Search NASA⌕ Search

SEARCH · Search NASA

Results for “Carrier diffusions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Forward-bias capacitance and current measurements for determining lifetimes and band narrowing in p-n junction solar cells

A new method is described and illustrated for determining the minority-carrier diffusion length and lifetime in the base region of p-n junction solar cells. The method requires only capacitance measurements at the device terminals and its accuracy is estimated to be + or - 5%. It is applied to a set of silicon p-n junction devices and the values of the diffusion lengths agree with those obtained using the current response to X-ray excitation but disagree with those obtained by the OCVD method. The reasons for the relative inaccuracy of OCVD applied to silicon devices are discussed. The capacitance method includes corrections for a two-dimensional fringing effects which occur in small area devices. For a device having highly-doped base region and surface (emitter) layer, the method can be extended to enable the determination of material properties of the degenerately doped surface layer. These material properties include the phenomenological emitter lifetime and a measure of the energy band-gap narrowing in the emitter. An alternate method for determining the energy band-gap narrowing from temperature dependence of emitter current is discussed and demonstrated.

Neugroschel, A.↗
NASA NTRS1978

Short circuit current changes in electron irradiated GaAlAs/GaAs solar cells

Heteroface p-GaAlAs/p-GaAs/n-GaAs solar cells with junction depths of 0.8, 1.5, and 4 microns were irradiated with 1 MeV electrons. The short-circuit current for the 4 micron junction depth cells is significantly reduced by the electron irradiation. Reduction of the junction depth to 1.5 microns improves the electron radiation resistance of the cells while further reduction of the junction depth to 0.8 microns improves the stability of the cells even more. Primary degradation is in the blue region of the spectrum. Considerable recovery of lost response is obtained by annealing the cells at 200 C. Computer modeling shows that the degradation is caused primarily by a reduction in the minority carrier diffusion length in the p-GaAs.

Walker, G. H.↗
NASA NTRS1979

Silicon Solar Cell Process Development, Fabrication and Analysis, Phase 1

Solar cells from RTR ribbons, EFG (RF and RH) ribbons, dendritic webs, Silso wafers, cast silicon by HEM, silicon on ceramic, and continuous Czochralski ingots were fabricated using a standard process typical of those used currently in the silicon solar cell industry. Back surface field (BSF) processing and other process modifications were included to give preliminary indications of possible improved performance. The parameters measured included open circuit voltage, short circuit current, curve fill factor, and conversion efficiency (all taken under AM0 illumination). Also measured for typical cells were spectral response, dark I-V characteristics, minority carrier diffusion length, and photoresponse by fine light spot scanning. the results were compared to the properties of cells made from conventional single crystalline Czochralski silicon with an emphasis on statistical evaluation. Limited efforts were made to identify growth defects which will influence solar cell performance.

Yoo, H. I.↗
NASA NTRS1979

Structure of deformed silicon and implications for low-cost solar cells

The paper reports on an investigation of the microstructure and minority carrier lifetime of silicon in uniaxially compressed silicon samples, the objective of which was to determine if it is feasible to produce silicon solar cells from sheet formed by high temperature deformation. It is reported that recrystallization was found to be incomplete in both fine and large grained materials, and that the major mode of recrystallization appears to be migration of existing boundaries into the deformed regions. Also, minority carrier diffusion length was found to be drastically reduced after deformation, perhaps due to contamination or cooling rate, and recovered only slightly with annealing. It is concluded that these results suggest that high temperature deformation of silicon for direct production of sheet for high efficiency solar cells is not practical. It is noted that potential may exist for its use as a coarse grained substrate.

Mardesich, N.↗
NASA NTRS1980

Origin of reverse annealing in radiation-damaged silicon solar cells

The paper employs relative defect concentrations, energy levels, capture cross sections, and minority carrier diffusion lengths in order to identify the defect responsible for the reverse annealing observed in a radiation damaged n(+)/p silicon solar cell. It is reported that the responsible defect, with the energy level at +0.30 eV, has been tentatively identified as boron-oxygen-vacancy complex. In conclusion, it is shown that removal of this defect could result in significant cell recovery when annealing at temperatures well below the currently required 400 C.

