SEARCH · Search NASA

Results for “Residue”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Effects of mechanical and thermal cycling on composite and hybrid laminates with residual stresses

The effects of tensile load cycling and thermal cycling on residual stiffness and strength properties of the following composite and hybrid angle-ply laminates were studied: boron/epoxy, boron/polyimide, graphite/low-modulus epoxy, graphite/high-modulus epoxy, graphite/polyimide, S-glass/epoxy, graphite/Kevlar 49/epoxy, and graphite/S-glass/epoxy. Specimens of the first six types were mechanically cycled up to 90% of static strength. Those that survived 10 million cycles were tested statically to failure, and no significant changes in residual strength and modulus were noted. Specimens of all types were subjected to thermal cycling between room temperature and 411 K for the epoxy-matrix composites and 533 K for the polyimide-matrix composites. The residual strength and stiffness remained largely unchanged, except for the graphite/low-modulus epoxy, which showed reductions in both of approximately 35%. When low-temperature thermal cycling under tensile load was applied, there was a noticeable reduction in modulus and strength in the graphite/low-modulus epoxy and some strength reduction in the S-glass/epoxy.

Daniel, I. M.↗

NASA NTRS1980

Calculation of residual principal stresses in CVD boron on carbon filaments

A three-dimensional finite element model of the chemical vapor deposition of boron on a carbon substrate (B/C) is developed. The model includes an expansion of the boron after deposition due to atomic rearrangement and includes creep of the boron and carbon. Curves are presented showing the variation of the principal residual stresses and the filament elongation with the parameters defining deposition strain and creep. The calculated results are compared with experimental axial residual stress and elongation measurements made on B/C filaments. For good agreement between calculated and experimental results, the deposited boron must continue to expand after deposition, and the build up of residual stresses must be limited by significant boron and carbon creep rates.

Behrendt, D. R.↗

NASA NTRS1980

Certain features of the cochleovestibular syndrome in the residual stage of traumatic brain disease

Caloric and rotation tests were applied to the study of the vestibular analyser in 84 patients in the residual state of traumatic disease of the brain. Vestibular disturbances of different degree revealed in 79 patients were as a rule accomplished by cochlear derangement. In the majority of patients the vestibular syndrome was supratentorial with the involvement of the diencephal-hypothalmic, subcortical, and cortical levels of the brain. Vestibular dysfunction correlated with such factors as severity of the sustained craniocerebral traum, duration of the posttraumatic period, and, particularly, with the character of the residual neurological syndrome. In accordance with the latter, it is recommended that vestibular disturbances be treated in the residual period of closed craniocerebral injuries with due regard for the principal pathophysiological mechanisms of the underlying neurological syndrome.

Garshin, M. I.↗

NASA NTRS1980

Calculation of residual principal stresses in CVD boron on carbon filaments

A three-dimensional finite element model of the chemical vapor deposition (CVD) of boron on a carbon substrate (B/C) is developed. The model includes an expansion of the boron after deposition due to atomic rearrangement and includes creep of the boron and carbon. Curves are presented to show how the principal residual stresses and the filament elongation vary as the parameters defining deposition strain and creep are varied. The calculated results are compared with experimental axial residual stress and elongation measurements made on B/C filaments. This comparison requires that for good agreement between calculated and experimental results, the deposited boron must continue to expand after deposition, and that the build-up of residual stresses is limited by significant boron and carbon creep rates.

Behrendt, D. R.↗

NASA NTRS1980

Hg and Pt-metals in meteorite carbon-rich residues - Suggestions for possible host phase for Hg

Carbon-rich and oxide residual phases have been isolated from Allende and Murchison by acid demineralization for the determination of their Hg, Pt-metal, Cr, Sc, Co, and Fe contents. Experimental procedures used eliminated the possibility of exogenous and endogenous contaminant trace elements from coprecipitating with the residues. Large enrichments of Hg and Pt-metals were found in Allende but not in Murchison residues. Hg-release profiles from stepwise heating experiments suggest a sulfide as the host for Hg. Diffusion calculations for Hg based on these experiments indicate an activation energy of 7-8 kcal/mol, the same as that for Hg in troilite from an iron meteorite. This is further support for a sulfide host phase for Hg. Equilibration of Hg with this phase at approximately 900 K is indicated. Reasons for the presence of Pt-metals in noncosmic relative abundances are explored.

Jovanovic, S.↗

NASA NTRS1981

Acoustic transmission in non-uniform ducts with mean flow. I - The method of weighted residuals. II - The finite element method

The problem of acoustic transmission through nonuniform ducts containing a high-speed subsonic flow is studied by means of the method of weighted residuals in the form of a modified Galerkin method and a Galerkin formulation of the finite element method. The method of weighted residuals is shown to employ the basis functions generated from eigenvalue calculations for the case of no flow, and is verified by comparison with exact eigenvalue calculations in the uniform duct case and numerical solutions of the one-dimensional form of the equations in the nonuniform duct case. The finite element scheme based on both the Galerkin method and the residual least squares method and employing eight-noded isoparametric elements is presented and used to investigate multimodal propagation by the coupling of the solution in the duct nonuniform section to modal expansions in uniform sections. Comparison of the results of the two methods reveals them to be in substantial agreement, and predicts the importance of multimodal interactions at high Mach numbers.

