Results for “Transient Testing Reactor” — Page 8

DOE OSTI2022

Development of the TREAT M2 experiment as a transient benchmark

A transient benchmark based on the Transient Reactor Test Facility (TREAT) M2 Calibration experiment (M2-CAL) is under development. TREAT, at Idaho National Laboratory, is a graphite moderated air-cooled research reactor which has been used extensively for fuel material testing under extreme and accident conditions. Accurate benchmark models are a beneficial component in the operations, experimental planning, and development of TREAT. In this work, we present a transient benchmark model for the M2-CAL experiment core loading. The benchmark model incorporates the coupling between the Monte Carlo Code SERPENT and the computational fluid dynamics code OpenFOAM to capture the temperature feedback mechanism. The M2-CAL transient 2580 was simulated in this work. A pre-transient analysis was performed to determine the optimum core composition and conditions before the beginning of the transient. The analysis was validated against historic TREAT kinetic measurements and the worth of the transient rod T-2. The axial power distribution in the flux wire for the M2-CAL experiment was determined and contrasted with the experiment. The model was then used to simulate the M2-CAL transient 2580 experiment based on the reported pre-transient and transient conditions. Several transient observables were calculated and compared to the experiment. The model shows good agreement with the experimental power traces, period, and average increase of power at the power ramp (time > 7.8 s). Inverse point kinetics analysis was performed during the period of the power ramp for the model and the experiment based on that, the temperature feedback component was isolated and contrasted with the experimental feedback. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2020

Impact of Grain Size on Performance Degradation of TREAT LEU

We argue that radiation damage induced degradation of thermal conductivity does not set a lower limit on fuel grain sizes for the low enriched uranium fuel design of the Transient Reactor Test Facility (TREAT). Earlier work reports that smaller grains cause a larger degradation of thermal conductivity than larger grains constraining the smallest feasible size of fuel grains. This work assesses TREAT’s transient performance in the presence of radiation damage. The difference between the two studies is in treating damaged and fresh graphite as serial (this work) or parallel (previous) heat resistors. We use a multiphysics model of TREAT fuel grains to compute the reduction in transient capability measured by the total deposited energy as a function of irradiation dose. We find that radiation damage has a negligible effect on energy deposition.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Microstructural and phase changes in alpha uranium investigated via in-situ studies and molecular dynamics

A deeper knowledge of thermally induced microstructural and phase evolution in nuclear metallic fuel can be obtained using novel in-situ microscopic analyses. Such studies can provide information on the dynamics of phase transitions which is not possible with conventional postmortem characterization (post-irradiation examination). In this work, the behavior of alpha uranium (α-U) was investigated via in-situ heating tests in a transmission electron microscope. Here, the main objective is to understand the microstructural and phase changes, such as defect annihilation and ß phase formation and retention, observed in reactor in-pile transient studies at the Transient Reactor Test facility. Indeed, defect migration and rearrangement were observed within the α phase starting at 673 K; α→ß phase transition was observed between 773 K and 1,073 K during the heating ramp (which is in the temperature window reported for α→ß transition temperatures). Recrystallization and formation of nano grains was observed at high temperatures (over 1,073 K). Such recrystallization was possibly related to the formation of the γ phase. Finally, it was indeed observed that the ß phase (but not γ phase) was retained at room temperature upon rapid cooling. Molecular dynamics studies support these experimental results and shows that the γ phase of pure uranium cannot be retained at room temperature if not stabilized with the addition of an alloying element.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2018

A high-efficiency, low-Ĉerenkov Micro-Layered Fast-Neutron Detector for the $\mathrm{TREAT}$ hodoscope

