Search NASA⌕ Search

SEARCH · Search NASA

Results for “Failures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Maximum likelihood estimation for life distributions with competing failure modes

The general model for the competing failure modes assuming that location parameters for each mode are expressible as linear functions of the stress variables and the failure modes act independently is presented. The general form of the likelihood function and the likelihood equations are derived for the extreme value distributions, and solving these equations using nonlinear least squares techniques provides an estimate of the asymptotic covariance matrix of the estimators. Monte-Carlo results indicate that, under appropriate conditions, the location parameters are nearly unbiased, the scale parameter is slightly biased, and the asymptotic covariances are rapidly approached.

Sidik, S. M.↗

Probability of failure prediction for step-stress fatigue under sine or random stress

A previously proposed cumulative fatigue damage law is extended to predict the probability of failure or fatigue life for structural materials with S-N fatigue curves represented as a scatterband of failure points. The proposed law applies to structures subjected to sinusoidal or random stresses and includes the effect of initial crack (i.e., flaw) sizes. The corrected cycle ratio damage function is shown to have physical significance.

Lambert, R. G.↗

Comparison of single crack propagation in lunar analogue glass and the failure strength of rocks

New data of crack propagation in lunar analogue glass provides important input for the construction of deformation maps (maps which delineate the rates and principal means of material deformation under various environmental conditions) applicable to the lunar crust. Comparison of single crack propagation data obtained on flat plates of glass and failure strength data obtained on fine grained rock samples show that single crack propagation velocities are directly related to the failure strength of rocks. The chemical reaction between water and silicon-oxygen bonds at the crack tip seems to be of first order. This greatly simplifies extrapolation to low partial pressures of H2O

Soga, N.↗

Sensor/actuator failure detection for turbofan engines

A procedure for sensor/actuator failure detection using a generalized likelihood ratio (GLR) test is described. The GLR concept can provide a reliable evaluation of failure occurence when associated with a feedback control design which does not require sensor outputs to provide data estimates. A GLR detector was developed and tested.

Behbehani, K.↗

Failure detection and isolation analysis of a redundant strapdown inertial measurement unit

The objective of this study was to define and develop techniques for failure detection and isolation (FDI) algorithms for a dual fail/operational redundant strapdown inertial navigation system are defined and developed. The FDI techniques chosen include provisions for hard and soft failure detection in the context of flight control and navigation. Analyses were done to determine error detection and switching levels for the inertial navigation system, which is intended for a conventional takeoff or landing (CTOL) operating environment. In addition, investigations of false alarms and missed alarms were included for the FDI techniques developed, along with the analyses of filters to be used in conjunction with FDI processing. Two specific FDI algorithms were compared: the generalized likelihood test and the edge vector test. A deterministic digital computer simulation was used to compare and evaluate the algorithms and FDI systems.

Motyka, P.↗

Apparatus for sensor failure detection and correction in a gas turbine engine control system

A gas turbine engine control system maintains a selected level of engine performance despite the failure or abnormal operation of one or more engine parameter sensors. The control system employs a continuously updated engine model which simulates engine performance and generates signals representing real time estimates of the engine parameter sensor signals. The estimate signals are transmitted to a control computational unit which utilizes them in lieu of the actual engine parameter sensor signals to control the operation of the engine. The estimate signals are also compared with the corresponding actual engine parameter sensor signals and the resulting difference signals are utilized to update the engine model. If a particular difference signal exceeds specific tolerance limits, the difference signal is inhibited from updating the model and a sensor failure indication is provided to the engine operator.

Spang, H. A., III↗

Battery failure model derived from flaw theory

A previously derived failure model for battery lifetime is discussed in terms of growth rate of the flaw, distribution of flaw sizes, and number of flaws. Equations are presented for determining the failure model for a nickel cadmium battery.

Schulman, I.↗

Failure analysis methods for capacitors

The basic steps in the failure analysis of discrete capacitors used in electronic circuit boards and hybrid assemblies are described. These steps include: visual examination; functional test; disassembly; isolation of the failure site; and documentation.

Hildenbrand, R. L.↗

Logic analysis of complex systems by characterizing failure phenomena to achieve diagnosis and fault-isolation

A recent result shows that, for a certain class of systems, the interdependency among the elements of such a system together with the elements constitutes a mathematical structure a partially ordered set. It is called a loop free logic model of the system. On the basis of an intrinsic property of the mathematical structure, a characterization of system component failure in terms of maximal subsets of bad test signals of the system was obtained. Also, as a consequence, information concerning the total number of failure components in the system was deduced. Detailed examples are given to show how to restructure real systems containing loops into loop free models for which the result is applicable.

Wong, J. T.↗

Incipient failure detection (IFD) of SSME ball bearings

Because of the immense noise background during the operation of a large engine such as the SSME, the relatively low level unique ball bearing signatures were often buried by the overall machine signal. As a result, the most commonly used bearing failure detection technique, pattern recognition using power spectral density (PSD) constructed from the extracted bearing signals, is rendered useless. Data enhancement techniques were carried out by using a HP5451C Fourier Analyzer. The signal was preprocessed by a Digital Audio Crop. DAC-1024I noise cancelling filter in order to estimate the desired signal corrupted by the backgound noise. Reference levels of good bearings were established. Any deviation of bearing signals from these reference levels indicate the incipient bearing failures.

