Search NASA⌕ Search

SEARCH · Search NASA

Results for “Material Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Selective Capture of Cesium and Thallium from Natural Waters and Simulated Wastes with Copper Ferrocyanide Functionalized Mesoporous Silica

Copper(II) ferrocyanide immobilized inside mesoporous silica MCM-41 supports (Cu-FC-EDA-SAMMSTM) has been evaluated against iron(III) hexacyanoferrate(II) (insoluble Prussian blue) for the sorption of cesium (Cs+) and thallium (Tl+) from natural waters and simulated wastes. The affinities (in term of distribution coefficients, Kd) of both sorbents for Cs and Tl were measured as a function of solution pH, competing cations, and matrices. For the entire pH studied (pH 0.1 to 7.3), Cu-FC-EDA-SAMMS had higher affinities for Cs and Tl (one to two orders of magnitude higher Kd) than Prussian blue and was less negatively impacted by the solution pH, competing cations, and matrices. The adsorption isotherms and kinetics of the two sorbents for Cs and/or Tl were also determined in seawater and simulated acid and alkaline wastes. SAMMS outperformed Prussian blue in terms of maximum adsorption capacity (e.g., 21.7 versus 2.6 mg Cs/g in acid waste stimulant, pH 1.1), and rate (e.g., over 95 wt% of Cs was removed after 2 minutes with SAMMS, while only 75 wt% was removed with Prussian blue). The lower affinity, capacity, and rate of Cs and Tl sorption on Prussian blue than those on Cu-FC-EDA-SAMMS were attributed to the molecular pore sizes, which restrict mass transport, and the insoluble Cs abducts of the Prussian blue, which restrict the ability of neighboring binding sites to further bind Cs ions. On the other hand, the large pores of SAMMS not only enable faster diffusion and faster binding chemistry, but they also allow isolation of binding sites so that one Cs binding event does not impact further Cs binding. In addition, iron (Fe) dissolved from insoluble Prussian blue over 10-fold of that from Cu-FC-EDA-SAMMS after 24 hours of contact time, indicating poorer material stability of Prussian blue.

54 ENVIRONMENTAL SCIENCES↗

Effect of entropy of lithium intercalation in cathodes and anodes on Li-ion battery thermal management

The entropy changes (ΔS) in various cathode and anode materials, as well as complete Li-ion batteries, were measured using an electrochemical thermodynamic measurement system (ETMS). LiCoO 2 has a much larger entropy change than electrodes based on LiNi x Co y Mn z O 2 and LiFePO 4 , while lithium titanate based anode has lower entropy change compared to graphite anodes. Reversible heat generation rate was found to be a significant portion of the total heat generation rate. The appropriate combinations of cathode and anode were investigated to minimize reversible heat.

25 ENERGY STORAGE↗

X-ray microtomography

In this tutorial, we describe X-ray microtomography as a technique to nondestructively characterize material microstructure in three dimensions at a micron level spatial resolution. While commercially available laboratory scale instrumentation is available, we focus our attention on synchrotron-based systems, where we can exploit a high flux, monochromatic X-ray beam to produce high fidelity three-dimensional images. A brief description of the physics and the mathematical analysis behind the technique is followed by example applications to specific materials characterization problems, with a particular focus on the utilization of three-dimensional image processing that can be used to extract a wide range of useful information.

36 MATERIALS SCIENCE↗

Beam characterization at the Neutron Radiography Reactor

The quality of a neutron-imaging beam directly impacts the quality of radiographic images produced using that beam. Fully characterizing a neutron beam, including determination of the beam's effective length-to-diameter ratio, neutron flux profile, energy spectrum, potential image quality, and beam divergence, is vital for producing quality radiographic images. This paper provides a characterization of the east neutron imaging beamline at the Idaho National Laboratory Neutron Radiography Reactor (NRAD). The experiments which measured the beam's effective length-to-diameter ratio and potential image quality are based on American Society for Testing and Materials (ASTM) standards. An analysis of the image produced by a calibrated phantom measured the beam divergence. The energy spectrum measurements consist of a series of foil irradiations using a selection of activation foils, compared to the results produced by a Monte Carlo n-Particle (MCNP) model of the beamline. The NRAD has an effective collimation ratio greater than 125, a beam divergence of 0.3 +_ 0.1 degrees, and a gold foil cadmium ratio of 2.7. The flux profile has been quantified and the facility is an ASTM Category 1 radiographic facility. Based on bare and cadmium covered foil activation results, the neutron energy spectrum used in the current MCNP model of the radiography beamline over-samples the thermal region of the neutron energy spectrum.