Here this paper presents an enabling technology for high-efficiency fast-neutron detection for the Transient Reactor Test (TREAT) Facility hodoscope. The hodoscope is currently outfitted with 25.4-mm long Hornyak buttons for fast-neutron detection. However, they require improvements, as they suffer from low detection efficiency, Ĉerenkov radiation contaminating the signal, and non-linearity of detector response at large transients. To address these issues, a layered ZnS:Ag device has been constructed. The layered design provides various advantages: it incorporates greater scintillation volume, Ĉerenkov background is significantly reduced by eliminating the need for additional light guides, and the detection process is simplified by achieving gamma-ray rejection using only pulse-height discrimination. The result is a greater number of fast neutron counts with reduced background noise contaminating the signal. On being irradiated with a 252Cf source (whose neutron energy spectrum closely mimics a reactor fission spectrum), a 25.4-mm long layered device was found to exhibit an intrinsic fast-neutron detection efficiency of 8.1% for neutrons with an average energy of 2 MeV, while a 43-mm long device allows for a greater number of fast neutron to be detected, increasing the efficiency to 9.1%. Further lengthening of the device up to 20 cm has been numerically predicted to exhibit even higher efficiencies. The detectors can be mass-produced easily and inexpensively.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2024

MARVEL Reactor Fuel Performance Report (Rev.2)

The Microreactor Applications Research Validation and EvaLuation (MARVEL) project is producing a high temperature liquid metal-cooled nuclear test bed at Idaho National Laboratory (INL) to ultimately improve the integration of microreactors to end-user applications. This ambitious effort seeks to design, authorize, construct, test, and operate the reactor within five years. In order to construct and operate the MARVEL reactor in a timely manner, the system will utilize materials and component designs which have already been used, qualified, or licensed from previous reactors. The MARVEL reactor will be located at the INL Transient Reactor Test (TREAT) facility in the north high-bay equipment pit and will use the existing 304 stainless steel-clad U-ZrH1.6 pin-type fuel system developed by General Atomics and purchased from TRIGA International. This fuel has been previously qualified under the United States Department of Energy’s (US DOE) Reduced Enrichment for Research and Test Reactors (RERTR) Program. Even though the regulator of the MARVEL reactor is the US DOE, the standards and overall approach recommended by the Nuclear Regulatory Commission is well-defined and utilized here. Following NUREG-1537 regulatory guidance, this report documents the authorization case for the MARVEL fuel system’s application to MARVEL and establishes stable and predictable fuel performance during the most thermophysically unfavorable conditions achievable in the MARVEL reactor. To that end, this report provides a comprehensive survey of the known thermophysical properties, performance, and quantitative relationships associated with the MARVEL reactor fuel element and uses this information to determine its mechanical integrity and risk of reaching unacceptable conditions during the most extreme accident scenarios predicted for the reactor using the most conservative assumptions available. The information contained herein is compiled from a combination of historical reports and peer reviewed scientific publication manuscripts. Known mechanisms under which the fuel is susceptible to failure are highlighted and compared to conditions that could exist in the MARVEL reactor during an unanticipated transient or accident scenario. The two scenarios considered for analysis in this report are (1) an unprotected loss of flow accident and (2) a hypothetical unprotected loss of coolant accident during the loss of flow accident. Preliminary 2D steady-state analyses herein indicate that both fuel-cladding chemical interactions and fuel-cladding mechanical interactions are negligible throughout the fuel’s operational cycle under both normal and high temperature accident scenario conditions. Although higher fidelity 3D time-dependent modeling and simulations are planned, the following may be concluded presently. The MARVEL fuel element maintains its geometric stability and structural integrity during the most extreme accident scenarios predicted for the MARVEL reactor. The hoop stress during the unprotected loss of flow accident reaches about -1.27 MPa; this negative stress indicates that it is compressive rather than tensile. The compressive stress is a result of the NaK pressure on the outside of the fuel element, caused by the restricted thermal expansion of the NaK coolant, exceeding the internal pressures generated inside of the fuel element. The hoop stress generated in the cladding during the unprotected loss of coolant accident reaches a maximum of about approximately 10 MPa, which is nearly an order of magnitude less than the predicted yield strength of the cladding under high-temperature accident scenario conditions. Calculations were compared with results from high performance computational simulations using BISON and are in very close agreement. A conservative MARVEL fuel meat peak temperature limit of 900 °C is recommended presently, which is about 180 °C higher than the peak fuel temperature predicted to occur during the most extreme accident. Based on the known properties and behavior of the MARVEL fuel element, the fuel successfully meets its design and safety requirements under normal and most extreme accident conditions with a large safety margin.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

