Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Process-Defect-Structure-Property Correlations During Laser Powder Bed Fusion of Alloy 718: Role of In Situ and Ex Situ Characterizations

Components made by laser powder bed fusion (L-PBF) additive processes require extensive trial and error optimization to minimize defects and arrive at targeted microstructure and properties. In this paper, in situ infrared thermography and ex situ surface roughness measurements were explored as methodologies to ensure Inconel ® 718-part quality. For a given laser energy of 200 Watts, prismatic samples were produced with different exposure times (80 to 110 µs) and point spacings (80 to 110 µm). The infrared intensities from laser–material interaction zones were measured spatially and temporally. The conditions leading to higher IR intensity and lowest surface roughness values correlated well with less porosity and coarse solidification grain structure. The transition from highly columnar to misoriented growth is attributed to changes in thermal gradients and liquid–solid interface velocities. Hardness measurements and electron microscopy of the as-processed and post-processed heat-treated samples show complex transitions in microstructural states including the heavily dislocated FCC matrix, reduction of dislocation density, and copious precipitation, respectively. These results show that the geometry-process-structure-property correlations are dynamic, and they cascade depending on the transitions of phase states from powder to liquid to solid, as well as phase decompositions and deformations within the solid FCC phase. Finally, validity of using analytical weld process models to describe the above phenomena is also highlighted.

36 MATERIALS SCIENCE↗

Low and room temperatures tensile properties of a nanoprecipitate-strengthened (FeCoCr)40Ni40Al10Cu10 high-entropy alloy

Highlights: • We designed a (FeCoCr){sub 40}Ni{sub 40}Al{sub 10}Cu{sub 10} high entropy alloy (HEA) strengthened by exclusive L1{sub 2} nano-precipitates. • The present HEA exhibited excellent combination of tensile strength (~1200MPa) and elongation (~36%) at 233 K. • The coherent nano-precipitates, deformation twinning and immobile LC locks made a joint contribution to the optimal mechanical property. - Abstract: We report the tensile properties and microstructural evolution of a high entropy alloy (FeCoCr){sub 40}Ni{sub 40}Al{sub 10}Cu{sub 10} deformed at low temperature (233K) and room temperature (293 K). The alloy presented a superior combination of tensile strength (~1200 MPa) and elongation (~36%) at 233 K than at 293 K. Transmission electron microscopy revealed that the enhanced tensile properties at low temperature were due to deformation twinning, the formation of immobile Lomer-Cottrell dislocation locks, and the high density coherent nano-precipitates.

36 MATERIALS SCIENCE↗

Nanoscale Reinforced, Polymer Derived Ceramic Matrix Coatings

The goal of this project was to explore and develop a novel class of nanoscale reinforced ceramic coatings for high temperature (600-1000 C) corrosion protection of metallic components in a coal-fired environment. It was focused on developing coatings that are easy to process and low cost. The approach was to use high-yield preceramic polymers loaded with nano-size fillers. The complex interplay of the particles in the polymer, their role in controlling shrinkage and phase evolution during thermal treatment, resulting densification and microstructural evolution, mechanical properties and effectiveness as corrosion protection coatings were investigated. Fe-and Ni-based alloys currently used in coal-fired environments do not possess the requisite corrosion and oxidation resistance for next generation of advanced power systems. One example of this is the power plants that use ultra supercritical steam as the working fluid. The increase in thermal efficiency of the plant and decrease in pollutant emissions are only possible by changing the properties of steam from supercritical to ultra supercritical. However, the conditions, 650 C and 34.5 MPa, are too severe and result in higher rate of corrosion due to higher metal temperatures. Coating the metallic components with ceramics that are resistant to corrosion, oxidation and erosion, is an economical and immediate solution to this problem. Good high temperature corrosion protection ceramic coatings for metallic structures must have a set of properties that are difficult to achieve using established processing techniques. The required properties include ease of coating complex shapes, low processing temperatures, thermal expansion match with metallic structures and good mechanical and chemical properties. Nanoscale reinforced composite coatings in which the matrix is derived from preceramic polymers have the potential to meet these requirements. The research was focused on developing suitable material systems and processing techniques for these coatings. In addition, we investigated the effect of microstructure on the mechanical properties and oxidation protection ability of the coatings. Coatings were developed to provide oxidation protection to both ferritic and austentic alloys and Ni-based alloys. The coatings that we developed are based on low viscosity pre-ceramic polymers. Thus they can be easily applied to any shape by using a variety of techniques including dip-coating, spray-coating and painting. The polymers are loaded with a variety of nanoparticles. The nanoparticles have two primary roles: control of the final composition and phases (and hence the properties); and control of the shrinkage during thermal decomposition of the polymer. Thus the selection of the nanoparticles was the most critical aspect of this project. Based on the results of the processing studies, the performance of selected coatings in oxidizing conditions (both static and cyclic) was investigated.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Hot rolling of ZK60 magnesium sheet with isotropic tensile properties from tubing made by Shear Assisted Processing and Extrusion (ShAPE)

