Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLATES - BENDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Electropolishing of a Full-Sized U-10Mo Plate

Electropolishing is used to remove material from the surface of a metal using electric potential and current. U-10Mo fuel is produced from a low enriched uranium plate alloyed with 10% molybdenum (U-10Mo). Electropolishing is being considered in two steps of the process of fabricating this U-10Mo fuel. First, it could be used as a means initially improving the surface finish of the cast plate while removing smut from the casting process from the surface prior to homogenization. Second, it could be used again after homogenization to remove oxidation and continue to improve the surface finish prior to hot rolling. The purpose of this work is to demonstrate the process on full-size ingots and optimize the process. A depleted uranium U-10Mo plate was electropolished three times: the first two times were prior to homogenization and the third after a homogenization step. The first two polishes decreased the overall roughness, as measured by laser confocal microscopy. After each polish, a smoother and shinier blue-gold surface was left on the plate. Upon homogenization, the surface had a more matte appearance and the surface roughness increased back to the pre-homogenization values obtained prior to the initial polish. After electropolishing the homogenized pieces, the changes in surface roughness increased, as measured by laser confocal microscopy. The final polishing step was not long enough to return the surface roughness to pre-homogenization conditions, implying less polishing is needed before the homogenization versus afterwards. Heat generation during the polish was addressed by circulating the electrolyte solution through an external heat exchanger; however, solubility and anodization challenges require further study.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

HEU Pancake Plates

The HEU Pancake plates, formerly known as the Jemima plates, were procured in two batches. The first, consisting of the 15” plates, was ordered and produced by LANL in 1958. A second set, consisting of the 21” rings was ordered by LANL but produced by ORNL sometime in the 1960s. The plates were used at LACEF in experiments such as Big Ten and the Zeus series of experiments. In the mid-2000s, they were shipped to NCERC where they reside today. Since being at NCERC, they have been used in Zeus and TEX style experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Sensitivity calibration of a Carestream HPX-1 image plate scanner

There is a need to measure the sensitivity of the image plate scanners used to scan Z shot data. The Carestream HPX-1 image plate scanner was tested, and its performance was characterized to determine the system sensitivity in terms of signal per incident photon as a function of x-ray energy. A Manson source was used to simultaneously expose an Amptek x-ray multi-channel analyzer and image plates, allowing for a comparison of the counts as a function of energy to the signal recorded on the image plates. NIST-certified radioactive sources were used to assign an absolute sensitivity. Results indicate that the HPX-1 scanner response matches the shape of the modeled response, allowing for absolute scaling using NIST-certified radioisotope sources. The HPX-1 scanner shows a stable response with measurements taken over one week. In contrast, the sensitivity of the DITABIS scanner was characterized using the same approach, but it exhibits changes in its response that varied by more than 50% over the span of 4 days.

42 ENGINEERING↗
DOE OSTI2025

Increasing Radon Daughter Plate-out onto Superconducting Qubits

Radon daughter plate-out may pose a fundamental limitation to realizing large-scale superconducting quantum computers. Radon daughters plated-out onto a superconducting qubit chip can decay, releasing energy into the substrate, producing phonons. Phonon induced quasiparticles generate bit flip errors and reduce coherence times. We seek to increase plate-out on chips to enable future study of the impact of Radon on coherence times. In this project, we utilize COMSOL Multiphysics simulations to finalize design for a device to increase radon plate-out.

