Search NASA⌕ Search

SEARCH · Search NASA

Results for “Performance analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,423 records · Page 79

Investigation of thermal hydraulic behavior of the High Temperature Test Facility's lower plenum via large eddy simulation

A high-fidelity computational fluid dynamics (CFD) analysis was performed using the Large Eddy Simulation (LES) model for the lower plenum of the High–Temperature Test Facility (HTTF), a ¼ scale test facility of the modular high temperature gas-cooled reactor (MHTGR) managed by Oregon State University. In most next–generation nuclear reactors, thermal stress due to thermal striping is one of the risks to be curiously considered. This is also true for HTGRs, especially since the exhaust helium gas temperature is high. In order to evaluate these risks and performance, organizations in the United States led by the OECD NEA are conducting a thermal hydraulic code benchmark for HTGR, and the test facility used for this benchmark is HTTF. HTTF can perform experiments in both normal and accident situations and provide high-quality experimental data. However, it is difficult to provide sufficient data for benchmarking through experiments, and there is a problem with the reliability of CFD analysis results based on Reynolds–averaged Navier–Stokes to analyze thermal hydraulic behavior without verification. To solve this problem, high-fidelity 3-D CFD analysis was performed using the LES model for HTTF. It was also verified that the LES model can properly simulate this jet mixing phenomenon via a unit cell test that provides experimental information. As a result of CFD analysis, the lower the dependency of the sub-grid scale model, the closer to the actual analysis result. In the case of unit cell test CFD analysis and HTTF CFD analysis, the volume-averaged sub-grid scale model dependency was calculated to be 13.0% and 9.16%, respectively. As a result of HTTF analysis, quantitative data of the fluid inside the HTTF lower plenum was provided in this paper. As a result of qualitative analysis, the temperature was highest at the center of the lower plenum, while the temperature fluctuation was highest near the edge of the lower plenum wall. The power spectral density of temperature was analyzed via fast Fourier transform (FFT) for specific points on the center and side of the lower plenum. FFT results did not reveal specific frequency-dominant temperature fluctuations in the center part. It was confirmed that the temperature power spectral density (PSD) at the top increased from the center to the wake. The vortex was visualized using the well-known scalar Q-criterion, and as a result, the closer to the outlet duct, the greater the influence of the mainstream, so that the inflow jet vortex was dissipated and mixed at the top of the lower plenum. Additionally, FFT analysis was performed on the support structure near the corner of the lower plenum with large temperature fluctuations, and as a result, it was confirmed that the temperature fluctuation of the flow did not have a significant effect near the corner wall. In addition, the vortices generated from the lower plenum to the outlet duct were identified in this paper. It is considered that the quantitative and qualitative results presented in this paper will serve as reference data for the benchmark.

97 MATHEMATICS AND COMPUTING↗

Uncertainty Quantification of Bifacial Performance Modeling

Analysis on uncertainty in the annual energy of PV systems that can be attributed to parameters of particular importance to bifacial PV modules is presented. Monte Carlo simulations are used to evaluate the effect of uncertain module bifaciality factors, module transmission fractions, albedo values, and ground clearance. The analyses cover a wide spectrum of potential PV array archetypes through variation of installation parameters. The results of the Monte Carlo analysis reveal that the uncertainty is largely dependent on albedo uncertainty, but more simulations are needed to identify trends across system archetypes. The simulations are aimed at attributing an annual energy uncertainty factor for bifacial considerations that can be applied in post-processing of project probability of exceedance analysis.

energy modeling↗

Fuel Composition Effects and Other Operational Parameters on Solid Oxide Fuel Cell Performance

This analysis will address the composition of coal derived synthesis gas (syngas), and the anticipated effect that the syngas chemical constituents have on the voltage of a solid oxide fuel cell (SOFC). All calculations and figures presented herein are done on a purely thermodynamic basis. This study does not account for limitations due to cell or stack design. All simulations were conducted using an Aspen Plus 2004.1 model of an SOFC operating at atmospheric pressure. Unless otherwise noted, an SOFC overpotential of 118 mV was assumed. The Nernst potential was calculated based on exit temperature and composition, and the overpotential was subtracted to arrive at the cell operating voltage.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

NREL Data, Modeling, and Tools Empower Marine Energy Analysis

NREL performs R&D and economic analyses to drive and empower the development of wave energy and tidal, ocean, and river current energy technologies. These technologies deliver renewable electricity to the grid and provide energy solutions that support the evolving "blue economy."

