Search NASA⌕ Search

SEARCH · Search NASA

Results for “high modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,387 records · Page 77

Effects of High-Temperature Annealing in Air on Hi-Nicalon Fiber-Reinforced Celsian Matrix Composites

BN/SiC-coated Hi-Nicalon fiber-reinforced celsian matrix composites (CMC) were annealed for 100 h in air at various temperatures to 1200 C, followed by flexural strength measurements at room temperature. Values of yield stress and strain, ultimate strength, and composite modulus remain almost unchanged for samples annealed up to 1100 C. A thin porous layer formed on the surface of the 1100 C annealed sample and its density decreased from 3.09 to 2.90 g/cu cm. The specimen annealed at 1200 C gained 0.43 wt%, was severely deformed, and was covered with a porous layer of thick shiny glaze which could be easily peeled off. Some gas bubbles were also present on the surface. This surface layer consisted of elongated crystals of monoclinic celsian and some amorphous phase(s). The fibers in this surface ply of the CMC had broken into small pieces. The fiber-matrix interface strength was characterized through fiber push-in technique. Values of debond stress, alpha(sub d), and frictional sliding stress, tau(sub f), for the as-fabricated CMC were 0.31+/-0.14 GPa and 10.4+/-3.1 MPa, respectively. These values compared with 0.53+/-0.47 GPa and 8.33+/-1.72 MPa for the fibers in the interior of the 1200 C annealed sample, indicating hardly any change in fiber-matrix interface strength. The effects of thermal aging on microstructure were investigated using scanning electron microscopy. Only the surface ply of the 1200 C annealed specimens had degraded from oxidation whereas the bulk interior part of the CMC was unaffected. A mechanism is proposed explaining the various steps involved during the degradation of the CMC on annealing in air at 1200 C.

Bansal, Narottam P.↗

Vibrational and elastic properties of ferromagnesite across the electronic spin-pairing transition of iron

Ferromagnesite [(Mg,Fe)CO{sub 3}] has been proposed as a candidate host mineral for carbon in the Earth's mantle. Studying its physical and chemical properties at relevant pressures and temperatures helps our understanding of deep-carbon storage in the planet's interior and on its surface. Here we have studied high-pressure vibrational and elastic properties of magnesian siderite [(Mg{sub 0.35}Fe{sub 0.65})CO{sub 3}] across the electronic spin transition by Raman and X-ray diffraction spectroscopies in a diamond-anvil cell. Our results show an increase in Raman shift of the observed lattice modes of magnesian siderite across the spin transition at 45 GPa as a result of an {approx}8% unit-cell volume collapse and a 10% stiffer lattice (higher bulk modulus). C-O bond lengthening in the strong, rigid (CO{sub 3}){sup 2-} unit across the spin transition contributes to a competitive decrease in Raman shift, most evident in the Raman shift decrease of the symmetric stretching mode. Combined vibrational and elastic results are used to derive the mode Grueneisen parameter of each mode, which drops significantly across the transition. These results suggest that the low-spin state has distinctive vibrational and elastic properties compared to the high-spin state. Analyses of all recent experimental results on the (Mg,Fe)CO{sub 3} system show no appreciable compositional effect on the transition pressure, indicating weak iron-iron exchange interactions. Our results provide new insight into understanding the effects of the spin transition on the vibrational, elastic, and thermodynamic properties of (Mg,Fe)CO{sub 3} as a candidate carbon-host in the deep mantle.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Thermal equation of state of hcp-iron: Constraint on the density deficit of Earth's solid inner core: THERMAL EQUATION OF STATE OF HCP-IRON

We conducted high-pressure experiments on hexagonal close packed iron (hcp-Fe) in MgO, NaCl, and Ne pressure-transmitting media and found general agreement among the experimental data at 300 K that yield the best fitted values of the bulk modulus K 0 = 172.7(±1.4) GPa and its pressure derivative K 0 '= 4.79(±0.05) for hcp-Fe, using the third-order Birch-Murnaghan equation of state. Using the derived thermal pressures for hcp-Fe up to 100 GPa and 1800 K and previous shockwave Hugoniot data, we developed a thermal equation of state of hcp-Fe. The thermal equation of state of hcp-Fe is further used to calculate the densities of iron along adiabatic geotherms to define the density deficit of the inner core, which serves as the basis for developing quantitative composition models of the Earth's inner core. We determine the density deficit at the inner core boundary to be 3.6%, assuming an inner core boundary temperature of 6000 K.

