Search NASA⌕ Search

SEARCH · Search NASA

Results for “PALLADIUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Observations of exoelectron emission associated with heterogeneous catalysis

It is suggested that the exoelectron emission from the catalyst may be used to monitor the rate of oxidation of CO and CH4 over palladium catalysts. Indirect heating of the catalyst and atmospheric pressure have no effect upon this monitoring system. Although the mechanism relating catalysis to exoelectron emission is not clear, it is considered possible that electron emission is triggered by the adsorption-desorption cycle.

Hoenig, S. A.↗
NASA NTRS1977

Inverse isotope effect and the x dependence of the superconducting transition temperature in PdHx and PdDx

First-principles electron-band-structure calculations and measured phonon properties are employed in a calculation of the concentration dependence of the superconducting transition temperatures for PdHx and PdDx, including the inverse isotope effect. Excellent agreement with the experimental results is obtained. Our model also gives a qualitative understanding of the enhanced transition temperatures in the palladium-noble-metal hydrides.

Klein, B. M.↗
NASA NTRS1977

Investigation of low temperature carbon monoxide oxidation catalysts

Carbon monoxide generation rates related to the use of commerical equipment in Spacelab, added to the normal metabolic and subsystem loads, will produce carbon monoxide levels in excess of the maximum allowable concentration. In connection with the sensitivity of carbon monoxide oxidation catalysts to poisoning at room temperature, catalysts for an oxidation of carbon monoxide at low temperatures have been investigated. It was found that platinum and palladium are the only effective room temperature catalysts which are effective at 333 K. Hopcalite was ineffective at ambient temperatures, but converted CO with 100 percent efficiency at 333 K. Poisoning tests showed the noble metal catalysts to be very sensitive, and Hopcalite to be very resistant to poisoning.

Jagow, R. B.↗
NASA NTRS1977

Optimization of solar cells for air mass zero operation and a study of solar cells at high temperatures, phase 3

The etch-back epitaxy process is described for producing thin, graded composition GaAlAs layers. The palladium-aluminum contact system is discussed along with its associated problems. Recent solar cell results under simulated air mass zero light and at elevated temperatures are reported and the growth of thin polycrystalline GaAs films on foreign substrates is developed.

Blakeslee, A. E.↗
NASA NTRS1978

Center punched solar cell module development effort

The results are given of an advanced module development program with the objective of providing a low cost solar cell mechanical interconnect design. The design approach, which avoids soldering or welding operations, lends itself to automated assembly techniques thus supporting the Low-Cost Silicon Solar Array Project goals. The first group of six modules contained aluminum contact cells and the second group of six modules contained silver-titanium-palladium contact cells. Extensive component and environmental testing at the module level showed that reliable cell mechanical interconnection can be achieved when utilizing the proper electrical contact materials and pressures. A discussion is given of the module design, manufacturing procedure, test program, significant problem areas and solutions, and conclusions and recommendations as formulated and conducted by XEOS.

Ross, R. E.↗
NASA NTRS1979

Controlled metal-film deposition on alumina substrates

Report describes results of investigation of preparation, nucleation and controlled growth of particulate deposits (palladium and iron) on electron-transparent alumina substrates. Results indicate that characteristic properties of metal deposits are strongly dependent on cleanliness, phase, and crystallographic orientation of substrate.

Lee, E. H.↗
NASA NTRS1979

Development of Low Cost Contacts to Silicon Solar Cells

Different electroless plating systems were evaluated in conjunction with copper electroplating. All tests involved simultaneous deposition of front and back contacts using a standard cell materials. Cells with good adhesion and good curve fill factors were obtained using a palladium-chromium-copper metallization system. The final copper contact system was evaluated to determine if the copper would migrate at elevated temperatures. The copper migrated at elevated temperatures causing cell output degradation.

Iles, P. A.↗
NASA NTRS1979

Analysis of resistance-versus-pressure relations for the diamond indentor-anvil system

Pressures in excess of 1.4 Mbars have been attained by Ruoff and Wanagel (1977) by pressing tiny spherical diamond indentors (tip radius of 2 microns or less) against a diamond anvil. This system has been used for resistance-vs-pressure measurements as follows. A thin (200 A) coherent layer of a conductor, e.g., palladium, can be sputtered on the tip and on the anvil and electrical leads can then be attached to these at points remote from the contact area. Then a thin layer of the sample to be studied can be evaporated, sputtered, or placed on the anvil. When the indentor is pressed against the sample, the resistance changes as the pressure increases and as the contact radius increases. This paper analyzes the resistance-vs-pressure relationship for three different types of resistivity-vs-pressure behavior.

