Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Influence of non-magnetic Cu on enhancing the low temperature magnetic properties and Curie temperature of FeCoNiCrCu(x) high entropy alloys

The microstructure and magnetic properties of three face-centered cubic (FCC) FeCoNiCrCu(x) high entropy alloys (HEAs) (x=0, 0.5, 1) are investigated. Interestingly, addition of the nonmagnetic element Cu to FeCoNiCr HEA is found to enhance exchange interactions and low temperature saturation magnetization. The paramagnetic to ferromagnetic Curie transition temperature increases from 85 K for FeCoNiCr to 118 K for FeCoNiCrCu. This is counterintuitive since Cu is nonmagnetic; however, atom probe tomography revealed Cu rich clusters containing 5 at% Ni and 1 at% each of Fe, Co, Cr, within FCC matrix, these clusters altered the matrix composition and consequently its magnetic properties.

Chaudhary, Varun↗
DOE OSTI2026

Microstructural evolution, defect mitigation, and precipitation behavior in AA6061 via laser powder bed fusion with high-temperature substrate heating

Defects, particularly solidification cracking, remain persistent challenges in the laser powder bed fusion (LPBF) processing of AA6061 aluminum alloy. This study systematically investigates defect mitigation, microstructural evolution, and mechanical properties associated with high-temperature substrate preheating at 500 °C. Comprehensive microstructural analyses, including characterization of defects, grain structures, and precipitation behavior, were performed on samples in both as-built and T6 heat-treated states. Elevated preheating substantially reduced solidification cracking across a wide processing window, while demonstrating decreased crack sensitivity to laser parameters. Columnar cracks along the build direction were observed despite substrate preheating. Lack-of-fusion and keyhole porosity were effectively eliminated, though gas-induced microporosity persisted at higher powers. In-depth characterization of two distinct laser power and speed conditions confirmed the formation of micron-sized, non-coherent Mg 2 Si precipitates under heated substrate conditions, alongside α-AlFeCrMnSi intermetallic phases indicative of in-situ thermal effects during fabrication. Subsequent T6 heat treatment revealed the formation of fine, coherent needle-shaped β″ strengthening precipitates. Despite substantial differences in processing parameters, comparable mechanical properties were measured in the as-built samples (∼52 MPa yield strength, ∼130 MPa tensile strength), primarily due to reduced strain hardening effects and consistent precipitation characteristics. Meanwhile, the T6 heat treatment led to significant improvement in properties, enhancing yield strength by over 400%, aligning closely with the performance of conventional wrought AA6061-T6. These findings underscore that high-temperature substrate preheating offers an effective means to suppress cracks, control precipitation, and enhance mechanical performance in LPBF-processed AA6061.

36 MATERIALS SCIENCE↗
DOE OSTI2022

ExaAM: Metal additive manufacturing simulation at the fidelity of the microstructure

Additive manufacturing (AM), or 3D printing, of metals is transforming the fabrication of components, in part by dramatically expanding the design space, allowing optimization of shape and topology. However, although the physical processes involved in AM are similar to those of welding, a field with decades of experimental, modeling, simulation, and characterization experience, qualification of AM parts remains a challenge. The availability of exascale computational systems, particularly when combined with data-driven approaches such as machine learning, enables topology and shape optimization as well as accelerated qualification by providing process-aware, locally accurate microstructure and mechanical property models. We describe the physics components comprising the Exascale Additive Manufacturing simulation environment and report progress using highly resolved melt pool simulations to inform part-scale finite element thermomechanics simulations, drive microstructure evolution, and determine constitutive mechanical property relationships based on those microstructures using polycrystal plasticity. We report on implementation of these components for exascale computing architectures, as well as the multi-stage simulation workflow that provides a unique high-fidelity model of process–structure–property relationships for AM parts. In addition, we discuss verification and validation through collaboration with efforts such as AM-Bench, a set of benchmark test problems under development by a team led by the National Institute of Standards and Technology.