MARVEL Reactor Fuel Performance Report

The Microreactor Applications Research Validation and EvaLuation (MARVEL) project is producing a high temperature liquid metal-cooled nuclear test bed at Idaho National Laboratory (INL) to ultimately improve the integration of microreactors to end-user applications. This ambitious effort seeks to design, authorize, construct, test, and operate the reactor within five years. In order to construct and operate the MARVEL reactor in a timely manner, the system will utilize materials and component designs which have already been used, qualified, or licensed from previous reactors. The MARVEL reactor will be located at the INL Transient Reactor Test (TREAT) facility in the north high-bay equipment pit and will use the existing 304 stainless steel-clad U-ZrH1.6 pin-type fuel system developed by General Atomics and purchased from TRIGA International. This fuel has been previously qualified under the United States Department of Energy’s (US DOE) Reduced Enrichment for Research and Test Reactors (RERTR) Program. Even though the regulator of the MARVEL reactor is the US DOE, the standards and overall approach recommended by the Nuclear Regulatory Commission is well-defined and utilized here. Following NUREG-1537 regulatory guidance, this report documents the authorization case for the MARVEL fuel system’s application to MARVEL and establishes stable and predictable fuel performance during the most thermophysically unfavorable conditions achievable in the MARVEL reactor. To that end, this report provides a comprehensive survey of the known thermophysical properties, performance, and quantitative relationships associated with the MARVEL reactor fuel element and uses this information to determine its mechanical integrity and risk of reaching unacceptable conditions during the most extreme accident scenarios predicted for the reactor using the most conservative assumptions available. The information contained herein is compiled from a combination of historical reports and peer reviewed scientific publication manuscripts. Known mechanisms under which the fuel is susceptible to failure are highlighted and compared to conditions that could exist in the MARVEL reactor during an unanticipated transient or accident scenario. The two scenarios considered for analysis in this report are (1) an unprotected loss of flow accident and (2) a hypothetical unprotected loss of coolant accident during the loss of flow accident. Preliminary 2D steady-state analyses herein indicate that both fuel-cladding chemical interactions and fuel-cladding mechanical interactions are negligible throughout the fuel’s operational cycle under both normal and high temperature accident scenario conditions. Although higher fidelity 3D time-dependent modeling and simulations are planned, the following may be concluded presently. The MARVEL fuel element maintains its geometric stability and structural integrity during the most extreme accident scenarios predicted for the MARVEL reactor. The hoop stress during the unprotected loss of flow accident reaches about -1.27 MPa; this negative stress indicates that it is compressive rather than tensile. The compressive stress is a result of the NaK pressure on the outside of the fuel element, caused by the restricted thermal expansion of the NaK coolant, exceeding the internal pressures generated inside of the fuel element. The hoop stress generated in the cladding during the unprotected loss of coolant accident reaches a maximum of about approximately 10 MPa, which is nearly an order of magnitude less than the predicted yield strength of the cladding under high-temperature accident scenario conditions. Calculations were compared with results from high performance computational simulations using BISON and are in very close agreement. A conservative MARVEL fuel meat peak temperature limit of 900 °C is recommended presently, which is about 180 °C higher than the peak fuel temperature predicted to occur during the most extreme accident. Based on the known properties and behavior of the MARVEL fuel element, the fuel successfully meets its design and safety requirements under normal and most extreme accident conditions with a large safety margin.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Mercury Modeling of TREAT Big-BUSTER Free Field Characterization Experiments

