Search NASA⌕ Search

SEARCH · Search NASA

Results for “zircaloy cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Development and Implementation of Digital Image Correlation for Out-of-Cell Burst Testing

This report details the progress made towards utilizing in-situ methods to observe and quantify unirradiated Zircaloy-4 (Zr4) fuel cladding deformation during out-of-cell design basis accident conditions, specifically during loss-of-coolant accident (LOCA) burst testing in the Severe Accident Test Station at Oak Ridge National Laboratory. Digital image correlation (DIC) was implemented to calculate cladding strain during burst and infrared (IR) thermography was used to attempt a correlation of strain with temperature and to investigate thermal gradients. For both techniques, early experimentation revealed experimental modifications were necessary for implementation. For DIC, this manifested as shortened cladding lengths which could be centered in front of the viewing chamber bored through the IR furnace side, and for IR thermography this meant conducting burst tests in air without a reaction tube and the incorporation of a SiC shell to eliminate direct IR reflections from the tungsten lamps. In the following, the technical issues and subsequent origin of these modifications are discussed, laying the framework for a proof-of-concept DIC/IR characterization of a burst test in the final section.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Ion irradiation effects on Cr-coated zircaloy-4 surface wettability and pool boiling critical heat flux.

The concept of coating the currently used nuclear fuel cladding (zirconium-based alloy, typically Zircaloy-4 or Zirc-4) with an oxidation preventive layer is a progressing Accident tolerant Fuel (ATF) candidate alloys. The coated Zirc-4-based alloys could be a solution to suppress undesirable fast reaction kinetics with high-temperature steam. Zirc-4 has been the most preferred cladding material in pressurized water reactors (PWRs). Chromium (Cr) based alloys as a coating material provides excellent corrosion protection and good strength and wear resistance. In this paper, we present the surface wettability measurements and pool boiling Critical Heat Flux (CHF) for Cr-coated Zirc-4 claddings pre- and post-exposure to an ion irradiation environment. The wettability measurements, including static contact angle (contact angle, θ) and average surface roughness (surface roughness, Ra), are introduced for samples of different coating thicknesses (5–30 μm thick). The coatings fabricated by the cold spray of Cr-Al particles to 10 mm × 10 mm × 1.95 mm Zirc-4 substrates. Post fabrication, a Pilgering (cold rolling) process, was applied to finalize the coating thickness and resulted in a significant reduction in surface roughness of initially fabricated rough surfaces. The process produced three distinguished samples 5-μm unpolished (as machined), 5-μm, and 30-μm polished (cold rolled). The measurements are presented for the three surfaces and bare Zirc-4 as a baseline surface. The contact angle analyses were implemented in theoretical models from the literature to predict pool boiling CHF. Pool boiling experiments were conducted to measure the pool boiling CHF values and compare them to the predicted values. Scanning Electron Microscope (SEM) images and Energy Dispersive X-ray Spectroscopy (EDS) analysis was performed to characterize the surfaces for better understanding and interpreting the results. The SEM images showed localized surface damage due to ion irradiation. No recognized change in the measured surface roughness due to ion irradiation. The contact angles of irradiated Cr-coated surfaces are consistently higher (10°) than pre-irradiated surfaces. Decreasing the Cr-coating layer thickness resulted in lower contact angle pre- and post- ion irradiation. The predicted pool boiling CHF using the Kandlikar model is in good agreement with the experimentally measured CHF values within ±12% for all samples.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Radiation response of FeCrAl-coated Zircaloy-4

