SEARCH · Search NASA

Results for “Interface correction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1972

OMEGA timing receiver, design and system test

The design of a two frequency OMEGA Timing Receiver is discussed. The receiver tracks the arrival time of the signals by precise phase matching at the receiving antenna. Provision is made for inserting a propagation delay correction for each signal path. Time is measured as the difference between the zero crossing coincidence of the corrected signals and the local time. This number is displayed on the front panel in microseconds. The receiver can also function as a precise phase tracking receiver for collection of propagation data essential to augmenting the propagation corrections. All phase and time information is made available in a BCD format for flexibility in interfacing with other equipment. Results of preliminary tests using experimental transmissions are given. Preliminary results indicate time may be transferred by this technique to an accuracy of a few microseconds.

Wilson, J. J.↗

NASA NTRS1978

Advanced instrumentation concepts for environmental control subsystems

Design, evaluation and demonstration of advanced instrumentation concepts for improving performance of manned spacecraft environmental control and life support systems were successfully completed. Concepts to aid maintenance following fault detection and isolation were defined. A computer-guided fault correction instruction program was developed and demonstrated in a packaged unit which also contains the operator/system interface.

Yang, P. Y.↗

NASA NTRS1988

Integration of a computerized two-finger gripper for robot workstation safety

A microprocessor-based controller has been developed that continuously monitors and adjusts the gripping force applied by a special two-finger gripper. This computerized force sensing gripper system enables the endeffector gripping action to be independently detected and corrected. The gripping force applied to a manipulated object is real-time monitored for problem situations, situations which can occur during both planned and errant robot arm manipulation. When unspecified force conditions occur at the gripper, the gripping force controller initiates specific reactions to cause dynamic corrections to the continuously variable gripping action. The force controller for this intelligent gripper has been interfaced to the controller of an industrial robot. The gripper and robot controllers communicate to accomplish the successful completion of normal gripper operations as well as unexpected hazardous situations. An example of an unexpected gripping condition would be the sudden deformation of the object being manipulated by the robot. The capabilities of the interfaced gripper-robot system to apply workstation safety measures (e.g., stop the robot) when these unexpected gripping effects occur have been assessed.

Sneckenberger, John E.↗

NASA NTRS2002

A methodology for modeling the mechanical interaction between a reaction wheel and a flexible structure

This paper presents a modeling methodology used to predict the performance of a flexible structure, such as a space telescope, in the presence of an on-board vibrational disturbance source, such as a reaction wheel assembly (RWA). Both decoupled and coupled analysis methods are presented. The decoupled method relies on blocked RWA disturbances, measured with the RWA hardmounted to a rigid surface. The coupled method corrects the blocked RWA disturbance boundary conditions using "force filters," which depend on estimates of the interface accelerances of the RWA and space-craft. Both methods were validated on the Micro-Precision Interferometer testbed at the Jet Propulsion Laboratory. Experimental results are encouraging, indicating that both methods provide sufficient accuracy compared to measured values; however, the coupled method provides the best results when the gyroscopic nature of the spinning RWA is captured in the RWA accelerance model. Additionally, the RWA disturbance cross spectral density terms are found to be influential.

vibration↗

NASA NTRSDate not supplied

Copernicus-LinCov (COPCOV) Software Integration in Support of Robust Trajectory Optimization

Robust trajectory optimization is the process of optimizing a trajectory while accounting for system uncertainty due to a variety of potential error sources. This work highlights the development and features of a novel tool known as CopCov to support robust trajectory optimization efforts. CopCov acts as an interface between Copernicus, a generalized trajectory design and optimization tool, and LinCov, a linear covariance analysis tool. By having a direct interface between these two software packages, Copernicus can receive covariance information from LinCov through a direct feedback loop, thus enabling optimization of a trajectory that is robust to trajectory dispersions and navigation errors. This paper details the architecture of CopCov and its flexibility to operate under varying configurations, including with both tools running locally or alternatively with the tools communicating via a remote connection. Additionally, the CopCov tool is demonstrated on a simple Hohmann transfer reference trajectory with varying numbers of Trajectory Correction Maneuvers (TCMs) and varying problem formulations. This example scenario is used to highlight how the inclusion of the CopCov interface affects burn placement of both major burns and minor burns (i.e., TCMs) in the optimized solution. Results are compared against analytical solutions and against a Genetic Algorithm (GA) optimizer for independent verification and validation.