3D printing↗
DOE OSTI2018

Cetyltrimethylammonium Bromide (CTAB) Surfactant-Assisted Synthesis of BiFeO{sub 3} Nanoparticles by Sol-Gel Auto-Combustion Method

In this research, BiFeO{sub 3} nanoparticles were synthesized by sol-gel auto-combustion method with and without the addition of cetyltrimethylammonium bromide (CTAB) surfactant. The effect of different amounts of CTAB addition (0, 1.5, 3, and 6 wt.%) on phase constituents, microstructure, and magnetic properties of the synthesized samples were evaluated using X-ray diffraction (XRD), field emission scanning electron microscope (FESEM), and vibration sample magnetometer (VSM). Also, BiFeO{sub 3} nanoparticles were used for the degradation of methylene blue (MB) as a typical dye pollutant under UV irradiation. XRD results showed the formation of BiFeO{sub 3} mainly with some minute impurity phases such as Bi{sub 2}O{sub 3} and γ-Fe{sub 2}O{sub 3}. Proper amounts of CTAB addition (1.5 wt.%) considerably eliminates Bi{sub 2}O{sub 3} and γ-Fe{sub 2}O{sub 3} residuals in the combustion product. FESEM micrographs show particle size reduction and also more uniform particle size distribution when using 0.75 wt.% of CTAB addition. In the presence of the BiFeO{sub 3}, the UV irradiation for 120 min resulted in 26% degradation of MB, in a sample with 0.75 wt.% CTAB. The synthesized nanoparticles of BiFeO{sub 3} in the sample with 0.75 wt.% CTAB after calcination at 650 {sup ∘}C showed a weak ferromagnetism behavior with saturation magnetization of 0.54 emu/g. {sub i}H{sub C} values of the samples are in the range of 200 to 238 Oe, depending on the crystallite size and phase constituents of the samples.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Heat-treated glassy carbon under pressure exhibiting superior hardness, strength and elasticity

Glassy carbon (GC) is a type of non-graphitizing disordered carbon material at ambient pressure and high temperatures, which has been widely used due to its excellent mechanical properties. Here we report the changes in the microstructure and mechanical properties of GC treated at high pressures (up to 5 GPa) and high temperatures. The formation of intermediate sp 2 –sp 3 phases is identified at moderate treatment temperatures before the complete graphitization of GC, by analyzing synchrotron X-ray diffraction, Raman spectra, and transmission electron microscopy images. The intermediate metastable carbon materials exhibit superior mechanical properties with hardness reaching up to 10 GPa and compressive strength reaching as high as 2.5 GPa, nearly doubling those of raw GC, and improving elasticity and thermal stability. The synthesis pressure used in this study can be achieved in the industry on a commercial scale, enabling the scalable synthesis of this type of strong, hard, and elastic carbon materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of docetaxel on mechanical properties of ovarian cancer cells

Docetaxel could inhibit the proliferation of tumor cells by targeting microtubules. The extension of cellular microtubules plays an important role in the invasion and metastasis of tumor cells. This paper aims to study the distribution and mechanical properties of cytoskeletal proteins with low concentration of docetaxel. MTT assay was used to detect the minimum drug activity concentration of docetaxel on SKOV-3 cells, fluorescence staining was used to analyze the distribution of cytoskeleton proteins, scanning electron microscopy(SEM) was used to observe the morphology of single cells, and atomic force microscopy(AFM) was used to determine the microstructure and mechanical properties of cells. The results showed that the IC{sub 10} of docetaxel was 1 ng/ml. Docetaxel can effectively inhibit the formation of cell pseudopodia, hinder the indirectness between cells, reduce the cell extension area, and make the cells malformed. In addition, when AFM analyzes the effects of drugs on cell microstructure and mechanical properties, the average cell surface roughness and cell height are positively correlated with the concentration of docetaxel. Especially when the concentration was 100 ng/ml, the adhesion decreased by 37.04% and Young's modulus increased by 1.57 times compared with the control group. This may be because docetaxel leads to microtubule remodeling and membrane protein aggregation, which affects cell microstructure and increases cell strength, leading to significant changes in the mechanical properties of ovarian cells. This is of great significance to the study of the formation mechanism of tumor cell invasion and migration activities mediated by actin.