58 GEOSCIENCES↗

Experimental evidence for dynamic friction on rock fractures from frequency-dependent nonlinear hysteresis and harmonic generation: Low-Frequency Torsional Dynamic Friction

Frictional properties affect the propagation of high-amplitude seismic waves across rock fractures and faults. Laboratory evidence suggests that these properties can be measured in active seismic surveys, potentially offering a route to characterizing friction in situ. Here, we present experimental results from a subresonance torsional modulus and attenuation apparatus that utilizes micron-scale sinusoidal oscillations to probe the nonlinear stress-strain relation at a range of strain amplitudes and rates. Nonlinear effects are further quantified using harmonic distortion; however, time series data best illuminate underlying physical processes. The low-frequency stress-strain hysteretic loops show stiffening at the sinusoid's static ends, but stiffening is reduced above a threshold frequency. This shape is determined by harmonic generation in the strain; the stress signal has no harmonics, confirming that the fractured sample is the source of the nonlinearity. These qualitative observations suggest the presence of rate-dependent friction and are consistent between fractures in three different rock types. We propose that static friction at the low strain rate part of the cycle, when given sufficient “healing” time at low oscillation frequencies, causes this stiffening cusp shape in the hysteresis loop. While rate-and-state friction is commonly used to represent dynamic friction, it cannot capture static friction or negative slip velocities. So we implement another dynamic friction model, based on the work of Dahl, which describes this process and produces similar results. Since the two models have a similar form, parameterizations of field data could constraint fault model inputs, such as specific location velocity strengthening or weakening properties.

58 GEOSCIENCES↗

Influence of Polymer and Support Interactions on the Electrocatalytic Properties of Heterogenized Molecular Complexes

Heterogenized molecular catalysts have been the subject of increasing interest in the context of electrochemical small molecule activation due to the possibility of active site homogeneity and tunability, which can surpass many nanostructured materials. When molecular catalysts strongly interact with carbon supports through π–π interactions, they tend to show higher selectivity and activity during heterogeneous electrochemical reactions. Indeed, ligand modifications in the secondary sphere that allow for more π–π overlap between catalyst and carbon support often show improved performance. Interactions between catalyst and polymer binder are also a possible modulus of control in these reactions, either through coordinating moieties that interact with active sites or through control over substrate or product transport. Finally, the covalent linking of molecular complexes onto carbon materials has also been shown to result in high activity and stability. Recent advances in the use of carbon supports, both through covalent and non-covalent interactions, and polymers to alter small molecule activation by heterogenized molecular catalysts are summarized in this Perspective.

Johnson, Elizabeth K. [University of Virginia, Cha↗

Residual fracture energy of natural and recycled aggregate concrete after exposure to high temperatures

Abstract Fracture energy ( G F ) represents the average total energy consumed in the whole process of crack propagation. Using one parameter of G F , it is not sufficient to describe the fracture behavior during crack stable and unstable propagation periods. In this study, the G F , stable fracture energy ( G FS ) and unstable fracture energy ( G FU ) of natural and recycled aggregate concrete (RAC) were investigated by using three‐point bending tests. Totally, 128 cubic specimens (100 mm × 100 mm × 100 mm) and 64 notched beams with size of 510 mm × 100 mm × 100 mm were manufactured to test the compressive strength ( f cu ), splitting tensile strength ( f t ), load–deflection (P‐δ), and load‐cracking mouth opening displacement (P‐CMOD) curves, considering different replacement levels (0%, 30%, 70%, and 100%) of recycled coarse aggregate (RA) and high temperatures exposure (20, 100, 200, and 300°C). The effects of RA substitutions and temperatures on basic mechanical properties, G F , G FS , and G FU were analyzed. The results demonstrated that the f cu , f t , and elastic modulus ( E ) decreased with the incremental temperature. The G FS of concrete with different RA substitutions first decreased and then increased, and the minimum value appeared at 200°C. The G F and G FU of concrete with different RA substitutions increased with the elevated temperature, and the increase rate decreased with RA substitutions. When the temperature is less than 100°C, the G F and G FU of concrete remained mostly unchanged with the increase of RA substitutions, while the temperature reached 200 and 300°C, the G F and G FU of concrete increased and decreased with the increase of RA substitutions, respectively.

