Search NASA⌕ Search

SEARCH · Search NASA

Results for “Structural components”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81

Investigation of Ionic Liquids Isolated Iron for Ductile Iron Castings

As research continues for missions beyond low-Earth orbit, in-situ resource utilization (ISRU) methods are critical. For Lunar and Martian colonization, the ability to manufacture mechanical and structural components with local resources is essential. Ionic liquids (IL) are being studied at NASA Marshall Space Flight Center (MSFC) to harvest elemental metals from meteorites and regolith oxides. In this investigation, the viability of casting ductile iron using ionic liquids sourced iron and nickel was explored given ductile iron’s range of applications and performance as an as-cast alloy. Ingots were produced using commercial elements to simulate the use of IL iron with carbon sourced from the by-products of a life support system currently tested at MSFC. Samples were cast and compared to commercial ductile iron with phase transformation diagrams,microstructures, and hardness. Results showed ionic liquids sourced elements are a viable source of elemental alloying materials for a range of ductile iron alloys.

Ionic Liquids↗

Al-Cu-Zn-Mg Alloy for Additive Manufacturing by Electron Beam Deposition

The application of fusion-based additive manufacturing (AM) to aircraft structural components is limited by the lack of high-strength aluminum alloys optimized for AM processing. High strength aluminum alloys (such as 7050-T7451) are difficult to process by AM because of their solidification cracking susceptibility and loss of volatile alloying elements such as Zn and Mg. The performance of a proprietary Al-Cu-Zn-Mg alloy wire feedstock was evaluated for AM utilizing electron beam deposition. Deposit microstructure, composition, occurrence of porosity and cracking, and post-heat treatment tensile and fracture toughness were correlated with deposition parameters. Post-heat treatment strength, ductility, and fracture toughness were lower than typical values for wrought 7050-T7451, related to significant losses of Zn and Mg and to porosity. Recommendations are offered for modifications to wire feedstock composition and adjustments to deposition conditions and heat treatment to enable AM of electron beam deposited material that has strength comparable to 7050-T7451 wrought products.

Al-Cu-Zn-Mg alloy, electron beam deposition, mecha↗

Additive Manufacture of Porous ZrC for NTP In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Omar Mireles↗

Developing a Set of Indicators to Identify, Monitor, and Track Impacts and Change in Forests of the United States

United States forestland is an important ecosystem type, land cover, land use, and economic resource that is facing several drivers of change including climatic. Because of its significance, forestland was identified through the National Climate Assessment(NCA) as a key sector and system of concern to be included in a system of climate indicators as part of a sustained assessment effort. Here, we describe 11 informative core indicators of forests and climate change impacts with metrics available or nearly available for use in the NCA efforts. The recommended indicators are based on a comprehensive conceptual model which recognizes forests as a land use, an ecosystem, and an economic sector. The indicators cover major forest attributes such as extent, structural components such as biomass, functions such as growth and productivity, and ecosystem services such as biodiversity and outdoor recreation. Interactions between humans and forests are represented through indicators focused on the wildland-urban interface, cost to mitigate wildfire risk, and energy produced from forest-based biomass. Selected indicators also include drought and disturbance from both wildfires and biotic agents. The forest indicators presented are an initial set that will need further refinement in coordination with other NCA indicator teams. Our effort ideally will initiate the collection of critical measurements and observations and lead to additional research on forest-climate indicators.

U.S. forests↗

Additive Manufacture of Porous Zirconium Carbide for Nuclear Thermal Propulsion In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Zirconium Carbide Additive Manufacture↗

Additive Manufacture of Porous Zirconium Carbide for Nuclear Thermal Propulsion In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Zirconium Carbide Additive Manufacture↗

Multifunctional Surface Treatment for Self-Sterilization and CO2 Sequestration for Sustainable Space Exploration

A long-term human space presence is dependent on maintaining a safe living environment. Disinfecting surfaces is essential to protecting astronauts from potential pathogens, as well as structural components of the habitat from damaging biofilms. Developing a surface coating that utilizes readily available light has the potential to provide sterilization with additional functionality. Titanium dioxide (TiO2) is a commonly used photocatalyst owing to its efficiency, economic feasibility, and safety to humans. TiO2 photocatalyst modified with other metals such as copper or iron could allow for self-sterilization, photocatalytic memory, and photoreduction of carbon dioxide (CO2) to fuels on Mars. Sustainable design of the photocatalyst should account for the resources available, specifically within the Martian and Lunar regolith. This project reviews the current technologies to design a TiO2 photocatalyst which can be incorporated into a space habitat’s inner lining.

