Search NASA⌕ Search

SEARCH · Search NASA

Results for “In-Situ Microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

The Spatial Distribution of Soluble Organic Matter and Their Relationship to Minerals in the Asteroid (162173) Ryugu

We performed in-situ analysis on a ~1 mm-sized grain A0080 returned by the Hayabusa2 spacecraft from near-Earth asteroid (162173) Ryugu to investigate the relationship of soluble organic matter (SOM) to minerals. Desorption electrospray ionization-high resolution mass spectrometry (DESI-HRMS) imaging mapped more than 200 CHN, CHO, CHO–Na (sodium adducted), and CHNO soluble organic compounds. A heterogeneous spatial distribution was observed for different compound classes of SOM as well as among alkylated homologues on the sample surface. The A0080 sample showed mineralogy more like an Ivuna-type (CI) carbonaceous chondrite than other meteorites. It contained two different lithologies, which are either rich (lithology 1) or poor (lithology 2) in magnetite, pyrrhotite, and dolomite. CHN compounds were more concentrated in lithology 1 than in lithology 2; on the other hand, CHO, CHO–Na, and CHNO compounds were distributed in both lithologies. Such different spatial distribution of SOM is likely the result of interaction of the SOM with minerals, during precipitation of the SOM via fluid activity, or could be due to difference in transportation efficiencies of SOMs in aqueous fluid. Organic-related ions measured by time-of-flight secondary ion mass spectrometry (ToF–SIMS) did not coincide with the spatial distribution revealed by DESI-HRMS imaging. This result may be because the different ionization mechanism between DESI and SIMS, or indicate that the ToF–SIMS data would be mainly derived from methanol-insoluble organic matter in A0080. In the Orgueil meteorite, such relationship between altered minerals and SOM distributions was not observed by DESI-HRMS analysis and field-emission scanning electron microscopy, which would result from differences of SOM formation processes and sequent alteration process on the parent bodies or even on the Earth. Alkylated homologues of CHN compounds were identified in A0080 by DESI-HRMS imaging as observed in the Murchison meteorite, but not from the Orgueil meteorite. These compounds with a large C number were enriched in Murchison fragments with abundant carbonate grains. In contrast, such relationship was not observed in A0080, implying different formation or growth mechanisms for the alkylated CHN compounds by interaction with fluid and minerals on the Murchison parent body and asteroid Ryugu.

Ryugu↗
DOE OSTI2026

In-situ synchrotron X-ray investigation of phase evolution in gas atomized powder enabling manufacturing of nanoscale oxide-dispersion strengthened ferritic steels

Here, we present an investigation of Fe-14Cr-3W-0.4Y-0.4Zr-0.18Ti (wt.%) as a reduced-activation oxide-dispersion strengthened (ODS) ferritic steel, an alternative to the “14YWT” structural alloys designed for nuclear energy applications. Gas atomization reaction synthesis (GARS) was used to produce these Zr-modified powders with a non-equilibrium (metastable) phase that enable a heat treatment (delayed) route for producing nanoscale oxide-dispersion strengthening. In situ synchrotron X-ray diffraction and transmission electron microscopy were used to analyze phase evolution as a function of temperature and time, revealing formation of highly dispersed oxide nanoprecipitate phases at temperatures above those needed for powder consolidation and shaping of components. This would allow fabrication of net-shape parts using conventional powder-processing methods prior to thermal activation of a reaction producing nanocrystalline Y-(Ti, Zr)-O particles, with a size of 20 ± 7 nm. These results can inform processing of tubes, cladding, sheets, and plates for use in advanced fission and fusion reactors.

In-situ synchrotron X-ray diffraction↗
DOE OSTI2026

Strong Effect of Nonpolar Solvent Molecular Structure on CdSe Nanoplatelet Stacking

