Search NASA⌕ Search

SEARCH · Search NASA

Results for “graphite microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Dynamic In‐Plane Heterogeneous and Inverted Response of Graphite to Fast Charging and Discharging Conditions in Lithium‐Ion Pouch Cells

Solutions for improving fast charging of lithium‐ion batteries have largely focused on alleviating through‐plane lithiation gradients while little is understood about in‐plane heterogeneities and how to resolve them. Herein, high‐speed synchrotron X‐ray diffraction (XRD) resolves graphite lithiation spatially and temporally during 6 C charging and 2 C discharging. At every point during operation, considerable differences in the state of lithiation across the pouch cell are present. Some regions are more responsive to operation than others, reaching full lithiation early during charge and full delithiation during discharge. Other regions within the cell never fully delithiate during discharge, despite a prolonged voltage hold at 2.8 V. Using time‐resolved XRD data, the calculated local current density (mA cm −2 ) at the graphite surface shows an unexpected occurrence of local inverted current densities where regions of graphite are observed to delithiate during charging and lithiate during discharging. A pseudo‐3D model is developed for the graphite electrode with spatially varying microstructural tortuosity to show how microstructural heterogeneity could influence spatial charge dynamics. The model could not predict the complex in‐plane charge behavior observed within the cell. Consequently physics‐based charging protocols based on homogeneous electrode assumptions may underestimate the local variations in charge dynamics and occurrence of lithium plating.

25 ENERGY STORAGE↗

On the Solidification and Structure Formation during Casting of Large Inserts in Ferritic Nodular Cast Iron

The graphite nodule count and size distributions for boiling water reactor (BWR) and pressurized water reactor (PWR) inserts were investigated by taking samples at heights of 2160 and 1150 mm, respectively. In each cross section, two locations were taken into consideration for both the microstructural and solidification modeling. The numerical solidification modeling was performed in a two-dimensional model by considering the nucleation and growth in eutectic ductile cast iron. The microstructural results reveal that the nodule size and count distribution along the cross sections are different in each location for both inserts. Finer graphite nodules appear in the thinner sections and close to the mold walls. The coarser nodules are distributed mostly in the last solidified location. The simulation result indicates that the finer nodules are related to a higher cooling rate and a lower degree of microsegregation, whereas the coarser nodules are related to a lower cooling rate and a higher degree of microsegregation. The solidification time interval and the last solidifying locations in the BWR and PWR are also different.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Fullerene-like defects in high-temperature neutron-irradiated nuclear graphite

Irradiation-induced defect evolution in graphite is particularly important for its application in graphite-moderated nuclear reactors. The evolution of defects directly influences macroscopically observed property changes in irradiated nuclear graphite which, in turn, can govern the lifetime of graphite components. This article reports novel defect structures and the irradiation response of microstructural features occurring in high-temperature irradiated nuclear graphite IG-110. High resolution transmission electron microscopy (HRTEM) was used to characterize specimens neutron-irradiated at a high temperature (≥ 800°C) at doses of 1.73 and 3.56 atomic displacements per atom (dpa). Concentric shelled and fullerene-like defects were found to result in swelling along the c-axis and contraction along the a/b-axis of crystallites. Furthermore, such defects are shown to occur within, and partially fill, Mrozowski cracks prior to turnaround dose. In addition, in situ TEM under similar irradiation conditions was used to capture the real-time dynamic evolution of defects, providing unambiguous analysis of the evolution of the graphite structures during irradiation. Here, the results suggest the mainstream theory for radiation damage in nuclear graphite (which assumes additional basal plane formation as the sole reason) to be an incorrect interpretation of defect evolution contributing to irradiation-induced property changes at higher temperatures.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Features of Pulsed Laser Annealing of BC{sub 3} Films on a Sapphire Substrate

The morphology, chemical composition, microstructure, and electrical properties of BC{sub 3} thin films subjected to melting by a nanosecond laser pulse are investigated. The original films have been created by pulsed laser codeposition of B and C onto a sapphire substrate at 150 and 350°C. Morphological changes in the films depended on their initial structural state. However, a “frozen” structure of both films after irradiation corresponded to the B-saturated graphite-like phase, the local composition of which varied due to the formation of inclusions of amorphous boron carbide. Before and after irradiation, the films exhibited a slightly decreasing dependence of the surface resistance with increasing temperature from 4.2 to 330 K. After laser irradiation, the films resistance has decreased by a factor of ~2.6.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Understanding the reaction of nuclear graphite with molecular oxygen: Kinetics, transport, and structural evolution

