Search NASA⌕ Search

SEARCH · Search NASA

Results for “ethanol fuel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Model Year 2021 Fuel Economy Guide

The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

2017 EPA fuel economy↗
DOE OSTI2022

Impact of coolant temperature on the combustion characteristics and emissions of a stratified-charge direct-injection spark-ignition engine fueled with E30

The direct injection spark ignition (DISI) engine has received considerable attention due to its potential to increase the power density of traditional spark ignition engines while significantly improving fuel economy through lean, unthrottled combustion. However, the market introduction of DISI engines operated in a lean combustion mode is inhibited by their unsatisfactory emissions, especially during cold start conditions that make proper mixture formation more challenging. Ethanol-blended gasoline, now a widely used fuel, makes the cold start of a DISI engine more difficult, leading to higher HC and soot emissions because of the high latent heat of vaporization of ethanol relative to gasoline. This work investigated the impact of coolant temperature on the characteristics of combustion and emissions in a stratified-charge DISI engine fueled with an E30 fuel (i.e. 30% ethanol in gasoline), while the coolant temperature was alternated between four levels (45, 60, 75, and 90 °C) to simulate different conditions throughout the warm-up process. The experiments showed that the coolant temperature affected the post-spark inflammation time, as well as the speed, intensity, and stability of the combustion process in the engine. When the coolant temperature rose, the engine produced more NOX and less CO, PM and HC. In addition, high-speed direct photography was used to obtain crank-angle resolved images of fuel sprays and flames in the cylinder. As the coolant temperature rose, the liquid spray lengths became shorter, reducing the possibility of wall wetting, and reduced irradiance from soot particles also indicated less nonpremixed combustion. The in-cylinder imaging results are consistent with the observed combustion and emission characteristics and shed light on the underlying processes. Finally, some potential solutions to the emissions challenges faced here could be either raising in-cylinder temperatures by using trapped residuals or modifying the injection schedule, for example by increasing the number of injections or to inject later in the cycle into a higher-density environment.

42 ENGINEERING↗
DOE OSTI2026

Advancing technologies for lignin-based jet fuel production in aqueous phase

Integrating lignin into a cellulosic ethanol plant for the co-production of lignin-based jet fuel (LJF) in aqueous phase offers a significant opportunity to boost operational efficiency, economic viability, carbon conversion, and the overall sustainability of biofuel and chemical production. LJF is lignin-structure-based jet fuel blendstocks primarily composed of alkyl-substituted mono-, bi-, and tri-cyclohexanes. It exhibits high energy density, potential for low emissions, and favourable blend characteristics that comply with drop-in specifications. An overview of lignin feedstock, catalytic processes, LJF chemical compositions, fuel properties tests, and techno-economic analysis (TEA) and life cycle assessment (LCA) indicate that (1) the reactivity of lignin plays a crucial role in its structure transformation to LJF molecules; (2) catalytic processing of lignin to LJF can occur through a simultaneous depolymerization and hydrodeoxygenation process, bypassing the intermediate step of producing and upgrading lignin-derived oil; (3) LJF's uniqueness molecules making it more promising for high energy content and low emission jet fuel properties for next generation sustainable aviation fuel (SAF); and (4) TEA and LCA demonstrate that LJF is not only potentially cost-effective but also offers favourable carbon footprint compared to other SAFs. In conclusion, this review highlights the most recent advancements in LJF technology, along with the challenges and opportunities that lie ahead in fulfilling its potential.