99 GENERAL AND MISCELLANEOUS↗

Power performance and loads characterization of laboratory-scale cross-flow rotors fabricated using additive manufacturing

Tidal energy conversion is a relatively new application for additive manufacturing (AM), where the focus has been on fabricating axial-flow turbine blades. AM techniques add material precisely where it is needed, creating more complex shapes with less waste. Cross-flow rotor geometry presents an opportunity for AM to improve rotor performance by fabricating features that cannot be created economically via conventional manufacturing. The challenges associated with using AM in cross-flow design include water resistance and degradation over time while retaining a level of quality equivalent to conventionally machined parts. In this work, AM materials were tested by environmentally conditioning samples in a seawater tank for 5 months, followed by performance and phase-resolved load testing of laboratory-scale rotors in a hydraulic flume. We found that while metals like titanium and Inconel have excellent performance in marine environments, achieving the desired geometry and performance is difficult. Thermoplastics degraded in seawater but were easier to form into desired geometries and could exceed the performance of an aluminum control rotor. Warping and surface finish were significant detractors from AM rotor performance. These results suggest that the primary benefits of using AM for cross-flow rotors is to quickly fabricate and test unconventional rotor geometries.

16 TIDAL AND WAVE POWER↗

Hydrothermal treatment of MSWI bottom ash forming acid-resistant material

To recycle municipal solid waste incinerator (MSWI) bottom ash, synthesis of hydrothermal minerals from bottom ash was performed to stabilize heavy metals. MSWI bottom ash was mixed with SiO{sub 2}, Al(OH){sub 3}, and Mg(OH){sub 2} so its chemical composition was similar to that of hydrothermal clay minerals. These solid specimens were mixed with water at a liquid/solid ratio of 5. The reaction temperature was 200 deg. C, and reactions were performed for 24-240 h. Generation of kaolinite/smectite mixed-layer clay mineral was found in the samples after the reaction of the mixture of bottom ash, SiO{sub 2}, and Mg(OH){sub 2}. Calcium silicate hydrate minerals such as tobermorite and xonotlite were also generated. X-ray powder diffraction suggested the presence of amorphous materials. Leaching tests at various pHs revealed that the concentration of heavy metals in the leachates from MSWI bottom ash hydrothermally treated with SiO{sub 2} and Mg(OH){sub 2} was lower than that in leachates from non-treated bottom ash, especially under acid conditions. Hydrothermal treatment with modification of chemical composition may have potential for the recycling of MSWI bottom ash.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Well-Defined Nanoparticle Electrocatalysts for the Refinement of Theory

The relationship between experiment and theory in electrocatalysis is one of profound importance. Until fairly recently, the principal role of theory in this field was interpreting experimental results. Over the course of the past decade (roughly the period covered by this review), however, that has begun to change, with theory now frequently leading the design of electrocatalytic materials. Though rewarding, this has not been a particularly easy union. For one thing, experimentalists and theorists have to come to grips with the fact that they rely on different models. Theorists make predictions based on individual, perfect structural models, while experimentalists work with more complex and heterogeneous ensembles of electrocatalysts. As discussed in this review, computational capabilities have improved in recent years, so that theory is better represented by the structures that experimentalists are able to prepare. Likewise, synthetic chemists are able to make ever more complex electrocatalysts with high levels of control, which provide a more extensive palette of materials for testing theory. Finally, the goal of this review is to highlight research from the last ~10 years that focuses on carefully controlled electrocatalytic experiments which, in combination with theoretical predictions, bring us closer to bridging the gap between real catalysts and computational models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Rapid Adaptation of Chemical Named Entity Recognition Using Few-Shot Learning and LLM Distillation