Copernicus↗

NASA NTRS2002

Hybrid Verification of an Interface for an Automatic Landing

Modern commercial aircraft have extensive automation which helps the pilot by performing computations, obtaining data, and completing procedural tasks. The pilot display must contain enough information so that the pilot can correctly predict the aircraft's behavior, while not overloading the pilot with unnecessary information. Human-automation interaction is currently evaluated through extensive simulation. In this paper, using both hybrid and discrete-event system techniques, we show how one could mathematically verify that an interface contains enough information for the pilot to safely and unambiguously complete a desired maneuver. We first develop a nonlinear, hybrid model for the longitudinal dynamics of a large civil jet aircraft in an autoland/go-around maneuver. We find the largest controlled subset of the aircraft's flight envelope for which we can guarantee both safe landing and safe go-around. We abstract a discrete procedural model using this result, and verify a discrete formulation of the pilot display against it. An interface which fails this verification could result in nondeterministic or unpredictable behavior from the pilot's point of view.

Oishi, Meeko↗

NASA NTRS1973

Velocity control propulsion subsystem of the Radio Astronomy Explorer satellite for Goddard Space Flight Center

The Velocity Control Propulsion Subsystem (VCPS) was designed the propulsion required for trajectory and lunar orbit corrections of the spacecraft. A GFE clamp assembly physically attaches the VCPS to the spacecraft and the unit is ejected after completing the required corrections. The VCPS is physically and functionally separated from the spacecraft except for the electrical and telemetry interfaces. A GFE transtage provides the superstructure on which the VCPS is assembled. The subsystem consists of two 5 foot pound rocket engine assemblies, 4 propellant tanks, 2 latching valves, 2 fill and drain valves, a system filter, pressure transducer, gas and propellant manifolds and electrical heaters and thermostats. The RAE-B VCPS program covered the design, manufacture and qualification of one subsystem. This subsystem was to be manufactured, subjected to qualification tests; and refurbished, if necessary, prior to flight. The VCPS design and test program precluded the need for refurbishing the subsystem and the unit was delivered to GSFC at the conclusion of the program.

Braught, W.↗

NASA NTRS1982

Photogrammetry of the Viking Lander imagery

The problem of photogrammetric mapping which uses Viking Lander photography as its basis is solved in two ways: (1) by converting the azimuth and elevation scanning imagery to the equivalent of a frame picture, using computerized rectification; and (2) by interfacing a high-speed, general-purpose computer to the analytical plotter employed, so that all correction computations can be performed in real time during the model-orientation and map-compilation process. Both the efficiency of the Viking Lander cameras and the validity of the rectification method have been established by a series of pre-mission tests which compared the accuracy of terrestrial maps compiled by this method with maps made from aerial photographs. In addition, 1:10-scale topographic maps of Viking Lander sites 1 and 2 having a contour interval of 1.0 cm have been made to test the rectification method.

Wu, S. S. C.↗

NASA NTRS2002

P32Tools: reduction of ISOPHOT P32 oversampled maps

During the IS0 mission, the ISOPHOT instrument has collected more than 1100 observations in oversampled mapping mode (AOT PHT32) in the wavelength range of45 to 240 microns. The observations comprise mapping of small and large extended regions, but also faint point sources. PHT32 observations are affected by strong signal transients due to flux changes generated by the relatively fast chopper movement. A program described by Tuffs & Gabriel (2002), was developed to correct for these effects. It was integrated in the ISOPHOT Interactive Analysis (PIA) via a graphical user interface (GUI), so that most aspects of the processing can be addressed in a coherent and user friendly environment. The resulting package 'P32Tools' was introduced to the user community at three hands-on workshops on PHT32 processing held in spring 2001. The hands-on experience from these workshops lead to further improvements. Here we present an overview of the functionalities of the final release of this new software.