Ruoff, A. L.↗
NASA NTRS1978

The Pd2Si - /Pd/ - Ni - solder plated metallization system for silicon solar cells

The rationale and application of a plated metal system, Pd2Si Pd - Ni - solder, is presented. This metallization system is particularly useful on shallow p-n junction solar cells. The advantages of such plated solar cell contacts are discussed. A process sequence for applying the metallization system is outlined. A specific example is presented, including chemical plating solution formulations and detailed process step descriptions. Electrical test data for solar cells metallized with the palladium-nickel-solder system are provided.

Coleman, M. G.↗
NASA NTRS1980

Removal of hydrogen bubbles from nuclear reactors

Method proposed for removing large hydrogen bubbles from nuclear environment uses, in its simplest form, hollow spheres of palladium or platinum. Methods would result in hydrogen bubble being reduced in size without letting more radioactivity outside reactor.

Jenkins, R. V.↗
NASA NTRS1980

Phase 2 of the array automated assembly task for the low cost silicon solar array project

Studies were conducted on several fundamental aspects of electroless nickel/solder metallization for silicon solar cells. A process, which precedes the electroless nickel plating with several steps of palladium plating and heat treatment, was compared directly with single step electroless nickel plating. Work was directed toward answering specific questions concerning the effect of silicon surface oxide on nickel plating, effects of thermal stresses on the metallization, sintering of nickel plated on silicon, and effects of exposure to the plating solution on solar cell characteristics. The process was found to be extremely lengthy and cumbersome, and was also found to produce a product virtually identical to that produced by single step electroless nickel plating, as shown by adhesion tests and electrical characteristics of cells under illumination.

Petersen, R. C.↗
NASA NTRS1980

The automated array assembly task of the low-cost silicon solar array project, phase 2

Several specific processing steps as part of a total process sequence for manufacturing silicon solar cells were studied. Ion implantation was identified as the preferred process step for impurity doping. Unanalyzed beam ion implantation was shown to have major cost advantages over analyzed beam implantation. Further, high quality cells were fabricated using a high current unanalyzed beam. Mechanically masked plasma patterning of silicon nitride was shown to be capable of forming fine lines on silicon surfaces with spacings between mask and substrate as great as 250 micrometers. Extensive work was performed on advances in plated metallization. The need for the thick electroless palladium layer was eliminated. Further, copper was successfully utilized as a conductor layer utilizing nickel as a barrier to copper diffusion into the silicon. Plasma etching of silicon for texturing and saw damage removal was shown technically feasible but not cost effective compared to wet chemical etching techniques.

Coleman, M. G.↗
NASA NTRS1981

Demonstration of catalytic combustion with residual fuel

An experimental program was conducted to demonstrate catalytic combustion of a residual fuel oil. Three catalytic reactors, including a baseline configuration and two backup configurations based on baseline test results, were operated on No. 6 fuel oil. All reactors were multielement configurations consisting of ceramic honeycomb catalyzed with palladium on stabilized alumina. Stable operation on residual oil was demonstrated with the baseline configuration at a reactor inlet temperature of about 825 K (1025 F). At low inlet temperature, operation was precluded by apparent plugging of the catalytic reactor with residual oil. Reduced plugging tendency was demonstrated in the backup reactors by increasing the size of the catalyst channels at the reactor inlet, but plugging still occurred at inlet temperature below 725 K (845 F). Operation at the original design inlet temperature of 589 K (600 F) could not be demonstrated. Combustion efficiency above 99.5% was obtained with less than 5% reactor pressure drop. Thermally formed NO sub x levels were very low (less than 0.5 g NO2/kg fuel) but nearly 100% conversion of fuel-bound nitrogen to NO sub x was observed.