Named entity recognition (NER) has been widely used in chemical text mining for the automatic identification and extraction of chemical entities. However, existing chemical NER systems primarily focus on scenarios with abundant training data, requiring significant human effort on annotations. This poses challenges for applications in the chemical field, such as catalysis, where many advancements have traditionally relied on trial-and-error investigations and incremental adjustment of variables. This hinders catalysis science and technology progress in addressing emerging energy and environmental crises. In this work, we propose a few-shot NER model that can quickly adapt to extract new types of chemical entities by using only a limited number of annotated examples. Our model employs a metric-learning approach to transfer entity similarity knowledge from high-resource chemical domains (with abundant annotations) to enable effective entity recognition in low-resource specialized domains (limited annotation). We validate the effectiveness of our model on a few-shot chemical NER benchmark built based on six existing chemical NER data sets. Experiments show that the proposed few-shot NER model can achieve reasonable performance with only 5 examples per entity type and shows consistent improvement as the number of examples increases. Furthermore, we demonstrate how the proposed model can be trained with large language model (LLM) annotated data, opening a new pathway for rapid adaptation of NER systems. Furthermore, our approach leverages the knowledge broadness of large language models for chemistry while distilling this knowledge into a lightweight model suitable for efficient and in-house use.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Molecular Level Understanding of How Oxygen and Carbon Monoxide Improve NOx Storage in Palladium/SSZ-13 Passive NOx Adsorbers: The Role of NO+ and Pd(II)(CO)(NO) Species

Addition of molecular oxygen to NO-containing stream improves NOx storage of the Pd/H-SSZ-13. Model Pd/SSZ-13 with high dispersion of Pd ions (0.1 and 1 wt% Pd) was synthesized. The material was characterized with FTIR and cryo-STEM. Adsorption of NO leads to the formation of Pd(II)-NO and Pd(I)-NO complexes as well as NO+ species that replace residual H+ (extra framework) sites. These nitrosyl species are characterized by notable thermal stability, with resistance to decomposition under high vacuum at 200 ºC. Addition of O2 to NO slightly increases the amount of Pd(II)-NO complex with ?NO at ~1865 cm-1 whereas the low frequency ?NO band at 1805 cm-1, assigned to Pd(I)-NO, decreases in intensity. Simultaneously, polydentate nitrate species appear in small amounts, contributing to the high temperature NOx release stage during a PNA cycle. The concentration of NO+ (characterized by the broad IR band centered at 2170 cm-1), in the presence of O2, increases in intensity profoundly and contributes to the increased capacity of Pd/SSZ-13 to store NOx and release it at temperatures >140 ºC. In the presence of H2O/O2, Pd/SSZ-13 does not perform satisfactorily as PNA, but the addition of CO to the stream improves the PNA storage capacity and shifts the NOx release peak temperature to >320 ºC where SCR catalysts are the most effective. With the aid of FTIR spectroscopy, we reveal the selective formation of a mixed carbonyl-nitrosyl complex Pd(II)(NO)(CO) in the presence of CO. Due to shielding of the Pd(II) ion from excess water and selective formation of stable coordinately saturated Pd(NO)(CO) complexes, the PNA performance is improved by CO. Therefore, we demonstrate that beside NO species adsorbed on Pd, nitrosyl ions (NO+) in extra framework positions of chabazite are important for PNA storage. Furthermore, the important role of CO in promoting PNA performance is elucidated, thus highlighting the utility of the combined spectroscopic approach (in addition to materials performance testing) to derive structure/PNA performance relationships and identify new avenues to improve the PNA performance.