Chen, Wei↗

Pressure induced structural changes in the potential hydrogen storage compound ammonia borane: A combined X-ray, neutron and theoretical investigation

The crystal structure of NH{sub 3}BH{sub 3} was investigated using synchrotron high pressure X-ray diffraction (HPXRD) up to 27 GPa and neutron diffraction up to 5 GPa. Density functional theoretical (DFT) calculations were carried out simultaneously for comparison. The results confirm a pressure induced phase transition from the tetragonal I4mm phase to a high pressure orthorhombic Cmc21 phase around 1.22 GPa. Further increase of pressure above 8 GPa, we observed a second structural transition from Cmc21 to a triclinic P1 phase which are reversible with small hysteresis. The transition pressures and the bulk modulus obtained experimentally are in good agreement with theory.

08 HYDROGEN↗

Effects of particle inclusions on cracking in ultrathin barrier films

Here, the effects of particle inclusions with different mechanical properties on the development of cracks in ultra-thin barrier films have been studied. Two types of particles, alumina and poly(styrene-b-methyl methacrylate) with large differences in their elastic modulus were used, representing both hard and soft inclusions. Particles were seeded onto polyethylene naphthalate substrates and subsequently coated with atomic layer deposited Al 2 O 3 as a barrier film. Ca corrosion tests used to determine the performance of the barrier films revealed that soft polymer particle inclusions severely affect the development of cracking in barrier films as compared to stiff ceramic particles. Tensile tests also confirmed that the barrier films with polymer particle inclusions have the lowest value of critical onset strain. Parametric simulations, conducted by varying the elastic modulus of the particle inclusions over a wide range, resulted in a larger strain energy release rate near particle inclusions which promotes crack formation and negatively impacts the performance of barrier films with softer particle inclusions. Thus, the combination of high residual stresses in the barrier films with the presence of soft particle inclusions is found the most detrimental for the development of high-performance ultrathin barrier films.

36 MATERIALS SCIENCE↗

Understanding Geometry and Microstructure Interactions In LPBF By Linking Lab Scale Studies To Real Part Case Examples

The mechanical properties derived from simple tensile tests are uniquely important in the design and qualification of load bearing metallic components. The tensile properties in standards for wrought metallic materials are generally accessible for design and simulation engineers, but this is not the case for additively manufactured metals. This work investigates the influence of tensile specimen geometry on the mechanical properties of laser powder bed fusion (LPBF) additively manufactured Ti-6Al-4V, particularly in relation to properties measured from specimens excised from an exemplar part. A comprehensive analysis was conducted across various specimen geometries, considering factors such as thermal history, cross-sectional area, shape, and surface roughness. Key findings reveal that sample size, particularly cross-sectional area, significantly affects reported tensile properties, with ASTM E8 flat and round specimens exhibiting differences in elastic modulus (13%), yield strength (17%), ultimate tensile strength (UTS) (14%), and elongation to failure (11%). Additionally, surface roughness was found to have a limited impact on ASTM round geometries, but it becomes critical in thin-walled and small high-throughput samples. The ASTM flat samples closely matched the properties of samples excised from the exemplar part, underscoring the necessity of testing witness samples that accurately represent end-use conditions. Furthermore, mechanical properties of samples built within the stitch zone of the exemplar part demonstrated reduced ductility, highlighting the importance of laser alignment and qualification in multi-laser additive manufacturing processes. Overall, this study emphasizes the need for careful consideration of specimen geometry and testing conditions to ensure accurate reporting of mechanical properties in LPBF Ti-6Al-4V.