09 BIOMASS FUELS↗
DOE OSTI2021

Alternative Fueling Station Locations

Alternative fueling stations are located throughout the United States and Canada, and their availability continues to grow. The Alternative Fuels Data Center (AFDC) maintains a website where you can find alternative fueling stations near you or on a route, obtain counts of alternative fueling stations by state, view maps, and more. The most recent dataset available for download here provides a "snapshot" of the alternative fueling station information for compressed natural gas (CNG), ethanol (E85), propane/liquefied petroleum gas (LPG), biodiesel (B20 and above), electric vehicle charging, hydrogen, and liquefied natural gas (LNG), as of July 29, 2021.

alt fuel↗
DOE OSTI2020

Supercritical Reforming of Wet Ethanol for High Efficiency Direct-injection Heavy-duty Compression-ignition Engines

The purpose of the research was to investigate the potential of using a mature bio-fuel in heavy-duty compression ignition engines. By co-optimizing both the fuel characteristics and engine system the potential for a superior outcome was demonstrated. The use of wet bio-ethanol eliminates the majority of the energy intensive distilling and dehydrating fuel production processes, which moves the fuel towards carbon neutral and also lowers the fuel costs. The relatively high water content of the resulting fuel is leveraged in the proposed novel combustion system by incorporating an integrated high efficiency exhaust waste heat recovery system. This results in significantly higher thermal efficiency. In addition the combustion system features low criteria pollutant emissions and the potential to reduce the initial cost of the engine system hardware. Substantial societal benefits are demonstrated through the co-optimization of the fuel and engine system. A computational proof-of-concept study has been performed to demonstrate the potential benefits of a novel wet ethanol heavy-duty compression ignition combustion system featuring integrated exhaust waste heat recovery. A combined in-cylinder closed cycle 3D computational fluid dynamics (CFD) - 1D engine system simulation approach was used. The models were validated to baseline engine data using diesel fuel and then applied to the wet ethanol study. The original concept was to maximize exhaust waste heat recovery through supercritical reforming of the wet ethanol fuel. Phase I simulation results indicated that the optimal solution for maximum engine efficiency gains were realized through maximizing thermo-mechanical recuperation with negligible fuel reformation. The results show the potential to achieve impressive gains in brake thermal efficiency (BTE) over the base diesel engine. The potential to increase BTE up to 20.9% over the base diesel engine was demonstrated, with even larger gains possible through reduced in-cylinder heat transfer losses. The majority of the efficiency gains were realized through integrated high efficiency exhaust waste heat recovery. The concept also has the potential to achieve future ultra-low NO x emissions standards and negligible engine-out soot emissions. The mixing controlled combustion of high temperature wet ethanol features relatively low engine-out NO x emissions without the need for exhaust gas recirculation (EGR). The soot free combustion enabled by the relatively high oxygen content of ethanol also allows for the use of stoichiometric mixing controlled combustion, which is not practical with diesel fuel. When stoichiometric combustion is used a simple passive 3-way catalyst can be used for exhaust emissions after-treatment and near zero tailpipe emissions. The Phase I simulations results have defined the system layout and requirements in preparation for the Phase II experimental proof-of-concept study. The potential applications of the research include most current applications of diesel engines. The Phase I study focused on heavy-duty on-highway class 8 trucks. However, virtually any application that requires highly efficient clean power generation would benefit from the novel engine system proposed. The results indicate substantial fuel cost savings and reduced greenhouse gas emissions with similar or reduced initial system hardware costs compared to modern diesel engine systems.

09 BIOMASS FUELS↗
DOE OSTI2025

Development of a Flex-Fuel Mixing Controlled Combustion System for Gasoline/Ethanol Blends Enabled by Prechamber Ignition

This project demonstrated a heavy-duty engine converted from using diesel fuel to a flex-fuel engine that can use any blend of gasoline and ethanol. The combustion system is an innovative concept that allows very low cetane fuels to be used in a conventional mixing-controlled combustion (MCC) strategy without auxiliary heating, changes to the basic engine structure, or advanced controls.