Weinberg, I.↗
NASA NTRS1980

Effects of grain boundaries in polycrystalline solar cells

In polycrystalline solar cells, the short-circuit current is reduced (compared to single-crystal cells) due to recombination of minority carriers at the grain boundaries. The magnitude of this reduction is calculated for the case of a monochromatic beam of light, assuming that both the light beam and the grain boundaries are perpendicular to a p-n junction. The photoresponse of the junction is calculated in terms of the absorption coefficient of the light, the minority-carrier diffusion length, the surface recombination velocity at the grain boundary and the distance of the light beam from the grain boundary. The analysis gives an expression for an effective grain boundary width which depends on wavelength. This width determines the reduction in short-circuit current of solar cells made from material with columnar-type grains.

Zook, J. D.↗
NASA NTRS1979

Some characteristics of low-cost silicon sheet

The paper discusses structural defects in low-cost silicon sheets and their effect on the electronic properties related to solar cell performance. Experimental data are presented on the influence of grain boundaries on minority carrier diffusion length, impurity defect interaction, and variable surface recombination velocity. An analytical model of the effect of grain boundaries on solar cell performance is constructed based on these results.

Koliwad, K. M.↗
NASA NTRS1980

Opto-electronic properties of cells made from various silicon forms

Opto-electronic properties of the various silicon forms were obtained from the solar cell performance. Performance parameters included the photovoltaic characteristics, minority carrier diffusion length, spectral response and small light spot scanning. Self consistent results were obtained from the various measurement techniques, which can provide useful information on sheet quality, as a potential for low cost terrestrial applications, and areas where the sheet formation methods can be improved.

Yoo, H.↗
NASA NTRS1981

Silicon solar cell process development, fabrication and analysis

Solar cells were fabricated from EFG ribbons dendritic webs, cast ingots by heat exchanger method, and cast ingots by ubiquitous crystallization process. Baseline and other process variations were applied to fabricate solar cells. EFG ribbons grown in a carbon-containing gas atmosphere showed significant improvement in silicon quality. Baseline solar cells from dendritic webs of various runs indicated that the quality of the webs under investigation was not as good as the conventional CZ silicon, showing an average minority carrier diffusion length of about 60 um versus 120 um of CZ wafers. Detail evaluation of large cast ingots by HEM showed ingot reproducibility problems from run to run and uniformity problems of sheet quality within an ingot. Initial evaluation of the wafers prepared from the cast polycrystalline ingots by UCP suggested that the quality of the wafers from this process is considerably lower than the conventional CZ wafers. Overall performance was relatively uniform, except for a few cells which showed shunting problems caused by inclusions.

Yoo, H. I.↗
NASA NTRS1981

Silicon solar cell process development, fabrication, and analysis

Work has progressed in fabrication and characterization of solar cells from ubiquitous crystallization process (UCP) wafers and LASS ribbons. Gettering tests applied to UCP wafers made little change on their performance compared with corresponding baseline data. Advanced processes such as shallow junction (SJ), back surface field (BSF), and multilayer antireflection (MLAR) were also applied. While BSF by Al paste had shunting problems, cells with SJ and BSF by evaporated Al, and MLAR did achieve 14.1% AMI on UCP silicon. The study of LASS material was very preliminary. Only a few cells with SJ, BSR, (no BSF) and MLAR were completed due to mechanical yield problems after lapping the material. Average efficiency was 10.7% AMI with 13.4% AMI for CZ controls. Relatively high minority carrier diffusion lengths were obtained. The lower than expected Jsc could be partially explained by low active area due to irregular sizes.

Yoo, H. I.↗
NASA NTRS1983

Correlation of solar cell electrical properties with material characteristics of silicon cast by the ubiquitous crystallization process

Solar cells were fabricated using a conservative 'baseline' process on 1-3 Omega-cm p-type silicon from ingots cast by the ubiquitous crystallization process. Conversion efficiencies of the cells were measured, as well as spectral response and minority carrier diffusion length. Adjacent slices from the same ingot were studied for their grain size, dislocation distribution, and impurity distribution. Cell performance was related to the observed structural features, as well as to the chemical structure of the ingot.

Hyland, S.↗
NASA NTRS1983

Process Research On Polycrystalline Silicon Material (PROPSM)

The performance-limiting mechanisms in large-grain (greater than 1 to 2 mm in diameter) polycrystalline silicon solar cells were investigated by fabricating a matrix of 4 sq cm solar cells of various thickness from 10 cm x 10 cm polycrystalline silicon wafers of several bulk resistivities. Analysis of the illuminated I-V characteristics of these cells suggests that bulk recombination is the dominant factor limiting the short-circuit current. The average open-circuit voltage of the polycrystalline solar cells is 30 to 70 mV lower than that of co-processed single-crystal cells; the fill-factor is comparable. Both open-circuit voltage and fill-factor of the polycrystalline cells have substantial scatter that is not related to either thickness or resistivity. This implies that these characteristics are sensitive to an additional mechanism that is probably spatial in nature. A damage-gettering heat-treatment improved the minority-carrier diffusion length in low lifetime polycrystalline silicon, however, extended high temperature heat-treatment degraded the lifetime.

