Search NASA⌕ Search

SEARCH · Search NASA

Results for “FET's”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Highly Responsive Near-Infrared Photodetector Based on Contactless PdSe 2 Integration with a Few-Layered MoSe 2 Field-Effect Transistor

Two-dimensional (2D) semiconductors with narrow bandgaps are promising candidates for near- and far-infrared (IR) photodetection, particularly in the telecommunication spectral window. However, current low-bandgap IR photodetectors face significant challenges due to their high dark current, increased carrier recombination, and thermally generated noise. Here, in this work, a hybrid phototransistor is demonstrated by integrating direct, contact-free palladium diselenide (PdSe 2 ) as a highly responsive IR detection layer with a non-IR-absorbing molybdenum diselenide (MoSe 2 ) field-effect transistor (FET), using a near-IR source at a wavelength of λ = 1650 nm. Exfoliated PdSe 2 flakes integrated into a back-gated FET architecture exhibit ambipolar transport behavior, with extracted hole and electron mobilities of 24.8 cm 2 V –1 s –1 and 58.4 cm 2 V –1 s –1 , respectively. The devices show a clear photocurrent generation under the illumination of a λ = 1650 nm laser source, achieving a notable responsivity of ∼300 mA W -1 at an applied gate voltage of 15 V, which highlights the suitability of PdSe 2 as a narrow-bandgap material for photodetection. Photoresponsivity saturates and does not have any effect above an applied gate voltage of 15 V. To further tune the photoresponsivity performance continuously with the applied gate voltage, we construct a van der Waals heterostructure phototransistor, where few layers of PdSe 2 are directly transferred onto the 2D channel region of a MoSe 2 FET, while avoiding any contact with the metal electrodes. In this heterostructure, PdSe 2 works as the primary active IR-absorbing layer, while MoSe 2 provides high-performance FET characteristics. This spatial separation of absorption and transport facilitates efficient interlayer charge transfer and charge separation, resulting in high responsivities of up to 972 mA W –1 at near-IR wavelengths and a low power density of 1.5 mW/mm 2 . The responsivity of our photodetector is comparable to that of some state-of-the-art commercially available NIR photodetectors, highlighting the potential of PdSe 2 -based heterostructures as scalable, CMOS-compatible platforms for high-performance near-IR detection.

Infrared (IR) photodetectors↗
DOE OSTI2022

Remote Floating-Gate Field-Effect Transistor with 2-Dimensional Reduced Graphene Oxide Sensing Layer for Reliable Detection of SARS-CoV-2 Spike Proteins

Despite intensive research of nanomaterials-based field-effect transistors (FETs) as a rapid diagnostic tool, it remains to be seen for FET sensors to be used for clinical applications due to a lack of stability, reliability, reproducibility, and scalability for mass production. In this work, we propose a remote floating-gate (RFG) FET configuration to eliminate device-to-device variations of two-dimensional reduced graphene oxide (rGO) sensing surfaces and most of the instability at the solution interface. Also, critical mechanistic factors behind the electrochemical instability of rGO such as severe drift and hysteresis were identified through extensive studies on rGO–solution interfaces varied by rGO thickness, coverage, and reduction temperature. rGO surfaces in our RFGFET structure displayed a Nernstian response of 54 mV/pH (from pH 2 to 11) with a 90% yield (9 samples out of total 10), coefficient of variation (CV) < 3%, and a low drift rate of 2%, all of which were calculated from the absolute measurement values. As proof-of-concept, we demonstrated highly reliable, reproducible, and label-free detection of spike proteins of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) in a saliva-relevant media with concentrations ranging from 500 fg/mL to 5 μg/mL, with an R 2 value of 0.984 and CV < 3%, and a guaranteed limit of detection at a few pg/mL. Taken together, this new platform may have an immense effect on positioning FET bioelectronics in a clinical setting for detecting SARS-CoV-2.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Persistent and reversible electrostatic control of doping in graphene/hexagonal boron nitride heterostructures