60 APPLIED LIFE SCIENCES↗
NASA NTRS2010

Fatigue Resistance of the Grain Size Transition Zone in a Dual Microstructure Superalloy Disk

Mechanical property requirements vary with location in nickel-based superalloy disks. To maximize the associated mechanical properties, heat treatment methods have been developed for producing tailored microstructures. In this study, a specialized heat treatment method was applied to produce varying grain microstructures from the bore to the rim portions of a powder metallurgy processed nickel-based superalloy disk. The bore of the contoured disk consisted of fine grains to maximize strength and fatigue resistance at lower temperatures. The rim microstructure of the disk consisted of coarse grains for maximum resistance to creep and dwell crack growth at high temperatures up to 704 C. However, the fatigue resistance of the grain size transition zone was unclear, and needed to be evaluated. This zone was located as a band in the disk web between the bore and rim. Specimens were extracted parallel and transverse to the transition zone, and multiple fatigue tests were performed at 427 and 704 C. Mean fatigue lives were lower at 427 C than for 704 C. Specimen failures often initiated at relatively large grains, which failed on crystallographic facets. Grain size distributions were characterized in the specimens, and related to the grains initiating failures as well as location within the transition zone. Fatigue life decreased with increasing maximum grain size. Correspondingly, mean fatigue resistance of the transition zone was slightly higher than that of the rim, but lower than that of the bore. The scatter in limited tests of replicates was comparable for all transition zone locations examined.

Gabb, T. P.↗
NASA NTRS1991

Processing and properties of SiC whisker- and particulate-reinforced reaction bonded Si3N4

The microstructure and mechanical properties of reaction bonded Si3N4 (RBSN) reinforced with SiC whiskers of particles were investigated using RBSN composites made from colloidally pressed octanol dispersions of high-purity Si powders mixed with either SiC whiskers or alpha-SiC particles. Results of investigations, revealing high conversions of Si to Si3N4, specific surface areas, and constant relative densities and strengths, showed that the uniform microstructure and small flaw size of the matrix were maintained in the composites and that no degradation of the reinforcements was taking place. Neither the monolithic nor the composite materials exhibited R-curve behavior. A modest increase in fracture toughness was observed only in the RBSN containing 33 vol pct SiC(p).

Lightfoot, A.↗
DOE OSTI2018

Phase-control synthesis and catalytic property of magnetic Ni@NixPy core-shell microstructures

Highlights: • Ni@Ni{sub x}P{sub y} core-shell microstructures are synthesized by a low-temperature phosphidation route. • The initial Ni/NaH{sub 2}PO{sub 2} molar ratio can strongly affect the phase of the final product. • Ni@Ni{sub x}P{sub y} microstructures present good catalytic activity for the reduction of 4-nitrophenol. • The catalytic property of Ni@Ni{sub x}P{sub y} microstructures presents markedly phase-dependent features. - Abstract: Magnetic Ni@Ni{sub x}P{sub y} core-shell microstructures were successfully synthesized by a simple low-temperature phosphidation route, employing Ni nanospheres as the initial nickel source, NaH{sub 2}PO{sub 2}·H{sub 2}O as the phosphorus ion source. The phosphidation reaction was carried out in N{sub 2} atmosphere at 300 °C for 2 h. Experiments showed that the initial Ni/NaH{sub 2}PO{sub 2} molar ratio could strongly affect the phase of the final product. When the Ni/NaH{sub 2}PO{sub 2} molar ratio of 1:2.77 was used, hexagonal Ni{sub 2}P phase was obtained; while the Ni/NaH{sub 2}PO{sub 2} molar ratio was 1:5.54, hexagonal Ni{sub 5}P{sub 4} phase was produced. It was found that the magnetic properties of the products gradually decreased with the conversion from Ni nanospheres, to Ni@Ni{sub 2}P and to Ni@Ni{sub 5}P{sub 4}. Moreover, initial Ni nanospheres, Ni@Ni{sub 2}P and Ni@Ni{sub 5}P{sub 4} core-shell microstructures presented outstanding catalytic activities for the reduction of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP) in excess NaBH{sub 4} solution. Ni@Ni{sub 5}P{sub 4} core-shell microstructures owned the best catalytic activity.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

A laser ultrasonics-based approach for rapid screening of high entropy alloys

This project demonstrates a laser ultrasonics-based characterization methodology for rapid metallic materials design and discovery via in situ determination of phases, microstructures and elastic properties with respect to temperature. Ultrasonic waves are strongly affected by material microstructure, and therefore serve as a facile means to probe elastic properties, phase content and their size distributions and volume fractions. In this study, a laser ultrasonic technique is used to systematically study the evolution of properties in a set of interrelated simple binary alloys and high entropy alloys (HEA). Phase transformations and microstructural changes inferred from the ultrasonic signals will be correlated with electron microscopy data and predictions using calculations of phase diagrams (CALPHAD). The non-contact and non-destructive ultrasonic testing approach developed in this study could overcome several limitations associated with current material characterization methods for materials discovery. It is expected that laser ultrasonics-based methodology developed in this work will be utilized to evaluate novel graded composition HEAs currently being developed at the Idaho National Laboratory (INL) using advanced manufacturing methods based on direct energy deposition and spark plasma sintering processes, and contribute to accelerate the discovery of HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A laser ultrasonics-based approach for rapid screening of high entropy alloys