A thorough understanding of oxidation is important when considering the health and integrity of graphite components in graphite reactors. For the next generation of graphite reactors, HTGRs specifically, an unlikely air ingress has been deemed significant enough to have made its way into the licensing applications of many international licensing bodies. While a substantial body of literature exists on nuclear graphite oxidation in the presence of molecular oxygen and significant efforts have been made to characterize oxidation kinetics of various grades, the value of existing information is somewhat limited. Often, multiple competing processes, including reaction kinetics, mass transfer, and microstructural evolution, are lumped together into a single rate expression that limits the ability to translate this information to different conditions. This article reviews the reaction of graphite with molecular oxygen in terms of the reaction kinetics, gas transport, and microstructural evolution of graphite. It also presents the foundations of a model for the graphite-molecular oxygen reaction system that is kinetically independent of graphite grade, and is capable of describing both the bulk and local oxidation rates under a wide range of conditions applicable to air-ingress.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermal oxidation of nuclear graphite and pyrolytic carbon coatings

The oxidation of pyrolytic carbon (PyC) deposited via fluidized bed chemical vapor deposition was characterized and compared with that of standard nuclear-grade graphite. The materials were heated at 700 to 1000 °C in a thermogravimetric analysis system under 20% v/v O 2 flow, allowing for direct comparison of dynamic oxidative mass change in each material. Further, three different PyC samples fabricated under different conditions exhibited variation in total mass loss and mass loss rate, varying by as much as 709 mg/cm 2 in total mass loss and 14.2 (mg/cm 2 )/min in mass loss rate at a single temperature. These variations highlight the correlation between PyC microstructure/defect density and oxidation susceptibility. Additionally, changes in the microstructure and composition between PyC and graphite were characterized via scanning electron microscopy and correlated to the mass loss results. The results of this work have implications toward the safety of tristructural isotropic (TRISO) and other coated particle fuels, especially under off-normal conditions, given the limited information that exists about the oxidation behavior of PyC.

36 MATERIALS SCIENCE↗

Solid-state reaction mediated microstructural evolution in a spark plasma sintered in situ Ti–B 4 C composite

For this study, a novel porosity-free in situ Ti–B 4 C composite was fabricated via spark plasma sintering (SPS). Detailed analysis of the phase evolution, coupling results from XRM, XRD and SEM-EBSD-EDS, indicate that primarily TiB 2 precipitates formed due to the in-situ reactions between the boron-carbide and titanium powders. The precipitation of TiB 2 resulted in the formation of a graphitic C-rich thin layer circumscribing the partially reacted B 4 C particles. Further progression of the in-situ reaction leads to the out-diffusion of the excess carbon from the B 4 C particles, across the graphite and TiB 2 phases, forming TiC upon reacting with the titanium matrix. Therefore, the final microstructure primarily consisted of TiB 2 , TiC, and partially reacted B 4 C phases, with small amounts of TiB, α-Ti, and graphite. Furthermore, the microstructure in these SPS processed in situ composites appeared to be the product of a solid-state Ti–B 4 C diffusion couple, substantially different from their fusion-based additively manufactured counterparts. Nano-indentation tests revealed a remarkably high average hardness of ~25 GPa for this SPS-processed Ti–B 4 C composite and comparable (with literature) phase-specific hardness and modulus values for the constituent TiB 2 , TiC, and B 4 C phases.

36 MATERIALS SCIENCE↗

Radiation damage study of POCO ZXF-5Q graphite for neutrino production targets using 4.5 MeV helium ions

To address the challenges of increased beam power and target survivability associated with next-generation particle production beam lines, high dose, high-energy proton beam conditions are simulated using irradiation from low-energy ion beams. A low-energy ion irradiation study of POCO ZXF-5Q graphite under conditions similar to those of the NuMI NT-02 neutrino production target at the Fermi National Accelerator Laboratory is reported. Helium ion irradiation was performed at 100 ∘ C to a maximum damage level of 0.9 displacements per atom (DPA). Irradiation induced hardening, swelling of the irradiated region, inter-plane lattice expansion, and intraplane lattice contraction with increasing ion fluence was observed using micromechanical (nanoindentation, atomic force microscopy) and electron microscopy (high-resolution imaging, selected area diffraction) characterization. Similar changes were also observed in post irradiation examination of the NT-02 target indicating that ion irradiation can be a valuable tool for estimating radiation damage in proton beam targets. Caution must be exercised though, because the hardening, lattice alteration, and swelling occur to different magnitudes for a given damage level. The observed hardening and embrittlement were greater for ion irradiated graphite. For He ion irradiated samples the lattice spacing changes were smaller at low damage levels (78% less expansion and 71% less contraction at 0.1 DPA) and larger at high damage levels (38% more expansion and 5% more contraction at 0.9 DPA) relative to that observed in the NT-02 target. The magnitude of swelling was 8.5× greater under ion irradiation which is influenced by the differing damage gradients and inclusion of implanted He ions in the region of interest.