Since its first application as a substrate for graphene field effect transistors (FETs), hexagonal boron nitride (hBN) has become a prominent component in two-dimensional (2D) material devices. In addition, hBN has been shown to host defects that can be manipulated to change the electronic properties of adjacent 2D materials. Despite the wide use of such defect manipulations, no focused efforts have been made to further the understanding of defect excitations and their influence in graphene/hBN FETs. In this study, we explore the effect of high electric fields (~10 V/nm) on graphene/hBN FETs and find that persistent and reversible shifts in graphene's charge neutrality point (CNP) occur. By increasing the applied electric field and temperature of our device, we find that this CNP shift is enhanced. With this insight, we propose a mechanism that explains these observations based on Poole–Frenkel emissions from defects in hBN. Finally, we show that such an effect may be suppressed by using graphite as a backgate, thus preventing unintended changes in the electrical properties of graphene/hBN FETs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Elimination of the bias-stress effect in ligand-free quantum dot field-effect transistors

Field-effect transistors (FETs) made from colloidal quantum dot (QD) solids commonly suffer from current–voltage hysteresis caused by the bias-stress effect (BSE), which complicates fundamental studies of charge transport in QD solids and the use of QD FETs in electronics. Here, we show that the BSE can be eliminated in n-channel PbSe QD FETs by first removing the QD ligands with a dose of H 2 S gas and then infilling the QD films with alumina by atomic layer deposition (ALD). The H 2 S-treated, alumina-infilled FETs have stable, hysteresis-free device characteristics (total short-term stability), indefinite air stability (total long-term stability), and a high electron mobility of up to 14 cm 2 V −1 s −1 , making them attractive for QD circuitry and optoelectronic devices. The BSE-free devices are utilized to conclusively establish the dependence of the electron mobility on temperature and QD diameter. We demonstrate that the BSE in these devices is caused by both electron trapping at the QD surface and proton drift within the film. The H 2 S/alumina chemistry produces ligand-free PbSe/PbS/Al 2 O 3 interfaces that lack the traps that cause the electronic part of the BSE, while full alumina infilling stops the proton motion responsible for the ionic part of the BSE. In conclusion, our matrix engineering approach should aid efforts to eliminate the BSE, boost carrier mobilities, and improve charge transport in other types of nanocrystal solids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Gate control of electron correlations towards Mott field effect transistors (MottFET)

The modulation of channel conductance in field-effect transistors (FETs) via metal-insulator-semiconductor structures has revolutionized information processing and storage. However, the limitations of silicon-based FETs in electrical switching have driven the search for new materials capable of overcoming these constraints. Electrostatic gating of competing electronic phases in a Mott material near its metal-to-insulator transition (MIT) offers the prospects of substantial modulation of the conducting electrons and electrical resistivity through small changes in band filling. While electrostatic control of the MIT has been previously reported, the advancement of Mott materials toward novel Mott-based transistors, MottFETs requires the realization of their unique physical properties in a solid-state device. In this study, we present gate control of electron correlation using a solid-state device utilizing the oxide Mott system La 1-x Sr x VO 3 as a correlated FET channel. We report on a gate resistance response that cannot be explained in a purely electrostatic framework. This behavior suggests an enhancement in effective mass and a reduction in effective carrier density as the system approaches its insulating state, consistent with theoretical predictions for Mott systems, suggesting at least 100× charge gain originating from the correlated behavior. These preliminary results pave the way toward the development of highly efficient, low-power electronic devices that could surpass the performance bottlenecks of conventional FETs by leveraging the electronic phase transitions of correlated electron systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Fabrication of field-effect transistors with transfer-free nanostructured carbon as semiconducting channel material

