Search NASA⌕ Search

SEARCH · Search NASA

Results for “Carbides”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

Thermal conductivity and Seebeck coefficients of icosahedral boron arsenide films on silicon carbide

The thermal conductivity of icosahedral boron arsenide (B{sub 12}As{sub 2}) films grown on (0001) 6H-SiC substrates by chemical vapor deposition was studied by the 3{omega} technique. The room temperature thermal conductivity decreased from 27.0 to 15.3 W/m K as the growth temperature was decreased from 1450 to 1275 deg. C. This is mainly attributed to the differences in the impurity concentration and microstructure, determined from secondary ion mass spectrometry and high resolution transmission electron microscopy, respectively. Callaway's theory was applied to calculate the temperature-dependent thermal conductivity, and the results are in good agreement with the experimental data. Seebeck coefficients were determined as 107 {mu}V/K and 136 {mu}V/K for samples grown at 1350 deg. C with AsH{sub 3}/B{sub 2}H{sub 6} flow ratio equals to 1:1 and 3:5, respectively.

36 MATERIALS SCIENCE↗

Interdiffusion in W/Si Multilayers with Boron Carbide Interlayers

W/Si multilayers with B{sub 4}C as a diffusion barrier were deposited using ion beam sputtering technique. It was found that incorporation of B{sub 4}C at both interfaces of Si enhances the reflectivity of the multilayer. Though the interface of W/Si or W/B{sub 4}C has been studied in literature, what happens at Si/B{sub 4}C interfaces is largely unknown. This is primarily due to absence of contrast between Si/B{sub 4}C for x-rays. For neutrons there is significant contrast between Si and B{sub 4}C, therefore we used neutron reflectivity to study thermal stability of Si/B{sub 4}C multilayers. It was found that up to an annealing temperature of 573 K, the multilayer remains intact however at higher temperature interdiffusion starts.

36 MATERIALS SCIENCE↗

Atomistic simulations of the mechanical properties of silicon carbide nanowires

Molecular dynamics methods using the Tersoff bond-order potential are performed to study the nanomechanical behavior of [111]-oriented β-SiC nanowires under tension, compression, torsion, combined tension-torsion and combined compression-torsion. Under axial tensile strain, the bonds of the nanowires are just stretched before the failure of nanowires by bond breakage. The failure behavior is found to depend on size and temperatures. Under axial compressive strain, the collapse of the SiC nanowires by yielding or column buckling mode depends on the length and diameters of the nanowires, and the latter is consistent with the analysis of equivalent continuum structures using Euler buckling theory. The nanowires collapse through a phase transformation from crystal to amorphous structure in several atomic layers under torsion strain. Under combined loading the failure and buckling modes are not affected by the torsion with a small torsion rate, but the critical stress decreases with increasing the torsion rate. Torsion buckling occurs before the failure and buckling with a big torsion rate. Plastic deformation appears in the buckling zone with further increasing the combined loading.

36 MATERIALS SCIENCE↗

Response of Nanocrystalline 3C Silicon Carbide to Heavy-Ion Irradiation

Nanostructured materials are generally believed to be more radiation resistant. This study reports on Au ion induced amorphization in nanocrystalline 3C-SiC, characterized using x-ray diffraction, transmission electron microscopy and Raman spectroscopy. Full amorphization at room temperature occurs at a comparable dose to that for bulk SiC single crystals. The behavior is attributed to a high ion flux and sluggish migration of point defects produced during irradiation. The results may have a significant implication of using nanophased SiC in extremely high radiation environments.

36 MATERIALS SCIENCE↗

Combined experimental and computational study of the recrystallization process induced by electronic interactions of swift heavy ions with silicon carbide crystals

The healing effect of intense electronic energy deposition arising during swift heavy ion (SHI) irradiation is demonstrated in the case of 3C-SiC damaged by nuclear energy deposition. Experimental (ion channeling experiments) and computational (molecular dynamics simulations) studies provide consistent indications of disorder decrease after SHI irradiation. Furthermore, both methods establish that SHI-induced recrystallization takes place at amorphous-crystalline interfaces. The recovery process is unambiguously accounted for by the thermal spike phenomenon.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Transition from Irradiation-Induced Amorphization to Crystallization in Nanocrystalline Silicon Carbide