Coating the surface of Zircaloy-4 light water reactor fuel cladding tube is of considerable interest for enhancing its accident tolerance. In this study, thermal annealing of FeCrAl-coated Zircaloy-4 at 725 °C for 500 h, was used to induce interfacial reactions between Zircaloy-4 and FeCrAl. The interface zones were then irradiated by 3.5 MeV Zr ions at 400 °C, up to 50, 100, 150 peak dpa values. Transmission electron microscopy (TEM) and scanning TEM were used to characterize microstructural and composition changes before and after ion irradiation. Three interfacial phases were identified: FeZr 3 , (Fe,Cr) 2 Zr, and ZrC. The widest intermetallic layer, FeZr3, had large grains. The narrower phases, (Fe,Cr)2Zr and ZrC, contained small grains and were often mixed. The unexpected observation of the ZrC phase was attributed to the presence of very small impurity level concentrations of carbon in the powder material. No void swelling was observed in any of the phases, including the FeCrAl coating and Zircaloy-4 substrate. (Fe,Cr) 2 Zr, however, fully amorphized after irradiation, even at the lowest dpa.

36 MATERIALS SCIENCE↗
DOE OSTI2023

AFC FY 2023 HFIR Irradiation Test Matrix – Supported by the Design of a Ring Specimen Irradiation Vehicle

The development and deployment of accident-tolerant cladding materials in light water nuclear reactors requires the collection of neutron-irradiated properties of these materials with specific consideration to the material properties orientation (i.e., tube geometry). To that end, a test plan to irradiate several cladding tube and ring specimens in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL) was proposed, along with the development of a new capsule design that features ring specimens with a preexisting gauge section. This ring specimen geometry removes the need to machine a gauge section on the irradiated specimen and thus allows for direct application of a ring-pull test post-irradiation. The test matrix includes uncoated and chromium-coated Zircaloy-4 and advanced zirconium alloy cladding specimens, pre-characterized at ORNL. Plans are to irradiate the specimens at about 4 and 10 dpa—corresponding to two and five cycles at the HFIR centerline—with a target specimen gauge section temperature of 330°C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Effects of Cr/Zircaloy-4 coating qualities for enhanced accident tolerant fuel cladding

Cr-coated zirconium alloys represent a modern approach to enhance cladding safety during accident scenarios. Two high-power impulse magnetron sputtered Cr-coated Zry-4 systems were subjected to simulated loss-of-coolant accident conditions to investigate cladding performance. The first Cr-coating (4.8 µm thick) was deposited onto Zry-4 cladding and exhibited through-thickness cracking while the second Cr-coating (6.8 µm thick) was deposited with improved deposition parameters onto polished Zry-4 and exhibited no cracking. During burst testing, the coating with a higher density of defects failed to consistently reduce oxidation and exhibited similar burst behavior as Zry-4. In contrast, the second Cr-coating reduced ZrO 2 formation through formation of Cr 2 O 3 and displayed enhanced burst temperatures by ~80 °C compared to Zry-4. Utilizing an empirical relation for burst behavior of zirconium alloys, the 6.8 µm Cr/Zry-4 system displayed enhanced burst temperatures equivalent to an effective 0.464 mm increase in Zry-4 wall thickness, highlighting the value of continuous Cr coatings for accident scenarios.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

A microstructure-based modeling approach to predict the mechanical properties of Zr alloy with hydride precipitates

In nuclear reactors, hydrides can form in fuel cladding due to hydrogen absorption in ZIrcaloy and cause embrittlement. This work presents a microstructure-based finite element model to predict the stress-strain response of Zircaloy containing hydrides. Quantitative microstructural details extracted from scanning electron microscopy (SEM) images were used to generate heterogeneous microstructures including the morphology and spatial distribution of hydrides. The constitutive material model for zircaloy in this study is based on crystal plasticity theory which considers the hexagonal close-packed (HCP) atomic structure of Zircaloy material. The hydrides were modeled as brittle material along with a damage model. Hydride formation inside the zircoloy matrix results in residual stress. This phenomenon is also captured in this model. A parametric study has been conducted to understand the effect of volume fraction, orientation, and lamellae thickness of the hydride phase on the mechanical properties of the overall material.