43 PARTICLE ACCELERATORS↗

Graphite oxide-mediated synthesis of porous CeO{sub 2} quadrangular prisms and their high-efficiency adsorptive performance

Graphical abstract: - Highlights: • Porous CeO{sub 2} quadrangular prisms have been prepared via graphite oxide-mediated synthesis. • Dual-pore hierarchical systems are formed with the pore distributions around 4 nm and 30 nm. • Porous CeO{sub 2} exhibits a rapid adsorption to Rhodamine B with a removal efficiency of ∼99%. • Porous CeO{sub 2} retains the same performances in different pH solutions. - Abstract: We report a graphite oxide-mediated approach for synthesizing porous CeO{sub 2} through a facile hydrothermal process followed by thermal annealing in air. The phase structure, morphology, microstructure and porosity of the products have been revealed by a combination of X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and N{sub 2} adsorption. The as-prepared CeO{sub 2} products show well-defined quadrangular prism morphology, and they are composed of interconnected nanoparticles with diameters around 30–100 nm. In particular, the dual-pore hierarchical systems are created in the CeO{sub 2} quadrangular prisms with the pore distributions around 4 nm and 30 nm. The dye sorption capacity of the porous CeO{sub 2} is investigated, which exhibits a rapid adsorption to rhodamine B with a high removal efficiency of ∼99%. Moreover, the CeO{sub 2} absorbent retains the same performances in different pH solutions.

36 MATERIALS SCIENCE↗

The Mechanical Properties of Energetically Deposited Non-Crystalline Carbon Thin Films

The mechanical behaviour of carbon films prepared with a variety of densities and microstructures was investigated using nanoindentation. Deposition energies between 25 and 600 eV and temperatures in the range 25-600 °C were used. Films prepared at low temperatures and moderate energy were amorphous with a high density. Finite element methods were used to model the stress fields, reproduce the indentation behaviour and evaluate elastic properties. Young s moduli up to 670 GPa and a low Poisson s ratio of ~ 0.17 were found, comparable to polycrystalline cubic boron nitride, one of the hardest materials known. Films with the same density did not always show the same behaviour, emphasising the role of microstructure in determining mechanical response. Extended graphite- like regions within the films grown at high energy and high temperature observed in transmission electron microscopy caused plastic deformation and failure to recover after a complete indentation cycle. At low deposition energies, the graphite-like regions were smaller in size causing plastic deformation but with complete recovery after indentation.

36 MATERIALS SCIENCE↗

Low-temperature synthesis of AlN powder with multicomponent additive systems by carbothermal reduction-nitridation method

AlN powders were synthesized at low temperatures (1300 and 1400 {sup o}C) by the carbothermal reduction-nitridation (CRN) method using multicomponent additive systems. The synthesis treatments were conducted in a graphite furnace with flowing nitrogen gas between 1200 and 1500 {sup o}C using powder mixtures with Al{sub 2}O{sub 3}:C molar ratio of 1:3 and 0.5-3 wt% of CaF{sub 2}, Y{sub 2}O{sub 3}, Li{sub 2}CO{sub 3} and/or SrCO{sub 3} as additives. In relation to the conventional CRN process, the use of multicomponent additive systems reduced the synthesis temperature in 200 {sup o}C (CaF{sub 2}-SrCO{sub 3}), 100 {sup o}C (CaF{sub 2}-Li{sub 2}CO{sub 3} and CaF{sub 2}-Y{sub 2}O{sub 3}-Li{sub 2}CO{sub 3}) or <100 {sup o}C (CaF{sub 2}-Y{sub 2}O{sub 3} and CaF{sub 2}-Y{sub 2}O{sub 3}-Li{sub 2}CO{sub 3}-SrCO{sub 3}). X-ray diffraction patterns showed that the additives reacted with the alumina powder forming aluminate phases, which vaporized with the increase of synthesis temperature. The enhanced AlN conversion rate was discussed in terms of the vaporization of aluminates in the reducing atmosphere.

36 MATERIALS SCIENCE↗

Honeycomb-like graphitic ordered macroporous carbon prepared by pyrolysis of ammonium bicarbonate

Graphical abstract: Honeycomb-like graphitic macroporous carbon (HGMC) with big pores centered at 1-3 {mu}m, has been prepared by controlling the reaction temperature and amount of NH{sub 4}HCO{sub 3} at 550 {sup o}C in a sealed reaction system. Possible formation processes of HGMC are discussed on the experimental results. It is believed that the in situ formed MgO microparticles play a template role during the preparation of HGMC. Highlights: {yields} Honeycomb-like graphitic carbon was synthesized at 550 {sup o}C. {yields} The honeycomb-like graphitic carbon is macroposous structures. {yields} The formed MgO microparticles play a template role during the HGMC formation. {yields} The method can be expended to synthesize other porous or hollow carbon material. -- Abstract: Honeycomb-like graphitic macroporous carbon (HGMC) was synthesized by means of pyrolysis of NH{sub 4}HCO{sub 3} using Mg powder as reductant in an autoclave at 550 {sup o}C. The characterization of structure and morphology was carried out by X-ray diffraction (XRD), Raman spectrum, field-emission scanning electron microscopy (FESEM), and (High-resolution) transmission electron microscope [(HR)TEM]. The results of nitrogen adsorption-desorption indicate that the products are macropore materials with the pore size of 1-3 {mu}m, and the Brunauer-Emett-Teller (BET) surface area was 14 m{sup 2}/g. As a typical morphology, the possible growth process of HGMC was also investigated and discussed. The experimental results show that the in situ formed MgO microparticles play a template role during the HGMC formation.