09 BIOMASS FUELS↗
DOE OSTI2020

Carbon Cycling, Environmental & Rural Economic Impacts of Collecting & Processing Specific Woody Feedstocks in Biofuels

Woody biomass will be an essential feedstock for a large-scale cellulosic biofuel industry. The life cycle carbon accounting for the production of biofuels from woody feedstocks is complex and has engendered significant controversy. Issues such as below ground carbon, carbon debt, varied regional forest practices, multiple parallel forest product lines, and development of realistic counterfactual scenarios all contribute to the complexity. DOE funded CORRIM to develop comprehensive and definitive lifecycle inventories and assessments on the production of fuels from woody feedstocks. CORRIM brought together expertise in forest practices, short rotation woody crops, bioconversion of woody biomass, process modeling, and life cycle assessment to successfully accomplish this goal. The CORRIM team has developed data on forest productivity, fuel usage, and fuel production for six regionally specific forest systems. These six forest systems include three current commercial systems; southern pine plantations, Douglas-fir plantations, naturally regenerated Northeastern (NE) spruce/fir, and three ‘short rotation woody crops’, poplar, eucalyptus and willow, which are at different stages of demonstration in the US. The fuel production systems include cellulosic ethanol and bio-oil based hydrocarbons. The project was successfully reviewed at the BETO Program review in March 2015, 2017, and 2019 and has resulted currently in 19 publications and reports and 35 presentations at both national and international conferences, with more in the pipeline. See publications and presentations for links to each document. Finally, and most importantly, CORRIM has gone beyond the scope of the original DOE proposal to work closely with GREET at Argonne National Laboratory (ANL) to incorporate all the life cycle data and scenario models into their modeling system. GREET is the most widely used and definitive information source for evaluating lifecycle carbon emissions for fuels. The incorporation of CORRIM data from this project guarantees the results of the research will be extensively used and widely disseminated. Technical process improvements and policy relevant accomplishments are detailed in the relevant programmatic sections in the full report including citations therein. Highlights are summarized here for easy reference.

09 BIOMASS FUELS↗
DOE OSTI2022

Direct Air Capture of CO 2 and Delivery to Photobioreactors for Algal Biofuel Production (Final Report)

A mobile DAC system was designed and constructed to pair with photobioreactors growing algae for biofuel production. The DAC system was designed as a versatile research system, rather than a compact production unit. The system was constructed and mounted on a mobile skid to facilitate transportation to the algae production site. Within the DAC system, CO 2 was captured using amine-loaded monoliths that allow for high CO 2 uptake with low pressure drop. The CO 2 is collected using a Global Thermostat patented temperature/vacuum swing adsorption (TVSA) process. Amine sorbents and process conditions were optimized to produce 10 to >20 g CO 2 .h-1. The stability of the amine sorbents was also studied, with sorbent modifications made to improve stability to degradation by oxidation. An Algenol-developed Spirulina strain (Arthrospira platensis AB2293) was selected as the production cyanobacterial strain. AB2293 cultured was inoculum for outdoor production following PBR installation by Algenol. The PBR system was composed of three independent PBRs, with each PBR composed of four hanging bags internally recirculated by a liquid turnover pump. The PBRs were operated outdoors in Atlanta, GA, and integrated with the DAC system. Algae were grown with similar productivity using DAC-CO 2 as algae grown using pure CO 2 obtained commercially (Airgas). Throughout the experimental duration, no discoloration was observed, and cellular morphology was consistent between the two experimental treatments. An LCA including lifecycle greenhouse gas emissions, full life cycle inventory of the Algenol system and the DAC system and integrated DAC+PBR system was developed. Lifecycle greenhouse gas emissions were calculated for capture of carbon dioxide using input from Global Thermostat and the National Renewable Energy Laboratory. Three scenarios for energy provision were evaluated: a natural gas combined heat and power system sized to meet the electricity requirement, a natural gas combined heat and power system sized to meet the process heat requirements, and a system without on-site power that procures the electricity from the grid. In all three cases, as expected, the major contributor to the emissions is the energy consumption associated with the desorption step of the DAC process. The LCA quantified the reduced potential energy and greenhouse gas emissions of heat and mass integration of DAC and Algenol compared to unintegrated DAC and Algenol systems. A life cycle assessment of the role of sorbent productivity and lifetime was also developed. The development of more robust, oxidation resistant DAC sorbents may enable small reductions in energy requirements and in lifecycle greenhouse gas emissions and other environmental impacts. NREL performed techno-economic analysis (TEA) to identify the integration scenario most likely to achieve a 15% cost reduction target versus the baseline. Heat and mass integration of DAC and the PBR is critical to minimizing the MFSP. The baseline case utilizes no heat and mass integration, and the DAC system provides 100% of the CO 2 required by the photobioreactors (20 tonnes/hr), operating for 12 hours/day capturing 40 tonnes CO 2 /operating hour. The minimum fuel selling price (MFSP) of ethanol calculated from the baseline case was $10.68/gal ethanol. This corresponds with a targeted MFSP of $9.07/gal ethanol (or 15% reduction). This target was achieved by integration Option 2a with the greatest cost reduction of 17.8% (or $8.78/gal) and integration Option 2b with a cost reduction of 16.4% (or $8.93/gal). Reductions in MFSP are attributed to two primary process considerations: (a) CO 2 storage at night reduces the capital expenses associated with DAC (i.e., increasing on-stream time); and (b) distributed DAC scenarios (DAC-PBR integration Options 2a and 2b) make use of boiler and DAC CHP flue gas CO 2 (free). Direct air capture on-stream time was one of the largest contributors to MFSP reduction.