Human Space Exploration↗

B Complex 5-Methyltetrahydrofolate, Riboflavin, Pyridoxine, and Methylcobalamin Supplementation as a Non-Mechanical Countermeasure to Mitigate Optic Disc Edema Changes During Strict 6º Head-Down Tilt Bed Rest

A subset of astronauts on International Space Station missions have experienced optic disc edema, part of what is characterized as Spaceflight Associated Neuro-ocular Syndrome (SANS). While the precise cause of SANS is unknown, it is likely that there are multiple contributing factors, including genetic and environmental factors. Our recent work has shown that crewmembers with SANS have higher concentrations of metabolic biomarkers of impairments in the one-carbon metabolic pathway compared to unaffected astronauts - before, during, and after f light (1). B-vitamin status and the presence of one-carbon pathway single nucleotide polymorphism (SNP) variants predicted the incidence of SANS pathologies, including optic disc edema (2). Specifically, the G allele of methionine synthase reductase (MTRR) A66G and the C allele of serine hydroxymethyltransferase-1 (SHMT1) C1420T were associated with increased incidence of SANS pathologies (2). In a recent 30-d bed rest head-down tilt study with 0.5% CO2 exposure, 5 of 11 subjects developed optic disc edema (4) and the same SHMT1 C1420T and MTRR A66G genetic variants were associated with a larger increase in total retina thickness, a quantitative measure of optic disc edema (5). We published a multi-hit hypothesis of how genetics represents an indispensable element of SANS, which is a multifactorial problem (6). In brief: endothelial dysfunction secondary to genetic, biochemical/nutritional, and physiological (e.g., cardiovascular/fluid shift) f actors could lead to optic disc edema and the other ocular changes that occur in SANS. We expanded this hypothesis to include the possibility that genetic effects on B-vitamin status can alter nitric oxide synthesis and oxidative stress in the endothelium. This in turn could alter the turnover of structural components of the sclera, making it more susceptible to pathologic changes when faced with stressors related to the unrelenting headward fluid shift that occurs in weightlessness and strict head-down tilt bed rest (5). If the relationships that we have observed in flight and ground-based research hold true for the SANS Countermeasure Study, these genetic factors could predict who will be more susceptible to the development of SANS, and more importantly could also provide countermeasure options. As has been shown extensively in the literature, vitamin supplementation can serve to overcome genetic hindrances to one-carbon biochemistry and vascular physiology. Thus, based on our findings, publications, and hypotheses, supported by extensive supporting literature, we had hoped to test in the SANS Countermeasure Study the efficacy of a bioactive B-vitamin complex as a countermeasure to optimize function of the one-carbon pathway and prevent or mitigate optic disc edema during strict 6-degree head down tilt bed rest, and ultimately in space f light. While the supplement is no longer planned to be tested in the SANS Countermeasure Study because of laws regulating supplementation studies like this costing much more than initially planned, we will assess the contribution of one-carbon pathway genetics and B-vitamin status to SANS risk.