Carbon nanostructures as active channel material in field effect transistors (FETs) are appealing in microelectronics for their improved performance such as high speed and low energy dissipation. However, these devices require the incorporation of nanostructure transfer steps in the fabrication process flow, which makes difficult its application in large scale integration circuits. Here we present a novel method for the fabrication of FETs with nanostructured carbon in the channel with p-type semiconducting properties and intermediate drain-source current (IDS) on/off ratio. The method is based on the use of Ni nanoparticles in the source-drain gap region as seed material for the formation of carbon nanostructures in the FET channel. FETs without Ni nanoparticles in the channel showed no modulation of IDS as a function of gate voltage. The device fabrication process does not require any carbon nanostructure transfer steps since it directly forms carbon nanostructures electrically connected to the device's source and drain electrodes via electron-beam evaporation of carbon and conventional lithographic processes. Since all device fabrication steps are compatible with Si technology processes, they are capable of being further optimized following process development protocols practiced by the semiconductor industry.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Non-Carbon 2D Materials-Based Field-Effect Transistor Biosensors: Recent Advances, Challenges, and Future Perspectives

In recent years, field-effect transistors (FETs) have been very promising for biosensor applications due to their high sensitivity, real-time applicability, scalability, and prospect of integrating measurement system on a chip. Non-carbon 2D materials, such as transition metal dichalcogenides (TMDCs), hexagonal boron nitride (h-BN), black phosphorus (BP), and metal oxides, are a group of new materials that have a huge potential in FET biosensor applications. In this work, we review the recent advances and remarkable studies of non-carbon 2D materials, in terms of their structures, preparations, properties and FET biosensor applications. We will also discuss the challenges facing non-carbon 2D materials-FET biosensors and their future perspectives.

2D-materials↗
NASA NTRS1983

The 30-GHz monolithic receive module

Key requirements for a 30 GHz GaAs monolithic receive module for spaceborne communication antenna feed array applications include an overall receive module noise figure of 5 dB, a 30 dB RF to IF gain with six levels of intermediate gain control, a five-bit phase shifter, and a maximum power consumption of 250 mW. The RF designs for each of the four submodules (low noise amplifier, some gain control, phase shifter, and RF to IF sub-module) are presented. Except for the phase shifter, high frequency, low noise FETs with sub-half micron gate lengths are employed in the submodules. For the gain control, a two stage dual gate FET amplifier is used. The phase shifter is of the passive switched line type and consists of 5-bits. It uses relatively large gate width FETs (with zero drain to source bias) as the switching elements. A 20 GHz local oscillator buffer amplifier, a FET compatible balanced mixer, and a 5-8 GHz IF amplifier constitute the RF/IF sub-module. Phase shifter fabrication using ion implantation and a self-aligned gate technique is described. Preliminary RF results obtained on such phase shifters are included.

Sokolov, V.↗
NASA NTRS1987

Low-noise cryogenic transmission line

New low-noise cryogenic input transmission lines have been developed for the Deep Space Network (DSN) at 1.668 GHz for cryogenically cooled Field Effect Transistors (FET) and High Electron Mobility Transistor (HEMT) amplifiers. These amplifiers exhibit very low noise temperatures of 5 K to 15 K, making the requirements for a low-noise input transmission line critical. Noise contribution to the total amplifier system from the low-noise line is less than 0.5 K for both the 1.668-GHz and 2.25-GHz FET systems. The 1.668-GHz input line was installed in six FET systems which were implemented in the DSN for the Venus Balloon Experiment. The 2.25-GHz input line has been implemented in three FET systems for the DSN 34-m HEF antennas, and the design is currently being considered for use at higher frequencies.

Norris, D.↗
NASA NTRS2011

Four-gate transistor analog multiplier circuit

A differential output analog multiplier circuit utilizing four G.sup.4-FETs, each source connected to a current source. The four G.sup.4-FETs may be grouped into two pairs of two G.sup.4-FETs each, where one pair has its drains connected to a load, and the other par has its drains connected to another load. The differential output voltage is taken at the two loads. In one embodiment, for each G.sup.4-FET, the first and second junction gates are each connected together, where a first input voltage is applied to the front gates of each pair, and a second input voltage is applied to the first junction gates of each pair. Other embodiments are described and claimed.