The primary objective of this seed project is to develop a laser ultrasonics-based characterization methodology for rapid metallic materials design and discovery via in situ determination of phases, microstructures and elastic properties with respect to temperature. Ultrasonic waves are strongly affected by material microstructure, and therefore, serve as a facile means to probe elastic properties, phase content and their size distributions and volume fractions. In this study, a laser ultrasonic technique will be used to systematically study the evolution of properties in a set of interrelated simple binary alloys and high entropy alloys (HEA). Phase transformations and microstructural changes inferred from the ultrasonic signals will be correlated with electron microscopy data and predictions using calculations of phase diagrams (CALPHAD). The non-contact and non-destructive ultrasonic testing approach developed in this study could overcome several limitations associated with current material characterization methods for materials discovery. It is expected that the products of the proposed work will be utilized to evaluate novel graded composition HEAs currently being developed at the Idaho National Laboratory (INL) using advanced manufacturing methods based on direct energy deposition and spark plasma sintering processes, and contribute to accelerate the discovery of HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Failure Analysis and Magnetic Evaluation of Tertiary Superheater Tube Used in Gas-Fired Boiler

Failure analysis was carried out on a prematurely failed tertiary superheater tube used in gas-fired boiler. The analysis includes a comparative study of visual examination, chemical composition, hardness and microstructure at failed region, adjacent and far to failure as well as on fresh tube. The chemistry was found matching to the standard specification, whereas the hardness was low in failed tube compared to the fish mouth opening region and the fresh tube. Microscopic examination of failed sample revealed the presence of spheroidal carbides of Cr and Mo predominantly along the grain boundaries. The primary cause of failure is found to be localized heating. Magnetic hysteresis loop (MHL) measurements were carried out to correlate the magnetic parameters with microstructure and mechanical properties to establish a possible non-destructive evaluation (NDE) for health monitoring of the tubes. The coercivity of the MHL showed a very good correlation with microstructure and mechanical properties deterioration enabling a possible NDE technique for the health monitoring of the tubes.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Harnessing structural stochasticity in the computational discovery and design of microstructures

This paper presents a deep generative model-based design methodology for tailoring the structural stochasticity of microstructures. Although numerous methods have been established for designing deterministic (periodic) or stochastic microstructures, a systematic design approach that allows the unified treatment of both deterministic and stochastic microstructure design domains has yet to be created. The proposed methodology resolves this issue by learning a unified feature space that embodies diverse structural patterns with continuously varying stochasticity levels. A highly diverse microstructure database is established to incorporate various types of deterministic and stochastic microstructure patterns. A property-aware deep generative model is proposed to learn a unified feature space of the structural characteristics, as well as the relationship between structure features and properties of interest. Autoencoder (AE), Variational Autoencoder (VAE), and Adversarial Autoencoder (AAE) are compared to understand their relative merits in the property-aware learning of the unified feature space. Microstructural designs with tailorable stochasticity and properties are obtained by searching the unified feature space. Multiple design cases are presented to demonstrate the capability of designing microstructures for structural stochasticity and properties. Furthermore, the proposed method is employed to create stochastically graded structures, which manipulate the mechanical behaviors by varying the local stochasticity of the structure.

36 MATERIALS SCIENCE↗
NASA NTRS2002

Reactive Processing of Environment Conscious, Biomorphic Ceramics: A Novel and Eco-friendly Route to Advanced Ceramic

Environment-conscious, biomorphic ceramics (Ecoceramics) are a new class of materials that can be produced with renewable resources (wood) and wood wastes (wood sawdust). These materials have tailorable properties with numerous potential applications. Silicon carbide-based ecoceramics have been fabricated by the infiltration of wood-derived carbonaceous preforms with oxide and silicon based materials. The wood-derived carbonaceous preforms have been shown to be quite useful in producing porous or dense materials with different microstructures and compositions. The microstructure and mechanical properties (flexural strength, fracture toughness, elastic modulus, and compressive strength) of a wide variety of Sic-based ecoceramics have been measured. Ecoceramics have tailorable properties and behave like ceramic materials manufactured by conventional approaches. In this presentation the fabrication approach, microstructure, and thermomechanical properties of a wide variety of Sic-based Ecoceramics will be reported.