Culik, J. S.↗
NASA NTRS1984

A High-speed Characterization Technique for Solar Silicon

High-speed crystal growth techniques demand high-speed characterization techniques to allow a timely feed-back of information to the crystal growers. The unique properties of the Si electrolyte-contact (SEC) provide for an extremely fast and simple measurement of the light-induced photo-current for any piece of Si without lengthy preparation of the specimen. Electropolishing at high anodic current densities allows for insitu generation of fresh surfaces whereas preferential etching of defects in various modes is possible at low current densities. In n-type Si a simple estimation of the minority-carrier diffusion length is possible in many cases. Laser-scanning enables local probing of the photocurrent and provides data about the homogeneity of a sample. The experimental realization of the method is described in detail and examples are given and discussed.

Lehmann, V.↗
NASA NTRS1983

Silicon solar cell process development, fabrication and analysis

Measurements of minority carrier diffusion lengths were made on the small mesa diodes from HEM Si and SILSO Si. The results were consistent with previous Voc and Isc measurements. Only the medium grain SILSO had a distinct advantage for the non grain boundary diodes. Substantial variations were observed for the HEM ingot 4141C. Also a quantitatively scaled light spot scan was being developed for localized diffusion length measurements in polycrystalline silicon solar cells. A change to a more monochromatic input for the light spot scan results in greater sensitivity and in principle, quantitative measurement of local material qualities is now possible.

Leung, D. C.↗
NASA NTRS1984

Process Research of Polycrystalline Silicon Material (PROPSM)

An investigation was begun into the usefulness of molecular hydrogen annealing on polycrystalline solar cells. No improvement was realized even after twenty hours of hydrogenation. Thus, samples were chosen on the basis of: (1) low open circuit voltage; (2) low shunt conductance; and (3) high light generated current. These cells were hydrogenated in molecular hydrogen at 300 C. The differences between the before and after hydrogenation values are so slight as to be negligible. These cells have light generated current densities that indicate long minority carrier diffusion lengths. The open circuit voltage appears to be degraded, and quasi-neutral recombination current enhanced. Therefore, molecular hydrogen is not usful for passivating electrically active defects.

Culik, J. S.↗
NASA NTRS1982

Directional solidification of silicon in carbon crucibles by an oscillating crucible technique

The quality of silicon cast by present techniques is limited by the presence of dislocations and grain boundaries in unseeded growth and by cellular structures with dislocation networks in the case of the seeded growth. To address these concerns, a new method of directional solidification called the oscillating crucible technique (OCT) is developed. During growth, a carbon crucible is oscillated to provide for effective stirring of the melt. This growth technique (seeded growth only), along with material characterization and solar-cell fabrication and testing, is described. Solar-cell efficiencies of up to 13 percent at 100 mW/sq cm area obtained in the single crystalline areas. Minority-carrier diffusion lengths exceeding 100 microns are measured even in the polycrystalline areas of the wafers. Limitations of the present setup and possible future improvements are discussed.

Daud, T.↗
NASA NTRS1984

Uncertainties about the physical electronics of n(+) and p(+) silicon, with applications for solar cells

After brief surveys of the significance of n(+) and p(+) silicon for the conversion efficiency of solar cells, the work in this paper is concentrated on uncertainties in the characterization of n(+) and p(+) regions. The topics treated include the quantum density states of the majority carrier band and the position of the Fermi level relative to the edge of this band, the resulting force field on the minority carriers accompanying a space dependence of the energy gap narrowing, and the interpretation of measurements of the energy gap narrowing and the minority carrier diffusivity and mobility. The treatment seeks to show how these uncertainties relate to solar cell design and to estimates of attainable conversion efficiency.

Lindholm, F. A.↗
NASA NTRS1985

Process Research on Polycrystalline Silicon Material (PROPSM)

Results of hydrogen-passivated polycrysalline silicon solar cell research are summarized. The short-circuit current of solar cells fabricated from large-grain cast polycrystalline silicon is nearly equivalent to that of single-crystal cells, which indicates long bulk minority-carrier diffusion length. Treatments with molecular hydrogen showed no effect on large-grain cast polycrystalline silicon solar cells.

Culik, J. S.↗