We report a drastic difference in stacking behavior of oleic acid-stabilized 4-monolayer (4 ML) CdSe nanoplatelets (NPLs) in toluene and methylcyclohexane (MCH), two nonpolar solvents that differ in the conformational flexibility of their molecules. Using liquid cell transmission electron microscopy (TEM) and small angle scattering (SAXS) techniques, we show that NPLs form microns-long ribbons consisting of 4 ML CdSe NPLs in toluene, the solvent widely used to form stable colloidal solutions of a broad range of quasi-spherical nanoparticles. In contrast, 4 ML CdSe NPLs are well dispersed in MCH. The difference in stacking behavior of NPLs in toluene and MCH suggests that the conformational flexibility of the solvent molecules, such as the ability to adopt multiple chair conformations, modulates nanoplatelet interactions. Molecular dynamics (MD) simulations reveal that solvent molecules subtly alter the structure of the organic ligand shell. These solvent-dependent changes propagate to the inorganic core, modulating the degree of CdSe nanoplatelet (NPL) twisting and, consequently, the properties of the nanoparticles. We show that toluene better solvates oleate ligands while MCH induces a bimodal oleate span distribution, which can lead to increased solubility of CdSe NPLs. In addition, the solvent can also influence the inorganic core, which, in turn, can modify the nanoparticle properties. We demonstrate that destabilization of toluene solution containing ribbons of 4 ML CdSe NPLs without CdS shells results in the formation of NPL assemblies with amplified spontaneous emission (ASE) with a low threshold of 14 µJ cm−2 that is comparable with that of CdSe/CdS core/shell NPLs. Our results emphasize that the solvent plays a major role in mediating interactions between NPLs and hence their processability for fabrication of functional structures.

CdSe↗
DOE OSTI2024

Nanotwinned alloys under high pressure

Nanotwinned alloys are of interest due to their high strength and ductility, but twin boundaries may not be stable under shear. Computational studies indicate that high hydrostatic pressure may suppress detwinning mechanisms. Here, in this study, we investigate the microstructural changes of nanotwinned-nanocrystalline copper-nickel and Inconel 725 alloys under quasi-hydrostatic pressures up to 50 gigapascals (GPa). The alloys are compressed in a diamond anvil cell. In-situ x-ray diffraction (XRD) and ex-situ transmission electron microscopy (TEM) were employed to monitor microstructural changes. Twin boundary deformation and grain growth occur at 11.4 GPa quasi-hydrostatic pressure in the copper-nickel alloy. Molecular dynamics (MD) simulations reveal that hydrostatic pressure causes elevated local shear stress at grain boundaries, which leads to atomic rearrangements. A superposition of hydrostatic and deviatoric pressures lead to partial dislocation mediated twin boundary migration. In contrast, the Inconel 725 alloy showed stable twin and grain boundaries up to a quasi-hydrostatic pressure of 12.7 GPa. Texture, high solid solution strengthening, and low stacking fault energy are hypothesized to the enhanced microstructural stability in Inconel 725.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Quantification of grain rotation in bulk nanostructured copper via in situ heating white beam synchrotron X-ray diffraction

Grain rotation during microstructural relaxation under heating is conventionally studied extensively through transmission electron microscopy and simulations. However, there is a shortage in examining grain rotations at larger length and volume scales in bulk materials. It is critical to understand the thermal stability of bulk nanostructured metals, since those enhanced mechanical properties have been well recognized. Here, this study aimed to employ a white beam microdiffraction X-ray technique under in situ heating from 300 K to 1073 K at 12 K/min on a nanostructured copper processed by high-pressure torsion, yielding an initial grain size of ∼260 nm before the heating. Evaluation across a wide range of temperatures reveals transition temperatures associated with microstructural relaxation processes. By tracking separate Laue diffraction peaks stemming from individual grains, changes in their orientations can be estimated and quantified. This approach becomes particularly effective when the number of grains within the probed volume is reasonably small. At temperatures above 940 K, about 7.5 % of Cu grains are rotating at speeds of ∼2 × 10 –3 °/s. The radial direction of the disk specimen is found to be the preferred direction of grain rotation, with the rotation axis along the shear direction. Further analysis found no correlation between peak intensity and peak size, related to grain sizes and deviatoric strain, respectively, with rotation conditions or speed. These findings demonstrate that the diffraction technique utilizing white beam X-rays is a complementary and novel characterization tool for understanding microstructural evolution, especially in grain rotations, of bulk crystalline materials.