Kulkarni, Shank S.↗
DOE OSTI2020

In Situ High-Temperature Synchrotron Diffraction Studies of (Fe,Cr,Al) 3 O 4 Spinels

The modeling of a loss-of-coolant-accident scenario involving nuclear fuels with FeCrAl cladding materials in consideration to replace a Zircaloy requires knowledge of the thermodynamics of oxidized structures. At temperatures higher than 1500 degrees C, oxidation of FeCrAl alloys forms (Fe,Cr,Al) 3 O 4 spinels. In situ high-energy X-ray diffraction in a conical nozzle levitator installed at beamline 6-ID-D of the APS was used to study the structural evolution of the oxides as a function of the temperature. Single-phase (spinel) and multiphase (spinel-corundum-FeAlO 3 ) regions are mapped as a function of the temperature for three different compositions of FeCrAl oxidation products. The thermal expansion coefficients and cation distribution in the spinel structure have been refined. The temperature at which complete melting of the fuel cladding is expected has been determined by the liquidus temperatures of the oxidized products to be between 1657 and 1834 degrees C in a 20% O 2 /Ar atmosphere using the cooling trace method. The liquidus temperature increases with increasing Al and Cr content in the spinel phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Measuring thermal diffusivity and gap conductance in uranium nitride and Zircaloy relevant for microreactor applications

Heat transfer across nuclear fuels and structural interfaces is an important factor for evaluating the performance of nuclear power systems. Specifically, heat generated as nuclear fuel fissions must be transported through the cladding material and through the reactor to reach the steam turbine for power generation. As new microreactor designs emerge, maximizing the efficiency of this heat transfer process becomes crucial to make them commercially viable. This article examines thermal diffusivity and gap conductance in uranium nitride (UN) fuel and Zircaloy-4 (Zry4) cladding using light flash analysis (LFA). Thermal diffusivity measurements were made on monolithic UN pellets and Zry4 exposed to carbon at peak operating temperatures of microreactors and show that carbon ingress has a minimal effect on thermal diffusivity when compared with identical materials not exposed to carbon. Evaluation of gap conductance at the UN-Zry4 interface was done using one-dimensional two-layer thermal transport models as a function of applied pressure. Here the results show that increasing pressure on the UN-Zry4 interface leads to gains in gap conductance per unit area in fuel-cladding assemblies at microreactor operating temperatures. While many other variables are expected to influence UN-Zry4 interfacial gap conductance (e.g. contact surface roughness, porosity, localized heating, environmental gas pressure), the work offers a demonstration of using a conventional LFA apparatus to determine this parameter at elevated temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

High spatial resolution thermal conductivity mapping of SiC/SiC composites

Herein, silicon carbide (SiC) ceramic matrix composites are being investigated as a new generation of fuel cladding materials due to its higher accident tolerance compared to Zircaloy. Characterization of the thermal conductivity of SiC constituents and their interfaces and interphases in SiC/SiC composites is needed as inputs to models of cladding performance. We used time-domain thermoreflectance (TDTR) to map the thermal conductivity with a spatial resolution of 2 µm. The SiC/SiC composite is comprised of Hi-Nicalon Type S fibers in a matrix made by chemical vapor infiltration (CVI matrix). The interphase material is a pyrolytic carbon/SiC multilayer. We report thermal conductivity maps of the SiC fiber and SiC matrix at temperatures of 25 °C, 90 °C, 164 °C, and 250 °C. The fiber has a uniform and isotropic thermal conductivity of 22 W m -1 K -1 at 25 °C; the thermal conductivity of fiber is approximately independent of temperature. The matrix thermal conductivity is not uniform and varies from 50 to 120 W m -1 K -1 at 25 °C; the thermal conductivity of the matrix scales approximately with the inverse of the square root of temperature, i.e., ∝ 1/T 1/2 . The thermal conductivity of the interphase at room temperature is 6 W m -1 K -1 . The calculated spatially averaged thermal conductivity of this SiC/SiC composite at 1000°C is 29 W m -1 K -1 .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Fundamental Studies of Tritium Formation and Diffusivity in Pure and Defective Zircaloy-4 Getters