S R Zwart↗

Metallic Environmentally Resistant Coating Rapid Innovation Initiative

Lightweight alloys such as aluminum (Al) and titanium (Ti) are often specified for space systems to minimize mass while maintaining structural integrity [1,2]. Such alloys however, have poor tribological response (high friction and wear), especially in extreme space environments, which becomes worse with the additional presence of lunar regolith. This leads to short lifetimes and premature failures that will ultimately limit long term operations on the lunar surface [2]. This project is addressing this technology gap by developing advanced wear- and radiation-resistant coatings for lightweight parts to extend the life-time and sustainability of both lunar and Martian assets. Ceramics were considered for their high wear resistance, but were rejected because of their low fracture toughness, which would be especially problematic for structural components. The novel and existing coating technologies and deposition methods are being tested in this project. The coating materials are Boron Nitride-Aluminum (BN-Al), Nickle Titanium (NiTi), Aluminum Oxide (AlO3), Ti64 with hBN at 2 and 10 vol percent (Ti-2vol%hBN and Ti-10vol%hBN), and the deposition techniques are high pressure cold-spray (CS) and ambient and vacuum plasma-spray (APS and VPS) [3,4,5]. BN-Al, NiTi, Ti-2vol%hBN, and Ti-10vol%hBN were applied with all three deposition techniques, and AlO3 was applied only using the APS deposition technique. A tungstenite (WS2) film was applied to the NiTi VPS coating. The coating and deposition technique configurations are being tested against several key end-use performance parameters. The parameters include the capabilities of the coatings under wear environments such as regolith simulant, thermal cycling from high (120°C) to cryogenic (-173°C), high vacuum (~10-7 torr), and pre- and post-exposure to ionizing particle radiation. Wear tests include pin on disk, three-body abrasion, and surface erosion by high velocity regolith impacts. The initial down selection is being performed using on virgin and environmental exposure samples using pin on disk and three body abrasion wear tests. From preliminary assessment of this testing, a few configurations were eliminated. Ti-10vol%hBN could not be applied using CS application and NiTi could not be applied using APS or CS application so these configurations did not get tested. Early pin on disk wear tests showed poor wear performance of BN-Al so this coating was eliminated early in the testing process. AlO3 on Al substrate did not survive thermal cycling, but wear testing is continuing for AlO3 on Ti substrate. A more detailed analysis is being con-ducted to further reduce the number of configuration for phase II and III. Phase II testing will include conventionally and additively manufactured substrates with surface erosion testing. In phase III, the coatings will be applied to three mechanism types: channel and slot, ball and socket, and a hinge joint. Each will demonstrate a different type of wear incidence. The mechanisms and their base materials are of direct interest to the end users and infusion points: the Human Landing System (HLS) and the Lunar Surface Innovation Initiative (sustained lunar surface operations). The technology development project is based out of Marshall Space Flight Center, has partnered with Florida International University (Miami, FL) and Plasma Processes (Huntsville, Al), and is supported by a group of NASA mentors from different centers.

dust mitigation↗

Linear and Geometrically Nonlinear Structural Shape Sensing from Strain Data

An aircraft’s shape must be measured during flight to implement active shape controls such as active trim shape, divergence, and sonic boom controls. A basis function method for linear as well as geometrically nonlinear structural shape sensing is proposed in this study. Basis functions can be mode shapes, linear static deformation shapes, and/or geometrically nonlinear static deformation shapes. The proposed basis function method is validated using a high-aspect-ratio wing, a swept test plate, and the National Aeronautics and Space Administration X-59 aircraft. A large structural deformation of a high-aspect-ratio wing is successfully captured using the proposed basis function method with less than 0.3%prediction error at the wing-tip section. The basis function method gives excellent deformation prediction, even with stress concentration. Performance of the basis functions is compared using the X-59 stabilator sample case. In most of the sample load cases, static deformations give a better correlation with the target deformation than do mode shapes. Wing shape sensing with sparse strain data are also demonstrated in this study using the X-59 aircraft. Predicted structural deformations match reasonably with the target deformations, even without strain gauges on some structural components. The predicted deformations have a good match with the target deformations.

Static Deformation↗

Structural Shape Sensing from Strain Data Using the Basis Function Method

An aircraft shape must be measured during flight to implement an active trim shape control, such as an active dihedral control for a highly flexible aircraft with a high-aspect-ratio wing, and an active sonic boom control for a supersonic transport aircraft. A basis function method for linear as well as geometrically nonlinear structural shape sensing is proposed in this study. Basis functions can be mode shapes, linear static deformation shapes, or geometrically nonlinear static deformation shapes. The proposed basis function method is validated using a high-aspect-ratio wing, a swept test plate, and the National Aeronautics and Space Administration Low Boom Flight Demonstration mission X-59 Quiet Supersonic Technology (QueSST) aircraft (Lockheed Martin, Bethesda, Maryland). A large structural deformation of a high-aspect-ratio wing is successfully captured using the proposed basis function method with less than 0.3-percentprediction error at the wing-tip section. The basis function method gives excellent deformation prediction, even with stress concentration. Performance of the basis functions is compared using the X-59 stabilator sample case. In most of the sample load cases, static deformations give a better correlation with the target deformation than do mode shapes. Wing shape sensing with sparse strain data is also demonstrated in this study using the X-59 QueSST aircraft. Predicted structural deformations match reasonably with the target deformations even without strain gauges on some structural components. The predicted deformations have a good match with the target deformations.