36 MATERIALS SCIENCE↗

Potential seal candidates for high-energy propellants

Five potential seal candidates (linear Tefzel, linear Halar, crosslinked Halar, Viton ECD-006, and phosphazine fluoroelastomer) were evaluated for the orbital maneuvering system of the space shuttle. Since this system employs nitrogen tetroxide (N2O4) and monomethyl hydrazine (MMH) as hypergolic propellants, the seal candidates were selected on the basis of projected chemical resistance as well as rheological behavior. Chemical resistance to these high-energy fuels was determined via conventional isothermal and thermal cycling immersion tests. Rheological measurements, however, were performed on O-rings molded from the subject seal candidates. Properties determined, such as cyclic work and hysteresis, stress relaxation, and indicated modulus, therefore, relate to the O-ring seals themselves.

Merz, P. L.↗

Utilization of municipal solid waste incineration fly ash for sulfoaluminate cement clinker production

Highlights: > The replacement can be taken up to 30% of MSWI fly ash in the raw mix. > The novelty compositional parameters were defined, their optimum values were determined. > Expansive property of SAC is strongly depended on gypsum content. > Three leaching test methods are used to assess the environmental impact. - Abstract: The feasibility of partially substituting raw materials with municipal solid waste incineration (MSWI) fly ash in sulfoaluminate cement (SAC) clinker production was investigated by X-ray diffraction (XRD), compressive strength and free expansion ratio testing. Three different leaching tests were used to assess the environmental impact of the produced material. Experimental results show that the replacement of MSWI fly ash could be taken up to 30% in the raw mixes. The good quality SAC clinkers are obtained by controlling the compositional parameters at alkalinity modulus (C{sub m}) around 1.05, alumina-sulfur ratio (P) around 2.5, alumina-silica ratio (N) around 2.0{approx}3.0 and firing the raw mixes at 1250 deg. C for 2 h. The compressive strengths of SAC are high in early age while that develop slowly in later age. Results also show that the expansive properties of SAC are strongly depended on the gypsum content. Leaching studies of toxic elements in the hydrated SAC-based system reveal that all the investigated elements are well bounded in the clinker minerals or immobilized by the hydration products. Although some limited positive results indicate that the SAC prepared from MSWI fly ash would present no immediate thread to the environment, the long-term toxicity leaching behavior needs to be further studied.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Pressure induced silver ion displacement in La{sub 3}Ag{sub 0.82}SnS{sub 7}

Highlights: Black-Right-Pointing-Pointer The silver ion shifts with increasing pressure in the direction of the central-point of sulphur trigonal antiprism. Black-Right-Pointing-Pointer Coordination number changes from CN = 3 to CN = 6 at {approx}3 GPa. Black-Right-Pointing-Pointer Zero-pressure bulk modulus is B{sub 0} = 61.74 GPa and the pressure derivative is B{sup Prime }{sub 0}=4.02. Black-Right-Pointing-Pointer No phase transition up to 4.5 GPa was detected. -- Abstract: The compounds with the general formula Ln{sub 3}MTX{sub 7} (space group P6{sub 3}) (Ln - rare-earth element, M - monovalent element (Cu, Ag), T - Si, Ge, Sn and X - S, Se) are interesting owing to the possible application in the field of ionic conductivity. In the crystal structure the face-sharing [Ag(S){sub 6}] triangular antiprisms form the channels where the Ag{sup +} ion can migrate along the crystallographic c axis. High-pressure X-ray diffraction shows that Ag{sup +} ion moves towards the central-point of [Ag(S){sub 6}] when pressure is risen. As a consequence, the coordination number of Ag{sup +} changes from CN = 3 to CN = 6 at {approx}3 GPa. The La{sub 3}Ag{sub 0.82}SnS{sub 7} has stiff structure; zero-pressure bulk modulus is B{sub 0} = 61.74 GPa and the pressure derivative is B{sup Prime }{sub 0}=4.02.