In order to evaluate the viability of ShAPE processed Mg alloys as a feedstock for fabricating lightweight sheet material, tubes consisting of ShAPE-extruded Mg alloy ZK60 were flattened into plates and hot rolled at 450 °C to reductions of 37%, 68%, and 93%. The mechanical properties and microstructure of the rolled material were characterized through tensile testing and electron backscattered diffraction (EBSD). ZK60 specimens rolled to 68% reduction had tensile properties similar to published properties of rolled ZK60 sheets fabricated using conventional processes, and exhibited negligible tensile anisotropy referenced to the rolling direction. Additional rolling from 68% to 93% reduced the ultimate tensile stress in the rolling direction from 341.74±5.96 MPa to 260.76±22.4MPa. The yield stress and elongation to failure of the material also decreased from 292.16±1.11 MPa to 256.93±18.4 MPa and 6.95±1.94% to 3.38±0.51%, respectively, but negligible little anisotropy was observed with respect to loading direction. EBSD mapping indicated that the as-extruded ZK60 had texture rotated away from the basal direction which developed into a strong basal texture over numerous hot rolling steps. This evolution in texture has been observed after rolling for hot-rolled ZK60 fabricated through conventional extrusion processes. The initial grain structure was found to have experienced noticeable twinning from flattening the tube into plate. After hot rolling, the grain structure became more equiaxed, but the average grain diameter did not change appreciably from 5.15 ± 3.39 µm in the ShAPE extruded material, to 5.27 ± 12.44 µm in the 93% hot rolled sheet. This response to hot rolling is similar to the response of ZK60 fabricated using other methods such as Equal Channel Angular Processing (ECAP). Therefore, this work demonstrates ShAPE has the potential as an alternative method to producing feedstock for Mg alloy sheets. Modifications to the experimental procedure which could lead to improvements in observed properties are briefly discussed.

36 MATERIALS SCIENCE↗

Annular Metallic Nuclear Fuel Informatics at 50 nm Resolution

U-10wt.% Zr (U-10Zr) based metallic fuel is the leading candidate for next-generation sodium cooled fast reactor in United States. Advanced post-irradiation characterization (from sub-nanometer to micrometer) helps to understand fuel microstructure and property change during irradiation, benefiting fuel qualification for commercial application. With high velocity image data generating method, an automatic way to extract the microstructural information quantitively can better serve the needs from post irradiation characterization. A trained machine learning model, named Decision Tree, is employed to categorize pores caused by fission gas release and to aid phase identification. This work presents a showcase of this approach on different irradiated U-10Zr metallic fuels. This quantitative data offers insights into the fission product migration and potentially thermal conductivity degradation. This information from machine learning will be fed into fuel design code for better prediction of fuel performance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A detailed study of the microstructure and thermal stability of typical SiC fibers