Chan-gi Pak↗

Radiation Shielding Plasma Sprayed Coatings Heads to International Space Station for MISSE-17 Experiments

NASA's Artemis program aims to return to the moon in search of scientific discoveries and establish a habitat using in-situ resource utilization. However, the past lunar explorations presented challenges, such as thermal cycles, solar and intergalactic cosmic radiation, and severe abrasive interaction of sharp lunar regolith particles[1]–[4].Dust mitigation and radiation shielding have become the most important concerns for lunar structural components and rovers which can fail abruptly without a protective solution. To counter these threats, Plasma Forming Laboratory(PFL) at Florida International University (FIU), in collaboration with NASA, has developed a novel multi-functional coating to protect the components synergistically against abrasion, erosion ,and radiation. The titanium-boron nitride composite coatings were prepared using the atmospheric plasma spray technique from engineered composite powders [5], [6].The coatings were subjected to extensive characterization and tribological study with lunar mare simulant JSC-1A, which shows tremendous improvement in the wear performance. The coatings subjected to neutron radiation shielding experiments at NASA Langley Research Center exhibited significantly improved neutron attenuation capacity compared to the substrate. The coating is selected to undergo radiation exposure on the International Space Station as a part of MISSE-17 (Materials International Space Station Experiment).

Thermal Spray↗

Development of Aluminum Feedstock for Additive Manufacturing

The rapid evolution of materials science and manufacturing technologies in recent years has offered new pathways to manipulate materials for bespoke manufacturing. Here we aim to develop feedstocks for applications such as radiator panels, fuel tanks, and structural components for outfitting. As a strong, light weight and thermally conductive material aluminum is ideal for these applications. An often-overlooked source of aluminum waste is food packaging used on the International Space Station. Reusing this waste stream will reduce the cost and logistics of regular sparing. In Space Manufacturing (ISM) will utilize this technology is such areas as sparing and outfitting. However, processing aluminum can present challenges, especially in the context of additive manufacturing and sintering, due to its high reactivity and tendency to form a tenacious oxide layer. Identifying appropriate binders and sintering profiles can overcome these challenges. Herein we present our work on obtaining aluminum powder derived from food packaging, binder selection for aluminum feedstock, and a demonstration of bound metal deposition printing.

aluminum↗

Wear and Neutron Shielding Resilience of Titanium-Hexagonal Boron Nitride Coatings Against Extreme Lunar Radiation and Thermal Cycles

Ti6Al4V and Al6061 are aerospace alloys used in lunar structural components and rovers owing to their high specific strength. However, they deteriorate rapidly when subjected to demanding conditions of the lunar environment, such as extreme thermal cycles, solar particle radiation, and abrasive regolith. Cryo-milled powders were employed to deposit hBN-reinforced protective titanium coatings through plasma spray (atmospheric APS and vacuum-VPS) with 2 and 10 vol% of hBN on Ti6Al4V and Al6061 substrates. These coatings were evaluated for durability under extreme lunar-like conditions, including thermal cycling, electron radiation, and synergistic (electron radiation-thermal cycle) exposure. The coatings exhibited radiation-induced hardening, resulting in a substantial increase in their microhardness ~20–40% compared to virgin condition. Bright-field transmission electron microscopy (TEM) analysis reveals the presence of high dislocation densities, black dot defects, and dislocation clusters, providing evidence of the severe impact of synergistic environmental stresses. Ball-on-disk tribological tests were conducted in the presence of JSC-1 A lunar regolith simulant to evaluate the wear performance of coatings. Compared to conventional Ti6Al4V substrate, 50%, 90%, and 70% reductions in wear volume were observed in the Ti/2 vol% hBN coatings in thermal-only, radiation-only, and synergistic environments. Neutron shielding tests indicate that the synergistic coatings offer higher neutron shielding performance by up to 28% compared to virgin coatings, attributed to improved neutron capture by 10B isotopes. Upon a comprehensive assessment and ranking of multiple coatings under varying conditions, the VPS Ti/2 vol% hBN coating emerges as the top choice for protection against extreme radiation and thermal cycles for future lunar explorations.

Boron nitride↗

Manufacturing Process Development of a Carbon Fiber Reinforced Polymer Composite Shaft for Electric Motors

Electric aircraft applications require electric motors with increased specific power and efficiency. Composite structural components in motors are a potential solution for reducing motor mass, reducing magnetic losses, and limiting undesired conduction paths for fault, electromagnetic interference, or common-mode currents. In this report, manufacturing trials for a high-speed carbon fiber reinforced polymer composite motor shaft are presented. Four prototype shafts were produced using a hybrid biaxial/triaxial fabric that was circumferentially wrapped onto an additively manufactured high-temperature washout mandrel. An additional traditional overbraid approach was also evaluated and shows promise for high-rate, high-performance parts using automated manufacturing. This paper discusses the shaft design, manufacturing methods explored, material selection, the manufacturing trials, and the lessons learned. The results of this manufacturing investigation show feasibility for manufacturing composite shafts for electric motors.