Mojarradi, Mohammad M.↗
NASA NTRS2017

Inrush Current Suppression Circuit and Method for Controlling When a Load May Be Fully Energized

A circuit and method for controlling when a load may be fully energized includes directing electrical current through a current limiting resistor that has a first terminal connected to a source terminal of a field effect transistor (FET), and a second terminal connected to a drain terminal of the FET. The gate voltage magnitude on a gate terminal of the FET is varied, whereby current flow through the FET is increased while current flow through the current limiting resistor is simultaneously decreased. A determination is made as to when the gate voltage magnitude on the gate terminal is equal to or exceeds a predetermined reference voltage magnitude, and the load is enabled to be fully energized when the gate voltage magnitude is equal to or exceeds the predetermined reference voltage magnitude.

Schwerman, Paul↗
DOE OSTI2021

Steep slope transistors with threshold switching devices

A steep-slope (SS) field effect transistor (FET) including a FET having a source region and a drain region, and a threshold switching device in direct contact with the source region or the drain region of the FET. Fabricating the steep-slope (SS) field effect transistor (FET) includes fabricating an AlGaN/GaN metal-insulator-semiconductor high electron mobility transistor (MIS-HEMT) having a source region and a drain region, depositing a first electrode layer directly on the source region or the drain region, depositing a threshold switching layer directly on the first electrode layer, and depositing a second electrode layer directly on the threshold switching layer.

Huang, Xuanqi↗
DOE OSTI2020

Detection of a multi–disease biomarker in saliva with graphene field effect transistors

Human carbonic anhydrase 1 (CA1) has been suggested as a biomarker for identification of several diseases including cancers, pancreatitis, diabetes, and Sjogren’s syndrome. However, the lack of a rapid, cheap, accurate, and easy-to-use quantification technique has prevented widespread utilization of CA1 for practical clinical applications. To this end, we present a label-free electronic biosensor for detection of CA1 utilizing highly sensitive graphene field effect transistors (G-FETs) as a transducer and specific RNA aptamers as a probe. The binding of CA1 with aptamers resulted in a positive shift in Dirac voltage V D of the G-FETs, the magnitude of which depended on target concentration. These aptameric G-FET biosensors showed the binding affinity (K D ) of ~2.3 ng/ml (70 pM), which is four orders lower than that reported using a gel shift assay. This lower value of K D enabled us to achieve a detection range (10 pg/ml - 100 ng/ml) which is well in line with the clinically relevant range. These highly sensitive devices allowed us to further prove their clinical relevance by successfully detecting the presence of CA1 in human saliva samples. In conclusion, the utilization of this label-free biosensor could facilitate the early stage identification of various diseases associated with changes in concentration of CAs.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Atomically Precise Graphene Nanoribbon Transistors with Long-Term Stability and Reliability

Atomically precise graphene nanoribbons (GNRs) synthesized from the bottom-up exhibit promising electronic properties for high-performance field-effect transistors (FETs). The feasibility of fabricating FETs with GNRs (GNRFETs) has been demonstrated, with ongoing efforts aimed at further improving their performance. However, their long-term stability and reliability remain unexplored, which is as important as their performance for practical applications. In this work, we fabricated short-channel FETs with nine-atom-wide armchair GNRs (9-AGNRFETs). We revealed that the on-state (/ ON ) current performance of the 9-AGNRFETs deteriorates significantly over consecutive full transistor on and off logic cycles, which has neither been demonstrated nor previously considered. To address this issue, we deposited a thin ~10 nm thick atomic layer deposition (ALD) layer of aluminum oxide (Al 2 O 3 ) directly on these devices. The integrity, compatibility, electrical performance, stability, and reliability, of the GNRFETs before and/or after Al 2 O 3 deposition were comprehensively studied. The results indicate that the observed decline in electrical device performance is most likely due to the degradation of contact resistance over multiple measurement cycles. We successfully demonstrated that the devices with the Al 2 O 3 layer operate well up to several thousand continuous full cycles without any degradation. Our study offers valuable insights into the stability and reliability of GNR transistors, which could facilitate their large-scale integration into practical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High performance ionic-liquid-gated air doped diamond field-effect transistors