ISOPHOT oversampled mapping ISOPHOT Interactive An↗

NASA NTRS2010

CFD Models of a Serpentine Inlet, Fan, and Nozzle

Several computational fluid dynamics (CFD) codes were used to analyze the Versatile Integrated Inlet Propulsion Aerodynamics Rig (VIIPAR) located at NASA Glenn Research Center. The rig consists of a serpentine inlet, a rake assembly, inlet guide vanes, a 12-in. diameter tip-turbine driven fan stage, exit rakes or probes, and an exhaust nozzle with a translating centerbody. The analyses were done to develop computational capabilities for modeling inlet/fan interaction and to help interpret experimental data. Three-dimensional Reynolds averaged Navier-Stokes (RANS) calculations of the fan stage were used to predict the operating line of the stage, the effects of leakage from the turbine stream, and the effects of inlet guide vane (IGV) setting angle. Coupled axisymmetric calculations of a bellmouth, fan, and nozzle were used to develop techniques for coupling codes together and to investigate possible effects of the nozzle on the fan. RANS calculations of the serpentine inlet were coupled to Euler calculations of the fan to investigate the complete inlet/fan system. Computed wall static pressures along the inlet centerline agreed reasonably well with experimental data but computed total pressures at the aerodynamic interface plane (AIP) showed significant differences from the data. Inlet distortion was shown to reduce the fan corrected flow and pressure ratio, and was not completely eliminated by passage through the fan

Chima, R. V.↗

NASA NTRSDate not supplied

Feasibility Study to Extract Artemis-1 Fixed Base Modes While Mounted on a Dynamically Active Mobile Launch Platform

There are several challenges associated with the scheduled integrated modal test (IMT)of the Space Launch System (SLS) Artemis-1flight vehicle mounted on the mobile launcher (ML). While the goal of the test is to characterize the Artemis-1, the inclusion of the ML as the support stand for the test means that the entire system must be well characterized. A considerable amount of effort and schedule will have to be devoted to understanding both the test stand (the ML) and the Artemis-1 flight vehicle, and there is a risk that the effort may not be completed in time for a successful launch. NASA has requested that alternative methods be investigated to generate test results that can remove the effects of the ML from the test. ATA Engineering, Inc., (ATA)was given a reduced model f theArtemis-1 flight vehicle’s IMT configuration containing the candidate set of accelerometers and interface degrees of freedom (DOF). The model was used to determine how well ATA’s fixed base correction technique is able to estimate fixed base modes from test data collected on the IMT. This paper presents the fixed base correction method results.

modal testing↗

NASA NTRS1991

An investigation of error correcting techniques for OMV and AXAF

The original objectives of this project were to build a test system for the NASA 255/223 Reed/Solomon encoding/decoding chip set and circuit board. This test system was then to be interfaced with a convolutional system at MSFC to examine the performance of the concantinated codes. After considerable work, it was discovered that the convolutional system could not function as needed. This report documents the design, construction, and testing of the test apparatus for the R/S chip set. The approach taken was to verify the error correcting behavior of the chip set by injecting known error patterns onto data and observing the results. Error sequences were generated using pseudo-random number generator programs, with Poisson time distribution between errors and Gaussian burst lengths. Sample means, variances, and number of un-correctable errors were calculated for each data set before testing.