09 BIOMASS FUELS↗
DOE OSTI2021

Copper Dendrites and Surface Engineering for Enhanced CO2 Reduction Research Report Paper

The electrocatalytic reduction of CO 2 (CO 2 R) into hydrocarbon fuels, such as ethylene and ethanol, provides an attractive pathway towards closing the industrial carbon cycle and producing chemicals using renewable electricity. Existing CO 2 R technologies can exhibit C 2+ product selectivity above 74% and operating current densities over 1.3 A/cm 2 , but none can achieve both simultaneously, limiting the commercial viability and scalability of this technology. Low CO 2 concentrations at the catalyst surface and competing side reactions such as the hydrogen evolution reaction (HER) inhibit C 2+ faradaic efficiencies and operational current densities. Additionally, the use of high surface area cathode geometries to increase operational current densities is under-investigated. In this work, we electrodeposit a macroporous copper dendrite film to form high surface area cathodes. These structures are then coated with a combination of hydrophobic/hydrophilic ionomers to achieve high electrochemically active surface areas (ECSA), form regions of intrinsic porosity, and maximize catalytic availability of CO 2 . Using these techniques, we hope to maximize C 2+ faradaic efficiencies (FE) and geometric partial current densities. The treated cathode compound macrostructure (~10μm-sized pores, and ~μm-long dendrites) and concomitant surface area allows increased geometric current densities while the ionomer coating simultaneously inhibits HER and increases hydrogen availability to improve C 2+ selectivity. Our results show that careful engineering of the catalyst-electrolyte interface can enhance CO 2 reduction product selectivity and efficiency.

10 SYNTHETIC FUELS↗
DOE OSTI2020

Mechanistic understanding of catalytic conversion of ethanol to 1-butene over 2D-pillared MFI zeolite

Ethanol is an important C2 platform molecule for producing value-added chemicals and distillate hydrocarbon fuels (e.g., jet and diesel). Among these, catalytic upgrading of ethanol to butenes can generate valuable commodity chemicals (e.g., 1-butene) and provide C4 olefin intermediates that can be further upgraded to jet/diesel fuels. 2D zeolites offer hierarchical mesoporous structures, leading to improved mass transport and reduced diffusion length, which can help to address the coking challenges faced by ethanol conversion to hydrocarbons over 3D zeolites. In this study, we investigate the acid-catalyzed conversion of ethanol to 1-butene over the Brønsted acid sites (BAS) in 2D-pillared MFI zeolite (2D-PMFI) using ab initio molecular dynamics (AIMD) simulations, in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), and calorimetric measurements. A detailed thermodynamic analysis, using quasi-harmonic approximation (QHA), on the Gibbs free energy pathway of ethanol conversion shows that the consideration of entropy is critical to accurately capture the detailed thermodynamic profiles. The formation of bulky ethoxy-ethene complex is found to be a potential rate-determining step (RDS), proceeding via stepwise mechanism. The reactivity of 2D-PMFI can be further tuned by manipulating RDS through a careful control of number of BAS and operating temperatures. The accuracy of computational model is confirmed through the comparison of calculated vibrational density of states (VDOS) against the experimental DRIFTS measurements. Overall, our study provides mechanistic insights into ethanol upgrading over the 2D-PMFI and shows the importance of evaluating entropic effects in such confined system.