Grain orientation↗
DOE OSTI2026

Emerging hierarchical dislocation structures: Insights from scanning electron microscopy-electron backscatter diffraction in situ tensile testing and multifractal analysis

Understanding the evolution of dislocation structures during plastic deformation is critical for predicting the mechanical performance of metallic materials. In this work, we applied in situ scanning electron microscopy/electron backscatter diffraction tensile testing combined with multifractal (MF) analysis to assess deformation-induced dislocation structure evolution in solution-annealed 304 L stainless steel, both in its as-received and neutron-irradiated states (5.4 displacements per atom). The analysis of kernel average misorientation patterns revealed the formation of hierarchical dislocation arrangements that exhibit clear MF scaling behavior. Despite pronounced visual differences between nonirradiated and irradiated specimens—most notably, the appearance of dislocation channels after irradiation—the singularity spectra suggest that both conditions give rise to similar underlying hierarchical structures. MF analysis provides a quantitative measure of the spatial complexity and self-organization of dislocation patterns, highlighting the accelerated emergence and evolution of the dislocation structures in irradiated polycrystalline materials, as well as the limitation of their spatial extent. The findings indicate that irradiation not only modifies microstructure but also alters correlation-driven dislocation organization. More generally, they demonstrate that MF analysis is a powerful tool for probing mesoscale deformation mechanisms.

Dislocation structures↗
DOE OSTI2026

In-Situ Visualization of a Growing Brittle Crack in Aluminum Oxynitride Using Synchrotron X-Rays and the Double-Cleavage Drilled Compression Geometry

Brittle fracture is difficult to study in situ due to the speed of a growing crack and the often-catastrophic nature of failure in brittle materials. As a result, the influence of microstructural considerations, such as orientation, grain boundary locations, and strain field, on the crack path remains poorly understood. Presented in this study is a method addressing this knowledge gap, which utilizes the double-cleavage drilled compression geometry to achieve quasi-stable fracture in aluminum oxynitride (AlON). Synchrotron X-ray micro-computed tomography is used to characterize the crack shape and length, while high-energy diffraction microscopy provides information on the strains, orientations, and shapes of grains in the microstructure surrounding the crack tip. During testing, the crack grew in discrete and irregular jumps while the fracture toughness falls within reported ranges. The crack in AlON is found to have no greater tendency to crack intergranularly as compared to transgranularly, and grains which are cracked transgranularly do not display a trend in orientation or stress when compared to those around which the crack followed a grain boundary. The high resolution of the crack path and microstructural data provides a path forward for modeling and understanding 3D brittle fracture.

Gorske, Sara F.↗
DOE OSTI2025

Inkless, dry printing nanographene via in-Situ Coordinated laser ablation and sintering processes

Printing carbon, such as graphene and other carbon structures, for flexible and printed electronics currently relies on either ink-based printing, laser-induced forward transfer (LIFT), or laser-induced graphitization (LIG) to convert carbon-rich precursor materials, such as polymers, to graphene-like carbon structures. Liquid inks contain toxic solvents, surfactants, and stabilizing additives that degrade electrical conductivity and require high-temperature post-processing. On the other hand, LIG is limited by the substrate. Here, this study introduces an additive manufacturing method for dry-printing carbon nanomaterials, ranging from amorphous carbon to crystalline graphene-like structures, on various substrates. The system utilizes laser ablation of a solid graphite target to create pure carbon nanoparticles in situ and on demand. An inert gas carries the nanoparticles onto the substrate, where they can be deposited either as amorphous structures or laser-sintered in real time to form various graphitic structures. The study of laser processing parameters, specifically fluence and pulse repetition frequency, revealed three unique regimes of nanostructure evolution that influence the morphological and electrical properties of these printed structures. Raman spectroscopy confirmed graphitization with a resistivity slightly higher than that of the bulk graphite target. The conductivity/resistivity could be tuned as a function of sintering laser power. Scanning transmission electron microscopy (STEM) revealed that turbostratic nanographene formed with an interlayer spacing of 0.40 nm. Despite ink-based printing methods, such as screen printing, inkjet printing (IJP), and aerosol jet printing (AJP), this eco-friendly and green manufacturing technique could eliminate toxic chemicals, reduce environmental impact, and enable single-step fabrication of carbon-based devices for applications in wearable sensors, energy storage, flexible electronics, and Internet of Things (IoT) devices.