Zirconium (Zr) and its alloys are used as fuel cladding in nuclear reactors. These materials have their low absorption cross-section for thermal neutrons and have good mechanical and thermal properties. In addition, they are used as tritium getters in tritium-producing burnable absorber rods (TPBARs), in the form of nickel-plated Zircaloy-4 tubes. To produce 3 H, the breading blankets such as lithium aluminate are irradiated in pressurized water. 3 H produced in this process is captured by the getter and 3 H reacts chemically with Zr to form metal hydride (ZrTx). The precipitation of metal hydride results in not only the volume increase and hydrogen embrittlement of zircaloy but also changes in getter’s chemical properties. This degrades the getter’s performance. Therefore, understanding the behavior of 3 H (such as diffusion and solubility) in zircaloy is important to understand getter performance.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Effect of PVD-coated chromium on the subcooled flow boiling performance of nuclear reactor cladding materials

Here we elucidate the separate effect of a thin Cr coating deposited by physical vapor deposition (PVD) on the subcooled flow boiling performance of zircaloy-4. First, we run flow boiling experiments on prototypical zircaloy-4 surfaces mimicking the scratch pattern and surface roughness of nuclear reactor claddings. Then, we PVD-coat a 0.3 µm thick chromium layer on the same exact surface and repeat the same flow boiling investigations. All experiments are run using deionized water at atmospheric pressure, flowing on a 1 × 3 cm 2 rectangular cross section channel at a rate of 1000 kg/m 2 /s and a subcooling of 10 K. We measure the average temperature of the boiling surface at increasing surface heat fluxes, covering a wide range of heat transfer regimes, from single-phase forced convection to the boiling crisis. We also record high-speed videos of the boiling process, which we postprocess to measure bubble nucleation site density, growth time, departure diameter and frequency. The surface analysis reveals that, while the chromium coating does not seem change the surface roughness and morphology, it improves surface wettability. However, it decreases the critical heat flux. The chromium coating causes an increase of nucleation temperature, bubble departure diameter and growth time, and a reduction of the nucleation site density. The concurrence of these observations indicates that a size reduction of the nucleation sites, conformally covered by the chromium coating, may be the cause of the boiling performance deterioration. We confirm this hypothesis repeating the same analysis on a FeCrAl sample prepared and tested using the same protocol as the zircaloy-4 sample, but with a different initial surface texture.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

High temperature creep model development using in-situ 3-D DIC techniques during a simulated LOCA transient

In-situ strain measurements of fuel cladding can enable high-throughput data collection and validation to support accelerated qualification of cladding materials. Here, in this work, 3D digital image correlation was used to map strain for both Zircaloy-4 (Zry-4) and Cr-coated Zry-4 during two types of cladding rupture experiments: isobaric temperature ramp tests at 5 °C/s and isothermal pressure jump tests at 600 °C. Zry-4 strain data initially showed a temperature dependence expected for creep deformation, yet a shift to a new plastic deformation mechanism not reported in literature dominated during the finals seconds prior to rupture. Cr-coated Zry-4 did not show the change in deformation mechanism at the end of life and showed a delay in measurable creep deformation. Stress dependences were similar for Zry-4 and Cr/Zry-4 during pressure jump tests. Cr-coatings were found to decrease the strain rate during both testing scenarios. Creep parameters were calculated to support modelling efforts regarding design basis accidents.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Structure evolution and tin redistribution during oxidation of Zircaloy-4 at 500°C