Kay, Dax [Northwestern U.]↗
DOE OSTI2021

Lead Contamination Differences in the Muscle of Wild Turkeys Harvested with Lead and Copper-Plated Lead Shot

Abstract Despite the known deleterious effects lead exposure can have on humans, lead remains the most common type of ammunition used to harvest big game and upland game birds. We sampled wild turkey Meleagris gallopavo breast muscle shot with standard lead and copper-plated lead pellets to quantify lead residue concentrations within the wound channel, and we sampled multiple adjacent locations to measure the extent lead contamination spreads through tissue of harvested turkeys. We found that samples taken from the wound channel contained more lead (mean = 3.76 μg/g dry weight) than both samples taken adjacent to the wound channel (mean = 0.20 μg/g dry weight) and samples taken from >5 cm away (mean = 0.15 μg/g dry weight). Additionally, we found that birds harvested with standard lead ammunition did not differ in lead concentrations from those shot with copper-plated lead, suggesting that copper plating does not aid in reducing lead exposure. Our findings suggest that wild turkeys harvested with either lead or copper-plated lead shot have the potential to expose consumers, especially children due to their lower tolerance, to low levels of lead that could exceed daily consumption limits set by the Food and Drug Administration and Centers for Disease Control. However, elevated lead levels were confined to the wound channel, and thus proper preparation of game to remove tissue surrounding wound channels may eliminate or substantially reduce lead exposure from harvested game birds.

Biodiversity & Conservation↗
DOE OSTI2020

Component and efficient plate and frame absorber

An absorber for an absorption refrigeration system for a vertically mounted plate absorber has fins positioned over the plate to promote distribution of a fluid under flow as a nearly continuous thin film. The absorber has rows of fins that are evenly spaced with the fins occupying a portion of the active width of the plate with adjacent rows offset by the width of the plate. A combined evaporator-absorber module is constructed with the absorbing face of the absorber parallel with an evaporating surface of an evaporator where absorber solution and refrigerant fall as parallel falling sheets of liquid. The absorber is covered with a porous hydrophobic membrane to isolate the falling absorber solution from the falling liquid refrigerant.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Overview of Base Model in Parametric Studies Specific to Performance of U-Mo Plates

This paper provides an overview of the base model specifically developed to perform parametric sensitivity studies on the U-10Mo monolithic fuel system. U-Mo monolithic fuels are being considered for the conversion of test reactors into high-performance research reactors that operate using proliferation-resistant, low-enriched uranium (LEU) fuels. These plate-type fuels contain a high-density, low-enrichment fuel sandwiched between zirconium diffusion barriers and encapsulated in aluminum claddings. All U.S. high-performance research reactors have released the designs of their LEU monolithic fuel reactor cores. These designs include nearly 50 distinct fuel plate geometries with different operational parameters. Consequently, a single generic plate geometry representing all the extreme points in this design matrix is unrealistic. To evaluate the performance for various parameters, a set of sensitivity studies was performed. These studies considered various input parameters (i.e., geometric, operational, and material property-related). The results revealed valuable information about plate performance and the sensitivity of this performance to various modeling inputs. To establish a reference state for comparing these result, base model featuring representative irradiation conditions was developed. To capture in-reactor behavior accurately, incorporation of representative constitutive models capable of evolving properties with respect to temperature, irradiation time, and burnup was needed. The behavioral models considered burnup-dependent properties, swelling, creep, and degradation. This paper introduces the base model created for the parametric sensitivity studies. The detailed description of the procedure includes the model geometry, model discretization, thermo-mechanical coupling, material properties and behavioral models. This paper also provides selected results and assesses the performance of the base model.

42 ENGINEERING↗
DOE OSTI2026

Increasing Radon Daughter Plate-out onto Superconducting Qubits

Radon daughter plate-out may pose a fundamental limitation to realizing large-scale superconducting quantum computers. Radon daughters plated-out on a superconducting qubit can decay, releasing energy into the substrate, producing phonons. Phonon-induced quasiparticles then generate bit-flip errors and reduce coherence times. We seek to increase plate-out on chips to enable future study of the impact of radon on coherence times. In this project, we utilize COMSOL Multiphysics simulations to visualize electric field configuration and model ion transport to finalize design of a device to increase radon plate-out on qubit chips.