Khivantsev, Konstantin↗

On Disrupting the Na + -Ion/Vacancy Ordering in P2-Type Sodium–Manganese–Nickel Oxide Cathodes for Na + -Ion Batteries

An investigation of the electrochemical and structural properties of layered P2-Na 0.62 Mn 0.75 Ni 0.25 O 2 is presented. The effect of changing the Mn:Ni ratio (3:1) from what is found in Na 0.67 Mn 0.67 Ni 0.33 O 2 (2:1) and consequently the introduction of a third metal center (Mn 3+ ) was investigated. X-ray diffraction ( in-situ and powder) revealed the lack of Na+-ion/vacancy ordering at the relevant sodium contents (x = 0.33, 0.5 and 0.67). The Mn 3+ in Na 0.62 Mn 0.75 Ni 0.25 O 2 introduces defects into the Ni-Mn inter-plane charge order that in turn disrupts the ordering within the Na-plane. The material underwent a P2-O2 and P2-P2’ phase transition at high (4.2 V) and low (~ 1.85 V) voltages, respectively. The material was tested at several different voltage ranges in order to understand the effect of the phase transitions on the capacity retention. Interestingly, the inclusion of both phase transitions demonstrated comparable cycling performance to when both phase transitions were excluded. As a result, excellent rate performance was demonstrated between 4.3 – 1.5 V with a specific capacity of 120 mAh/g delivered at 500 mA/g current density.

25 ENERGY STORAGE↗

Distinct Mechanism of Anti-Corrosion and Swelling-Adhesion Modeling of Low-Dimensional Nylon-Fluoropolymer Composite Coatings

Compared to other polymers, composite coatings with fluoropolymers as the matrix have attracted considerable interest due to their mechanical performance, chemical stability, and low surface energy. Herein, we present an anticorrosion mechanism of fluoropolymer composite coatings achieved by dispersing varying amounts of polyamide 12 (PA-12) particles over a poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) matrix. The choice of PVDF-HFP as a coating matrix was driven by its superior processability and mechanical properties over Teflon, while PA-12 afforded swelling capacity, preventing electrolyte permeation, and inhibiting matrix stress crack propagation. The corrosion resistance of the coatings was assessed mainly by potentiodynamic polarization and impedance measurements while being immersed in a NaCl solution. Our electrochemical measurement findings showed that 0.75% w/w PA-12 in the PVDF-HFP matrix significantly enhanced corrosion protection even after 21 days of immersion. Microscopy, dielectric spectroscopy, surface analysis, and mechanical testing (American Society for Testing and Materials standards) corroborated the results. PVDF-HFP coatings containing a minimum percolation threshold of 0.75 wt % PA-12 with 1 mil thickness on mild steel exhibited a remarkable increase in resistance and film adhesion, and a notable corrosion rate decrease. Finite element analysis simulation with a bilinear traction-separation law confirmed the swelling mechanism and adhesion behavior. Finally, this study highlights the potential of nylon particle dispersion in PVDF-HFP matrices as a practical approach to developing advanced anticorrosion coatings with promising practical applications in various industries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanoscale Engineering of Efficient Oxygen Reduction Electrocatalysts by Tailoring the Local Chemical Environment of Pt Surface Sites

The oxygen reduction reaction is the limiting half-reaction in hydrogen fuel cells. While Pt is the most active single component electrocatalyst for the reaction, it is hampered by high cost and low reaction rates. Most research to overcome these limitations has focused on Pt/3d alloys, which offer higher rates and lower cost. Here, we have synthesized, characterized, and tested alloy materials belonging to a multilayer family of electrocatalysts. The multilayer alloy materials contain an AuCu alloy core of precise composition, surrounded by Au layers and covered by a catalytically active Pt surface layer. Their performance relative to that of the commercial Pt standards reaches up to 4 times improved area-specific activity. Characterization studies support the hypothesis that the activity improvement originates from a combination of Au–Pt ligand effects and local strain effects manipulated through the AuCu alloy core. The approach we present to control the strain and ligand effects in the synthesis of Pt-based alloys for the ORR is very general and could lead to promising alloy materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Stabilization of Electrocatalytic Metal Nanoparticles at Metal-Metal Oxide-Graphene Triple Junction Points