Eversman, W.↗

NASA NTRS1981

Demonstration of catalytic combustion with residual fuel

An experimental program was conducted to demonstrate catalytic combustion of a residual fuel oil. Three catalytic reactors, including a baseline configuration and two backup configurations based on baseline test results, were operated on No. 6 fuel oil. All reactors were multielement configurations consisting of ceramic honeycomb catalyzed with palladium on stabilized alumina. Stable operation on residual oil was demonstrated with the baseline configuration at a reactor inlet temperature of about 825 K (1025 F). At low inlet temperature, operation was precluded by apparent plugging of the catalytic reactor with residual oil. Reduced plugging tendency was demonstrated in the backup reactors by increasing the size of the catalyst channels at the reactor inlet, but plugging still occurred at inlet temperature below 725 K (845 F). Operation at the original design inlet temperature of 589 K (600 F) could not be demonstrated. Combustion efficiency above 99.5% was obtained with less than 5% reactor pressure drop. Thermally formed NO sub x levels were very low (less than 0.5 g NO2/kg fuel) but nearly 100% conversion of fuel-bound nitrogen to NO sub x was observed.

Dodds, W. J.↗

NASA NTRS1982

The residue-measure criterion for model reduction in the analysis of the NASA Space Shuttle's digital flight control system

A residue-measure criterion model reduction technique is applied to the vehicle dynamics model used in the design and analysis of the NASA Space Shuttle's digital flight control system. As implemented in this study the residue-measure technique involved an a priori residue calculation with control system biasing. The predictions of the reduced model are compared to vehicle level dynamic stability test data. These comparisons show an excellent correlation of the dominant spectral and response features between the model and test data. In addition, the application of the reduction technique to various Shuttle mission flight phases is demonstrated.

Gluch, D. P.↗

NASA NTRS1982

Electron microscopy of carbonaceous matter in Allende acid residues

On the basis of characteristic diffuse ring diffraction patterns, much of the carbonaceous matter in a large suite of Allende acid residues has been identified as a variety of turbostratic carbon. Crystallites of this phase contain randomly stacked sp(2) hybridized carbon layers and diffraction patterns resemble those from carbon black and glassy carbon. Carbynes are probably absent, and are certainly restricted to less than 0.5% of these acid residues. The work of Ott et al. (1981) provides a basis for the possibility that turbostratic carbon is a carrier of noble gases, but an additional component - amorphous carbon - may be necessary to explain the high release temperatures of noble gases as well as the glassy character of many of the carbonaceous particles. Carbynes are considered to be questionable as important carriers of noble gases in the Allende acid residues.

Lumpkin, G. R.↗

NASA NTRS1982

Refractory residues, condensates and chondrules from solar furnace experiments

Vertical access solar furnace experiments have produced refractory residues, condensates and chondrules that are similar to components of chondritic meteorites. In particular, Ca-Al-rich refractory residues similar in chemistry to inclusions in carbonaceous chondrites have been produced by partial evaporation of basaltic bulk rock samples. Fe-Mg-Si-rich condensates with distinctive microbotryoidal morphology have been collected from the same sample runs. Particle coatings and aggregates with virtually identical microbotryoidal morphology and major element chemistry have been identified in both the Allende and Murchison meteorites. Spattered drops from melt beads undergoing heating and partial evaporation resemble some meteoritic chondrules in their mineralogies, textures, grain size, and sorting. The spatter mechanism is highly efficient in the production of chondrules. If any of the refractory inclusions in chondrites are, in fact, partial evaporation residues, many meteoritic fluid drop chondrules must have been formed by this process. The hot central portion of the solar nebula, acting on a cloud of dust and gas, is the probable source of heat required to produce the fractionated chemistry and physical state of many of the components of chondritic meteorites.

King, E. A.↗

NASA NTRS1983

Optical systolic array processor using residue arithmetic

The use of residue arithmetic to increase the accuracy and reduce the dynamic range requirements of optical matrix-vector processors is evaluated. It is determined that matrix-vector operations and iterative algorithms can be performed totally in residue notation. A new parallel residue quantizer circuit is developed which significantly improves the performance of the systolic array feedback processor. Results are presented of a computer simulation of this system used to solve a set of three simultaneous equations.