36 MATERIALS SCIENCE↗

Theoretical calculations for structural, elastic, and thermodynamic properties of RuN{sub 2} under high pressure

The structural and elastic properties of RuN{sub 2} were investigated through the first-principles calculation using generalized gradient approximation (GGA) and local density approximation (LDA) within the plane-wave pseudopotential density functional theory. The obtained equilibrium structure and mechanical properties are in excellent agreement with other theoretical results. Then we compared the elastic modulus of RuN{sub 2} with several other isomorphic noble metal nitrides. Results show that RuN{sub 2} can nearly rival with OsN{sub 2} and IrN{sub 2}, which indicate RuN{sub 2} is a potentially ultra-incompressible and hard material. By the elastic stability criteria, it is predicted that RuN{sub 2} is stable in our calculations (0–100 GPa). The calculated B/G ratios indicate that RuN{sub 2} possesses brittle nature at 0 GPa and when the pressure increases to 13.4 GPa (for LDA) or 20.8 GPa (for GGA), it begins to prone to ductility. Through the quasi-harmonic Debye model, we also investigated the thermodynamic properties of RuN{sub 2}.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Equation of state and structural transition at high hydrostatic pressures in the BiFeO[subscript 3] crystal

Change in the crystal structure of the BiFeO{sub 3} multiferroic at high pressures up to 70 GPa in a diamond anvil cell has been studied by the method of synchrotron x-ray diffraction at room temperature. The experiment has been carried out under hydrostatic conditions with helium as a pressure-transferring medium. An anomaly has been observed in the behavior of the structural parameters at pressures P{sub c} {approx} 40-50 GPa. This anomaly correlates with the effect of the magnetic collapse of iron moments revealed in this pressure range. It has been found that the bulk compression modulus is equal to B{sub 0} = (75.5 {+-} 15.5) GPa in the interval 0 < P < P{sub c} and is almost quadrupled to a value of B = (292 {+-} 9) GPa in the interval P > P{sub c}. When the pressure decreases, the behavior of the structural parameters is completely reversible in correlation with the reversibility of the magnetic transition. The 'diffuseness' of the structural transition in pressure is explained by thermal fluctuations between the high-and low-spin states of Fe{sup 3+} ions in the transition region.

36 MATERIALS SCIENCE↗

Phase comparison and equation of state for Ta 2 O 5

Abstract Tantalum pentoxide (Ta 2 O 5 ) is among the most technologically useful heavy transition metal oxides. Unfortunately, its crystal structure is the subject of long-standing and unresolved disagreement. Among other consequences, this uncertainty has made it impossible to formulate a robust high pressure equation of state for Ta 2 O 5 . Here, we report the results of high pressure x-ray diffraction experiments indexed against a comprehensive list of proposed Ta 2 O 5 phases. Five of the proposed phases produce good matches to experimental observations, and the compressibility parameters for these phases are all consistent within uncertainty. This means that regardless of the particular phase chosen, the Ta 2 O 5 equation of state can be described with bulk modulus K 0 = 138 ± 3.68 GPa and pressure derivative K 0 ′ = 1.82 ± 0.45 . Combining these experimental results with new density-functional theory calculations allows us to identify the λ phase as the best structural model of Ta 2 O 5 at ambient conditions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Chloride diffusivity, chloride threshold, and corrosion initiation in reinforced alkali-activated mortars: Role of calcium, alkali, and silicate content

The aim of this study is to investigate systematically the chloride diffusivity and chloride threshold of a wide range of calcium-rich and fly ash-dominated alkali-activated samples in light of their compositional differences. To this end, the effects of various fly ash (FA)-to-slag ratios, of alkali concentrations and of silicate content in the activator were investigated. The electrochemical aspects of the passive samples were also assessed. Results show the prominent role of calcium in the matrix to reduce the chloride diffusivity. While higher alkali concentration increased the porosity and chloride diffusivities in general, lower modulus ratios provided considerably better performance in the FA-dominated samples. Chloride threshold values range between 0.19 (wt% binder mass) for calcium-rich mortars fabricated at low levels of alkalinities and 0.69 for FA-dominated mortars fabricated with highly alkaline activators. Half-cell potential and polarization resistance of alkali-activated samples were in general lower than their Portland cement counterparts.

