Search NASA⌕ Search

SEARCH · Search NASA

Results for “High current density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

INVESTIGATING SCALING LIMITS OF A FIBER BASED RESONANT PROBE FOR METROLOGY APPLICATIONS

Currently, Inertial Confinement Fusion (ICF) and High Energy Density Science (HEDS) targets comprise components with dimensions in the millimeter range, while having micrometerscale, high aspect ratio functional features, including fill-tube holes and counterbores, slotted patterns, and step-joint geometry on hemispherical targets. Representative geometry is shown in Figure 1. Future target designs will likely have additional challenging features. The dimensional metrology of these features is important for a number of reasons, including quantifying geometrical tolerances of as-built components prior to delivery, qualification of sub-components prior to assembly, and as a feedback mechanism for fabrication process development. Variations in geometry from part to part can lead to functional limitations, such as limited flow rates during target filling, unpredictable instabilities during an experiment, and the inability to assemble a target from poorly matched sub-components. Adding to the complexity are the large number and variety of materials, components, and shapes that render any single metrology technique difficult to use with low uncertainty. Adapting standing wave probe technology [i] for micrometer sized features requires the understanding of the physical interaction between the oscillating, slender rod (probe) and the sample as a means of transferring information about the surface, such as topography and material properties, analogous to tapping mode atomic force microscopy (AFM) and/or instrumented indentation machines. By utilizing the variation in dynamic response of the probe as the tip interacts with a surface, information about the sample may be obtained and used for mapping surface topography, and potentially characterizing material properties. The novel long aspect ratio geometry of the probe enables the characterization of features such as small holes, slots, and corners, which typically cannot be accessed using AFM and instrumented indentation technology. Uncertainty of the surface location is a combination of near surface effects such as van der Waals and electrostatic forces combined with contact force such adhesion and meniscus contributions. In addition, environmental effects, such as thermal gradients and air turbulence, will influence probe performance and repeatability. A combination of complex nonlinear models of the tuning fork driver/sensor mechanics, fiber dynamics, circuit response and contact interactions have been developed for the current scale system in an effort to predict scaling limitations of this technology for characterizing micrometer sized features with nanometer sensitivity.

42 ENGINEERING↗

Laser Crystallization and Dopant Activation of a-Si:H Carrier-Selective Layer in TOPCon Si Solar Cells

Herein, we present a pulsed-laser processing method for crystallization and dopant activation of a highly n-doped amorphous silicon (a-Si:H) carrier-selective layer in a tunnel oxide passivated contact (TOPCon) Si solar cell structure. Here, the laser method provides enhanced conductivity and implied open circuit voltage while reducing emitter saturation current density and surface heating, as opposed to conventional high-temperature furnace annealing of the bulk Si wafer with a TOPCon structure. We identify an appropriate laser wavelength, fluence, and layer thickness using modeling and simulations. Raman and Hall effect measurements demonstrate increased crystallinity and dopant activation, whereas photoconductive decay shows enhanced surface and interface passivation quality. Additionally, we examine the role of subsequent SiNx deposition on further improving the passivation of laser-processed TOPCon layers to achieve a 5.9 kΩ/sq film sheet resistance, 2 ms effective carrier lifetime, 718 mV implied open-circuit voltage (iVOC), and 8.6 fA/cm 2 one-side recombination current density (J0) with the potential for further passivation improvement via laser process and a-Si layer thickness optimization.

14 SOLAR ENERGY↗

All-solid-state asymmetric supercapacitor based on porous cobalt selenide thin films

As a significant semiconductor material, cobalt selenide has enormous potential and extensive application prospects in the field of solar cells, photocatalysis and supercapacitor. In this paper, porous CoSe thin films were successfully fabricated on stainless-steel sheet using a facile, effective electrodeposition technique. Electrochemical tests reveal that the specific capacitance reaches as high as 510 F g –1 at the current density of 1 A g –1 with the capacitance retention of 91% over 5000 cycles. An asymmetric all-solid-state supercapacitor is fabricated using CoSe thin film as the positive electrode and activate carbon as the negative electrode. The combined solid device displays a high area specific capacitance of 18.1 mF cm –2 accompanied with good cycling stability, outstanding flexibility and satisfactory mechanical stability. Furthermore, the solid devices connected in series can power the red light-emitting diodes. Here, the results show great potential for preparing large scale high energy density storage systems.