Additive nanomanufacturing↗
DOE OSTI2025

In situ high-temperature Raman spectroscopy for online EAF slag analysis

Real-time monitoring of slag chemistry is critical for optimizing Electric Arc Furnace (EAF) steelmaking operations, where dynamic variations in slag composition directly influence slag foaming, refractory degradation, and thermal efficiency. Conventional techniques such as X-ray fluorescence (XRF), Fourier-transform infrared (FTIR), and scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM-EDS) are commonly used to analyze slag composition, but their offline nature and equipment constraints limit their applicability for online monitoring in harsh industrial environments. To address this challenge, we present an in situ, high-temperature analytical approach that integrates Raman spectroscopy with a custom designed fiber-optic probe for real-time slag characterization at 1550 °C. The system enables non destructive spectral acquisition from molten slags, providing molecular-level insights into silicate polymerization and iron oxidation states. Eight synthetic slag samples were evaluated, and key Raman features—such as Q n silicate units and FeO₄/FeO₆ coordination environments—were identified and quantitatively correlated with slag basicity and Fe₂O₃ content. The results demonstrate agreement between Raman spectral ratios and bulk slag chemistry, validating the method’s capability to track compositional and structural changes under molten temperature. This work establishes the feasibility of deploying fiber-optic Raman probe for online EAF slag monitoring and highlights their potential to support closed-loop control strategies, thereby enhancing process stability, refractory protection, and steel quality in industrial steelmaking applications.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Microstructural evolution of compositionally complex solid-solution alloys under in-situ dual-beam irradiation

Here, this work attempts to link the microstructural evolution of single-phase compositionally complex alloy (CCA) compositions under dual-beam irradiation to their Mn-content via the stacking-fault energy (SFE) and vacancy migration energies. Two alloys, Cr 18 Fe 27 Mn 27 Ni 28 and Cr 15 Fe 35 Mn 15 Ni 35 , along with less compositionally complex pure Ni and Fe 56 Ni 44 binary were irradiated at 500 and 600 °C under dual-beam 1 MeV Kr 2+ and 16 keV He + heavy-ions up to 7 displacements per atom (dpa) with a He/dpa ratio of 0.75 %/dpa using in situ transmission electron microscopy (TEM). Due to the bubble-stabilizing effect of implanted He, bubbles were observed in all irradiations, and populations of faulted interstitial loops were characterized in Cr 18 Fe 27 Mn 27 Ni 28 and Cr 15 Fe 35 Mn 15 Ni 35 . A reduction in swelling was observed in the two CCAs compared to pure Ni and Fe 56 Ni 44 . Although swelling increased from 500 to 600 °C in Fe 56 Ni 44 , Cr 15 Fe 35 Mn 15 Ni 35 and Cr 18 Fe 27 Mn 27 Ni 28 both swelled slightly more at 500 °C. This was attributed to the difference in vacancy mobility, stronger pinning effect of vacancies on He, and the sink strength of faulted dislocation loops. Faulted interstitial loops nucleated with a higher number density and dislocation line density in Cr 15 Fe 35 Mn 15 Ni 35 at both temperatures, and at 600 °C in both materials. The differences in faulted loop population and temperature effect on swelling are correlated to the Mn-content and the measured SFE (20.2 ± 6.7 mJ/m 2 for Cr 18 Fe 27 Mn 27 Ni 28 and 9.2 ± 3.4 mJ/m 2 for Cr 15 Fe 35 Mn 15 Ni 35 ).

36 MATERIALS SCIENCE↗
DOE OSTI2026

Machine learning pipeline for denoising low signal-to-noise ratio and out-of-distribution transmission electron microscopy datasets

High-resolution transmission electron microscopy (HRTEM) is crucial for observing material’s structural and morphological evolution at Angstrom scales, but the electron beam can alter these processes. Devices such as CMOS-based direct-electron detectors operating in electron-counting mode can be utilized to substantially reduce the electron dosage. However, the resulting images often lead to a low signal-to-noise ratio, which requires frame integration that sacrifices temporal resolution. Several machine learning (ML) models have been recently developed to successfully denoise HRTEM images. Yet, these models are often computationally expensive, and their inference speeds on GPUs are outpaced by the imaging speed of advanced detectors, precluding in situ analysis. Furthermore, the performance of these denoising models on datasets with imaging conditions that deviate from the training datasets has not been evaluated. To mitigate these gaps, we propose a new self-supervised ML denoising pipeline specifically designed for time-series HRTEM images. This pipeline integrates a blind-spot convolution neural network with pre-processing and post-processing steps, including drift correction and low-pass filtering. Results demonstrate that our model outperforms various other ML and non-ML denoising methods in noise reduction and contrast enhancement, leading to improved visual clarity of atomic features. Additionally, the model is drastically faster than U-Net-based ML models and demonstrates excellent out-of-distribution generalization. The model’s computational inference speed is in the order of milliseconds per image, rendering it suitable for application in in-situ HRTEM experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Synergistic effects of Pd single atoms and nanoclusters boosting SnO 2 gas sensing performance