Response to irradiation of nanocrystalline 3C-SiC is studied using 2 MeV Au+ ions near the critical temperature for amorphization and is compared to the behavior of its monocrystalline counterpart under the identical irradiation conditions. The irradiated samples have been characterized using in-situ ion channeling, ex-situ x-ray diffraction, and helium ion microscopy. Compared to monocrystalline 3C-SiC, a faster amorphization process in the nanocrystalline material (average grain size = 3.3 nm) is observed at 500 K. However, the nanograin grows with increasing ion fluence at 550 K and the grain size tends to saturate at high fluences. The striking contrast demonstrates a sharp transition from irradiation-induced interface-driven amorphization at 500 K to crystallization at 550 K. The results could show potential impacts of nanocrystalline SiC on nuclear fuel cladding and structural components of next-generation nuclear energy systems.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Comparative study of changes in electrical properties of silicon and silicon carbide upon proton irradiation

Rates of carrier removal from the conduction band in n-type FZ-Si and 4H-SiC irradiated with 8- and 15-MeV protons at room temperature are discussed. Calculated rates of formation of primary radiation defects (Frenkel pairs) in these materials are presented and compared with the corresponding experimental values. Protons create defects in collision cascades involving recoil atoms formed in the crystal lattice itself. The results are compared with similar data previously obtained in irradiation of n-type FZ-Si and 4H-SiC with 900-keV electrons, in which case isolated so-called close Frenkel pairs are absolutely dominant among primary radiation defects. It has been found that the E-center model adequately describing the decrease in the electrical conductivity of n-FZ-Si upon electron irradiation is inapplicable to interpretation of experimental data for proton-irradiated materials. It is suggested that a pronounced annealing of 'simple' radiation defects of the type of close Frenkel pairs occurs during irradiation at room temperature.

36 MATERIALS SCIENCE↗

Fabrication of heterostructures based on layered nanocrystalline silicon carbide polytypes

The study demonstrates the possibility of forming heterostructures consisting of nanocrystalline SiC layers of the cubic 3C polytype (the lower layer on the substrate) and the rhombohedral 21R polytype (the upper layer) by direction deposition of nanocrystalline SiC layers onto a substrate subjected to gradient heating. The structure and order of arrangement of the SiC layers are analyzed in detail by X-ray diffraction studies, femtosecond photoluminescence measurements, and optical spectroscopy. The nature of the peaks observed in the photoluminescence, optical reflectance, and absorption spectra is discussed.

36 MATERIALS SCIENCE↗

Corrosion Investigation of Zinc–Aluminum Alloy (ZA-27) Matrix Reinforced with In Situ Synthesized Titanium Carbide Particle Composites

ZA-27 alloy matrix composites comprised of different volume fractions of TiC particles as reinforcement phase were synthesized by in situ technique. Microstructural, hardness and electrochemical analysis were performed on these samples along with the base ZA-27 alloy to assess any beneficial effect of making the composites over the base alloy. It was observed that hardness increases in composites as compared to the base alloy. However, hardness of the composite reduces on increasing the reinforcement percentage. Corrosion behavior was investigated by using Tafel and EIS plots in 3.5 wt.% NaCl solution at room temperature for all the samples. The results showed increase in corrosion resistance for composites than that of base alloy. However, ZA27 + 5%TiC composite showed better results as compared to that of ZA27 + 10%TiC composite. The decreased property of ZA27 + 10%TiC composite is because of the agglomeration of particles and also by the formation of galvanic cell.

36 MATERIALS SCIENCE↗

Load partitioning in honycomb-like silicon carbide aluminum alloy composites.

A 50/50 vol.% Al/SiC composite was made via melt infiltration of an aluminum alloy into a porous beech wood-derived SiC preform. The honeycomb-like composite microstructure consisted of an interconnected SiC phase surrounding discrete Al 'fibers' aligned in the growth direction of the beech wood. High energy synchrotron X-ray diffraction was used to measure the volume averaged lattice strains in both the SiC and Al phases during in situ compressive loading up to an applied stress of -530MPa. Load transfer from the Al to the SiC was observed, and the Al yielded at an applied stress of above -213MPa. The elastic behavior of the composite was modeled with both an isostrain rule of mixtures calculation and variational bounds for the effective elastic modulus. Furthermore, calculations of the von Mises effective stress of the SiC and Al phases showed that the wood-derived SiC was a more effective reinforcement than either SiC particle- or whisker-reinforced composites.