This report summarizes modeling of Big-BUSTER free field characterization (FFC) experiments at the Idaho National Laboratory (INL) Transient Reactor Test Facility (TREAT) reactor performed from December 20th, 2023, to February 22nd, 2024. TREAT is an air-cooled graphite moderated research reactor that can be used to study material response to neutron irradiation. The BUSTER (Broad Use Specimen Transient Experiment Rig) refers to a containment module for placing experiments in the reactor core. The Big-BUSTER is an analogous platform for a modified core configuration with a larger experimental cavity.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2016

TREAT reactor LEU fuel-clad chemical interaction empirical modeling analysis

DOE is converting TREAT (Transient Reactor Test) facility from its existing highly enriched uranium (HEU) core to a low-enriched uranium (LEU) core. In order to assess the magnitude of chemical interaction between fuel and cladding materials during physical contact under expected TREAT operational limits, planned transients tests, and reactivity accident scenarios, a combination of experimental testing and thermodynamic modeling was performed to predict the expected chemical interactions among fuel and cladding chemical constituents. Thermodynamic calculations were then validated with empirical data from experiments that emulate TREAT's expected upper operational limits. Pellet samples composed of LEU oxide powder dispersed in a graphite matrix had intimate contact with zirconium-based alloy cladding. The samples were subjected to long-term isothermal heating under high vacuum. Specimen characterization consisted of scanning electron microscopy, x-ray diffraction analysis, and x-ray tomography. ThermoCalc software and Ellingham's diagrams were used for thermodynamic calculations. The X-ray tomography and SEM analysis of the pellets showed a homogeneous distribution of UO{sub 2} particles within the graphite matrix with isolated larger UO{sub 2} agglomerates. The SEM analysis showed the formation of a lamellar structure between the large UO{sub 2} agglomerate and the graphite matrix. This is an indication that diffusion is taking place at a rather moderate temperature and reaction time during the pellet fabrication. Secondary phases, with high Al and Mg content, were detected inside a UO{sub 2} agglomerate using SEM in SE/EBSD mode and chemical analysis with EDS. LEU feedstock impurities, as Al and Mg, seem to promote the chemical reactivity between UO{sub 2} particles and graphite matrix. XRD analysis of a pellet sample showed the presence of UO{sub 2} and graphite, but no other crystalline phases were detected with this technique. Thermodynamic analysis through the use of Ellingham diagrams showed that within TREAT's operational to reactivity accident temperature (278-820 Celsius degrees), UO{sub 2} can be reduced to U metal by Zr due to a more favorable ΔG for the oxidation of Zr.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

THOR-aLEU Report

The advanced low enriched uranium (aLEU)-THOR experiment vehicle is designed to irradiate fresh fuel rodlet specimens containing UO 2 (uranium dioxide) in the Temperature Heat-sink Overpower Response (THOR) capsule. The goal of the experiments are to compare the behaviors of standard UO 2 pellets to an aLEU concept in which molybdenum (Mo) foils separate UO 2 wafers increasing the thermal conductivity of the fuel. This experiment is designed to be conducted in the Transient Reactor Test facility (TREAT) using the Minimal Activation Retrievable Capsule Holder (MARCH) irradiation system. The goal of these experiments is to assess the effect of thermally conductive inserts in UO 2 by measuring their net effect on radial thermal conductivity using transient nuclear heating and then to determine their power-to-melt threshold in transient overpower ramps. The objective of the aLEU-THOR fuels experiment is to determine the viability and study the performance of UO 2 fuel pellets employing newly upgraded TREAT capability. A novel transient measurement technique will be used with the THOR capsule, which has a solid heat sink to generate the transient temperature gradient for conductivity measurement.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