Tin(IV) oxide-supported Pd is a promising heterogenous catalyst for CO oxidation relevant for environmental cleanup reactions. In this study, an atomically dispersed Pd catalyst on SnO 2 (ADC Pd/SnO 2 ) hybrid material is successfully synthesized via a straightforward wet chemistry method and is found to exhibit superior performance toward CO sensing. Ex situ EXAFS analysis confirms the formation of single Pd atoms and small Pd nanoclusters stabilized on the SnO 2 (110) surface. Further, the material exhibits high efficiency in generating adsorbed O 2 - as well as high activity in catalyzing CO oxidation at low temperatures, resulting in exceptional sensitivity and selectivity toward CO in comparison to pure SnO 2 and Pd nanoparticles loaded on SnO 2 respectively. In situ FTIR measurements unravel CO adsorption kinetics on ADC Pd/SnO 2 under reaction conditions, and a possible sensing mechanism is put forth in which CO is transformed into CO 2 by reaction with active oxygen species; and concurrently, carbon-related species (bicarbonates and carbonates) are formed and decomposed into CO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Fe-single atom catalysts facilitate fast electron transfer with MoS 2 /SnS 2 cathodes in lithium–sulfur batteries

Lithium–sulfur batteries (LSBs) emerge as promising next-generation energy storage systems offering cost-effectiveness, environmental friendliness, and high theoretical energy density. The practical implementation of LSBs faces significant hindrances due to the shuttle effect and sluggish redox reactions. To address these challenges, single-atom catalyst (SAC) based combination materials from d-block elements can offer increased active catalytic sites, rapid charge transfer, accelerated electron migration, and fast sulfur redox conversion kinetics of lithium polysulfides (LiPSs). In this study, we fabricated three different LSB cathodes: pure S, S@MoS 2 /SnS 2 , and S@Fe–MoS 2 /SnS 2 . These cathodes were then used to explore the cycle life, capacity, rate capability, and redox kinetic reactions of LiPSs while assessing the influence of Fe-SACs on their performance. As a result, LSBs with S@Fe–MoS 2 /SnS 2 cathodes demonstrate an extended cycle life of 1000 cycles at a C-rate of 0.2C, maintaining a capacity close to 500 mA h g −1 , the highest initial discharge capacity of 1622 mA h g −1 and 1066 mA h g −1 at 0.05C and 0.2C, and excellent rate capabilities of 708 mA h g −1 and 558 mA h g −1 at 1C and 2C, respectively. The synergistic effect of the Fe-SAC-based combination cathode (S@Fe–MoS 2 /SnS 2 ) creates plentiful adsorptive and highly active catalytic sites, resulting in substantially enhanced capacity for adsorbing soluble long-chain LiPSs. This facilitates ultra-fast redox kinetics, surpassing the performance of the S@MoS 2 /SnS 2 and pure S cathodes. In the ex situ analysis, results from powder X-ray diffraction (XRD) to observe the new phase, soft X-ray absorption spectroscopy (XAS) to investigate the electronic structure, and hard X-ray photoelectron microscopy (HAXPES) with different energies (900 eV, 2000 eV, and 6000 eV) to track the chemical-state evolution of Fe-SACs in MoS 2 /SnS 2 cathodes displayed notable electrochemical reversibility involving S 8 ⇄ LiPSs ⇄ Li 2 S conversion even after 1000 cycles. Additionally, in situ, operando Raman analysis can unveil a novel catalytic mechanism of Fe-SACs in MoS 2 /SnS 2 “facilitating rapid electron transfer” during the discharge and charge processes of LSBs involving the conversion of S 8 ⇄ long-chain LiPSs ⇄ Li 2 S 2 /Li 2 S. This study elucidates the working mechanism of Fe-SAC cathodes, offering insights into overcoming the shuttle effect and facilitating sulfur redox kinetics to advance commercial LSBs.