09 BIOMASS FUELS↗

Tensile and compressive mechanical behavior of twinned silicon carbide nanowires

Molecular dynamics simulations with the Tersoff potential were used to study the response of twinned SiC nanowires under tensile and compressive strains. The critical strain of the twinned nanowires can be enhanced by twin-stacking faults, and their critical strains are larger than those of perfect nanowires with the same diameters. Under axial tensile strain, the bonds of the nanowires are just stretched before failure. The failure behavior is found to depend on the twin segment thickness and the diameter of the nanowires. An atomic chain is observed for the thin nanowires with small twin segment thickness under tension strain. Under axial compressive strain, the collapse of the twinned SiC nanowires exhibits two differently failure modes, depending on the length and diameter of the nanowires, i.e. shell buckling for short length nanowires and columnar buckling for longer length nanowires.

36 MATERIALS SCIENCE↗

Strength, deformation, and equation of state of tungsten carbide to 66 GPa

Here, strength, texture, and equation of state of hexagonal tungsten monocarbide (WC) have been determined under quasi-hydrostatic and non-hydrostatic compression to 66 GPa using angle-dispersive X-ray diffraction in the diamond anvil cell. Quasi-hydrostatic compression in a Ne pressure medium demonstrates that nanocrystalline WC is slightly less incompressible than bulk-scale WC, with respective bulk moduli of K 0 = 377 ± 7 and 397 ± 7 GPa and pressure derivatives K 0 ’ = 3.8 ± 0.3 and 3.7 ±0.3. This decrease in incompressibility with grain size is similar to behavior observed in other ceramics. Under nonhydrostatic compression, WC supports a mean differential stress of ~12-15 GPa at plastic yielding, which occurs at ~30 GPa. Strength in WC is anisotropic, with the (001) plane supporting 29-42% higher stress than stresses calculated from mean strain. Simulations using an Elasto-ViscoPlastic Self-Consistent model indicate that strength inferred from lattice strain theory may be overestimated due to effects of plastic deformation. Plastic deformation generates a texture maximum near $\langle\bar{2}110\rangle$ in the compression orientation, initially through prismatic slip on the {$10\bar{1}0$}$\langle\bar{1}2\bar{1}0\rangle$ and {$10\bar{1}0$}$\langle0001\rangle$ slip systems, followed by activation of pyramidal slip on {$10\bar{1}1$}$\langle\bar{2}113\rangle$ at ~40-50 GPa.

36 MATERIALS SCIENCE↗

High-temperature active oxidation of nanocrystalline silicon-carbide: A reactive force-field molecular dynamics study

Flexible woven SiC ceramics are prone to accelerated fiber embrittlement under high temperature oxidation in dynamic oxygen environments. The nanocrystalline structure of the constituent fibers impacts the reaction kinetics and phase transformations during active oxidation. However, fundamental understanding and quantification of grain boundary effects on oxidation behavior in nanocrystalline SiC remain elusive when temperatures exceed 1500 K. This study deploys large-scale molecular dynamics simulations with a reactive force-field to elucidate the complex roles of atomic oxygen reservoir conditions and grain size on oxidation kinetics and the nature of oxides produced in both monocrystalline and nanocrystalline 3C-SiC between 1100 K and 2000 K. The simulations with dynamically replenished oxygen provide good agreement with oxidation kinetics and activation energies for the monocrystalline Si(100) and C(100) orientations published in the available literature. This study reveals that, by contrast, nanocrystalline SiC samples exhibit two distinct oxidation kinetics with a transition point at 1500 K due to surface melting, which is supported by experimental evidence. The introduction of a grain-boundary network produces a two-fold decrease in oxidation activation energies compared to monocrystalline SiC below 1500 K. Above 1500 K, however, the activation energies rise substantially due to the formation of a liquid Si phase at the SiC/Si oxide interface. Further, it is shown that the stability of the interfacial liquid phase is promoted by incoherent grain boundaries in the crystalline SiC. These findings are important for the deployment of nanocrystalline SiC fibers in advanced thermal protection systems for high-temperature applications.