25 ENERGY STORAGE↗

Requirements for regional short-haul air service and the definition of a flight program to determine neighborhood reactions to small transport aircraft

An evaluation of the current status and future requirements of an intraregional short haul air service is given. A brief definition of the different types of short haul air service is given. This is followed by a historical review of previous attempts to develop short haul air service in high density urban areas and an assessment of the current status. The requirements for intraregional air service, the need for economic and environmental viability and the need for a flight research program are defined. A detailed outline of a research program that would determine urban community reaction to frequent operations of small transport aircraft is also given. Both the operation of such an experiment in a specific region (San Francisco Bay area) and the necessary design modifications of an existing fixed wing aircraft which could be used in the experiment are established. An estimate is made of overall program costs.

Feher, K.↗

Highly dense atomic Fe–Ni dual metal sites for efficient CO 2 to CO electrolyzers at industrial current densities

Carbon-supported, atomically dispersed, nitrogen-coordinated metal sites (e.g., Fe and Ni) are arguably the most promising catalysts for the electrochemical reduction of CO 2 to CO due to their unique catalytic properties and the use of earth-abundant elements. However, conventional single metal sites are constrained by their structural simplicity, causing either too weak or too strong absorption/desorption of multiple critical intermediates (e.g., *COOH and *CO). Current catalysts also suffer from ultra-low loadings (<1.0 wt%) of atomic metal active sites in catalysts, leading to inadequate performance for CO 2 -to-CO conversion. Here, we develop dual Ni/Fe metal site catalysts with significantly increased atomically dispersed metal loadings (up to 4.8 wt%). A gas-phase chemical vapor deposition (CVD) approach to introducing single Ni sites was integrated with Fe 2 O 3 /ZIF-8 precursors, followed by an optimal thermal activation. The optimized CVD-Ni/Fe–N–C catalyst exhibited remarkable electrocatalytic performance for the CO 2 reduction to CO in a continuous membrane-electrode-assembly electrolyzer, achieving a maximum CO faradaic efficiency (FE CO ) of 96% at a current density of 700 mA cm −2 in a near-neutral electrolyte. Furthermore, a desirable but challenging acidic flow-cell electrolyzer was designed using this dual metal site catalyst to improve CO 2 utilization, accomplishing a FE CO of up to 95% at a CO partial current density close to 600 mA cm −2 . Density functional theory (DFT) calculations suggest a synergetic effect between Fe–Ni pairs facilitating *COOH intermediate formation and *CO desorption simultaneously during CO 2 to CO conversion. This is key to breaking the linear scaling relationship of conventional single-metal site catalysts during the CO 2 reduction reaction.

36 MATERIALS SCIENCE↗

Fundamental Studies of Tritium Solubility and Diffusivity in LiAlO 2 and Lithium Zirconates Pellets Used in TPBAR

Using atomistic level calculations, in this study, we propose to investigate the solubility and diffusivity properties of hydrogen isotopes in the blanket candidate materials (e.g. Li 2 O, LiAlO 2 , Li 2 ZrO 3 , Li 6 Zr 2 O 7 , Li 8 ZrO 6 , Li 4 SiO 4 , etc.) for TPBARs to enable tritium production in PWRs and to improve the performances of these components. With the knowledge of $3\atop{1}$T transport, the potential impact of the candidate performance mechanisms of the pellet materials can be evaluated computationally. Using results from our previously performed research on the electronic and thermodynamic properties of these ceramic materials, we will study the $3\atop{1}$T diffusivity and solubility in the abovementioned lithium ceramic materials. Lithium zirconates are stable at very high temperatures and have high densities and ion conductivities. These materials can also be used as pellets which may result in a better overall performance in TPBAR. Lithium zirconates contain lithium-rich phases, such as Li 6 Zr 2 O 7 , Li 8 ZrO 6 , which may result in a high 6 Li density to minimize the 6 Li enrichment. The focus of current research is to identify the mechanisms associated with atomic $3\atop{1}$T formation, diffusion, transport, deposition, and the kinetics at high temperature. For these purposes, we will employ first-principles density functional theory (DFT) and molecular dynamics (MD) simulations to perform our investigations.