36 MATERIALS SCIENCE↗
DOE OSTI2026

FY26 Progress Report on the Operation of the Activated Materials Laboratory at the Advanced Photon Source as a Nuclear Science User Facilities Partner Facility

The Activated Materials Laboratory (AML), located in the Long Beamline Building of the Advanced Photon Source (APS) at Argonne National Laboratory (ANL), provides a centralized radiological capability for preparing, handling, and supporting synchrotron experiments on activated materials. As a Nuclear Science User Facilities (NSUF) partner facility, the AML enables the receipt of radioactive shipments, open-form sample handling, encapsulation, transport of specimens to and from APS beamlines, and experimentation with dedicated equipment. The partnership includes the APS 1-ID and 20-ID beamlines, which provide high-energy x-ray scattering, tomography, and diffraction microscopy techniques for ex-situ, in-situ, and grainresolved three-dimensional (3D) characterization. All samples supported through the AML and partner beamlines must meet radiological limits of less than 100 mrem/h at 30 cm. This FY26 progress report summarizes the first full year of AML operations as an NSUF partner facility and highlights progress in both user support and capability development. By the end of FY26, the AML had received a total of 10 NSUF-awarded projects, including 2 Consolidated Innovative Nuclear Research (CINR), 7 Rapid Turnaround Experiment (RTE), and 1 Super RTE projects. Beamtime was fully delivered for 3 RTE projects and partially delivered for 1 CINR project, demonstrating successful workflows for receipt, encapsulation, beamline transfer, and radiological experiment execution. These efforts demonstrated safe radiological experiments at APS beamlines for samples with dose rates above the historical 5 mrem/h threshold and now up to 100 mrem/h at 30 cm, marking an important milestone for neutron-irradiated materials research. During FY26, the AML also expanded its experimental capabilities. A Psylotech xTS load frame with in-grip rotation was deployed for room-temperature mechanical testing with threedimensional x-ray characterization during interrupted loading. A Linkam TS1500V vacuum heater was commissioned for thermally driven studies, and temperature calibration experiments were performed to establish specimen-relevant thermal profiles. In parallel, a customized split-tube furnace for high-temperature mechanical testing entered commissioning, and initial work began on robotic sample handling to reduce worker dose and improve operational efficiency. Data workflow and beamline operations continued to mature. Together, these developments demonstrate that the AML is becoming a unique national resource for safe, efficient, and scientifically advanced characterization of activated materials at the APS.

Zhang, Xuan↗
NASA NTRSDate not supplied

Low-Temperature Production of Cosmic Grains Analogs From Gas-Phase Molecular Precursors with the NASA Ames' COSmIC Facility

Complex carbon molecules and ions are ubiquitous in space and form the building blocks of carbonaceous cosmic dust grains, ultimately contributing to the formation of planets. Here, we report the first experimental investigations of the low temperature chemical pathways leading to the production of cosmic grain analogs from gas phase molecular precursors in order to better understand the evolution of cosmic carbon. The experiments were performed using the COsmic SImulation Chamber (COSmIC) to generate and characterize grains formed from gas phase precursors under controlled conditions representative of astrophysical environments [1]. Using COSmIC, it is possible to investigate the evolution of cosmic carbon from the formation of neutral and ionized gas phase hydrocarbons and PAHs [2], to carbon grains [3, 4]. This is achieved by using a discharge nozzle to (1) produce an adiabatic jet expansion and cool down Ar-hydrocarbon/PAH gas mixtures to astrophysically relevant temperature (150 K) before inducing chemistry by generating a plasma discharge in the stream of the expansion. This plasma-induced chemistry results in the formation of complex molecules and solid particles, analogs of cosmic grains. Solid grains are produced in-situ in the plasma expansion, carried by the accelerated gas in the expansion, and collected on substrates placed a few centimeters downstream of the electrodes. The results of a preliminary solid phase ex-situ analysis of cosmic grain analogs produced at low temperature in COSmIC from gas mixtures including molecular precursors of cosmic carbon grains, i.e., such as CH4 and C2H2 found in circumstellar ejecta of late C stars [3] as well as PAHs ubiquitously detected in IR emission bands seen in galactic and extragalactic environments [4] will be discussed. Scanning Electron Microscopy imaging was used to provide insight on the morphology and growth structure of the grains produced in COSmIC, and to investigate how the precursors used to produce the grains affect these parameters [3]. Laser desorption mass spectrometry was used to identify the molecules making up the main structures within the condensed grains [4]. NIR to FIR optical properties are characterized to provide critical information (functional groups, optical constants) to the scientific community, for use in radiative transfer models in particular, and to help decipher and enhance the return data from space observations.