Ethanol conversion, 2D-pillared zeolite, MFI, Anha↗
DOE OSTI2021

The U.S. Energy System and the Production of Sustainable Aviation Fuel From Clean Electricity

Jet fuel is relatively small in terms of energy consumption and carbon dioxide emissions (10% of U.S. transportation sector in 2021, expected to increase to 14% by 2050). Still airlines have ambitious goals to reduce their greenhouse footprints from carbon-neutral growth beginning this year to reducing greenhouse gas emission for international flights by 50% by 2050 compared to 2005 levels. The challenge is heightened by the longevity of the current fleet (30–50 years) and by the difficulty in electrifying the future fleet because only 5% of the commercial aviation greenhouse gas footprint is from regional flights that might, conceivably be electrified using foreseeable technology. Therefore, large amounts of sustainable aviation fuel will be needed to reach the aggressive targets set by airlines. Only 3 million gallons (11.4 ML) of sustainable aviation fuel (SAF) (with a heat of combustion totaling about 400 TJ = 0.0004 EJ) was produced in the U.S. in 2019 for a 26 billion gallon per year market (3.6 EJ/year). Fischer-Tropsch and ethanol oligomerization (alcohol-to-jet) are considered for producing SAF, including the use of renewable electricity and carbon dioxide. In sequencing the energy transition, cleaning the U.S. grid is an important first step to have the largest greenhouse gas emissions reduction. While carbon dioxide and clean electricity can potentially provide the SAF in the future, an ethanol oligomerization option will require less energy.

25 ENERGY STORAGE↗
DOE OSTI2021

Cell-free synthetic biochemistry upgrading of ethanol to 1,3 butanediol

It is now possible to efficiently fix flue gas CO/CO 2 into ethanol using acetogens, thereby making carbon negative ethanol. While the ethanol could be burned as a fuel, returning the CO 2 to the atmosphere, it might also be possible to use the fixed carbon in more diverse chemicals, thereby keeping it fixed. Here we describe a simple synthetic biochemistry approach for converting carbon negative ethanol into the synthetic building block chemical 1,3 butanediol (1,3-BDO). The pathway completely conserves carbon from ethanol and can ultimately be powered electrochemically via formate oxidation. Our proof-of-principle system reached a maximum productivity of 0.16 g/L/h and, with replenishment of feedstock and enzymes, achieved a titer of 7.7 g/L. We identify a number of elements that can be addressed in future work to improve both cell-free and cell-based production of 1,3-BDO.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Technical and economic feasibility of an integrated ethanol and anthocyanin coproduction process using purple corn stover

The coproduction of high-value anthocyanin extract in the cellulosic ethanol process would diversify the co-product market, increase revenue, and potentially improve the economics of the process. The high anthocyanin concentration in the cob and structural carbohydrates in residual stover make purple corn stover an attractive source for anthocyanin and ethanol coproduction. In this study, we aimed to develop simulation models for processes integrating ethanol production and anthocyanin extraction using purple corn stover, to evaluate their techno-economic feasibility, and to compare their performance with the conventional ethanol production process using corn stover. The annual ethanol production for plants processing 2000 MT dry feedstock / day was 148.6 million L/year for the integrated processes compared with 222.6 million L/year for the conventional process. Anthocyanin production in the modified processes using dilute acid-based and water-based anthocyanin extraction processes was 1779 and 1099 MT/year, respectively. Capital investments for the integrated processes ($\$448.1$ to $\$443.8$ million) were higher than the conventional process ($\$371.9$ million). Due to high revenue from anthocyanin extract, the ethanol production cost for the integrated process using acid-based anthocyanin extraction ($\$0.36$/L) was 34.5% lower than conventional ethanol production ($\$0.55$/L). The ethanol production cost for the integrated process using water-based anthocyanin extraction ($\$0.68$/L) was higher than conventional ethanol production due to low ethanol and anthocyanin yields. The minimum ethanol selling price for the integrated process using acid-based anthocyanin extraction ($\$0.65$/L) was also lower than the conventional process ($\$0.72$/L), indicating an improvement in economic performance.