Jackson, J.↗

NASA NTRS1984

The Effect of Creep on the Residual Stresses Generated During Silicon Sheet Growth

The modeling of stresses generated during the growth of thin silicon sheets at high speeds is an important part of the EFG technique since the experimental measurement of the stresses is difficult and prohibitive. The residual stresses which arise in such a growth process lead to serious problems which make thin Si ribbons unsuitable for fabrication. The constitutive behavior is unrealistic because at high temperature (close to the melting point) Si exhibits considerable creep which significantly relaxes the residual stresses. The effect of creep on the residual stresses generated during the growth of Si sheets at high speeds was addressed and the basic qualitative effect of creep are reported.

Hutchinson, J. W.↗

NASA NTRS1983

Residual strength assessment of low velocity impact damage of graphite-epoxy laminates

This report contains the study of Low Velocity Transverse Impact Damage of graphite-epoxy T300/5208 composite laminates. The specimen, 100 mm diameter clamped plates, were impact damaged by a cantilever-type instrumented 1-inch diameter steel ball. Study was limited to impact velocity 6 m/sec. Rectangular strips, 50 mm x 125 mm, were cut from the impact-damage specimens so that the impact damage zone was in the center of the strips. These strips were tested in tension to obtain their residual strength. An energy dissipation model was developed to predict the residual strength from fracture mechanics concepts. Net energy absorbed I(a) was evaluated from coefficient of restitution concepts based on shear dominated theory of fiber-reinforced materials, with the modification that during loading and unloading the shear deformation are respectively elastic-plastic and elastic. Delamination energy I(d) was predicted by assuming that the stiffness of the laminate dropped due to debonding. Fiber-breakage energy, assumed to be equal to the difference of I(a) and I(d), was used to determine the residual strength. Predictions were compared with test results.

Lal, K. M.↗

NASA NTRS1984

S-P wave travel time residuals and lateral inhomogeneity in the mantle beneath Tibet and the Himalaya

S-P wave travel time residuals were measured in earthquakes in Tibet and the Himalaya in order to study lateral inhomogeneities in the earth's mantle. Average S-P residuals, measured with respect to Jeffrey-Bullen (J-B) tables for 11 earthquakes in the Himalaya are less than +1 second. Average J-B S-P from 10 of 11 earthquakes in Tibet, however, are greater than +1 second even when corrected for local crustal thickness. The largest values, ranging between 2.5 and 4.9 seconds are for five events in central and northern Tibet, and they imply that the average velocities in the crust and upper mantle in this part of Tibet are 4 to 10 percent lower than those beneath the Himalaya. On the basis of the data, it is concluded that it is unlikely that a shield structure lies beneath north central Tibet unless the S-P residuals are due to structural variations occurring deeper than 250 km.

Molnar, P.↗

NASA NTRS1985

Residual thermal and moisture influences on the strain energy release rate analysis of edge delamination

A laminated plate theory analysis is developed to calculate the strain energy release rate associated with edge delamination growth in a composite laminate. The analysis includes the contribution of residual thermal and moisture stresses to the strain energy released. The strain energy release rate, G, increased when residual thermal effects were combined with applied mechanical strains, but then decreased when increasing moisture content was included. A quasi-three-dimensional finite element analysis indicated identical trends and demonstrated these same trends for the individual strain energy release rate components, G sub I and G sub II, associated with interlaminar tension and shear. An experimental study indicated that for T300/5208 graphite-epoxy composites, the inclusion of residual thermal and moisture stresses did not significantly alter the calculation of interlaminar fracture toughness from strain energy release rate analysis of edge delamination data taken at room temperature, ambient conditions.

Obrien, T. K.↗

NASA NTRS1985

Residual stresses of thin, short rectangular plates

The analysis of the residual stresses in thin, short rectangular plates is presented. The analysis is used in conjunction with a shadow moire interferometry technique by which residual stresses are obtained over a large spatial area from a strain measurement. The technique and analysis are applied to a residual stress measurement of polycrystalline silicon sheet grown by the edge-defined film growth technique.

Andonian, A. T.↗

NASA NTRS1986

Residual thermal and moisture influences on the strain energy release rate analysis of edge delamination

Obrien, T. K.↗

NASA NTRS1987

Inelastic strain analogy for piecewise linear computation of creep residues in built-up structures

An analogy between inelastic strains caused by temperature and those caused by creep is presented in terms of isotropic elasticity. It is shown how the theoretical aspects can be blended with existing finite-element computer programs to exact a piecewise linear solution. The creep effect is determined by using the thermal stress computational approach, if appropriate alterations are made to the thermal expansion of the individual elements. The overall transient solution is achieved by consecutive piecewise linear iterations. The total residue caused by creep is obtained by accumulating creep residues for each iteration and then resubmitting the total residues for each element as an equivalent input. A typical creep law is tested for incremental time convergence. The results indicate that the approach is practical, with a valid indication of the extent of creep after approximately 20 hr of incremental time. The general analogy between body forces and inelastic strain gradients is discussed with respect to how an inelastic problem can be worked as an elastic problem.

Jenkins, Jerald M.↗