Highlights: • The cross-sectional microstructure and thermal stability of typical SiC fibers were characterized via SEM and TEM. • The SiC fiber with gradient microstructure has better properties than that with uniform microstructure. • The graphite exhibits straight planes on the fiber surface while they're turbostratic inside the fiber. Continuous SiC fibers have attracted increasing research interest for their significant application in aerospace and nuclear energy. Control of inhomogeneity and decrement of defects are crucial for improving the mechanical and high-temperature performance of SiC fibers. Thus an understanding of fine and detailed microstructural and microchemical distribution of SiC fibers is urgently needed. In the present work, the cross-sectional phase distributions, morphologies and defects of amorphous, non-stoichiometric and near-stoichiometric SiC fibers were well characterized. From surface to core, the amorphous and non-stoichiometric fibers exhibited uniform microstructures, but a gradient change along the radial direction was observed in the near-stoichiometric fiber. Nanosized SiC and turbostratic carbon (2–4 nm) were randomly distributed inside the amorphous fiber. A large amount of graphite surrounding SiC grains appears in the non-stoichiometric fiber which possess low strength and weak thermal stability. The near-stoichiometric fiber has transgranular fracturing, high strength and favorable thermal stability, and the graphite planes are turbostratic inside the fiber but straight on the surface. The results of both energy-dispersive X-ray spectrometry measurements and first-principles calculations demonstrate that Al atoms can occupy Si sites in the SiC grains. Our findings offer fine understanding for fabricating SiC fibers with superior properties.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Model-informed, Adaptive Physical Vapor Deposition to Fabricate Hierarchical Binary-alloy Thin-films

Designing next generation thin films, tailor-made for specific applications, relies on the availability of robust processing-structure-property relationships. Traditional structure zone diagrams are limited to low-dimensional mappings, with machine-learning methods only recently attempting to relate multiple processing parameters to the final microstructure. Despite this progress, structure-processing relationships are unknown for processing conditions that vary during thin-film deposition, limiting the range of microstructures and properties achievable. In this project, we employed a phase-field computational model combined with a genetic algorithm (GA) to identify and design time-dependent processing protocols that achieve tailor-made microstructures. We simulate the physical vapor deposition of a binary-alloy thin film by employing a phase-field model, where deposition rates and diffusivities are controlled via the genetic algorithm. Our GA-guided protocols achieve targeted microstructures with lateral and vertical concentration modulations, as well as more complex, hierarchical microstructures previously not described in simple structure zone diagrams. Our algorithm provides insight to experimentalists looking for additional avenues to design novel thin-film microstructures.

36 MATERIALS SCIENCE↗

Characterization of hot-pressed von Alpen type NASICON ceramic electrolytes

The Na-ion conducting solid electrolyte NASICON is a promising solid state electrolyte (SSE) for use in Na based electrochemical systems. The effects of particle morphology and synthesis of von Alpen type NASICON via hot-pressing were investigated. Spray dried particles were shown to improve mechanical and electrochemical properties. X-ray diffraction, scanning electron microscopy, impulse excitation measurements, Vickers hardness, and impedance spectroscopy were used to correlate relationships between phase purity, microstructure, mechanical properties, and electrochemical properties. Scanning electron microscopy showed the presence of a glass phase as between 19.08% and 28.23% area percentage and a ZrO 2 phase between 0.46% and 3.51% area percentage in the hot-pressed samples. Impulse excitation showed elastic modulus varying from 83.65 to 97.65 GPa. The first values of Poisson's ratio and shear modulus of NASICON are reported as between 0.23 and 0.26 and 33.87 to 38.79 GPa, respectively. Vickers hardness and fracture toughness measurements showed Vickers hardness ranging from 4.30 to 4.68 GPa and fracture toughness ranging from 1.05 to 1.09 MPa m ½ . Impedance spectroscopy showed grain conductivities ranging from 1.023 to 1.287 mS/cm, with grain boundary resistance percentages between 73.22 and 47.5%. Total conductivities ranged from 0.292 to 0.596 mS/cm, with 0.596 mS/cm being achieved at room temperature for the spray dried powders with lower grain boundary resistance percentages.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of Ag additions on the lengthening rate of Ω plates and formation of σ phase in Al-Cu-Mg alloys during thermal exposure