Specifications of Legacy U(Pu)Zr Metallography Data

The DOE Nuclear Energy Advanced Reactor Technologies (ART) Program has supported the creation of several databases with information describing the safety performance of fast reactors, components, and fuels. This growing collection of legacy experimental data, operating data, and analysis is available online to registered users. Metallography data is one of the most important types of PIE data being collected, organized and stored in several ART Fast Reactor Databases (https://frdb.ne.anl.gov), including the Fuels Irradiation & Physics Database (FIPD), Out-of-Pile Transient Database (OPTD), and TREAT (the Transient Reactor Test Facility) Experimental Relational Database (TREXR). These databases contain three main sets of metallography data. The first set is the metallography data from Experimental Breeder Reactor-II (EBR-II) and Fast Flux Test Facility (FFTF) irradiated fuel pins measured in the Hot Fuel Examination Facility (HFEF); the second set is the metallography data from EBR-II irradiated fuel pins measured in the Alpha-Gamma Hot Cell Facility (AGHCF); the third set is the metallography data from transient tested fuel pins (the transients tests include the out-of-pile tests and TREAT tests) measured in AGHCF. Since both the second and third sets of data were measured in AGHCF, they are governed by the same specification. The metallography data in the databases are digital images scanned from either positive or negative photos. The quality of the images, including their resolution and contrast, relies on the preserved quality of the pictures and the scanning conditions. To analyze the microstructure of a fuel pin, a series of preparatory steps must be undertaken. These include sectioning, epoxy mounting, mechanical grinding and polishing, and often etching. The resulting samples were then transferred to a secondary hot cell, or glovebox (depending the strength of radiation field) for microscopy examination. The specifications provided herein focus on the metallography examinations. The sample grinding, polishing and etching processes are also discussed. The procedures involving sectioning and epoxy mounting are out of the scope of the current specification; details can be found in the corresponding operation manuals. If more data are collected and added to the ART Fast Reactor Databases, this specification will be updated to accommodate the additional data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2019

Characteristics of Fuel Articles for Irradiation Testing in INL-TREAT and MIT-NRL

To obtain valuable data that will help in the design and commissioning of the Transformational Challenge Reactor, a series of graded, increasingly complex irradiation tests are planned that will demonstrate the feasibility of advanced manufactured reactor core components. In the first irradiation test, conventionally- fabricated uranium nitride tristructural isotropic (UN TRISO) fuel kernels will be embedded into compacts that are fabricated using advanced manufacturing methods. These compacts are to be irradiated at Massachusetts Institute of Technology’s Nuclear Reactor Laboratory and Idaho National Laboratory’s Transient Reactor Test Facility. This report presents the characteristics of the proposed samples and experiments.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2019

Select Transient Metallic Fuel Bison Benchmarks

To explore the current capabilities of Bison with respect to transient metallic fuel modeling, four transient experiments are compared with their respective Bison model. The four experiments are the OPT-1 experiment of the Experimental Breeder Reactor II~(EBR-II) and the M5, M6, and M7 experiments of the Transient Reactor Test facility (TREAT). Each benchmark is a 2D-RZ geometry of a single pin employing coupled multiphysics. Bison models of the benchmark agree well and illustrate areas needing development. The areas of suggested development deal with better material models, better coolant channel module for transients, proper treatment of material melting, improved feedback with failure models, and an ability to set initial conditions from post irradiation examination (PIE) data. Two Fast Flux Test Facility (FFTF) pins are also modeled with M7 transient conditions to illustrate Bison being applied to investigate potential experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