Carbon-supported metal catalysts are widely used in heterogeneous catalysis and electrocatalysis. In this paper, we report a novel method to deposit metal catalysts and metal oxide nanoparticles on two-dimensional graphene sheets to improve the catalytic performance and stability of the catalyst materials. The new synthesis method allows indium tin oxide (ITO) nanocrystals to be directly grown on functionalized graphene sheets forming the ITO-graphene hybrids. Pt nanoparticles are then deposited to form a special triple-junction structure (Pt-ITO-graphene). Both experimental study and periodic density functional theory calculations show that the supported Pt nanoparticles are stable at Pt-ITO-graphene triple junction points. The new catalyst materials were tested for oxygen reduction for potential applications in polymer electrolyte membrane fuel cells, and they exhibited greatly enhanced stability and activity. The reasons for the high stability and activity of Pt-ITO-graphene are analyzed.

30 DIRECT ENERGY CONVERSION↗

Standardizng Data

To enable the rational design of nanomaterials for improved efficacy and safety, it is critical to understand and exploit the physicochemical properties that drive biological behavior (Morris, 2010). Data mining and computer simulation are essential for deriving information about nanomaterial behavior; however, the datasets needed to support such studies are sparse and stored across a variety of repositories and resources. Schrurs and Lison (2012) have expressed the need for more coherence and structure in the conduct of nanotechnology research. Additionally, the lack of common reporting standards and non-uniformity of information reported have proven to be significant barriers to such data sharing and re-use. The Nanotechnology Working Group (Nano WG), of the US National Institutes of Health National Cancer Informatics Program, has been focused on addressing these barriers. The Nano WG - which includes representatives from over 20 organizations including government agencies, academia, industry, standards organizations, and alliances -has developed ISA-TAB-Nano (Thomas et al, 2013), a general framework for representing and integrating diverse types of data related to the description and characterization of nanomaterials. Recognizing that nanoparticle characterization studies have many of the same challenges as ‘omics-based assays, the Nano WG joined the ISA Commons (Sansone et al., 2012) to leverage lessons learned in ‘omics data sharing. The ISA Commons community brings together 50 collaborators at over 30 scientific organizations around the globe, including regulatory and industrial participants in an increasingly diverse set of life science domains. At the core of the ISA Commons is the ISA metadata tracking framework which forms the basis for the ISA-TAB-Nano extension. The extension of the ISA framework to nanotechnology domain illustrates the power of a synergistic approach that seeks the interoperability of data across multiple research disciplines. To increase adoption, especially in the commercial arena from vendors and manufactures, the ISA-Tab-Nano data-sharing specification has also been submitted for consideration as a standard to the American Society for Testing and Materials (ASTM). Delivering a community-driven specification is only the first phase of the process. To be useful and used, ISA-TAB-Nano must be implemented by tools and databases to assist researchers in reporting their data accordingly, shielding them from unnecessary complexity. Our next step is to extend the open source ISA Software Suite to provide user-oriented tools for the collection, curation, and storage of data compliant with the ISA-TAB-Nano specification. Future work will also focus on the application of the ISA-TAB-Nano format to support emerging standards on minimal information about nanomaterials in biological research (Ostraat et al, 2012; MinChar). ISA-TAB-Nano development is a community-driven effort and we welcome new contributions, collaborations and domain expertise. We invite researchers, software developers, vendors, and other stakeholders to work with us to implement the ISA-Tab-Nano format in their existing systems and research. Likewise, we welcome engagement of regulators, funding agencies, editors, and other policy makers to discuss how this standard can be used to facilitate the sharing and reuse of nanotechnology data across a wide range of disciplines. More information about the ISA-TAB-Nano project can be found online at https://wiki.nci.nih.gov/display/ICR/ISA-TAB-Nano.

informatics↗

Understanding the Cu-Zn brass alloys using a short-range-order cluster model: Significance of specific compositions of industrial alloys

