Search NASA⌕ Search

SEARCH · Search NASA

Results for “manipulations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

A method for estimating the mass properties of a manipulator by measuring the reaction moments at its base

Emulating on earth the weightlessness of a manipulator floating in space requires knowledge of the manipulator's mass properties. A method for calculating these properties by measuring the reaction forces and moments at the base of the manipulator is described. A manipulator is mounted on a 6-DOF sensor, and the reaction forces and moments at its base are measured for different positions of the links as well as for different orientations of its base. A procedure is developed to calculate from these measurements some combinations of the mass properties. The mass properties identified are not sufficiently complete for computed torque and other dynamic control techniques, but do allow compensation for the gravitational load on the links, and for simulation of weightless conditions on a space emulator. The algorithm has been experimentally demonstrated on a PUMA 260 and used to measure the independent combinations of the 16 mass parameters of the base and three proximal links.

West, Harry↗
NASA NTRS1989

End-point control of a two-link manipulator with a very flexible forearm - Issues and experiments

For mechanical manipulators, a logical sensor location is at the manipulator end-point where tasks are performed. Unfortunately, when bending flexibility exists between an end-point sensor and a joint actuator, stability and performance are achieved only through sophisticated control design. Some of the issues involved in utilizing end-point sensing for two-link flexible manipulators are addressed. A modeling technique that properly represents the foreshortening of a flexible link undergoing deflections is presented. In order to realize fully the advantages of the assumed-modes modeling method, mode shapes are selected that allow a low-order model to be used effectively for simulation and control purposes. A nonlinear controller, incorporating state feedback and a constant-gain extended Kalman filter driven by end-point measurements, is designed and compared to a conventional proportional-plus-derivative controller that uses collocated sensors. Results from implementing these controllers on the experimental Stanford multilink flexible manipulator are given.

Oakley, Celia M.↗
NASA NTRS1988

Base reaction optimization of redundant manipulators for space applications

One of the problems associated with redundant manipulators which were proposed for space applications is that the reactions transmitted to the base of the manipulator as a result of the motion of the manipulator will cause undesirable effects on the dynamic behavior of the supporting space structure. It is therefore necessary to minimize the magnitudes of the forces and moments transmitted to the base. It is shown that kinematic redundancy can be used to solve the dynamic problem of minimizing the magnitude of the base reactions. The methodology described is applied to a four degree-of-freedom spatial manipulator with one redundant degree-of-freedom.

Chung, C. L.↗
NASA NTRS1990

Trajectory planning and control of a 6 DOF manipulator with Stewart platform-based mechanism

The trajectory planning and control was studied of a robot manipulator that has 6 degrees of freedom and was designed based on the mechanism of the Stewart Platform. First the main components of the manipulator is described along with its operation. The solutions are briefly prescribed for the forward and inverse kinematics of the manipulator. After that, two trajectory planning schemes are developed using the manipulator inverse kinematics to track straight lines and circular paths. Finally experiments conducted to study the performance of the developed planning schemes in tracking a straight line and a circle are presented and discussed.

Nguyen, Charles C.↗
NASA NTRS1989

A 17 degree of freedom anthropomorphic manipulator

A 17 axis anthropomorphic manipulator, providing coordinated control of two seven degree of freedom arms mounted on a three degree of freedom torso-waist assembly, is presented. This massively redundant telerobot, designated the Robotics Research K/B-2017 Dexterous Manipulator, employs a modular mechanism design with joint-mounted actuators based on brushless motors and harmonic drive gear reducers. Direct joint torque control at the servo level causes these high-output joint drives to behave like direct-drive actuators, facilitating the implementation of an effective impedance control scheme. The redundant, but conservative motion control system models the manipulator as a spring-loaded linkage with viscous damping and rotary inertia at each joint. This approach allows for real time, sensor-driven control of manipulator pose using a hierarchy of competing rules, or objective functions, to avoid unplanned collisions with objects in the workplace, to produce energy-efficient, graceful motion, to increase leverage, to control effective impedance at the tool or to favor overloaded joints.

Vold, Havard I.↗
NASA NTRS1989

A new approach to global control of redundant manipulators

A new and simple approach to configuration control of redundant manipulators is presented. In this approach, the redundancy is utilized to control the manipulator configuration directly in task space, where the task will be performed. A number of kinematic functions are defined to reflect the desirable configuration that will be achieved for a given end-effector position. The user-defined kinematic functions and the end-effector Cartesian coordinates are combined to form a set of task-related configuration variables as generalized coordinates for the manipulator. An adaptive scheme is then utilized to globally control the configuration variables so as to achieve tracking of some desired reference trajectories. This accomplishes the basic task of desired end-effector motion, while utilizing the redundancy to achieve any additional task through the desired time variation of the kinematic functions. The control law is simple and computationally very fast, and does not require the complex manipulator dynamic model.