Determination of Scale Bar for AGHCF Metallography Data

The DOE Nuclear Energy Advanced Reactor Technologies (ART) Fast Reactor Program (FRP) has supported the development of several databases containing information on the safety performance of fast reactors, components, and fuels. This growing collection of legacy experimental data, operating data, and analysis is available online to registered users. Metallography data represents one of the most critical types of post-irradiation examination (PIE) data being collected, organized, and archived in several ART Fast Reactor Databases (https://frdb.ne.anl.gov), including the Metallic Fuels Irradiation & Physics Database (FIPD), Out-of-Pile Transient Database (OPTD), and TREAT (the Transient Reactor Test Facility) Experimental Relational Database (TREXR). These databases contain three principal sets of metallography data. The first set comprises metallography data from Experimental Breeder Reactor-II (EBR-II) and Fast Flux Test Facility (FFTF) irradiated fuel pins examined in the Hot Fuel Examination Facility (HFEF). The second set consists of metallography data from EBR-II irradiated fuel pins examined in the Alpha-Gamma Hot Cell Facility (AGHCF). The third set includes metallography data from transient-tested fuel pins (including both out-of-pile furnace tests and TREAT tests) examined in AGHCF. Since both the second and third sets were generated in AGHCF, they are governed by identical specifications. The metallography data in the databases consist of digital images scanned from either positive or negative photographic films. To analyze the microstructure of a fuel pin, a series of preparatory steps are required, including sectioning, epoxy mounting, mechanical grinding and polishing, and etching. Following sample preparation, specimens are transferred for metallographic examination. The AGHCF and HFEF metallography data were generated using optical microscopes manufactured by Leitz and Bausch and Lomb (B&L). Images were recorded on Polaroid film at preset magnifications. Magnification verification for the Leitz and B&L metallographs was conducted every two months prior to 1989 and at least every six months from 1989 through the conclusion of the IFR program. Magnifications determined from imaging of microslide standards were compared to the instrument settings for magnifications ranging from 50× to 500×. If the magnifications determined from standards deviated from the instrument settings, adjustments were made to the bellows extension until agreement was achieved. The specifications for AGHCF and HFEF legacy metallography data have been established based on available hard-copy and digital records, most of which have been incorporated into the data repositories associated with FIPD, OPTD, and TREXR. Detailed specifications including hard-copy records, digitized records, cutting diagrams and sectioning schemes, high-magnification photographs, photomosaics (composites), information tags, scale bars, and magnification verification procedures can be found in a separate report.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2025

Griffin Capability Improvements in Support of Ex-core Deep-Penetration Problems

Advanced reactor designs, especially portable reactors that are designed to be located closer to humans and operate autonomously, require the ability to accurately compute the ex-core neutron and gamma flux solutions in terms of shielding design optimization to reduce dose rates at the vessel boundary and detector signal prediction to drive the reactor control system. The Nuclear Energy Advanced Modeling and Simulation program has prioritized improvements to the Griffin discrete ordinates (SN) solver for deep-penetration problems in fiscal year 2025. Significant advancements have been made to the Griffin methodologies for solving ex-core deep-penetration problems for steady-state, fixed-source and transient calculations. This work presents the methodology improvements as well as a comprehensive demonstration with a Transient Test Reactor model and measurements.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2024

Report on RIA Relevant Modified Burst Testing of ATF Cladding Materials

The mechanical performance of accident-tolerant fuel (ATF) cladding candidates in light-water reactors (LWRs) must be similar to or better than that of current conventional nuclear fuel claddings to reduce dose to the public and ensure a that the core coolable geometry is maintained during a postulated reactivity-initiated accident (RIA) in light-water reactors (LWRs). During an RIA event, the rapid thermal expansion of nuclear fuel can deform the cladding once the fuel–cladding gap closes. In some cases, the pellet–cladding mechanical interaction (PCMI) can induce mechanical failure in ATF candidates. Thus, the mechanical response of ATF cladding must be investigated by mimicking the conditions of RIA and potentially performing Transient Reactor Test (TREAT) experiments to establish or verify the safety envelope. The work presented in this report investigated the failure behavior of as-received, hydrided, and chromium-coated (Cr-coated) Zircaloy-4 (Zry-4) cladding tube under strain-driven mechanical conditions, mimicking postulated RIA loading conditions. Mechanical testing was performed at 300°C via modified burst test (MBT) equipment with pulse width control previously developed under the Department of Energy’s (DOE’s) Advanced Fuel Campaign (AFC). The mechanical strains were determined using 2D digital image correlation (DIC) techniques. The base Zry-4 acquired by Cameco Inc. was in stress-relieved annealed (SRA) condition. Because of the observed large deformation of the cladding tubes, the failure strain definition was updated for the MBT, which can also be applied to other tube tests where significant bulging (out-of-plane deformation) is present. The failure strain was determined to be affected by the speed of the test or the RIA event. As the RIA-like event duration decreased from 75 to 15 ms, the failure strain decreased 5, 7 and 1% for as-received, hydrided, and Cr-coated specimens, respectively. Fractography on the Cr-coated specimens indicated the presence of two failure mechanisms: (i) crenulation at the outer surface of the coating due to the tensile tractional forces along with coatings grain microstructure and (ii) formation of critical defect at the coating/cladding interface that initiated coating rupture after severe plastic deformation of the Zry- 4 substrate. Based on the MBT results and fractography observations, performing mechanical property testing at high strain rates—in particular on Cr-coated tubes—and semi-integral TREAT experiments are required future efforts to ensure ATF cladding performance during transients. The testing recommended would also inform the development of long-term generalized cladding technologies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2017