Kay, Dax [Fermilab; Northwestern U.]↗
DOE OSTI2023

Contact pressure analysis to allow improved design for the clearing plate in a biomass comminution system

For biomass processing systems, feedstocks with small but equal sizes can improve flowability and thermochemical outputs. The Crumbler rotary shear system was designed to achieve such ideal feedstocks to reduce costs and energy throughout the biomass supply chain. Improving the wear resistance of major components in this system is important to decrease the cost. Accelerating the feedstock flow through the rotary shear machine plays an equivalent role of improving its efficiency. An analytical analysis and a finite-element analysis of the stationary clearing plate are presented in this work. Here, these tools are used to investigate the effect of contact surface curvature on the impact pressure. The optimized new clearing plate design is expected to improve the component’s lifetime and wood chips flowability. The field tests confirm that the trend of the new clearing plate design guided by FEA. The optimization method, model verification, and validation experience applied in this work can also be applied to other static components with similar simple contact wear problems.

09 BIOMASS FUELS↗
DOE OSTI2022

Experimental measurements and mathematical modeling of cold plate for aviation thermal management

Herein, this study, which has been motivated by the recent applications of the cold plate device in aviation thermal management, reports on physics-based mathematical models derived from the conservation laws of mass, momentum, and energy, and empiricism-based models. One of the objectives of the present work is to report on an elaborate and successful experimental work carried out on an additively manufactured device for the purpose of rigorously validating the numerical predictions. The excellent agreement between the numerical predictions and measured performance provides much needed confidence in the implementation, in the software package, of the offset-strip fin passage correlations, as well as in the software implementation of user-defined wavy fin correlations for aerospace heat exchangers and cold plates operating with ram air at Reynolds numbers below 8000. The contributions of this work can also be found in the development of a new and accurate thermal-hydraulic analysis procedure, referred to in this paper as plate-fin analogy. Results from this procedure are compared with those from thermal resistance network. The comparative study in this paper of the bulk and discrete enthalpy flux method is also new, as is the relative assessment of four off-set strip fin thermal-hydraulic models.

42 ENGINEERING↗
DOE OSTI2022

Fast charging of Li-ion cells: Effect of separator membranes and mapping of “safe lines” to avoid Li plating

An experimental method is introduced that uses microprobe Li/Cu reference electrodes to map "safe" charging regimes to avoid Li metal plating on graphite anodes at rates to 8C. With this method, a Li-ion cell closely approaches the Li plating condition but avoids descending into this regime. This "safe" approach is used to demonstrate effects of the microporous separator on Li plating in cells consisting of a layered nickel-manganese -cobalt oxide cathode and graphite anode. We argue that most of the difference in behaviors for different separators arises from time delayed Li + ion percolation through the membrane. In conclusion, our study suggests that explicitly treating kinetics of phase transitions in the lithiated graphite anode is essential for electrochemical models predicting "safe" lines for fast charging cells.

25 ENERGY STORAGE↗
DOE OSTI2023

Thermomechanical analysis and modeling of involute-shaped fuel plates using the Cheverton–Kelley experiments for the High Flux Isotope Reactor

Three research reactors with involute-shaped fuel plates are pursuing conversion from highly enriched uranium to low-enriched uranium fuel. Various core design and safety evaluation studies are essential to assess the feasibility of the conversion. The use of 3D computational multiphysics codes is being explored in these analyses and therefore they must undergo a thorough evaluation and quality assurance process due to their potential impact on nuclear safety. Here, the Cheverton and Kelley physical tests performed in the late 1960s to investigate the deflections of HFIR’s outer plate under uniform pressure and temperature fields are simulated by employing commercially available computational codes, with the goals to (1) verify and validate the models and numerical solvers implemented in the codes for thermomechanical analysis of involute reactor plates and (2) to develop a benchmark computational test to evaluate future versions of existing software or newly developed computational codes. The results of the simulations showed good agreement with each other as well as against the Cheverton–Kelley experimental data. Some minor deviations were observed for a few multiphysics cases and their potential origins and impact on the analysis results is investigated in the paper. The validated models increase the confidence in using multiphysics codes to evaluate existing or new LEU designs.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