Electric moto shaft↗

Erosion Behavior of Ti-hBN Multifunctional Coatings in A Custom-Made Planetary Test Rig at Extreme Lunar Temperatures

Spacecraft landings and takeoffs on the lunar surface, along with extreme temperature variations between day and night (-196 to 150° C), cause high-velocity dust impacts and erosion, resulting in the premature failure of structures. Ti/2 vol% hBN coatings were deposited using atmospheric (APS) and vacuum plasma spray (VPS) using cryo-milled powder feedstock to protect the structural components. The erosion performance of coatings at extreme lunar temperature regimes (-150 to 150° C) was evaluated in a custom-made planetary erosion test rig (PETR) at low (50 mph) and high impact velocities (250 mph). The mass loss of VPS coatings was reduced by 50% compared to the APS coatings and 40% compared to the Ti6Al4V substrate. The cryogenic temperature induces brittleness in the material, rendering it susceptible to extreme conditions of material loss. The particle impact-deformation behavior was captured using a high-speed camera to study the erosion mechanism. This analysis revealed chipping in substrates and brittle APS coatings, while particles rebounding and embedding were observed in VPS coatings. Energy calculations, aided by particle trajectory tracking from the high-speed camera, have conclusively shown that VPS coatings absorb 5–10% more energy than APS coatings during erosion tests. A modified erosion index was developed incorporating the fracture toughness and temperatures. New erosion models for brittle and ductile target materials are proposed for developing erosion-resistant material systems.

Abhijith Kunneparambil Sukumaran↗

Development of a Forced-Convection Liquid-Fluoride-Salt Test Loop

A small forced-convection molten-fluoride-salt loop is being constructed at Oak Ridge National Laboratory to examine the heat transfer behavior of FLiNaK salt in a heated pebble bed. Objectives of the experiment include reestablishing infrastructure needed for fluoride-salt loop testing, developing a unique inductive heating technique for performing heat transfer (or other) experiments, measuring heat transfer characteristics in a liquid-fluoride-salt-cooled pebble bed, and demonstrating the use of silicon carbide (SiC) as a structural component for salt systems. The salt loop will consist of an Inconel 600 piping system, a sump-type pump, a SiC test section, and an air-cooled heat exchanger, as well as auxiliary systems needed to pre-heat the loop, transport salt into and out of the loop, and maintain an inert cover gas over the salt. A 30,000 Hz inductive heating system will be used to provide up to 250 kW of power to a 15 cm diameter SiC test section containing a packed bed of 3 cm graphite spheres. A SiC-to-Inconel 600 joint will use a conventional nickel/grafoil spiral wound gasket sandwiched between SiC and Inconel flanges. The loop system can provide up to 4.5 kg/s of salt flow at a head of 0.125 MPa and operate at a pressure just above atmospheric. Pebble Reynolds numbers of up to 2600 are possible with this configuration. A sump system is provided to drain and store the salt when not in use. Instrumentation on the loop will include pressure, temperature, and flow measurements, while the test section will be instrumented to provide pebble and FLiNaK temperatures.

36 MATERIALS SCIENCE↗

Fabrication Flaw Density and Distribution in Piping Weldments

The U.S. Nuclear Regulatory Commission supported the Pacific Northwest National Laboratory (PNNL) to develop empirical data on the density and distribution of fabrication flaws in nuclear reactor components. These data are needed to support probabilistic fracture mechanics calculations and studies on component structural integrity. PNNL performed nondestructive examination inspections and destructive testing on archived piping welds to determine the fabrication flaw size and distribution characteristics of the flaws in nuclear power plant piping weldments. Eight different processes and product forms in piping weldments were studied including wrought stainless steel and dissimilar metal weldments. Parametric analysis using an exponential fit was performed on the data. Results were created as a function of the through-wall size of the fabrication flaws as well as the length distribution. The results are compared and contrasted with those developed for reactor pressure vessel processes and product forms. The most significant findings were that the density of fabrication flaws versus through-wall size was higher in piping weldments than that for the reactor pressure vessel weldments, and the density of fabrication flaws versus through-wall size in both reactor pressure vessel weld repairs and piping weldments were greater than the density in the original weldments. Curves showing these distributions are presented.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