09 BIOMASS FUELS↗
DOE OSTI2024

Effect of Cyclo-Pentane Impurities on the Autoignition Reactivity and Properties of a Gasoline Surrogate Fuel

Surrogate fuels that reproduce the characteristics of full-boiling range fuels are key tools to enable numerical simulations of fuel-related processes and ensure reproducibility of experiments by eliminating batch-to-batch variability. Within the PACE initiative, a surrogate fuel for regular-grade E10 (10%vol ethanol) gasoline representative of a U.S. market gasoline, termed PACE-20, was developed and adopted as baseline fuel for the consortium. Although extensive testing demonstrated that PACE-20 replicates the properties and combustion behavior of the full-boiling range gasoline, several concerns arose regarding the purity level required for the species that compose PACE-20. This is particularly important for cyclo-pentane, since commercial-grade cyclo-pentane typically shows 60%–85% purity. Here, in the present work, the effects of the purity level of cyclo-pentane on the properties and combustion characteristics of PACE-20 were studied. Chemical kinetic simulations were performed to predict the effects of cyclo-pentane impurities on the properties, octane rating, and autoignition reactivity under homogeneous charge compression-ignition conditions of PACE-20. From the numerical results, cyclo-pentane with 85% purity or higher is required to reasonably match both the research octane number and motor octane number of the target gasoline. Finally, homogeneous charge compression-ignition engine simulations show that impurities have only a modest effect on reactivity at naturally aspirated conditions, but cyclo-pentane purity is critical to properly replicate the pressure dependency of the reactivity.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Decarbonizing Hydrogen Production: Assessing A Net-Negative Pathway

Hydrogen is gaining prominence as a key factor in the world's transition to a cleaner energy future. The International Energy Agency (IEA)'s Global Hydrogen Review 2023 reports that the number of low-emission hydrogen production projects is increasing rapidly. The potential for growth in new applications such as heavy industry, transportation, and power generation is significant. The IEA urges more decisive action to spur demand for low-emission hydrogen to achieve climate goals. While hydrogen is produced through various industrial methods, each with its own advantages and disadvantages, low-carbon hydrogen is critical for mitigating climate change and is incentivized by the Clean Hydrogen Production Tax Credit (45V). To this end, we have evaluated a commercial technology that can produce low- or negative-carbon hydrogen via ethanol catalytic oxidative reforming. This study assessed life cycle greenhouse gas emissions (carbon intensity or CI) associated with the hydrogen production technology. A total of 24 scenarios were evaluated, encompassing (a) Gen1 versus Gen2 ethanol inputs, (b) carbon capture and sequestration (CCS) of upstream fermentation CO2, and (c) oxygen sourcing via air separation unit (ASU) versus purchased or on-site production of oxygen as a byproduct of hydrogen electrolysis with a proton exchange membrane (PEM). Key findings include that the base case CI for hydrogen production using Gen2 ethanol from corn stover is lower than Gen1 dry mill corn ethanol. The study also points out that the CI for hydrogen production using PEM-O2 is lower than that using ASU-O2, whether the PEM-O2 is produced on-site or off-site (importing). When sourcing oxygen from on-site PEM-O2, the Gen1 and Gen2 ethanol-derived hydrogen exhibit favorable net-negative CI values for all evaluated scenarios, especially if the upstream ethanol CCS is included. As a reference, the 45V regulatory threshold for generating clean hydrogen tax credits is a CI below 0.45 kg CO2e/kg hydrogen.