Effect of Ag additions on the mechanical properties and microstructures of the peak-aged Al-Cu-Mg alloys during prolonged thermal exposure at 150 °C, was investigated by tensile testing, conventional transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM). The results showed that after exposure for 500 h, > 85% of the peak strength remained. Microstructure observations indicated that increasing the Ag content from 0.14 to 0.57% promoted the precipitation of a fine and uniform Ω phase and suppressed the formation of the θ′ phase, leading to a notable improvement of the strength properties and thermal stability of the studied alloys. Quantitative TEM analysis showed that the coarsening of Ω phase was predominated by plate lengthening rather than thickening, while its lengthening rate was independent of various Ag additions during exposure at 150 °C. In addition, an increase of Ag also facilitated the formation of a cubic σ phase, which was further supported by STEM results. - Highlights: •Increasing Ag improved strength properties and thermal stability of the alloys. •After exposure for 500 h, > 85% of the peak strength remained. •The lengthening rate of Ω plates remained constant as Ag increased at 150 °C. •Increasing Ag content facilitated the formation of σ phase.

36 MATERIALS SCIENCE↗

Effect of 4 wt.% Cr on microstructure, corrosion resistance and tribological properties of Fe{sub 3}Al–20 wt.%Al{sub 2}O{sub 3} composites

Fe{sub 3}Al–20 wt.%Al{sub 2}O{sub 3} ultrafine grained composites with 4 wt.% Cr were prepared by mechanical alloying inducing self propagating high temperature synthesis with subsequent plasma activated sintering. Microstructures of the composites were studied by X-ray diffraction, scanning electron microscopy, energy dispersive spectrum and transmission electron microscope. Then the relative density, room temperature hardness, static corrosion resistance and dry sliding wear behavior at a temperature range of 25 °C–800 °C of the sintered samples were tested and analyzed. The results showed that the composites had high hardness and a good microstructure with fine grain size, high relative density. The composites with 4 wt.% Cr amount also exhibited excellent comprehensive tribological properties at medium–high temperatures especially at a temperature above 500 °C, although the wear resistance did not be improved at 25 °C–500 °C. 4 wt.% Cr element addition improved the corrosion resistance of the composites significantly with the corrosion loss decreasing by 19.48%. - Highlights: ► In-situ Fe{sub 3}Al–20 wt.%Al{sub 2}O{sub 3} composites with 4 wt.% Cr was prepared by MA-PAS. ► Composites had good tribological properties at the temperature above 500 °C. ► Corrosion resistance was improved obviously by 4 wt.% Cr amount.

36 MATERIALS SCIENCE↗

Microstructure, electrical resistivity, and tensile properties of neutron-irradiated Cu–Cr–Nb–Zr

High strength, high conductivity copper alloys that can resist creep at high temperatures are one of the primary candidates for efficient heat exchangers in fusion reactors. Cu–Cr–Nb–Zr (CCNZ) alloys, which were designed to improve the strength and creep life of ITER Cu–Cr–Zr (CCZ) reference alloys, have been found to have comparable electrical conductivity and tensile properties to CCZ alloys. The measured creep rupture times for these improved alloys is about ten times higher than the ITER reference alloys at 90–125 MPa at 500 °C. However, the effects of neutron irradiation on these alloys, and the ensuing material properties, have not been studied; thus, their utility in a fusion reactor environment is not well understood. This study characterizes the room temperature mechanical and electrical properties of a neutron-irradiated CCNZ alloy and compares them to a neutron-irradiated ITER reference heat sink CCZ alloy. Tensile specimens were neutron irradiated in the High Flux Isotope Reactor (HFIR) to 5 dpa between 250 °C and 325 °C. Post-irradiation characterization included electrical resistivity measurements, hardness, and tensile tests. Microstructural evaluation used scanning electron microscopy, energy dispersive x-ray spectroscopy, and atom probe tomography to characterize the irradiation-produced changes in the microstructure and investigate the mechanistic processes leading to post-irradiation properties. Transmutation calculations were validated with composition measurements from atom probe data and used to calculate contributions to the increased electrical resistivity measured after irradiation. Comparisons with CCZ alloys in the same irradiation heat found that the post-irradiated CCNZ and CCZ alloys had comparable electrical resistivity. Although CCNZ alloys suffered more irradiation hardening than CCZ, the overall tensile behavior deviated very little from non-irradiated values in the temperature range studied.

36 MATERIALS SCIENCE↗

Creating bulk nanocrystalline metal.