36 MATERIALS SCIENCE↗

Nanostructured cobalt powders synthesised by polyol process and consolidated by Spark Plasma Sintering: Microstructure and mechanical properties

Bulk nanostructured cobalt was processed using a bottom-up strategy. Nanostructured particle agglomerates of about 50 and 240 nm in diameter were synthesised using a polyol route and subsequently consolidated by Spark Plasma Sintering (SPS). The microstructure of the starting powders and of the processed bulk samples was studied and characterised by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The XRD patterns of the as-prepared powders showed predominantly a face centred cubic (fcc) crystalline phase, whereas both fcc and hexagonal close packed (hcp) phases were found within the consolidated samples. A sample with the highest relative mass density (94.5%) was obtained from the small powder particles. TEM observations revealed a lamellar substructure with a high density of nanotwins and stacking faults in every grain in the sample with the highest density. Brillouin light scattering (BLS) and quasistatic compression tests were used to investigate the mechanical properties of the consolidated samples. The two techniques yielded Young modulus values of 168 GPa and 130 GPa, respectively, in the sample with the highest density. This sample also exhibited a yield stress higher than 1 GPa after the compression test, which is mainly attributed to the lamellar-like structure occurring in almost every grain of the polycrystalline aggregate. - Highlights: Black-Right-Pointing-Pointer Cobalt nanoparticles produced by the polyol process present mainly the fcc metastable phase. Black-Right-Pointing-Pointer Bulk nanostructured cobalt is obtained from the nano-particles by Spark Plasma Sintering consolidation. Black-Right-Pointing-Pointer Nanotwins and stacking faults are present in every grain of the more dense sample. Black-Right-Pointing-Pointer Yield strength and plastic domain may be varied depending on the nanoparticle size and the porosity of the consolidated material.

36 MATERIALS SCIENCE↗

Mechanically induced self-propagating reaction and consequent consolidation for the production of fully dense nanocrystalline Ti{sub 55}C{sub 45} bulk material

We employed a high-energy ball mill for the synthesis of nanograined Ti{sub 55}C{sub 45} powders starting from elemental Ti and C powders. The mechanically induced self-propagating reaction that occurred between the reactant materials was monitored via a gas atmosphere gas-temperature-monitoring system. A single phase of NaCl-type TiC was obtained after 5 h of ball milling. To decrease the powder and grain sizes, the material was subjected to further ball milling time. The powders obtained after 200 h of milling possessed spherical-like morphology with average particle and grain sizes of 45 μm and 4.2 nm, respectively. The end-products obtained after 200 h of ball milling time, were then consolidated into full dense compacts, using hot pressing and spark plasma sintering at 1500 and 34.5 MPa, with heating rates of 20 °C/min and 500 °C/min, respectively. Whereas hot pressing of the powders led to severe grain growth (∼ 436 nm in diameter), the as-spark plasma sintered powders maintained their nanograined characteristics (∼ 28 nm in diameter). The as-synthesized and as-consolidated powders were characterized, using X-ray diffraction, high-resolution electron microscopy, and scanning electron microscopy. The mechanical properties of the consolidated samples obtained via the hot pressing and spark plasma sintering techniques were characterized, using Vickers microhardness and non-destructive testing techniques. The Vickers hardness, Young's modulus, shear modulus and fracture toughness of as-spark plasma sintered samples were 32 GPa, 358 GPa, 151 GPa and 6.4 MPa·m{sup 1/2}, respectively. The effects of the consolidation approach on the grain size and mechanical properties were investigated and are discussed. - Highlights: • Room-temperature synthesizing of NaCl-type TiC • Dependence on the grain size on the ball milling time • Fabrication of equiaxed nanocrystalline grains with a diameter of 4.2 nm • Fabrication of nanocrystalline bulk TiC material by SPS with minimal grain growth • Dependence of improved mechanical properties on the consolidation techniques.

36 MATERIALS SCIENCE↗