Mechanistic Analysis of Microstructural Attributes to Lithium Plating in Fast Charging

Metallic lithium deposition on graphite anodes is a critical degradation mode in lithium-ion batteries, which limits safety and fast charge capability. A conclusive strategy to mitigate lithium deposition under fast charging yet remains elusive. Herein, we examine the role of electrode microstructure in mitigating lithium plating behavior under various operating conditions, including fast charging. The multilength scale characteristics of the electrode microstructure lead to a complex interaction of transport and kinetic limitations that significantly governs the cell performance and the occurrence of Li plating. We demonstrate, based on a comprehensive mesoscale analysis, that the performance and degradation can be significantly modulated via systematic design improvements at the hierarchy of length scales. It is found that the improvement in kinetic and transport characteristics achievable at disparate scales can dramatically affect Li plating propensity.

25 ENERGY STORAGE↗
DOE OSTI2021

Pressure Response Optimization of an Eddy Current-Driven Flyer Plate Valve for the ITER Shattered Pellet Injection System

One technique for mitigating disruptions in a tokamak is shattered pellet injection (SPI). SPI is a process in which a large solid pellet consisting of deuterium, neon, or argon is desublimated in a pipe gun barsrel and launched downstream. Pellets are shattered just before entering the plasma by an impact with an angled tube. Injection of these materials into the plasma radiates stored thermal energy, limits current decay rates, suppresses the generation of runaway electrons, and dissipates runaway electrons if necessary. A critical element of the SPI system is a fast-acting valve that releases high-pressure gas to dislodge and accelerate pellets directly, or indirectly via a mechanical punch. A prototype valve sized for the ITER SPI system has been designed and fabricated. A pulsed high-voltage power supply energizes the valve’s internal magnetic coil, which induces eddy currents in the adjacent flyer plate resulting in a repulsive force between the flyer plate and the coil. The flyer plate action lifts a valve seat, allowing high-pressure gas to flow from the valve plenum to the downstream (breech) location of the pellet or mechanical punch. All of the valve’s internal components are designed to operate in ITER-level static background magnetic fields. Here, a study was conducted to optimize the downstream pressure response for a range of valve sizes and operating pressures. In particular, the study analyzes the breech pressure response associated with varying plenum pressures as well as varying breech volumes. A computational fluid dynamics simulation was built in STAR-CCM+ and validated against data from laboratory experiments. The resulting simulation outputs, in the form of downstream responses for a variety of initial plenum pressures and breech volumes, will be used as a complement to experimental data to ensure the pressure pulse is suitable for pellet survivability. These data, combined with studies on pellet shear strength and shock response, will be applied to optimization of overall operating parameters of the ITER SPI system.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Development of an Experimental Approach to Achieve Spatially Resolved Plant Root-Associated Metaproteomics Using an Agar-Plate System

Plant–microbe interactions in the rhizosphere play a vital role in plant health and productivity. The composition and function of root-associated microbiomes is strongly influenced by their surrounding environment, which is often customized by their host. How microbiomes change with respect to space and time across plant roots remains poorly understood, and methodologies that facilitate spatiotemporal metaproteomic studies of root-associated microbiomes are yet to be realized. Here, we developed a method that provides spatially resolved metaproteome measurements along plant roots embedded in agar-plate culture systems, which have long been used to study plants. Spatially defined agar “plugs” of interest were excised and subsequently processed using a novel peptide extraction method prior to metaproteomics, which was used to infer both microbial community composition and function. As a proof-of-principle, a previously studied 10-member community constructed from a Populus root system was grown in an agar plate with a 3-week-old Populus trichocarpa plant. Metaproteomics was performed across two time points (24 and 48 h) for three distinct locations (root base, root tip, and a region distant from the root). The spatial resolution of these measurements provides evidence that microbiome composition and expression changes across the plant root interface. Interrogation of the individual microbial proteomes revealed functional profiles related to their behavioral associations with the plant root, in which chemotaxis and augmented metabolism likely supported predominance of the most abundant member. This study demonstrated a novel peptide extraction method for studying plant agar-plate culture systems, which was previously unsuitable for (meta)proteomic measurements.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Analyzing photovoltaic module mechanics using composite plate theories and finite element solutions