36 MATERIALS SCIENCE↗

Variation of char structure during anthracite pyrolysis catalyzed by Fe{sub 2}O{sub 3} and its influence on char combustion reactivity

Effects of Fe{sub 2}O{sub 3} on the pyrolysis reactivity of demineralized anthracite were investigated by a thermo-gravimetric analyzer, indicating that pyrolysis reactivity of Fe{sub 2}O{sub 3}-loaded demineralized anthracite was higher than that of raw demineralized anthracite when temperature is over 500{sup o}C. Chars were prepared from the two coal samples in muffle with heating progress, and their structures were analyzed using SEM, FTIR, XRD, and Raman. FTIR results showed that absorption peaks of functional groups on the surface of char from catalytic pyrolysis at 700{sup o}C were more than that of char from noncatalytic pyrolysis. Raman results demonstrated values of (I{sub D3} + I{sub D4})/IG of chars from catalytic pyrolysis and noncatalytic pyrolysis were 4.76 and 3.86, respectively, indicating that ordering of the char was decreased by Fe{sub 2}O{sub 3}. XRD analysis revealed that diffraction angle of the 002 peak did not shift; however, L{sub a} and L{sub c} decreased, indicating degree of graphitization for microcrystalline structure of char from catalytic pyrolysis was decreased. The results of FTIR, XRD, and Raman of the char showed that catalytic pyrolysis improved the formation of free radicals, while hindered polymerization and forming of basic structure units. Finally, combustion reactivity of the three chars, including char of raw demineralized anthracite (char-A), char of Fe{sub 2}O{sub 3}-loaded demineralized anthracite (char-B), and char of Fe{sub 2}O{sub 3}-loaded demineralized anthracite washed by HCl (char-C), was investigated using TG and indicated that their active order was char-B > char-C > char-A. The results corroborated that Fe{sub 2}O{sub 3} changed structure of anthracite char and improved combustion reactivity.

01 COAL, LIGNITE, AND PEAT↗

Ytterbium Ion Collection on Graphite Plates

Surface characterization and analysis of the graphite collection and strike plates was conducted in this report. These plates were from an electromagnetic isotope separation collector that had been irradiated with an ytterbium ion beam. The results of this study are reported along with analysis and discussion of the potential growth mechanism of the ytterbium layer on graphite. It is proposed that directional deposition of ytterbium ions occurs first in the defect regions of the graphite plate. As deposition continues, it leads to the eventual formation of directional globs that elongate and grow into plates, then stacks, and finally into sheets of ytterbium. The ytterbium layer appears to have a definite phase boundary with the graphite layer. It was also determined that during irradiation with the ytterbium ion beam, the sputtered carbon becomes interpolated in the ytterbium surface layer on the graphite plate and has an amorphous microstructure.

36 MATERIALS SCIENCE↗

Modeling Graphite Behavior (Fracture and Oxidation)

Purpose of this work Oxidation modeling Oxidation of full-scale components Local properties in oxidized components Graphite fracture strength Phase field fracture modeling Microstructurally informed fracture model IG-110 tensile results and comparison to experiment Work in progress and future work

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Understanding the Reaction of Nuclear Graphite with Molecular Oxygen

A thorough understanding of oxidation is important when considering the health and integrity of graphite components in graphite reactors. For the next generation of graphite reactors, HTGRs specifically, an unlikely air ingress has been deemed significant enough to have made its way into the licensing applications of many international licensing bodies. While a substantial body of literature exists on nuclear graphite oxidation in the presence of molecular oxygen and significant efforts have been made to characterize oxidation kinetics of various grades, the value of existing information is somewhat limited. Often, multiple competing processes, including reaction kinetics, mass transfer, and microstructural evolution, are lumped together into a single rate expression that limits the ability to translate this information to different conditions. This article reviews the reaction of graphite with molecular oxygen in terms of the reaction kinetics, gas transport, and microstructural evolution of graphite. It also presents the foundations of a model for the graphite-molecular oxygen reaction system that is kinetically independent of graphite grade, and is capable of describing both the bulk and local oxidation rates under a wide range of conditions applicable to air-ingress.

J. Kane, Joshua↗