HYDRO ENERGY↗

Uncertainty Quantification of Bifacial Performance Modeling

Analysis on uncertainty in the annual energy of PV systems that can be attributed to parameters of particular importance to bifacial PV modules is presented. Monte Carlo simulations are used to evaluate the effect of uncertain module bifaciality factors, module transmission fractions, albedo values, and ground clearance. The analyses cover a wide spectrum of potential PV array archetypes through variation of installation parameters. The results of the Monte Carlo analysis reveal that the uncertainty is largely dependent on albedo uncertainty, but more simulations are needed to identify trends across system archetypes. The simulations are aimed at attributing an annual energy uncertainty factor for bifacial considerations that can be applied in post-processing of project probability of exceedance analysis.

bifacial↗

Preliminary Analysis of the General Performance and Mechanical Behavior of Irradiated FeCrAl Base Alloys and Weldments

The iron-based, iron-chromium-aluminum (FeCrAl) alloys are promising, robust materials for deployment in current and future nuclear power plants. This class of alloys demonstrates excellent performance in a range of environments and conditions, including high-temperature steam (>1000°C). Furthermore, these alloys have the potential to have prolonged survival under loss-of-coolant accident (LOCA) conditions compared to the more traditional cladding materials that are either Zr-based alloys or austenitic steels. However, one of the issues associated with FeCrAl alloys is cracking during welding. The present project investigates the possibility of mitigating welding-induced cracking via alloying and precise structure control of the weldments; in the frame work of the project, several advanced alloys were developed and are being investigated prior to and after neutron irradiation to provide insight into the radiation tolerance and mechanical performance of the weldments. The present report provides preliminary results on the post-irradiation characterization and mechanical tests performed during United States Fiscal Year (FY) 2016. Chapter 1 provides a general introduction, and Chapter 2 describes the alloy compositions, welding procedure, specimen geometry and manufacturing parameters. Also, a brief discussion of the irradiation at the High Flux Isotope Reactor (HFIR) is provided. Chapter 3 is devoted to the analysis of mechanical tests performed at the hot cell facility; tensile curves and mechanical properties are discussed in detail focusing on the irradiation temperature. Limited fractography results are also presented and analyzed. The discussion highlights the limitations of the testing within a hot cell. Chapter 4 underlines the advantages of in-situ testing and discusses the preliminary results obtained with newly developed miniature specimens. Specimens were moved to the Low Activation Materials Development and Analysis (LAMDA) laboratory and prepared for mechanical tests. Tensile tests were conducted at LAMDA using a modern digital image correlation approach allowing for strain distribution analysis. Plastic strain initiation and necking are discussed in detail; a concept of strain rate maps is also introduced and discussed. Follow-on SEM-EBSD and FIBTEM analysis is planned.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Performance Refactoring of Instrumentation, Measurement, and Analysis Technologies for Petascale Computing: the PRIMA Project

The growing number of cores provided by today’s high-end computing systems present substantial challenges to application developers in their pursuit of parallel efficiency. To find the most effective optimization strategy, application developers need insight into the runtime behavior of their code. The University of Oregon (UO) and the Julich Supercomputing Centre of Forschungszentrum Julich (FZJ) developed the performance analysis tools TAU and Scalasca, respectively, which allow high-performance computing (HPC) users to collect and analyze relevant performance data – even at very large scales. TAU and Scalasca are considered among the most advanced parallel performance systems available, and are used extensively across HPC centers in the U.S., Germany, and around the world.

97 MATHEMATICS AND COMPUTING↗

The problem analysis of data processing performance in nuclear power plant computerized information and control system - 288

This paper is based on the data processing performance problems of operating command delay and system display not updating real-time for nuclear power plant computerized information and control system. The plant computerized information and control system is responsible for monitoring and controlling the plant operation, and it is a key part in the plant DCS system. Its data processing performance will affect the operation stability of nuclear power plant. The architecture, hardware configuration and data communication for plant computerized information and control system among the different levels in DCS are described. The main reasons affecting data processing performance in different signal channels are analyzed according to the plant load test results. The CPU load curves for real time server and central processing server are displayed, although the detailed cause for operating command delay and system display not updating realtime are not found, central processing server load is heavier than real time server which remind us to analyze the data processing of software resource scheduling deeply. So the resource distribution problem of software execution task is also analyzed according to CPU load test results. This paper provides the optimization analysis for data processing performance, and it is available and effective according to the latest test results. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Spotlight: efficient automated global optimization in rietveld analysis of diffraction data