07 ISOTOPE AND RADIATION SOURCES↗

Electrochemical Carbon Monoxide Reduction on Polycrystalline Copper: Effects of Potential, Pressure, and pH on Selectivity toward Multicarbon and Oxygenated Products

Here by understanding the surface reactivity of CO, which is a key intermediate during electrochemical CO 2 reduction, is crucial for the development of catalysts that selectively target desired products for the conversion of CO 2 to fuels and chemicals. In this study, a custom-designed electrochemical cell is utilized to investigate planar polycrystalline copper as an electrocatalyst for CO reduction under alkaline conditions. Seven major CO reduction products have been observed including various hydrocarbons and oxygenates which are also common CO 2 reduction products, strongly indicating that CO is a key reaction intermediate for these further-reduced products. A comparison of CO and CO 2 reduction demonstrates that there is a large decrease in the overpotential for C–C coupled products under CO reduction conditions. The effects of CO partial pressure and electrolyte pH are investigated; we conclude that the aforementioned large potential shift is primarily a pH effect. Thus, alkaline conditions can be used to increase the energy efficiency of CO and CO 2 reduction to C–C coupled products, when these cathode reactions are coupled to the oxygen evolution reaction at the anode. Further analysis of the reaction products reveals common trends in selectivity that indicate both the production of oxygenates and C–C coupled products are favored at lower overpotentials. These selectivity trends are generalized by comparing the results on planar Cu to current state-of-the-art high-surface-area Cu catalysts, which are able to achieve high oxygenate selectivity by operating at the same geometric current density at lower overpotentials. Combined, these findings outline key principles for designing CO and CO 2 electrolyzers that are able to produce valuable C–C coupled products with high energy efficiency.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Selective and Stable Ethanol Synthesis via Electrochemical CO 2 Reduction in a Solid Electrolyte Reactor

Electrochemical CO 2 reduction to ethanol faces challenges such as low selectivity, a product mixture with liquid electrolyte, and poor catalyst/reactor stability. Here, we developed a grain-rich zinc-doped Cu 2 O precatalyst that presented a high ethanol Faradaic efficiency of over 40% under a current density of 350 mA·cm –2 . Our density functional theory (DFT) simulation suggested that Zn atoms inside the structure have a greater carbophilicity than the Cu atoms to help facilitate *CHCHO formation, a key reaction intermediate toward ethanol instead of other C 2 products. Here, a high Faradaic efficiency ratio between ethanol and ethylene (FE EtOH /FE C2H4 ) reached 2.34 in the zinc-doped Cu 2 O precatalyst, representing an over 4-fold improvement compared to bare Cu 2 O precatalyst. By integrating this Cu-based catalyst into a porous solid electrolyte (PSE) reactor with a salt-managing design, we achieved stable ethanol production for over 180 h under a current density of 250 mA·cm –2 while maintaining ethanol selectivity at ~30%.