Nanocrystalline and nanostructured materials offer unique microstructure-dependent properties that are superior to coarse-grained materials. These materials have been shown to have very high hardness, strength, and wear resistance. However, most current methods of producing nanostructured materials in weapons-relevant materials create powdered metal that must be consolidated into bulk form to be useful. Conventional consolidation methods are not appropriate due to the need to maintain the nanocrystalline structure. This research investigated new ways of creating nanocrystalline material, new methods of consolidating nanocrystalline material, and an analysis of these different methods of creation and consolidation to evaluate their applicability to mesoscale weapons applications where part features are often under 100 {micro}m wide and the material's microstructure must be very small to give homogeneous properties across the feature.

36 MATERIALS SCIENCE↗

Influence of microstructure and temperature on impact toughness of H13 steel produced by binder jet additive manufacturing

Binder Jet Additive Manufacturing (BJAM) is a promising manufacturing pathway to produce H13 steel dies and tooling with complex geometries for applications in high pressure aluminum die casting, hot stamping, and injection molding. While fully dense H13 coupons produced using BJAM have been subjected to detailed microstructure characterization, properties which are critical and relevant to the aforementioned applications, such as impact toughness, have not been reported. Here, this work evaluated the influence of microstructural characteristics and test temperature on the impact toughness of H13 produced by BJAM. Coupons were produced from three different powder size distributions (PSDs), with nominal powder size ranges of −22 μm, 10-32 μm, and 15-53 μm. Coupons were printed, sintered, hot isostatically pressed (HIPed), and heat treated by quenching and tempering. After HIPing, the measured porosities of the different PSDs were all less than 0.015 vol%. The −22 μm PSD BJAM material exhibited the best impact toughness of all three PSDs across the entire test temperature range from 25 to 400 °C, and also exhibited an ambient temperature impact toughness of 10.9 J at a hardness of 46 HRC, equivalent to minimum threshold requirements for premium grade H13. However, all three BJAM PSDs exhibited moderately lower impact toughness than premium grade wrought H13 from RT to 400 °C. We attribute this in part due to the very large prior-austenite grain (PAG) sizes near 400 μm and segregation from former liquid channels leading to greater amounts of carbide precipitation on PAG boundaries. Technical pathways for optimizing processing and chemistry of BJAM H13 to further improve impact toughness are discussed.

Binder jet additive manufacturing↗

Influence of Boron on Austenite to Ferrite Transformation Behavior of Low Carbon Steel Under Continuous Cooling

In the current work, the influence of boron on austenite to ferrite transformation behavior under continuous cooling condition and its associated features, e.g., final microstructure, mechanical properties, etc., in low carbon steel has been studied. The steels (C 0.04 wt.%, B 10-100 ppm) prepared in an open air laboratory furnace showed identical microstructures having ferrite grains of 20-25 µm. However, tensile test data indicate variation of yield strength and ultimate tensile strength with boron content. The yield point elongation and strain aging index both were found to decrease with increase in boron content or boron-to-nitrogen ratio. As the boron nitride precipitates stimulate the nucleation of ferrite phase, the dilation curves show an increase in austenite to ferrite transformation start temperature with boron content. The resulting microstructure and hardness value also corroborate the finding. Transmission electron microscopy findings revealed the presence of ultra-fine boron nitride (BN) precipitates in both grain boundary and grain body of the steel having boron concentration of 30 ppm and beyond. The presence of these precipitates also increased with boron content. Based on austenite decomposition behavior, related microstructure and hardness values it is conjectured that these BN precipitates may act as nucleating agent for polygonal ferrite during austenite decomposition, thereby softening the steel during fast cooling.

36 MATERIALS SCIENCE↗

Thermal property and assessment of biocompatibility of poly(lactic-co-glycolic) acid/graphene nanocomposites