Performing reliable Rietveld analysis on tens or hundreds of powder diffraction datasets from parametric or time-resolved experiments often poses a bottleneck in extracting meaningful results from the data. While automated analysis of data has recently been demonstrated, high temperature annealing studies, during which phase transformations occur and lattice parameters may change due to repartitioning of elements, are prime examples where automation by a simple phase identification from a database of room temperature structures or automation by sequential refinements is likely to fail. To enable reliable, efficient, automated Rietveld analysis, we present a Python package named Spotlight , building on established Rietveld packages such as MAUD, GSAS , or GSAS-II , which extends the refinement of best fit parameters to a global optimization using an ensemble of optimizers leveraging hierarchical parallel execution on high-performance computing clusters. Spotlight further enables the efficient design of refinement plans through the iterative automated machine-learning of a surrogate for the refinement on which the global optimizations are performed until results from the surrogate converge to the response surface data. We demonstrate Spotlight with the analysis of uranium molybdenum and Ti–6Al–4V datasets, as well as in two open-source tutorials analyzing aluminium oxide and lead sulphate.

36 MATERIALS SCIENCE↗

Advanced shield development for a fission surface power system for the lunar surface

A nuclear reactor power system such as the affordable fission surface power system enables a potential outpostonthemoon.Aradiation shieldmustbe included in the reactor system to reduce the otherwise excessive dose to the astronauts and other vital system components. The radiation shield is typically the most massive component of a space reactor system, and thus must be optimized to reduce mass asmuchas possible while still providing the required protection.Various shield options for an on-lander reactor system are examined for outpost distances of 400m and 1 kmfromthe reactor. Also investigated is the resulting mass savings from the use of a high performance cermet fuel. A thermal analysis is performed to determine the thermal behaviours of radiation shields using borated water. For an outpost located 1000m from the core, a tetramethylammonium borohydride shield is the lightest (5148.4 kg), followed by a trilayer shield (boron carbide–tungsten–borated water; 5832.3 kg), and finally a borated water shield (6020.7 kg). In all of the final design cases, the temperature of the borated water remains below 400 K.

42 ENGINEERING↗

Wind Plant Performance Prediction (WP3) Project

The methods for analysis of operational wind plant data are highly variable across the wind industry, leading to high uncertainties in the validation and bias-correction of preconstruction energy estimation methods. Lack of credibility in the preconstruction energy estimates leads to significant impacts on project financing and therefore the final levelized cost of energy for the plant. In this work, the variation in the evaluation of a wind plant's operational energy production as a result of variations in the processing methods applied to the operational data is examined. Preliminary results indicate that selection of the filters applied to the data and the filter parameters can have significant impacts in the final computed assessment metrics.

17 WIND ENERGY↗

Investigations into the Ternary NaF-KF-UF4 Salt System – Phase A

A knowledge gap exists in the data and understanding of fresh fuel salt and irradiated multicomponent fuel salt systems thermophysical properties. Quantifying these properties is necessary for the design and construction of test reactors, as well as the licensing of future commercial molten-salt reactors. To facilitate thermal property determination on a proposed fuel salt composition for Seaborg Technologies, several samples containing depleted uranium tetrafluoride (UF4), sodium fluoride (NaF), and potassium fluoride (KF) were blended, and a melt temperature analysis was performed. From the melting temperature analysis, it was determined that sample Seaborg-7, a ternary salt composition of 26.4UF4-24.7KF-48.9NaF (mol%), was very near a ternary eutectic point. Therefore, thermal properties such as melting temperature, salt stability, density, heat capacity, thermal diffusivity, and viscosity were experimentally determined on the Seaborg-7 salt. These measurements document the baseline properties of fresh fuel salt as a function of temperature, where future experiments on irradiated fuel salt will provide a holistic perspective on the change of thermophysical properties during reactor operations. Several precision instruments were used to collect property data, and instrument calibrations and data collection were performed and documented in a standardized and reproducible manner with meticulous detail. This process ensured that the measurement procedures and resulting data can readily be duplicated elsewhere. The Seaborg-7 salt was shown to be stable at temperatures up to 900°C, as no mass change was observed upon repeated heating and cooling. The peak melting temperature was determined to be 547°C (557°C endset). The enthalpy of fusion (??H?_fus^o) was determined to be 167.5 ± 2.7 J/g while the enthalpy of crystallization (??H?_c^o) was determined to be -147.8 ± 13.3 J/g. In addition to the eutectic melting peak, upon heating, several pre eutectic peaks were observed, occurring at 470°C (onset) and 499°C (peak). Specific heat capacity measurements showed a slightly increasing trend with respect to temperature in the solid phase, while the liquid-specific heat capacity showed a somewhat flat trend with an average value of 106.1 ± 1.24 J/mol·K between 600 to 800°C. Three independent trials using the Seaborg-7 salt determined the density to be ?(T) = 4.908 – 0.000363·T(°C), validated between 32 to 200°C, and ?(T) = 4.808 – 0.00113·T(°C), validated between ~575 to 850°C. Thermal diffusivity was determined for the liquid state and is represented by the linear equation y = 0.1581 + 0.000207·T(°C) between 550 to 850°C. The viscosity was determined from 600 to 800°C and is represented by the exponential fit equation, ? (mPa·s) = 736.58e^(-0.006·T(°C)). This report documents the conclusion of fuel salt thermophysical property measurements for the Seaborg SPP, Phase A project.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Status of Multiple Channel Fuel Performance Capabilities Within the SAS4A/SASSYS-1 Safety Analysis Software