Source record↗

Detection, Diagnosis and Prognosis: Contribution to the energy challenge: Proceedings of the Meeting of the Mechanical Failures Prevention Group

The contribution of failure detection, diagnosis and prognosis to the energy challenge is discussed. Areas of special emphasis included energy management, techniques for failure detection in energy related systems, improved prognostic techniques for energy related systems and opportunities for detection, diagnosis and prognosis in the energy field.

Shives, T. R.↗

Deformation and failure mechanisms of graphite/epoxy composites under static loading

The mechanisms of deformation and failure of graphite epoxy composites under static loading were clarified. The influence of moisture and temperature upon these mechanisms were also investigated. Because the longitudinal tensile properties are the most critical to the performance of the composite, these properties were investigated in detail. Both ultimate and elastic mechanical properties were investigated, but the study of mechanisms emphasized those leading to failure of the composite. The graphite epoxy composite selected for study was the system being used in several NASA sponsored flight test programs.

Clements, L. L.↗

Analysis of the shearout failure mode in composite bolted joints

A semi-empirical shearout strength model has been formulated for the analysis of composite bolted joints with allowance for the effects of joint geometry. The model employs a polynomial stress function in conjunction with a point stress failure criterion to predict strength as a function of fastener size, edge distance, and half spacing. The stress function is obtained by two-dimensional plane-stress finite element analysis using quadrilateral elements with orthotropic material properties. Comparison of experimentally determined shearout strength data with model predicted failures has substantiated the accuracy of the model.

Wilson, D. W.↗

Issues in the development of a general design algorithm for reliable failure detection

The design of residual-generation processes is briefly discussed, the goal being to develop a methodology for designing robust processes of this type. It is noted that analytical redundancy forms the basis for residual-generation, representing the relationships between the outputs of sensors and inputs of actuators via the dynamics of the system. It is because of this relationship that sensor outputs (even those of dissimilar sensors and at different times) can, in effect, be compared to ascertain whether they are consistent with normal system behavior. The residuals can be seen as constituting the discrepancy between the output resulting from such comparisons; they should display noise-like characteristics only in the normal mode. Failures in the system would lead to a discrepancy between the observed and expected behavior of the sensor outputs and hence to abnormal characteristics (failure signatures) in the residual.

Chow, E. Y.↗

Fracture and failure: Analyses, mechanisms and applications; Proceedings of the Symposium, Los Angeles, CA, March 17-20, 1980

Papers are presented on the application of fracture mechanics to spacecraft design, fracture control applications on the Space Shuttle reaction control thrusters, and an assessment of fatigue crack growth rate relationships for metallic airframe materials. Also considered are fracture mechanisms and microstructural relationships in Ni-base alloy systems, the use of surface deformation markings to determine crack propagation directions, case histories of metallurgical failures in the electronics industry, and a failure analysis of silica phenolic nozzle liners.

Tung, P. P.↗

The effects of inherent flaws on the time and rate dependent failure of adhesively bonded joints

Inherent flaws, as well as the effects of rate and time, are shown by tests on viscoelastic adhesive-bonded single lap joints to be as critical in joint failure as environmental and stress concentration effects, with random inherent flaws and loading rate changes resulting in an up to 40% reduction in joint strength. It is also found that the asymptotic creep stress, below which no delayed failure may occur, may under creep loading be as much as 45% less than maximum adhesive strength. Attention is given to test results for the case of titanium-LARC-3 adhesive single-lap specimens.

Sancaktar, E.↗

Photovoltaic module reliability improvement through application testing and failure analysis

During the first four years of the U.S. Department of Energy (DOE) National Photovoltatic Program, the Jet Propulsion Laboratory Low-Cost Solar Array (LSA) Project purchased about 400 kW of photovoltaic modules for test and experiments. In order to identify, report, and analyze test and operational problems with the Block Procurement modules, a problem/failure reporting and analysis system was implemented by the LSA Project with the main purpose of providing manufacturers with feedback from test and field experience needed for the improvement of product performance and reliability. A description of the more significant types of failures is presented, taking into account interconnects, cracked cells, dielectric breakdown, delamination, and corrosion. Current design practices and reliability evaluations are also discussed. The conducted evaluation indicates that current module designs incorporate damage-resistant and fault-tolerant features which address field failure mechanisms observed to date.

Dumas, L. N.↗

Buckling and failure characteristics of graphite-polyimide shear panels

The buckling and failure characteristics of unstiffened, blade stiffened, and hat stiffened graphite-polyimide shear panels are described. The picture frame shear test is used to obtain shear stress-strain data at room temperature and at 316 deg C. The experimental results are compared with a linear buckling analysis, and the specimen failure modes are described. The effect of the 316 deg C test temperature on panel behavior are discussed.

Shuart, M. J.↗