Metallic alloys show complex chemistries that are not yet understood so far. It has been widely accepted that behind the composition selection lies a short-range-order mechanism for solid solutions. The present paper addresses this fundamental question by examining the face-centered-cubic Cu-Zn a-brasses. A new structural approach, the cluster-plus-glue-atom model, is introduced, which suits specifically for the description of short-range-order structures in disordered systems. Two types of formulas are pointed out, [Zn-Cu 12 ]Zn 1,6 and [Zn-Cu 12 ](Zn,Cu) 6 , which explain the a-brasses listed in the American Society for Testing and Materials (ASTM) specifications. In these formulas, the bracketed parts represent the 1 st -neighbor cluster, and each cluster is matched with one to six 2 nd -neighbor Zn atoms or with six mixed (Zn,Cu) atoms. Such a cluster-based formulism describes the 1 st - and 2 nd -neighbor local atomic units where the solute and solvent interactions are ideally satisfied. The Cu-Ni industrial alloys are also explained, thus proving the universality of the cluster-formula approach in understanding the alloy selections. The revelation of the composition formulas for the Cu-(Zn,Ni) industrial alloys points to the common existence of simple composition rules behind seemingly complex chemistries of industrial alloys, therefore offering a fundamental and practical method towards composition interpretations of all kinds of alloys.

36 MATERIALS SCIENCE↗

In-situ Experiments to Capture the Evolution of Microstructure During Phase Transformation of Titanium Under Dynamic Loading

Under sufficient stresses, such as during dynamic loading, titanium experiences a phase transformation from hcp alpha phase to hexagonal omega phase. Omega phase is often retained in the microstructure after unloading, and has a strong influence on subsequent mechanical properties. Simulations suggest there are multiple pathways and underlying mechanisms for this transformation. Due to the incredibly short timescales involved, experimental measurements for model validation have been difficult. However, new capabilities at the Advanced Photon Source have enabled diffraction measurements during plate impact experiments to study the evolution of titanium during transformation. These high-rate data allow us to probe the mechanism and kinetics of phase transformations in new ways. Recent results will be presented and compared to post-mortem characterization of soft-recovered shocked specimens. Comparisons are then made with previous tests where material was shock-loaded and soft recovered for microstructural analysis. Together these techniques create a consistent picture of material behavior during the shock-induced α–ω phase transformation in titanium.

36 MATERIALS SCIENCE↗

Strip-based Scintillation Detector for Dual-readout High-granularity Calorimetry

New calorimeter technology is being developed for future collider experiments. We are developing a calorimeter that integrates two technologies, a high-granularity calorimeter and a dual-readout calorimeter, and has high time resolution at a picosecond level. The proposed calorimeter is a sampling calorimeter based on scintillation and Cherenkov detectors with high-granularity readout. The Cherenkov detector has a picosecond level time resolution. For the high-granularity scintillation detector, scintillator strips of 300mm × 30mm ×3mm-thick are aligned horizontally and vertically to realize an effective 30mm-square-cell segmentation. Prototype strips with different designs and scintillator materials were tested to compare the performance.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Different approaches for the development of low-cost CO{sub 2} adsorbents

Different carbon materials were tested as precursors for the production of CO{sub 2} adsorbents. The chemical modification of the surface of the prepared adsorbents was studied by means of three different approaches: impregnation with amines, electrophilic aromatic substitution, and heat treatment in the presence of ammonia. The samples were chemically characterized and the porous texture was evaluated from the N{sub 2} adsorption isotherms at -196 {sup o}C. The CO{sub 2} adsorption capacities of the adsorbents at 25 and 100 {sup o}C were evaluated in a thermogravimetric analyzer. In general, the incorporation of basic nitrogen functionalities enhanced the CO{sub 2} capture capacities of the modified carbons, but this increase depended on the textural properties of the support and the surface modification methodology. CO{sub 2} adsorption capacities of up to 111 mg CO{sub 2}/g at room temperature were attained. All the tested samples were completely regenerated when subjected to heat treatment at 100{sup o}C under inert atmosphere.

01 COAL, LIGNITE, AND PEAT↗