Polymer-matrix nanocomposites based on Poly(lactic-co-glycolic) acid (PLGA) and Graphene platelets (GNPs) were studied. GNPs, nanomaterials with a 2D flat surface, were chosen with or without chemical modification in PLGA/GNP nanocomposites and their microstructure, thermal property, and their compatibility as scaffolds for cell growth were investigated. PLGA/GNP nanocomposites (0, 1, and 5 wt. % of GNPs) were prepared using a solution based technique. Transmission electron microscopy, X-ray diffraction, Differential scanning calorimeter, and Thermogravimetric analyzer were used to analyze morphology and thermal properties. This work demonstrated the role of GNPs flat surface to provide a favorable platform resulting in an enhanced PLGA crystallization. Functionalized GNPs suppress both the thermal stability and the crystallization of PLGA. Finally, to determine the potential usefulness of these scaffolds for biomedical applications, mammalian cells were cultured on various PLGA/GNP nanocomposites (0, 1, and 5 wt. % GNPs). 1 wt. % PLGA/GNP nanocomposites showed better biocompatibility for cell growth with/without graphenes functionalization compared to pure PLGA and 5 wt. % PLGA/GNP. The function of GNPs in PLGA/GNPs (1 wt. %) composites is to provide a stage for PLGA crystallization where cell growth is favored. These results provide strong evidence for a new class of materials that could be important for biomedical applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Laser Powder Deposition Parametric Optimization and Property Development for Ti-6Al-4V Alloy

In this study, Ti6Al4V alloy was produced via laser powder deposition (LPD). To obtain Ti6Al4V alloy with maximum density, LPD parameters for preparing Ti6Al4V samples were optimized using the Taguchi method. Results were analyzed on the basis of the signal-to-noise (S/N) ratios and analyses of variance. A high energy density should be used to achieve higher levels of densification. The optimal combination of parameters for density was a scanning speed of 550 mm/min, laser power of 160 W, powder feeding rate of 0.99 g/min, and shield gas flow of 8 L/min. An almost fully dense Ti6Al4V sample was prepared using the optimized LPD process, and the relative density was greater than 99%. In addition, the microstructure and properties of Ti6Al4V samples prepared by optimized LPD process were investigated. The microstructure investigation revealed that the LPD-prepared Ti6Al4V sample was predominantly composed of fine acicular α phase and lath-type α phase. Tensile and microhardness tests indicated that the LPD sample had higher mechanical properties than the traditional cast Ti6Al4V alloy because of the acicular martensitic phase and smaller grain size.

36 MATERIALS SCIENCE↗

Atomistic to continuum modeling of solidification microstructures

We summarize recent advances in modeling of solidification microstructures using computational methods that bridge atomistic to continuum scales. We first discuss progress in atomistic modeling of equilibrium and non-equilibrium solid–liquid interface properties influencing microstructure formation, as well as interface coalescence phenomena influencing the late stages of solidification. The latter is relevant in the context of hot tearing reviewed in the article by M. Rappaz in this issue. We then discuss progress to model microstructures on a continuum scale using phase-field methods. We focus on selected examples in which modeling of 3D cellular and dendritic microstructures has been directly linked to experimental observations. Finally, we discuss a recently introduced coarse-grained dendritic needle network approach to simulate the formation of well-developed dendritic microstructures. The approach reliably bridges the well-separated scales traditionally simulated by phase-field and grain structure models, hence opening new avenues for quantitative modeling of complex intra- and inter-grain dynamical interactions on a grain scale.

36 MATERIALS SCIENCE↗

High Temperature Oxidation Behavior of HVOF-sprayed Coatings for Use in Thixoextrusion Processes

The dies used for the thixoextrusion of steels have to be capable of withstanding complex thermal and mechanical loads, while giving a sufficient wear resistance against abrasion and adhesion at very high temperatures. In order to improve the wear resistance and reduce the heating of the extrusion die it can be protected with a hard cermet coating. The purpose of this work is to study the high-temperature performance of CrC-CoNiCrAlY coating and explore the potential application of this coating to improve dies used in thixoextrusion processes. A two-layer 75CrC-25CoNiCrAlY coating with a CoNiCrAlY bond-coating was fabricated by the HVOF thermal spray process on a steel substrate. Coatings were heat-treated at a range of temperatures between 900 deg. C and 1100 deg. C. The microstructural characterization of the coatings before and after heat treatment was conducted by scanning electron microscopy (SEM) and an X-ray diffractometer (XRD). The mechanical properties of coatings were determined as a function of the temperature of heat treatment. The bond coat effect on the thermal shock resistance of CrC-CoNiCrAlY coating was analyzed.

36 MATERIALS SCIENCE↗