SAS4A/SASSYS-1 (SAS) is a fast-running simulation tool used to perform deterministic analysis of anticipated events as well as design basis and beyond design basis accidents for advanced liquid-metal-cooled nuclear reactors. It is a critical element of safety analysis capabilities for the U.S. Department of Energy and is utilized within industry to perform the transient safety analyses required to support the licensing of Liquid Metal-cooled Fast Reactors (LMFRs). Although SAS is exceptionally fast for most transient scenarios, fuel performance calculations, along with the associated pre-transient characterization of the fuel pin, may be required for transient scenarios where fuel pin failure is hypothesized. Both the pre-transient characterization and the transient fuel performance calculation are necessary to properly quantify margins to potential fuel failure and assess the time spent potentially exceeding such margins during events. While safety analysis calculations with fuel performance models provide a more detailed characterization of the reactor during a transient, the pre-transient characterization can be time-consuming and computationally expensive. Often, large numbers of fuel pins have been exposed to similar pre-transient irradiation conditions. Similarly, the same pre-transient fuel characterization may be applicable to numerous transient conditions. This provides an opportunity to optimize the SAS computational framework such that pre-transient fuel characterization can be shared across multiple channels (fuel pins) and across multiple simulations, thus dramatically reducing overall computational costs. This report summarizes progress toward enhancing the SAS computational framework to support shared, multiple channel fuel performance characterizations intended to significantly reduce computational costs. Preliminary testing has shown that the computational time saved by using the pre-transient sharing capability is approximately equal to the time it takes to perform the pre-transient characterization.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Small Versus Large-Sized Drug-Eluting Beads (DEBIRI) for the Treatment of Hepatic Colorectal Metastases: A Propensity Score Matching Analysis

PurposeTo compare the feasibility, safety, and efficacy with small and large irinotecan drug-eluting beads (DEBIRI) for treating hepatic colorectal metastases.MethodsUsing our prospectively maintained, multi-center, intra-arterial therapy registry, we identified 196 patients treated with a combination of large beads (100–300 to 500–700 μm) and patients treated with a combination of small beads (70–150 to 100–300 μm). To minimize selection bias, a propensity score analysis was performed to compare both groups.ResultsUnadjusted analysis consisted of 196 and 30 patients treated with large and small beads, respectively. The adjusted analysis consisted of 19 patients each. Unadjusted analysis showed decreased all-grade (p = <0.001) and high-grade adverse effects (p = 0.02) in the small bead group, with a persisting trend toward decreased overall side effects in the adjusted analysis favoring small beads (p = 0.09) The adjusted analysis showed the percentage dose delivered (delivered dose/intended dose) was significantly greater in the small bead group compared to the large bead group (96 vs 79 %; p = 0.005). There were also a lower percentage of treatments terminating in complete stasis in the adjusted analysis (0.0035). Adjusted analysis also showed increased objective response rate (ORR) at 12 months (p = 0.04), with a corresponding trend also seen in the unadjusted analysis (0.09).ConclusionSmaller beads result in increased dose delivery probably due to less propensity to reach complete stasis. It may also lead to more durable long-term efficacy. Smaller beads also demonstrate similarly low toxicity compared to large-sized beads with a trend toward less toxicity.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Mechanical evaluation of WC-Co materials with varying microstructures

Tungsten carbide–cobalt materials are useful in a variety of extreme applications due to a desirable blend of properties, yet the technology has not significantly changed since their initial development in the 1920s. The mechanical properties of this class of materials is highly dependent on two variables, the size of the tungsten carbide grains, and the amount of binder phase present in the final body. In this study, the amount of binder phase is isolated across three commercial materials from the same manufacturer with three different grain sizes to investigate the effect on mechanical properties. The mechanical properties investigated are indentation hardness, flexure and tensile strength, as well as fracture toughness. In general, an increase in hardness and tensile strength with decreasing grain size was observed, while the fracture toughness showed the opposite trend with toughness increasing with increasing grain size. The flexure strength results did not show a correlation to grain size. Fractographic analysis identified the dominant strength-limiting flaw for each sample, which largely were in the form of porosity. Other flaws types, such as inclusions from the milling process, clusters of large grains, and machining cracks from the surface finishing process, were also identified. Finally, Weibull analysis was performed and deemed appropriate for analysis of these materials, but strength-size scaling was not conducted due to the variability in the strength-limiting feature between the different specimen geometries.

