At the core of this new theory is the discovery of one of its fundamental theorems which states that, under very general conditions, the vast majority (typically between 70% and 80%) of the bits used in modern large-scale numerical computations are absolutely irrelevant for the accuracy of the end result. This theory of Compressive Computing provides mechanisms able to identify (with high intelligence and surgical accuracy) the number of bits (i.e., the precision) that can be used to represent numbers without affecting the substance of the end results, as they are computed and vary in real time. The bottom-line outcome will be to provide state-of-the-art compression algorithms --and accompanying software libraries-- able to surpass the performance of the compression engines currently available in the ROOT [7] framework. The resulting technology has the capability to enable substantial economic and operational gains (including speedup) for High Energy and Nuclear Physics data storage/analysis. In our initial studies, a factor of nearly x4 (3.9) compression was achieved with RHIC/STAR data where ROOT compression managed only x1.4 [6].As a collaboration of experimental scientists, private industry, and the ROOT Team, our aim is to capitalize on the substantial success delivered by the initial effort and produce a robust technology properly packaged as an open-source tool that could be used by virtually every experiment around the world as means for improving data management and accessibility.In this contribution, we will present our efforts integrating our concepts of “functionally lossless compression” within the ROOT framework implementation, with the purpose of producing a basic solution readily integrated into HENP applications. We will also present our progress applying this compression through realistic examples of analysis from both the STAR and CMS experiments.

Canal, Ph.↗
DOE OSTI2024

Validation of the stochastic inversion algorithm for acoustic travel-time tomography: a large eddy simulation study

Acoustic tomography (AT) is explored as a remote sensing technique to obtain instantaneous snapshots of temperature and velocity fluctuations for wind energy applications. This study integrates Large Eddy Simulation (LES) with the Stochastic Inversion (SI) method to validate the algorithm’s capacity for accurate reconstruction of atmospheric fluctuations. The initial findings demonstrate the efficacy of the method in accurately capturing the predominant flow structures. Normalized L2 error evaluations further inform the algorithm’s precision, with errors accentuated in less sampled peripheral regions. The results underscore the method’s promise as a non-intrusive observational tool, with ongoing development poised to improve its precision and reliability.

17 WIND ENERGY↗
DOE OSTI2017

High-resolution structural characterization and magnetic properties of epitaxial Ce-doped yttrium iron garnet thin films

Thin films of magnetic garnet materials, e.g. yttrium iron garnet (Y 3 Fe 5 O 12 , YIG), are useful for a variety of applications including microwave integrated circuits and spintronics. Moreover, substitution of rare earth ions, such as cerium, is known to enhance the magneto-optic Kerr effect (MOKE) as compared to pure YIG. Thin films of Ce 0.75 Y 2.25 Fe 5 O 12 (Ce:YIG) have been grown using the pulsed laser deposition (PLD) technique and their crystal structure examined using high resolution scanning transmission electron microscopy. Homogeneous substitution of Ce in YIG, without oxidation to form a separate CeO 2 phase, can be realized in a narrow process window with resulting enhancement of the MOKE signal. We investigated the thermally generated signal due to spin Seebeck effect for the optimally doped Ce:YIG films.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Equilibration of quasi-one-dimensional Fermi gases

One-dimensional systems often possess multiple channels or bands arising from the excitation of transverse degrees of freedom. In this work, we study the specific processes that dominate the equilibration of multichannel Fermi gases at low temperatures. Focusing on the case of two channels, we perform an analysis of the relaxation properties of these systems by studying the spectrum and eigenmodes of the linearized collision integral. As an application of this analysis, a detailed calculation of the bulk viscosity is presented. As a result, the dominant scattering processes obey an unexpected conservation law which is likely to affect the hydrodynamic behavior of these systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