09 BIOMASS FUELS↗

Modification of Ni-Rich FCG NMC and NCA Cathodes by Atomic Layer Deposition: Preventing Surface Phase Transitions for High-Voltage Lithium-Ion Batteries

The energy density of current lithium-ion batteries (LIBs) based on layered LiMO 2 cathodes (M=Ni, Mn, Co: NMC; M=Ni, Co, Al: NCA) needs to be improved significantly in order to compete with internal combustion engines and allow for widespread implementation of electric vehicles (EVs). In this report, we show that atomic layer deposition (ALD) of titania (TiO 2 ) and alumina (Al 2 O 3 ) on Ni-rich FCG NMC and NCA active material particles could substantially improve LIB performance and allow for increased upper cutoff voltage (UCV) during charging, which delivers significantly increased specific energy utilization. Our results show that Al2O3 coating improved the NMC cycling performance by 40% and the NCA cycling performance by 34% at 1C/₋1C with respectively 4.35V and 4.4V UCV in 2Ah pouch cells. High resolution TEM/SAED structural characterization revealed that Al 2 O 3 coatings prevented surface-initiated layered-to-spinel phase transitions in coated materials which were prevalent in uncoated materials. Lastly, EIS confirmed that Al 2 O 3 -coated materials had significantly lower increase in the charge transfer component of impedance during cycling. In conclusion, the ability to mitigate degradation mechanisms for Ni-rich NMC and NCA illustrated in this report provides insight into a method to enable the performance of high-voltage LIBs.

25 ENERGY STORAGE↗

An Anode-Free Zn–MnO 2 Battery

Aqueous Zn-based batteries are attractive because of the low cost and high theoretical capacity of the Zn metal anode. However, the Zn-based batteries developed so far utilize an excess amount of Zn (i.e., thick Zn metal anode), which decreases the energy density of the whole battery. In this study, we demonstrate an anode-free design (i.e., zero-excess Zn), which is enabled by employing a nanocarbon nucleation layer. Electrochemical studies show that this design allows for uniform Zn electrodeposition with high efficiency and stability over a range of current densities and plating capacities. Using this anode-free configuration, we showcase a Zn–MnO 2 battery prototype, showing 68.2% capacity retention after 80 cycles. Our anode-free design opens a new direction for implementing aqueous Zn-based batteries in energy storage systems.

25 ENERGY STORAGE↗

Ambient Rare Earth Metal Electrodeposition in Nitrogen-Coordinated Silylamide Electrolyte

The transition to a sustainable, low-carbon economy demands energy-efficient and environmentally benign methods for rare earth metal (REM) production. Furthermore, while high-temperature molten salt electrolysis remains energy-intensive, corrosive, and environmentally unfriendly, emerging room-temperature processes based on conventional ionic liquids are also hindered by high viscosity and chemical instability. In this study, a nitrogen-coordinated, water-, oxygen-, and fluorine-free silylamide-based electrolyte is presented as a promising system for room-temperature REM electrodeposition. Derived from commercially available lithium silylamide precursors, the system enables facile synthesis, broad electrochemical stability, and tunable metal–ligand interactions. Electrochemical analysis reveals high voltammetric stripping reversibility, stable cathodic and anodic potentials, and selective neodymium (Nd) deposition at appreciable current densities (>1 mA/cm 2 ), with minimal parasitic reactions. Bulk experiments produced high-purity Nd with reproducible performance across multiple batches. Scaled deposition yielded over 1 g of Nd with near-theoretical mass efficiency (0.40 mg/C) and >90% purity. Using sacrificial dysprosium (Dy) and Nd metal anodes, the system maintained constant Nd loading during extended deposition and enabled cathodic codeposition of stripped anode material, demonstrating the electrolyte’s dual functionality for REM electrorefining. Collectively, this silylamide platform offers a compelling combination of electrochemical robustness, chemical resilience, and process scalability for sustainable ambient REM recovery.

36 - MATERIALS SCIENCE↗

Preface to special topic: The High Repetition Rate Frontier in High-Energy-Density Physics