Zirconium (Zr) alloys are widely used as fuel cladding in nuclear power reactors due to their thermal stability, mechanical durability, corrosion resistance, and low neutron absorption cross-section. However, their performance is challenged by oxidation in reactor environments, making the study of Zr alloy corrosion behavior crucial for ensuring the safety, longevity, and economic viability of nuclear power systems. While the oxidation behavior of Zr-based cladding materials has been extensively studied since the 1950s, a mechanistic understanding into the relationship between structure evolution, solute element redistribution, and properties remains elusive. Valuable insights may be obtained through advanced experimental methods, such as in-situ and high resolution microscopy techniques. Here, in this study, the oxidation behavior of Zircaloy-4 at 500 °C in O 2 is characterized using a multimodal advanced characterization approach. Using in-situ X-ray diffraction, the phase evolution from metastable to stable oxides is tracked in real time. Complementary high-resolution techniques, including electron microscopy and atom probe tomography, reveal nanoscale insights into the microstructural changes and solute redistribution across the oxide/metal interface. Nanohardness mapping across the oxide/metal interface highlights localized mechanical property variations that may be linked to changes in microstructure and crystal structure within the oxide layer. These findings offer valuable insights into the microstructure and property evolution of Zircaloy-4 during oxidation, contributing to a better understanding of microstructural changes in Zr-based alloys under oxidative environments.

APT↗
DOE OSTI2023

Determination of the hydrogen heat of transport in Zircaloy-4

During operation in a nuclear reactor, Zr-based nuclear fuel cladding is subject to waterside corrosion which can lead to hydrogen ingress. Here, the hydrogen that enters the material will migrate to colder spots and precipitate as zirconium hydrides if the hydrogen content exceeds the hydrogen terminal solid solubility in the material. Since a temperature gradient is established in the radial direction of the cladding during operation, the hydrides can preferentially precipitate at the colder outer surface of the cladding. Other gradients can also occur in the longitudinal and azimuthal directions of the cladding tube. As a consequence, hydrogen redistributes itself in response to the concentration and temperature gradients present in the sample. The response of the hydrogen in solid solution to temperature gradients is governed by the heat of transport Q* as a function of temperature, so it can be used in the BISON code. A set of experiments was set up to determine the heat of transport (Q*), in which a uniformly hydrided Zircaloy-4 sample is annealed under a fixed temperature gradient at a range of temperatures, and the resulting hydrogen distribution is analyzed to determine Q*. The results are discussed in terms of existing literature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Hydrogen and Deuterium Reactivity with Carbon Surface Impurities on the TPBAR Getter Ni Plate Studied in situ with Environmental XPS

Tritium for the U.S. Department of Energy’s Tritium Readiness Program is produced in tritium-producing burnable absorber rods (TPBARs) inserted into light-water nuclear reactors. The rods are stainless-steel-clad tubes with a permeation barrier coating and internal components. The internal components have been designed and selected to produce and retain tritium. The TPBAR incorporates a Ni-plated Zircaloy-4 getter tube to capture tritium and prevent it from reaching the rod cladding and permeating into the environment. The role of the Ni coating is to protect the Zircaloy-4 getter from oxidation while allowing for maximum tritium permeability. Ubiquitous surface impurities on the Ni, such as carbon, could limit its protective functionality and permeability if they exist in relatively large concentrations. The reactivity of impurity carbon with permeating tritium can also result in tritiated hydrocarbon impurities on the gas phase. The goal of this work is to determine quantitatively the chemical state and reactivity of potential Ni coating impurities in actual TPBAR getter samples. Using Environmental X-ray Photoelectron Spectroscopy (eXPS), a very sensitive gas/surface chemistry diagnostic, we reveal in situ the source and evolution of carbon on the Ni surface at different hydrogen and deuterium pressure conditions, and how carbon reactivity may result in hydrocarbon gas-evolution at application-relevant temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Irradiation creep measurement and microstructural analysis of chromium nitride–coated zirconium alloy using pressurized tubes