36 MATERIALS SCIENCE↗

Fuel performance of chromium-coated zirconium alloy and silicon carbide accident tolerant fuel claddings

The U.S. Department of Energy’s Accident Tolerant Fuel program is focused on extending the time for fuel failure during postulated severe accidents compared to the standard UO2-Zr alloy fuel system. This research investigates the feasibility of two different chromium-coated cladding concepts, one of which is zirconium-alloy based and the other is composite-SiC based. Both claddings had 50µm coatings, deducted from the base layer thicknesses. The claddings were reported on, using the multi- physics fuel performance tool BISON, under steady-state PWR operating conditions as well as two transients: power ramp and a loss-of-coolant accident (LOCA). The chromium-coated claddings showed comparable thermo-mechanical performance to the reference Zircaloy-4 cladding. As chromium is reported to provide an order of magnitude improvement in oxidation resistance, it is expected to be a better alternative in accident scenarios. Simulation results for both concepts call for further experimental investigation as well as modeling of beyond design-basis accidents.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Transient testing of uranium silicide fuel in zircaloy and silicon carbide cladding

Using the newly restarted Transient Reactor Test (TREAT) facility at Idaho National Laboratories, fresh (unirradiated) U 3 Si 2 fuel pellets were tested under reactivity-initiated accident conditions in dry helium capsules. These tests were performed with total energy depositions sufficient to induce melting of the U 3 Si 2 fuel pellets based on available thermophysical property data. The instrumented experiments utilized in-pile thermocouples and infrared pyrometers to measure the cladding temperature during the transient, which are in reasonable agreement with predicted peak cladding temperatures using a simple BISON fuel performance model. This same model is then used to predict expected cladding stresses during the transients in areas where pellet cladding interaction is expected. It was shown that for transient energy depositions up to 528J/g rod like geometry of the test articles was maintained. While it is acknowledged that more confirmatory testing is required in more prototypic environments, these first of their kind experiments have demonstrated that unirradiated U 3 Si 2 fuel and unirradiated SiC-SiC claddings can likely retain a “rod like” geometry for transient energy depositions up to 528J/g.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fe-carbide/Fe-oxide-based nanocomposites synthesized as magnetic nanomaterials via laser ablation synthesis in solution (LASiS)

Magnetic nanostructured materials (MNMs) have gained prominence in materials technology developments owing to their potential biomedical applications for hyperthermia cancer treatment, and transplant organ cryopreservation. Herein, we report the facile and cost-effective synthesis of Fe-based composite MNMs, comprising both Fe@Fe 2 O 3 and Fe 3 C@C core-shell nanoparticles (NPs), via Laser Ablation Synthesis in Solution (LASiS) using Fe targets ablated under acetone and toluene. Detailed materials characterizations using electron microscopy-based imaging, diffraction studies, and spectroscopic analyses - including Raman and Mössbauer spectroscopy - relate the structure-composition properties for different Fe-oxide/carbide phases in the aforesaid MNMs to their respective magnetic responses. Specifically, we confirm the presence of ultra-small (2–10 nm) amorphous Fe-oxide NPs, as well as Fe@Fe 2 O 3 core-shell NPs (20–40 nm) in the samples synthesized by ablating Fe under acetone. In contrast, samples synthesized under toluene indicate a higher concentration of Fe 3 C@C core-shell NPs (20–40 nm) with a relatively low concentration of Fe 2 O 3 NPs (2–10 nm). Furthermore, the crystallinity of the metallic phases and carbonaceous shell coatings are systematically increased by carrying out LASiS under heated toluene (up to ~95 °C). Importantly, mössbauer spectroscopy results indicate that the elevation in toluene temperature leads to an increase in the concentrations of Fe 3 C@C NPs from ~40 % to ~53 % (at.).

36 MATERIALS SCIENCE↗