High-repetition-rate (HRR) experiments can collect large datasets with high temporal, spatial, and/or parametric resolution or large numbers of repeat measurements for statistics. HRR experiments also enable new experimental designs, including active feedback control loops and novel diagnostics, that can improve the reproducibility as well as the quantity of measurements. Together, these attributes make HRR experiments ideal for performing high-quality repeatable science. Until recently, these techniques have not been applied to high-energy-density–physics (HEDP) experiments, which are typically restricted to repetition rates of a few per day. However, recent advancements in lasers, pulsed-power drivers, target fabrication, and diagnostics are starting to change this fact, opening an exciting new frontier of HRR HEDP experiments. A mini-conference on this subject at the 2021 meeting of the American Physical Society Division of Plasma Physics brought together members of this growing community. As a result, the “High Repetition Rate Frontier in High-Energy-Density Physics” special topic in Physics of Plasmas highlights current progress in this exciting area.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Engineering Nanocolumnar Defect Configurations for Optimized Vortex Pinning in High Temperature Superconducting Nanocomposite Wires

High temperature superconducting (HTS), coated conductor wires based on nanocomposite films containing self-assembled, insulating BaZrO3 (BZO) nanocolumnar defects have previously been reported to exhibit enhanced vortex pinning. Here, we report on microstructural design via control of BZO nanocolumns density in YBa2Cu3O7- (YBCO)+BZO nancomposite films to achieve the highest critical current density, Jc(H, ,T). X-ray diffraction and microstructural examination shows increasing number density of epitaxial BZO nanocolumns in the highly cube-textured YBCO matrix with increasing nominal BZO additions. Transport property measurement reveals that an increase in BZO content upto 4 vol% is required to sustain the highest pinning and Jc performance as the magnetic field increases. By growing thicker, single-layer nanocomposite films (~4 m) with controlled density of BZO columnar defects, the critical current (Ic) of ~1000 A/cm at 77 K, self-field and the minimum Ic of 455 A/cm at 65 K and 3 T for all magnetic field orientations were obtained. This is the highest Ic reported to date for films on metallic templates which are the basis for the 2nd generation, coated conductor-based HTS wires.

critical current density↗

High Density Chip Interconnect Technology Using High Density Glass Interposers

Demands for high density and high speed interconnect solutions are not satisfied by current technology offerings. Platforms such as printed circuit boards (PCBs), ceramic substrates and silicon interposers don’t provide the small form factor nor the I/O density to support 5G or 1Tbps gigabit ethernet solutions. Current solutions also don’t support die to die assembly with integrated tiled solutions for wide area and fanout solutions for lager data and signal processing. A solution with through vias provides an order of magnitude or smaller density supporting much higher density attach and assembly By fabricating a very fine pitch metal filled through glass via solution it’s possible to deliver the necessary improvements in performance, reliability, even higher data speed rates with smaller area and much denser geometries. There are a number of opportunities across a wide variety of industries for through glass interposers as they become the replacement for printed circuit boards (PCBs) and ceramic substrates. The broad array of opportunities include renewable energy, medical electronics (ME), defense electronics (DE)/space and consumer electronics (CE), but likely will impact every industry and market segment. Compared to PCBs, through glass via (TGV) solutions provide the next generation platform for semiconductor assembly improvements. The ability to generate lines, spaces, trenches and vias similar to wafer level geometries delivers wired solutions one to two orders of magnitude smaller than traditional organic PCB and ceramic substrate offerings. Higher density connections also include the thru vias that connect multiple metal layers, fanout. It’s possible to deliver filled metal vias that are 20um diameter with much tighter pitch than can be offered with PCB. Our goal is to provide 20um diameter and smaller via, 50um and smaller pitch, and aspect ratios at 25:1 and greater with hermetically metal filled vias. The goal of CVI is to replace or eliminate PCBs, ceramic substrate and through silicon vias (TSV) providing a glass interposer with metal filled, fiber plugged and/or optional wireless interconnectivity. The end plan is to deliver a glass substrate platform that provides improved electrical performance, versatility, inertness, and much improved cost and cycle time (development, drawing, and delivery) to performance in the form of small millimeter sized substrates or full 8” wafer substrates. Glass delivers an improvement over silicon thru vias (TSV) in the number of processing steps, cost, reliability and cycle time. In addition to metal plugged vias, our glass interposers are capable of fiber and antennae solutions providing two additional very high density and ultra-high speed data transfer capabilities.