Ingels, Frank↗

NASA NTRS1993

An expert system shell for inferring vegetation characteristics: Interface for the addition of techniques (Task H)

All the NASA VEGetation Workbench (VEG) goals except the Learning System provide the scientist with several different techniques. When VEG is run, rules assist the scientist in selecting the best of the available techniques to apply to the sample of cover type data being studied. The techniques are stored in the VEG knowledge base. The design and implementation of an interface that allows the scientist to add new techniques to VEG without assistance from the developer were completed. A new interface that enables the scientist to add techniques to VEG without assistance from the developer was designed and implemented. This interface does not require the scientist to have a thorough knowledge of Knowledge Engineering Environment (KEE) by Intellicorp or a detailed knowledge of the structure of VEG. The interface prompts the scientist to enter the required information about the new technique. It prompts the scientist to enter the required Common Lisp functions for executing the technique and the left hand side of the rule that causes the technique to be selected. A template for each function and rule and detailed instructions about the arguments of the functions, the values they should return, and the format of the rule are displayed. Checks are made to ensure that the required data were entered, the functions compiled correctly, and the rule parsed correctly before the new technique is stored. The additional techniques are stored separately from the VEG knowledge base. When the VEG knowledge base is loaded, the additional techniques are not normally loaded. The interface allows the scientist the option of adding all the previously defined new techniques before running VEG. When the techniques are added, the required units to store the additional techniques are created automatically in the correct places in the VEG knowledge base. The methods file containing the functions required by the additional techniques is loaded. New rule units are created to store the new rules. The interface that allow the scientist to select which techniques to use is updated automatically to include the new techniques. Task H was completed. The interface that allows the scientist to add techniques to VEG was implemented and comprehensively tested. The Common Lisp code for the Add Techniques system is listed in Appendix A.

Harrison, P. Ann↗

NASA NTRS1989

Space module assembly apparatus with docking alignment flexibility and restraint

A berthing mechanism especially for use in berthing and compliant air-tight securing between manned space vehicle and modules is disclosed. The interface is provided by a pair of annular rings, one of which is typically, mechanically attached to the vehicle and the other to the module to which it is to be docked and secured. One of the two rings is attached to a base by resilient bellows. The facing surface of one annular ring is joined to a base by a cable laced through alternating pulleys attached circumferentially so that the interface surface of that ring may be tilted to accommodate angular misalignment as the annular rings are brought into docking (berthing) contact. Interleaving guide flanges with chambered sides provide at least some rotational mialignmnet correction. A plurality of electromechanical actuator/attenuator units provide means for extending one annular ring toward the other in the final stages of docking, for absorbing the initial docking shock and for drawing the annular rings into tight interface contact. Locking hooks provide for securing the interfaces.

Willie D Whitaker↗

NASA NTRS1986

BIOASPEN: System for technology development

The public version of ASPEN was installed in the VAX 11/750 computer. To examine the idea of BIOASPEN, a test example (the manufacture of acetone, butanol, and ethanol through a biological route) was chosen for simulation. Previous reports on the BIOASPEN project revealed the limitations of ASPEN in modeling this process. To overcome some of the difficulties, modules were written for the acid and enzyme hydrolyzers, the fermentor, and a sterilizer. Information required for these modules was obtained from the literature whenever possible. Additional support modules necessary for interfacing with ASPEN were also written. Some of ASPEN subroutines were themselves altered in order to ensure the correct running of the simulation program. After testing of these additions and charges was completed, the Acetone-Butanol-Ethanol (ABE) process was simulated. A release of ASPEN (which contained the Economic Subsystem) was obtained and installed. This subsection was tested and numerous charges were made in the FORTRAN code. Capital investment and operating cost studies were performed on the ABE process. Some alternatives in certain steps of the ABE simulation were investigated in order to elucidate their effects on the overall economics of the process.

Source record↗

NASA NTRS1998

Formal Analysis of Human Automation Interaction: The Problem of Display Correctness

This presentation attempted to develop a quantitative method for evaluating the effectiveness of autoflight displays. Researchers sought to develop a methodology for evaluation of display correctness and develop a methodology for display synthesis. Topics covered included: mode awareness, industry/research contributions, human-machine interface analysis, research objectives, modeling, flight guidance project and evaluation.