Seraji, Homayoun↗
NASA NTRS1989

A complete analytical solution for the inverse instantaneous kinematics of a spherical-revolute-spherical (7R) redundant manipulator

Using a method based upon resolving joint velocities using reciprocal screw quantities, compact analytical expressions are generated for the inverse solution of the joint rates of a seven revolute (spherical-revolute-spherical) manipulator. The method uses a sequential decomposition of screw coordinates to identify reciprocal screw quantities used in the resolution of a particular joint rate solution, and also to identify a Jacobian null-space basis used for the direct solution of optimal joint rates. The results of the screw decomposition are used to study special configurations of the manipulator, generating expressions for the inverse velocity solution for all non-singular configurations of the manipulator, and identifying singular configurations and their characteristics. Two functions are therefore served: a new general method for the solution of the inverse velocity problem is presented; and complete analytical expressions are derived for the resolution of the joint rates of a seven degree of freedom manipulator useful for telerobotic and industrial robotic application.

Podhorodeski, R. P.↗
NASA NTRS1989

Reflexive obstacle avoidance for kinematically-redundant manipulators

Dexterous telerobots incorporating 17 or more degrees of freedom operating under coordinated, sensor-driven computer control will play important roles in future space operations. They will also be used on Earth in assignments like fire fighting, construction and battlefield support. A real time, reflexive obstacle avoidance system, seen as a functional requirement for such massively redundant manipulators, was developed using arm-mounted proximity sensors to control manipulator pose. The project involved a review and analysis of alternative proximity sensor technologies for space applications, the development of a general-purpose algorithm for synthesizing sensor inputs, and the implementation of a prototypical system for demonstration and testing. A 7 degree of freedom Robotics Research K-2107HR manipulator was outfitted with ultrasonic proximity sensors as a testbed, and Robotics Research's standard redundant motion control algorithm was modified such that an object detected by sensor arrays located at the elbow effectively applies a force to the manipulator elbow, normal to the axis. The arm is repelled by objects detected by the sensors, causing the robot to steer around objects in the workspace automatically while continuing to move its tool along the commanded path without interruption. The mathematical approach formulated for synthesizing sensor inputs can be employed for redundant robots of any kinematic configuration.

Karlen, James P.↗
NASA NTRS1989

HERMIES-3: A step toward autonomous mobility, manipulation, and perception

HERMIES-III is an autonomous robot comprised of a seven degree-of-freedom (DOF) manipulator designed for human scale tasks, a laser range finder, a sonar array, an omni-directional wheel-driven chassis, multiple cameras, and a dual computer system containing a 16-node hypercube expandable to 128 nodes. The current experimental program involves performance of human-scale tasks (e.g., valve manipulation, use of tools), integration of a dexterous manipulator and platform motion in geometrically complex environments, and effective use of multiple cooperating robots (HERMIES-IIB and HERMIES-III). The environment in which the robots operate has been designed to include multiple valves, pipes, meters, obstacles on the floor, valves occluded from view, and multiple paths of differing navigation complexity. The ongoing research program supports the development of autonomous capability for HERMIES-IIB and III to perform complex navigation and manipulation under time constraints, while dealing with imprecise sensory information.

Weisbin, C. R.↗
NASA NTRS1989

The control of space manipulators subject to spacecraft attitude control saturation limits

The motions of robotic manipulators mounted on spacecraft can disturb the spacecraft's positions and attitude. These disturbances can surpass the ability of the system's attitude control reaction jets to control them, for the disturbances increase as manipulator speeds increase. If the manipulator moves too quickly the resulting disturbances can exceed the saturation levels of the reaction jets, causing excessive spacecraft motions. A method for planning space manipulator's motions is presented, so that tasks can be performed as quickly as possible without saturating the system's attitude control jets.

Dubowsky, S.↗
NASA NTRS1989

Kinematics and control algorithm development and simulation for a redundant two-arm robotic manipulator system

An efficient approach to cartesian motion and force control of a 7 degree of freedom (DOF) manipulator is presented. It is based on extending the active stiffness controller to the 7 DOF case in general and use of an efficient version of the gradient projection technique for solving the inverse kinematics problem. Cooperative control is achieved through appropriate configuration of individual manipulator controllers. In addition, other aspects of trajectory generation using standard techniques are integrated into the controller. The method is then applied to a specific manipulator of interest (Robotics Research T-710). Simulation of the kinematics, dynamics, and control are provided in the context of several scenarios: one pertaining to a noncontact pick and place operation; one relating to contour following where contact is made between the manipulator and environment; and one pertaining to cooperative control.

Hennessey, Michael P.↗
NASA NTRS1989

A spatial operator algebra for manipulator modeling and control

A recently developed spatial operator algebra, useful for modeling, control, and trajectory design of manipulators is discussed. The elements of this algebra are linear operators whose domain and range spaces consist of forces, moments, velocities, and accelerations. The effect of these operators is equivalent to a spatial recursion along the span of a manipulator. Inversion of operators can be efficiently obtained via techniques of recursive filtering and smoothing. The operator algebra provides a high level framework for describing the dynamic and kinematic behavior of a manipulator and control and trajectory design algorithms. The interpretation of expressions within the algebraic framework leads to enhanced conceptual and physical understanding of manipulator dynamics and kinematics. Furthermore, implementable recursive algorithms can be immediately derived from the abstract operator expressions by inspection. Thus, the transition from an abstract problem formulation and solution to the detailed mechanizaton of specific algorithms is greatly simplified. The analytical formulation of the operator algebra, as well as its implementation in the Ada programming language are discussed.