Dodds, W. J.↗
NASA NTRS1982

Multi-100 kW: Planar low cost solar array development

The applicability of selected low cost options to solar array blanket design was studied by fabricating representative modules and submitting them to thermal cycle environment. Large area (5.9 x 5.9 cm) solar cells of 3 varieties were purchased: (1) Standard wraparound, (2) Copper contacts substituted for the conventional Titanium-Palladium-Silver, and (3) Standard wraparound except with gridded back contact instead of continuous metallization. The baseline cell was purchased to compare fabrication cost and to serve as a control cell during test evaluation of the other two cells. All cells were assembled into either substrate modules where the cell is individually filtered and welded to an integrated Kapton-copper circuit or into a superstrate configuration with 4 cells jointly adhered to a single sheet of microsheet and then welded to the integrated Kapton-copper circuit. Cell quality, particularly in the metallization of contacts, was less than desired. Problems were encountered with copper metallization in laying down a barrier metal which would ohmically bond to the silicon. The cells received were shunted (sintered) or with low contact pull strength (non-sintered), thus leading to the decision to solder rather than weld the copper cells to the Kapton substrate.

Source record↗
NASA NTRS1982

UHV studies of the interaction of CO with small supported metal particles, Pd/mica

The interaction of carbon monoxide with small palladium particles supported on UHV-cleaved and heat-treated single-crystal mica was studied. The Pd particles were characterized and tested using the techniques of flash thermal desorption, Auger electron spectroscopy, core electron energy loss spectroscopy, and transmission electron microscopy. Evidence is presented for CO decomposition on Pd particles during CO adsorption-desorption experiments. The rate of CO decomposition increased rapidly with diminishing particle size. Residual carbon from CO decomposition blocked CO adsorption and had a strong poisoning effect on the CO oxidation reaction.

Doering, D. L.↗
NASA NTRS1982

Solid state instrumentation concepts for earth resource observation

Late in 1980, specifications were prepared for detail design definition of a six band solid state multispectral instrument having three visible (VIS), one near infrared (NIR), and two short wave infrared (SWIR) bands. This instrument concept, known as the Multispectral Linear Array (MLA), also offered increased spatial resolution, on board gain and offset correction, and additional operational modes which would allow for cross track and stereoscopic viewing as well as a multialtitude operational capability. A description is presented of a summary of some of the salient features of four different MLA design concepts, as developed by four American companies. The designs ranged from the use of multiple refractive telescopes utilizing three groups of focal plane detectors electronic correlation processing for achieving spatial registration, and incorporating palladium silicide (PdSi) SWIR detectors, to a four-mirror all-reflective telecentric system utilizing a beam splitter for spatial registration.

Richard, H. L.↗
NASA NTRS1984

Ti/Pd/Cu Contacts for Semiconductor Devices

Copper systems equivalent in performance to silver or gold systems. Titanium layer and palladium layer deposited on semiconductor device by electron beam evaporation. Desired pattern etched using photoresist. Thin layer of copper plated on contact pattern from cyanide solution. Copper layer then built up to 4 to 8 microns by electroplatng from acid solution.

Campbell, R. B.↗
NASA NTRS1982

High density Schottky barrier IRCCD sensors for SWIR applications at intermediate temperature

Monolithic 32 x 64 and 64 x 1:128 palladium silicide (Pd2Si) interline transfer infrared charge coupled devices (IRCCDs) sensitive in the 1 to 3.5 micron spectral band were developed. This silicon imager exhibits a low response nonuniformity of typically 0.2 to 1.6% rms, and was operated in the temperature range between 40 to 140 K. Spectral response measurements of test Pd2Si p-type Si devices yield quantum efficiencies of 7.9% at 1.25 microns, 5.6% at 1.65 microns 2.2% at 2.22 microns. Improvement in quantum efficiency is expected by optimizing the different structural parameters of the Pd2Si detectors. The spectral response of the Pd2Si detectors fit a modified Fowler emission model. The measured photo-electric barrier height for the Pd2Si detectors is 0.34 eV and the measured quantum efficiency coefficient, C1, is 19%/eV. The dark current level of Pd2Si Schottky barrier focal plane arrays (FPAs) is sufficiently low to enable operation at intermediate temperatures at TV frame rates. Typical dark current level measured at 120 K on the FPA is 2 nA/sq cm. The operating temperature of the Pd2Si FPA is compatible with passive cooler performance. In addition, high density Pd2Si Schottky barrier FPAs are manufactured with high yield and therefore represent an economical approach to short wavelength IR imaging. A Pd2Si Schottky barrier image sensor for push-broom multispectral imaging in the 1.25, 1.65, and 2.22 micron bands is being studied. The sensor will have two line arrays (dual band capability) of 512 detectors each, with 30 micron center-to-center detector spacing. The device will be suitable for chip-to-chip abutment, thus providing the capability to produce large, multiple chip focal planes with contiguous, in-line sensors.

Elabd, H.↗