BIOMASS FUELS,HYDROGEN↗
DOE OSTI2021

Conversion of High-Solids Hydrothermally Pretreated Bioenergy Sorghum to Lipids and Ethanol Using Yeast Cultures

Glucose and xylose are the major sugars in cellulosic hydrolysates. The cellulosic sugars can be used for the production of biofuels and value-added bioproducts. In this study, lipid and ethanol were produced from bioenergy sorghum syrups using engineered yeasts. Here, bioenergy sorghum was hydrothermally pretreated at 50% solids loading in a continuous reactor system and mechanically refined sequentially using a burr mill to improve biomass accessibility for hydrolysis. Fed-batch enzymatic hydrolysis was conducted with 50% w/v solids loading to achieve 230 g/L sugar concentration. Different strains of Rhodosporidium toruloides were used to ferment sugars into lipids, and the highest lipid yield of 9.2 g/L was observed. The lipid yield was improved to 19.0 g/l by implementing a two-stage culture where once the sugars were exhausted in the first stage, the yeast was introduced into fresh hydrolysate without adding nitrogen. For ethanol production, the engineered Saccharomyces cerevisiae SR8ΔADH6 was utilized to coferment glucose and xylose. Additionally, the effects of nutrient media (YP, YNB/urea, and urea), cellulosic sugar concentration, and sulfite addition were investigated to optimize the ethanol yield from sorghum syrups. The optimal ethanol yield at 73.3% was obtained from the YNB/urea culture consisting of 34 g glucose/L and 17 g xylose/L.

09 BIOMASS FUELS↗
DOE OSTI2025

A distinct class of ferredoxin:NADP + oxidoreductase enzymes driving thermophilic ethanol production

Biofuel production from lignocellulosic biomass offers a transformative solution to reduce global fossil fuel dependency. Certain thermophilic anaerobes, including Clostridium thermocellum, show promise for renewable ethanol production due to their ability to break down plant material at high temperatures. However, achieving commercially viable ethanol yields has proven challenging despite extensive engineering efforts. Here, we characterized 27 ferredoxin:NADP + oxidoreductase (Fnor) enzymes for their enzyme activity, nicotinamide cofactor specificity, thermotolerance, and functional expression in C. thermocellum . We identified a subset of 10 of these enzymes as a novel class of Fnor enzymes suited for metabolic pathways aimed at high-titer ethanol production. When expressed in engineered C. thermocellum , these enzymes increased ethanol production up to 2.2-fold. These findings establish a novel ethanol pathway and provide insights into physiological roles and biotechnological applications of this new class of Fnor enzymes.

09 BIOMASS FUELS↗
DOE OSTI2025

Cradle-to-Gate greenhouse gas emissions of the production of ethylene from U.S. Corn ethanol and comparison to fossil-derived ethylene production

Conventional ethylene production heavily depends on fossil-derived feedstocks via steam cracking, a very energy- and emission-intensive process. Researchers have been exploring alternatives to reduce CO 2 emissions including producing ethylene from biobased feedstocks. This paper evaluates the cradle-to-gate greenhouse gas (GHG) emissions of bioethylene produced from U.S. corn ethanol. The analysis includes different pathways for the dehydration of corn ethanol to ethylene and co-processing routes via fluid catalytic cracking (FCC) processes. For the FCC co-processing route carbon-14 analysis is used to determine bioethanol yields. A 127% reduction in life cycle GHG emissions of bioethylene is estimated compared to fossil-derived ethylene for the base case. Additional case studies are also discussed to understand the reduction of GHG emissions due to sustainable corn farming and renewable power use, biogenic carbon capture, and fuel switch with biofuels at the ethanol plant, and its impact on bioethylene GHG emissions.

carbon footprint↗