Here we report successful fabrication of high performance ion-gated field-effect transistors (FETs) on hydrogenated diamond surface. Investigations on the hydrogen (H)-terminated diamond by Hall effect measurements shows Hall mobility as high as ~200 cm 2 V –1 s –1 . In addition we demonstrate a rapid fabrication scheme for achieving stable high performance devices useful for determining optimal growth and fabrication conditions. We achieved H-termination using hydrogen plasma treatment with a sheet resistivity as low as ~1.3 kΩ/sq. Conductivity through the FET channel is studied as a function of bias voltage on the liquid ion-gated electrode from –3.0 to 1.5 V. Stability of the H-terminated diamond surface was studied by varying the substrate temperature up to 350 °C. It was demonstrated that the sheet resistance and carrier densities remain stable over 3 weeks in ambient air atmosphere even at substrate temperatures up to 350 °C, whereas increasing temperature beyond this limit has effected hydrogenation. This study opens new avenues for carrying out fundamental research on diamond FET devices with ease of fabrication and high throughput.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Bottom‐Up Synthesized Nanoporous Graphene Transistors

Abstract Nanoporous graphene (NPG) can exhibit a uniform electronic band gap and rationally‐engineered emergent electronic properties, promising for electronic devices such as field‐effect transistors (FETs), when synthesized with atomic precision. Bottom‐up, on‐surface synthetic approaches developed for graphene nanoribbons (GNRs) now provide the necessary atomic precision in NPG formation to access these desirable properties. However, the potential of bottom‐up synthesized NPG for electronic devices has remained largely unexplored to date. Here, FETs based on bottom‐up synthesized chevron‐type NPG (C‐NPG), consisting of ordered arrays of nanopores defined by laterally connected chevron GNRs, are demonstrated. C‐NPG FETs show excellent switching performance with on–off ratios exceeding 10 4 , which are tightly linked to the structural quality of C‐NPG. The devices operate as p‐type transistors in the air, while n‐type transport is observed when measured under vacuum, which is associated with reversible adsorption of gases or moisture. Theoretical analysis of charge transport in C‐NPG is also performed through electronic structure and transport calculations, which reveal strong conductance anisotropy effects in C‐NPG. The present study provides important insights into the design of high‐performance graphene‐based electronic devices where ballistic conductance and conduction anisotropy are achieved, which could be used in logic applications, and ultra‐sensitive sensors for chemical or biological detection.

Mutlu, Zafer↗
DOE OSTI2022

Intrinsic (Trap‐Free) Transistors Based on Epitaxial Single‐Crystal Perovskites

Abstract The first experimental realization of the intrinsic (not dominated by defects) charge conduction regime in lead‐halide perovskite field‐effect transistors (FETs) is reported. The advance is enabled by: i) a new vapor‐phase epitaxy technique that results in large‐area single‐crystalline cesium lead bromide (CsPbBr 3 ) films with excellent structural and surface properties, including atomically flat surface morphology, essentially free from defects and traps at the level relevant to device operation; ii) an extensive materials analysis of these films using a variety of thin‐film and surface probes certifying the chemical and structural quality of the material; and iii) the fabrication of nearly ideal (trap‐free) FETs with characteristics superior to any reported to date. These devices allow the investigation of the intrinsic FET and (gated) Hall‐effect carrier mobilities as functions of temperature. The intrinsic mobility is found to increase on cooling from ≈30 cm 2 V −1 s −1 at room temperature to ≈250 cm 2 V −1 s −1 at 50 K, revealing a band transport limited by phonon scattering. Establishing the intrinsic (phonon‐limited) mobility provides a solid test for theoretical descriptions of carrier transport in perovskites, reveals basic limits to the technology, and points to a path for future high‐performance perovskite electronic devices.

36 MATERIALS SCIENCE↗