36 MATERIALS SCIENCE↗

Wettable carbon felt framework for high loading Li-metal composite anode

Li metal anode has received extensive attention due to its high specific capacity and low potential vs. Li/Li + for lithium batteries. However, dendrite growth, volume change and "dead" Li formation during cycling hinder its practical application. Here we report an innovated cuprite-coated carbon felt as current collector, with ultralight 3D framework and significantly improved Li-metal loading through thermal infusion. The Li-metal anode has a high Li content of 90 wt.%. The cuprite coating improves the lithiophilicity of carbon felt remarkably, due to the surface affinity reaction between cuprite and Li. Moreover, the porous carbon felt provides good electronic connection and buffer space to accommodate volume change during Li stripping/plating. It leads to uniformly distributed local current density and preference of Li stripping/plating in the highly dispersed concave areas, with suppressed formation of dendrites and “dead” Li. The Li composite electrode shows excellent cycle stability with low polarization in both symmetric and full cells. Hence, this work opens a new approach for the development of high loading Li composite anodes for advanced Li metal batteries.

25 ENERGY STORAGE↗

Coronal streamers in the solar wind at 1 AU

Virtually all solar wind observing groups have reported substantial variations in the solar wind helium-hydrogen abundance ratio (A(He)). A study of Los Alamos Imp solar wind data has revealed an association between low A(He) and high proton density that occurs at low flow speeds and that is correlated with polarity reversals of the interplanetary magnetic field. The current investigation has the objective to present further examples of the low A(He), high proton density, low speed, magnetic field polarity association, and to document the common occurrence of multiple events lasting approximately 3-7 days. The results are presented of attempts to relate these events directly to maps or isophotes of solar coronal brightness at 1.5 solar radii. The results of the investigation suggest that a substantial fraction of the low-speed solar wind originates in coronal streamers, particularly near solar minimum.

Gosling, J. T.↗

Ambipolar zinc-polyiodide electrolyte for a high-energy density aqueous redox flow battery

Large-scale energy storage systems are crucial for substantial deployment of renewable energy sources. Energy storage systems with high energy density, high safety, and low cost and environmental friendliness are desired. To overcome the major limitations of the current aqueous redox flow battery systems, namely lower energy density (~25 Wh L -1 ) and presence of strong acids and/or other hazardous, a high energy density aqueous zinc/polyiodide flow battery (ZIB) is designed with near neutral ZnI 2 solutions as catholytes. The energy density of ZIB could reach 322 Wh L -1 at the solubility limit of ZnI 2 in water (~7 M). We demonstrate charge and discharge energy densities of 245.9 Wh/L and 166.7 Wh L-1 with ZnI 2 electrolyte at 5.0 M, respectively. The addition of ethanol (EtOH) in ZnI 2 electrolyte can effectively mitigate the growth of zinc dendrite at the anode and improve the stability of catholytes with wider temperature window (-20 to 50°C), which enable ZIB system to be a promising alternative as a high-energy and high- safety stationary energy storage system.

25 ENERGY STORAGE↗

Additive Manufacturing of Multifunctional Components Using High Density Carbon Nanotube Yarn Filaments

Additive manufacturing allows for design freedom and part complexity not currently attainable using traditional manufacturing technologies. Fused Filament Fabrication (FFF), for example, can yield novel component geometries and functionalities because the method provides a high level of control over material placement and processing conditions. This is achievable by extrusion of a preprocessed filament feedstock material along a predetermined path. However if fabrication of a multifunctional part relies only on conventional filament materials, it will require a different material for each unique functionality printed into the part. Carbon nanotubes (CNTs) are an attractive material for many applications due to their high specific strength as well as good electrical and thermal conductivity. The presence of this set of properties in a single material presents an opportunity to use one material to achieve multifunctionality in an additively manufactured part. This paper describes a recently developed method for processing continuous CNT yarn filaments into three-dimensional articles, and summarizes the mechanical, electrical, and sensing performance of the components fabricated in this way.

Gardner, John M.↗