F. Salama↗
NASA NTRSDate not supplied

In-Situ Alloying of GRCop-42 via Additive Manufacturing: Precipitate Analysis

GRCop-42, a Cu-4at% Cr-2at% Nb alloy, was designed as a high temperature, high strength, high heat flux material for rocket engine combustion chamber liners by NASA Glenn Research Center. In situ alloying of GRCop-42 (ISGRCop-42) using powder bed fusion (PBF) additive manufacturing (AM) takes elemental powders of Cu, Cr, and Nb to be introduced into the PBF environment and develop the GRCop alloy while simultaneously building an AM component. Elemental powders were milled together prior to printing in an effort to facilitate the alloying process. Success of the in situ alloying process may provide lower cost, faster lead times, alloying optimization, and more design freedom in the development of regeneratively-cooled rocket propulsion systems. Evaluation of the ISGRCop-42 was conducted using a phase extraction procedure to isolate the Cr2Nb precipitates from the pure Cu matrix. The isolated precipitates were then examined using x-ray powder diffraction (XRD), scanning electron microscopy (SEM), and energy dispersion spectroscopy (EDS). It was found that ISGRCop-42 successfully and repeatedly formed Cr2Nb at a yield as high as 89% of potential Cr2Nb. Further, it was identified that the preparation of the powder was the most influential factor in alloying success, and the second most influential factor was the laser power.

In Situ alloying↗
NASA NTRSDate not supplied

The Additive Manufacturing Moment Measure - A Parallel Computation Technique for Determining Build Variance in the Laser Powder Bed Fusion Process

Additive manufacturing (AM) has unique process attributes that facilitate the creation of optimized, complex, and unique parts for aerospace applications. However, the multi-scale and complicated building process for AM parts can cause unexpected build conditions that result in microstructural variability within the deposited material. The need for richer datasets and computational modeling capabilities to improve AM process reliability is a consequence of this microstructural variability. A computational approach, referred to as the Additive Manufacturing Moment Measure (AM3), addresses this need by leveraging the way AM processes fuse material in precise, incremental steps. During the layering sequence, each previous step contributes to the condition of the current step at the center of the heat source. The precise steps can be selected to systematically create a time-space point field with co-located machine input and in-situ sensor data. The sequential nature of the AM process, coupled with nearest neighbor calculations, allows for a fully parallel computation for part-scale build profile analysis. The AM3 concept introduced here enables part-scale assessment directly from build files and in-situ process monitoring sensors alike. The AM moment measures were calculated for build point fields and compared with co-located in-situ and ex-situ nondestructive evaluation and optical microscopy observations. These comparisons permit a better understanding of how the sequential process actions can affect the quality of a laser powder bed fusion (LPBF) build. Details of the AM3technique will be discussed and compared to measured LPBF part characteristics. The AM3 results indicate a strong potential to advance the qualification process for aerospace applications.

Additive Manufacturing↗
NASA NTRSDate not supplied

In-Situ Process Monitoring, Synchronization, and Mapping Laser Powder Bed Fusion Builds of Ti6Al4V

The use of in-situ process monitoring is of interest to lower the cost of inspection for the qualification of laser powder bed fusion (LPBF) parts. Precise monitoring of the LPBF-AM build process constitutes a multi-scale and multi-discipline task. There are several significant challenges to the in-situ approach: the synchronization of sensor signals to process steps, the physical interpretation and classification of sensor signals, managing very large datasets, and comparing the inputs with the observed monitoring signals. At NASA Langley Research Center, a configurable architecture additive testbed has been developed to monitor the build process with synchronized sensors. The philosophy and method adopted for the synchronization of the cameras with laser power & position Ti-6Al-4V LPBF are described. The synchronized in-situ monitoring signals are compared with ex-situ nondestructive inspection and optical microscopy observations. Such comparisons permit a better understanding of how the sequential process actions of LPBF-AM can affect build quality.

Laser Powder Bed Fusion↗