Degani, Asaf↗

NASA NTRS2010

Radio-Frequency Tank Eigenmode Sensor for Propellant Quantity Gauging

Although there are several methods for determining liquid level in a tank, there are no proven methods to quickly gauge the amount of propellant in a tank while it is in low gravity or under low-settling thrust conditions where propellant sloshing is an issue. Having the ability to quickly and accurately gauge propellant tanks in low-gravity is an enabling technology that would allow a spacecraft crew or mission control to always know the amount of propellant onboard, thus increasing the chances for a successful mission. The Radio Frequency Mass Gauge (RFMG) technique measures the electromagnetic eigenmodes, or natural resonant frequencies, of a tank containing a dielectric fluid. The essential hardware components consist of an RF network analyzer that measures the reflected power from an antenna probe mounted internal to the tank. At a resonant frequency, there is a drop in the reflected power, and these inverted peaks in the reflected power spectrum are identified as the tank eigenmode frequencies using a peak-detection software algorithm. This information is passed to a pattern-matching algorithm, which compares the measured eigenmode frequencies with a database of simulated eigenmode frequencies at various fill levels. A best match between the simulated and measured frequency values occurs at some fill level, which is then reported as the gauged fill level. The database of simulated eigenmode frequencies is created by using RF simulation software to calculate the tank eigenmodes at various fill levels. The input to the simulations consists of a fairly high-fidelity tank model with proper dimensions and including internal tank hardware, the dielectric properties of the fluid, and a defined liquid/vapor interface. Because of small discrepancies between the model and actual hardware, the measured empty tank spectra and simulations are used to create a set of correction factors for each mode (typically in the range of 0.999 1.001), which effectively accounts for the small discrepancies. These correction factors are multiplied to the modes at all fill levels. By comparing several measured modes with the simulations, it is possible to accurately gauge the amount of propellant in the tank. An advantage of the RFMG approach of applying computer simulations and a pattern-matching algorithm is that the Although there are several methods for determining liquid level in a tank, there are no proven methods to quickly gauge the amount of propellant in a tank while it is in low gravity or under low-settling thrust conditions where propellant sloshing is an issue. Having the ability to quickly and accurately gauge propellant tanks in low-gravity is an enabling technology that would allow a spacecraft crew or mission control to always know the amount of propellant onboard, thus increasing the chances for a successful mission. The Radio Frequency Mass Gauge (RFMG) technique measures the electromagnetic eigenmodes, or natural resonant frequencies, of a tank containing a dielectric fluid. The essential hardware components consist of an RF network analyzer that measures the reflected power from an antenna probe mounted internal to the tank. At a resonant frequency, there is a drop in the reflected power, and these inverted peaks in the reflected power spectrum are identified as the tank eigenmode frequencies using a peak-detection software algorithm. This information is passed to a pattern-matching algorithm, which compares the measured eigenmode frequencies with a database of simulated eigenmode frequencies at various fill levels. A best match between the simulated and measured frequency values occurs at some fill level, which is then reported as the gauged fill level. The database of simulated eigenmode frequencies is created by using RF simulation software to calculate the tank eigenmodes at various fill levels. The input to the simulations consists of a fairly high-fidelity tank model with proper dimensions and including internal tank harare, the dielectric properties of the fluid, and a defined liquid/vapor interface. Because of small discrepancies between the model and actual hardware, the measured empty tank spectra and simulations are used to create a set of correction factors for each mode (typically in the range of 0.999 1.001), which effectively accounts for the small discrepancies. These correction factors are multiplied to the modes at all fill levels. By comparing several measured modes with the simulations, it is possible to accurately gauge the amount of propellant in the tank. An advantage of the RFMG approach of applying computer simulations and a pattern-matching algorithm is that the

Zimmerli, Gregory A.↗

NASA NTRS1982

An assessment of the real-time application capabilities of the SIFT computer system

The real-time capabilities of the SIFT computer system, a highly reliable multicomputer architecture developed to support the flight controls of a relaxed static stability aircraft, are discussed. The SIFT computer system was designed to meet extremely high reliability requirements and to facilitate a formal proof of its correctness. Although SIFT represents a significant achievement in fault-tolerant system research it presents an unusual and restrictive interface to its users. The characteristics of the user interface and its impact on application system design are assessed.

Butler, R. W.↗