Singh, M.↗
DOE OSTI2018

A micro-mechanism to explain the post-DRX grain growth at temperatures > 0.8Tm

Highlights: • Austenitic grain growth during working at temperature > 0.8T{sub m} is reduced by > 50%. • Growth mechanism during loading is distinct from growth in absence of loading. • During loading, growth occurs due to alignment of slip planes and grain merging. • Interruption of loading causes competitive growth and limits grain size. • Interrupted loading results in optimal microstructural and mechanical properties. - Abstract: A micro-mechanism responsible for the occurrence of post-dynamic recrystallization (DRX) grain growth during deformation at T > 0.8T{sub m} is described. Thermo-mechanical testing, microstructural characterization and diffraction studies reveal the link between slip and grain growth. If deformation is imparted in a single stage, grains grow by a cooperative growth process involving grain rotation and alignment of slip planes. This mechanism changes when deformation is interrupted and controlled intermediate soaking is performed before re-loading. A premeditated control of mechanism is shown to yield favourable microstructural and mechanical properties. A strategy to apply this control to industrial hot deformation is outlined.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Carburization and decarburization behavior of Grade 91 ferritic-martensitic steel in liquid sodium environments

Here, this paper presents a study of carbon transfer and its effect on microstructure and tensile properties of Grade 91 (G91) ferritic-martensitic steel exposed to sodium at 550–650 °C. Sodium exposure tests were conducted in Argonne's forced convection sodium loops up to exposure times of ~40,000 h. Thermal aging study of G91 steel was conducted in parallel to isolate the thermal aging effect from the sodium effect. It was found that sodium exposures at 650 °C dissolved M 23 C 6 carbides, eliminated the martensite subgrain structure resulting in excessive grain growth and reduced the tensile strength by >50%, while sodium exposures at 550 and 600 °C had an insignificant effect on its microstructure and tensile properties. These effects were attributed to the carburization/decarburization process of G91 steel in sodium environments. Carbon concentrations in sodium were determined by a foil equilibration method. The estimated carbon concentration was in the range of 0.8–1.2 ppm in the SMT-1 loop and 0.3–0.7 ppm in the SMT-2 loop. Thermodynamic analysis of the carburization – decarburization process was conducted for G91 steels exposed in sodium environments. The carbon activity-concentration relationship for G91 was evaluated by considering four phases in G91, i.e. bcc ferrite, M 23 C 6 , NbC and VC carbides. It was found that the carburization-decarburization process in G91 steel was dictated by M 23 C 6 carbides at high carbon activities, while NbC and VC carbides dominated the process at low carbon activities. The calculated carburization-decarburization boundary showed that G91 would undergo decarburization at 650 °C and carburization at 550 °C in the sodium loop environments, which was consistent with our experimental observations. This experimental and theoretical analysis provided a basis for predicting the effect of carbon transfer on the integrity of reactor components in sodium environments and for the design of new alloys used in sodium-cooled fast reactors.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

A Comparison of Microstructure and Mechanical Performance of Inconel 718 Manufactured via L-PBF, LP-DED, and WAAM Technologies

The microstructure and mechanical properties of additively manufactured (AM) alloys can be significantly affected by variations in cooling rates, resulting from different process conditions across different additive manufacturing (AM) platforms. Therefore, it is crucial to understand the effect of manufacturing process on the microstructure and mechanical properties of AM Inconel 718. This study examines three AM processes: laser powder bed fusion, laser powder directed energy deposition, and wire arc additive manufacturing. Results show that fully heat treated laser powder bed fused (L-PBF) and wire arc additively manufactured (WAAM) Inconel 718 specimens exhibit higher strength compared to laser powder directed energy deposited (LP-DED) ones due to finer grain structure in L-PBF and retained dendritic microstructure in WAAM. The ductility in LP-DED Inconel 718 was slightly higher compared to WAAM and L-PBF due to relatively small carbide size, which causes stress concentration in a small material volume, leading to delayed fracture.

Additive manufacturing (AM)↗