Environmental barrier coatings for Zr-based materials are currently under development to reduce oxidation and embrittlement in light-water reactors. Chromium nitride is one such candidate for this application, particularly as accident-tolerant fuel cladding. However, quantifying the impact of coatings on the irradiation-induced creep of zircaloy (Zry) is critical as this mechanism often exceeds thermal creep rates under light-water reactor operating conditions and can be a limiting design characteristic. Additionally, examining irradiation effects in the microstructure at the coating interface is key to understanding the compatibility of the material system. Here, to accelerate the experimental measurement of irradiation creep and microstructure evolution in CrN-Zry, compact, pressurized creep tubes were fabricated and irradiated in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory. Miniature, thin-walled rodlets fabricated from annealed Zr-Sn barstock were coated with CrN using physical vapor deposition (PVD) to nominal thicknesses of 4 and 8 μm. Coated and uncoated rodlet specimens were internally pressurized and welded, generating nominal circumferential hoop stresses of 0, 90, or 180 MPa under 300°C irradiation conditions. Twelve specimens were measured diametrically prior to irradiation using a low-cost, automated, contactless laser profilometer developed for this work. Specimens were irradiated in sealed capsules for one 25-day HFIR cycle, accumulating approximately 1.8 $\times$ 10 21 n/cm 2 fast fluence (E n > 10 MeV). The irradiated samples were retrieved and remeasured using the same profilometry system in a shielded hot cell facility. Irradiation creep between specimens was compared using standard statistical tests and showed that both thicknesses of CrN coating had a negligible effect on the irradiation creep strain of the Zry material. Microstructure characterization of pre- and post-irradiated CrN-Zry specimens showed minimal changes due to irradiation but did show a substantial O-rich region at the Zry-CrN interface.

36 MATERIALS SCIENCE↗
DOE OSTI2025

First-Principles Studies of Tritium Species Diffusivity Across the Interfaces of Ni-NiZr Alloy-Zircaloy-4

A tritium producing assembly, also known as tritium producing burnable absorber rods (TPBARs), consists of a metal getter tube located between the cladding and γ-LiAlO2 pellets. The metal getter tube is composed of a nickel (Ni) layer coated on Zircaloy-4. The getter assembly is used to capture tritium (3H) species (mainly 3H2 and 3H2O) generated from γ-LiAlO2 pellets during irradiation. Exploring 3H species (3H2, 3H2O) dissociation on the Ni surface and diffusion in the Ni layer and across the interface of Ni-plated Zircaloy-4 getters can provide insights on tritium transport and retention in the pellets and the getter materials. . In FY25, based on the ideal interface model of Ni-Zircaloy-4 generated in FY24, we will further explore the diffusion pathways of 3H across such Ni-ZrNi-alloy layer-Zircalory-4 interfaces under different conditions, including with oxide/hydroxide clusters on the Ni layer, and impurities located in ZrNi-alloy and Zircalory-4 layers. Due to the size limitation of DFT simulation, we will separate the 3-layer system into 3 sub-systems: Ni-ZrNi interface, ZrNi alloy layer, ZrNi-alloy-Zircaloy-4 interface, and simulate the diffusion barriers for tritium.

diffusion barrier↗
DOE OSTI2024

Complete development of LAROMance-type surrogate models for Zircaloy, as well as initial integration and testing in MOOSE, which addresses industry needs for licensing advanced LWR fuels

This milestone report details the progress in the constitutive surrogate modeling framework for Zircaloy’s mechanical behavior under extreme conditions, within the NEAMS program throughout the U.S. fiscal year 2024 (FY24). The presented work expands on the spectral based mechanical solver and the mechanistic material model for Zircaloy, which were introduced in the NEAMS program during FY22 and detailed in the previous fiscal year (FY23). As part of the NEAMS program, the current effort described in this report focused on the development of a novel viscplastic (creep) surrogate for the mechanistic, polycrystal-based model. To this end, the work was subdivided into two interdependent components related to the necessary improvements to the LApx constitutive model and algorithm and, to the development and use of a surrogate model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