Deflection and stress calculated from an experimentally validated, high-fidelity finite element model (FEM) of a photovoltaic module experiencing mechanical load was compared to results from a simplified FEM treating the module laminate as a homogenized composite using a rule of mixtures approach, and further compared to analytical calculations treating the module as a Kirchoff-Love flat plate. The goal of this study was to determine the error incurred by analyzing module mechanics with varying levels of simplification, since resolving the aspect ratios of a module is computationally expensive. Homogenized FEMs were found to underpredict peak deflection under a 1.0 kPa load by between 13 and 19% for lower and upper bound application of the rule of mixtures. However, module shape was captured, implying that a useful replication of a resolved model could be achieved with a reduced, calibrated material stiffness. Homogenized stress results captured glass layer tensile stress components to within 46 to 52% at a sample location of interest, though agreement was poor through the remainder of the laminate due to the lack of material resolution. For plate theory, deflection was overpredicted by 45 to 67% for upper and lower bound homogenizations, and frame-adjacent module shapes were not adequately replicated. Stress results mirrored FEM trends but magnitudes were not well correlated to resolved model values. These results support the use of homogenized laminate models for module shape derivation, though resolved models remain necessary for stress analyses. The accuracy of plate theory was found to be inadequate for most applications.

14 SOLAR ENERGY↗
DOE OSTI2025

Joining Study for Formed Plate Heat Exchangers (CRADA Final Report)

Plate heat exchangers (PHEs) have been used in numerous industrial applications, such as HVAC systems, power generation, transportation and manufacturing. The performance of plate heat exchangers is frequently undermined by corrosion, fouling, and scaling. These phenomena not only diminish heat transfer efficiency but also lead to increased operational costs, maintenance demands, and reduced equipment lifespan. In this project, the team addressed the widespread challenges of corrosion, fouling, and scaling, and explored alternative material solutions. While commonly used materials like stainless steel and titanium offer notable benefits, they can still experience corrosion under certain operating conditions. The advancement of new materials and surface engineering technologies, such as advanced coating, ceramics, composites materials, and high entropy alloys are promising for can help solve these issues, enable longer lifetime and high performance of plate heat exchangers.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

Assessing the Heat Transfer Modeling Capabilities of CFD Software for Involute-Shaped Plate Research Reactors

The ongoing efforts to convert High-Performance Research Reactors (HPRRs) using Highly Enriched Uranium (HEU) to Low-Enriched Uranium (LEU) fuel require reliable thermal–hydraulic assessments of modified core designs. The involute-shaped fuel plates used in several major HPRRs present unique modeling challenges due to their compact core geometries and high heat flux conditions. This study evaluates the capability of three commercial CFD tools, STAR-CCM+, COMSOL, and ANSYS CFX, to predict cladding-to-coolant heat transfer using Reynolds-Averaged Navier–Stokes (RANS) methods within the thermal–hydraulic regimes of involute-shaped plate reactors. Broad sensitivity analysis was conducted across a range of reactor-relevant parameters using two turbulence models (k−ϵ and k−ω SST) and different near-wall treatment strategies. The results were benchmarked against the Sieder–Tate correlation and experimental data from historic studies. The codes produced consistent results, showing good agreement with the empirical correlation of Sieder–Tate and the experimental measurements. The findings support the use of these commercial CFD codes as effective tools for assessing the thermal–hydraulic performance of involute-shaped plate HPRRs and guide future LEU core development.

CFD↗