Heat Source Characterization in a TREAT Fuel Particle Using Coupled Neutronics-BCMC Calculations

This work presents a multi-physics, multi-scale approach to modeling the Transient Test Reactor (TREAT) currently prepared for restart at the Idaho National Laboratory. TREAT fuel is made up of microscopic fuel grains (r ˜ 20µm) dispersed in a graphite matrix. The novelty of this work is in coupling a binary collision Monte-Carlo (BCMC) model to the Finite Element based code Moose for solving a microsopic heat-conduction problem whose driving source is provided by the BCMC model tracking fission fragment energy deposition. This microscopic model is driven by a transient, engineering scale neutronics model coupled to an adiabatic heating model. The macroscopic model provides local power densities and neutron energy spectra to the microscpic model. Currently, no feedback from the microscopic to the macroscopic model is considered. TREAT transient 15 is used to exemplify the capabilities of the multi-physics, multi-scale model, and it is found that the average fuel grain temperature differs from the average graphite temperature by 80 K despite the low-power transient. The large temperature difference has strong implications on the Doppler feedback a potential LEU TREAT core would see, and it underpins the need for multi-physics, multi-scale modeling of a TREAT LEU core.

36 MATERIALS SCIENCE↗

DOE OSTI2018

Enhanced geometric capabilities for the transient analysis code T-ReX and its application to simulating TREAT experiments

Here, advances in computational architecture have prompted a resurgence in the simulation of reactor transients from first principles. Most codes are unable to simulate transient events with complex models, and require numerous approximations. The code T-ReX (Transient-Reactor eXperiment simulator), an extensive update to TDKENO, has been developed as a transient analysis tool with few geometric limitations and minimal theoretical approximations. T-ReX achieves this by employing the Improved Quasi-Static (IQS) method to solve the time dependent Boltzmann transport equation with explicit representation of delayed neutrons. The primary change in T-ReX relative to TDKENO is the incorporation of a modified version of the Monte Carlo code KENO-VI to calculate the flux shape and model the geometry of a problem. Using KENO-VI to model systems allows exact representation of the geometry. The changes to T-ReX are verified by comparison of solutions to computational benchmark problems found with a previous version of TDKENO that made use of KENO V.a, and several other codes with time-dependent capabilities. In addition, a three-dimensional model of the Transient Reactor Test Facility (TREAT) core at the Idaho National Laboratory (INL) is constructed with KENO-VI, and used to validate T ReX. T-ReX produces results that agree with benchmark problems, and are in better agreement with TREAT experimental data than TDKENO.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2025

Loss of Flow Conditions in a Modern Pool-type SFR and In-Pile Experiment Design

The metallic fuel safety performance under unprotected design-basis transients is a key consideration for the deployment of advanced sodium fast reactors (SFRs). Reliable data are needed to validate advanced safety codes, reduce uncertainty in cladding failure thresholds, and strengthen confidence in licensing approaches. To address this need, this report develops blueprints for a conceptual sodium loss-of-flow (LOF) experiment in the Mk-IIIR loop at the Transient Reactor Test Facility (TREAT), providing the technical foundation for future integral testing.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