36 MATERIALS SCIENCE↗

Incidence of Leukoencephalopathy After Whole-Brain Radiation Therapy for Brain Metastases

Purpose: To evaluate the incidence of leukoencephalopathy after whole-brain radiation therapy (WBRT) in patients with brain metastases. Methods and Materials: We retrospectively reviewed 111 patients who underwent WBRT for brain metastases from April 2001 through March 2008 and had evaluable computed tomography (CT) and/or magnetic resonance imaging (MRI) at least 1 month after completion of WBRT. We evaluated the leukoencephalopathy according to the Common Terminology Criteria for Adverse Events, version 3.0. The patients who had brain tumor recurrence after WBRT were censored at the last follow-up CT or MRI without recurrence. To evaluate the risk factors for leukoencephalopathy, bivariate analysis was performed using a logistic regression analysis adjusted for follow-up time. Factors included in the analysis were age, gender, dose fractionation, 5-fluorouracil, methotrexate, cisplatin, and other chemotherapeutic agents. Results: The median age of the 111 patients was 60.0 years (range, 23-89 years). The median follow-up was 3.8 months (range, 1.0-38.1 months). Leukoencephalopathy developed in 23 of the 111 patients. Grades 1, 2, and 3 were observed in 8, 7, and 8 patients, respectively. The incidence was 34.4% (11 of 32), 42.9% (6 of 14), 66.7% (2 of 3), and 100% (2 of 2) of the patients who were followed up for ≥6, ≥12, ≥24, and ≥36 months, respectively. In the bivariate analysis, older age (≥65 years) was significantly correlated with higher risk of leukoencephalopathy (odds ratio 3.31; 95% confidence interval 1.15-9.50; P=.03). Conclusions: The incidence of leukoencephalopathy after WBRT was 34.4% with ≥6 months follow-up, and increased with longer follow-up. Older age was a significant risk factor. The schedule of WBRT for patients with brain metastases should be carefully determined, especially for favorable patients.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

SWIFT-BAT OBSERVATIONS OF THE RECENTLY DISCOVERED MAGNETAR SGR 0501+4516

We present results on the soft gamma repeater (SGR) 0501+4516, discovered by the Swift Burst Alert Telescope (BAT) on 2008 August 22. More than 50 bursts were identified from this source, out of which 18 bursts had enough counts to carry out spectral analysis. We performed time-averaged spectral analysis on these 18 bursts using eight models, among which the cut-off power-law (PL) and the two-blackbody models provided the best fit in the 15-150 keV energy range. The cut-off PL model fit yields a mean photon index {Gamma}{sub CPL} = 0.54 {+-} 0.11 and a cut-off energy E{sub C} = 19.1 {+-} 1.8 keV for the bursts. The mean hard and soft blackbody temperatures are found to be kT{sub BB{sub h}} = 12.8 {+-} 0.7 keV and kT{sub BB{sub s}} = 4.6 {+-} 0.5 keV, respectively, and are anti-correlated with the square of the radii of the hard and soft emitting regions (R{sub BB{sub h}} and R{sub BB{sub s}}) as R{sub BB{sub h}}{sup 2} {proportional_to} kT {sup -5.8} and R{sub BB{sub s}}{sup 2} {proportional_to} kT {sup -2.7}, respectively. The soft and hard component temperatures with different indices support the idea of two distinct emitting regions with the hard component corresponding to a smaller radius and the soft component corresponding to a larger radius, which further corroborate the idea of the propagation of extraordinary (E) and ordinary (O) mode photons across the photosphere, as predicted in the magnetar model. We notice strong burst fluence-duration correlation as well as hardness ratio-duration and hardness ratio-fluence anti-correlations for the SGR 0501+4516 bursts. The burst fluences range from {approx}4.4 x 10{sup -9} ergs cm{sup -2} to {approx}2.7 x 10{sup -6} ergs cm{sup -2}, consistent with those observed for typical short SGR bursts.

79 ASTRONOMY AND ASTROPHYSICS↗