Rodriguez, G.↗
NASA NTRS1990

Mechanisms leading to net drag reduction in manipulated turbulent boundary layers

Turbulent boundary layers have been manipulated successfully using passive devices called BLADES (boundary-layer alteration devices) leading to net drag reduction. Measurements of various turbulence quantities including intermittency have led to the identification of some of the mechanisms involved in skin-friction reduction. Velocity and vorticity fluctuations associated with oncoming large scales are inhibited significantly by the manipulator blades and the vorticity shed in their wake. The manipulated boundary layers exhibit a reduced intermittency in the outer part of the layer. The effects of manipulation relax with downstream distance and the boundary layer returns toward normal conditions after 100 or 150 boundary-layer thicknesses.

Guezennec, Y. G.↗
NASA NTRS1989

The effects of spatially displaced visual feedback on remote manipulator performance

The effects of spatially displaced visual feedback on the operation of a camera viewed remote manipulation task are analyzed. A remote manipulation task is performed by operators exposed to the following different viewing conditions: direct view of the work site; normal camera view; reversed camera view; inverted/reversed camera view; and inverted camera view. The task completion performance times are statistically analyzed with a repeated measures analysis of variance, and a Newman-Keuls pairwise comparison test is administered to the data. The reversed camera view is ranked third out of four camera viewing conditions, while the normal viewing condition is found significantly slower than the direct viewing condition. It is shown that generalization to remote manipulation applications based upon the results of direct manipulation studies are quite useful, but they should be made cautiously.

Smith, Randy L.↗
NASA NTRS1991

SSSFD manipulator engineering using statistical experiment design techniques

The Satellite Servicer System Flight Demonstration (SSSFD) program is a series of Shuttle flights designed to verify major on-orbit satellite servicing capabilities, such as rendezvous and docking of free flyers, Orbital Replacement Unit (ORU) exchange, and fluid transfer. A major part of this system is the manipulator system that will perform the ORU exchange. The manipulator must possess adequate toolplate dexterity to maneuver a variety of EVA-type tools into position to interface with ORU fasteners, connectors, latches, and handles on the satellite, and to move workpieces and ORUs through 6 degree of freedom (dof) space from the Target Vehicle (TV) to the Support Module (SM) and back. Two cost efficient tools were combined to perform a study of robot manipulator design parameters. These tools are graphical computer simulations and Taguchi Design of Experiment methods. Using a graphics platform, an off-the-shelf robot simulation software package, and an experiment designed with Taguchi's approach, the sensitivities of various manipulator kinematic design parameters to performance characteristics are determined with minimal cost.

Barnes, John↗
NASA NTRS1991

Operations with the special purpose dextrous manipulator on Space Station Freedom

SPAR Canada is actively participating in the Space Station Freedom Program by contributing the Mobile Servicing System (MSS) which will be involved in assembly, maintenance and servicing of both the Space Station and the MSS itself. Part of the MSS is the Special Purpose Dextrous Manipulator (SPDM), a two armed dextrous robot with advanced vision and manipulative capabilities. In addition to Space Station and payload servicing activities the SPDM will be designed to perform self maintenance on the MSS itself. The majority of Space Station equipment will be on orbit for the anticipated 30 year lifespan and the maintenance philosophy will be to repair by the exchange of Orbit Replacement Units or ORUs. The present concept, configuration, and operation of the SPDM and the detailed simulations associated with the maintenance of part of the MSS are described. The Design Reference Mission is the replacement of a Joint Drive Module on the Canadian large payload manipulator, the Space Station Remote Manipulator System. Other Design Reference Missions that were investigated are briefly described, and future operations activity to support the definition of SPDM requirements are discussed.

Cox, B.↗
NASA NTRS1991

Manipulation strategies for massive space payloads

Motion planning and control for the joints of flexible manipulators are discussed. Specific topics covered include control of a flexible braced manipulator, control of a small working robot on a large flexible manipulator to suppress vibrations, control strategies for ensuring cooperation among disparate manipulators, and motion planning for robots in free-fall.

Book, Wayne J.↗
NASA NTRS1990

Stereo advantage for a peg-in-hole task using a force-feedback manipulator

An improved assessment methodology has been implemented at NOSC and tested using an instrumented peg-in-hole (PiH) taskboard. Several aspects of the methodology are discussed in light of their implications for future studies of manipulator performance. Using a simple (but high-fidelity) force-feedback manipulator, a group of 9 trained operators showed a consistent advantage for stereoscopic TV viewing over monoscopic TV viewing when performing the PiH task. To introduce a controlled element of spatial uncertainty into the testing procedure, taskboard orientation relative to the manipulator and remote video camera head was changed in a randomized order on a trial-by-trial basis. The stereoscopic advantage demonstrated by this study can reasonably be expected to be even more pronounced as the quality of the stereo TV interface is improved and force-feedback provided through the manipulator system is diminished and/or distorted.

Spain, Edward H.↗