Search NASA⌕ Search

SEARCH · Search NASA

Results for “etching”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82

InGaN/GaN QDs Nanorods: Processing and Properties

InGaN/GaN nanorod structure is presented for the fabrication of light-emitting diodes by means of plasma-chemical etching. Processes of the etching of nanorods and the defect passivation in a planar InGaN/GaN quantum dot heterostructure are studied. The obtained results allow creating the light-emitting diode nanostructure with a greater efficiency compared to the classical planar technology.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Photoanodization of n-Si in the Presence of Hydrogen Peroxide: Voltage Dependence

The fundamental aspects of the electrochemical etching of lightly doped n-Si under backside illumination conditions are studied in a solution with a low HF concentration and a high concentration of hydrogen peroxide. The data obtained are compared with those for a control electrolyte containing no H{sub 2}O{sub 2}. The morphology of the self-organized macropores, their growth rate, porosity, effective valence, and the amount of dissolved silicon are examined in relation to the applied voltage. The anodization kinetics at low and high bias voltages is analyzed. It is found that, under the same illumination, the initial photocurrent in the peroxide electrolyte is approximately twice lower than in the aqueous electrolyte, which makes it possible to state that the quantum efficiency of the photocurrent is lower. As, however, the etching duration is made longer, the current in the peroxide electrolyte strongly increases to become higher than that in the control electrolyte based on H{sub 2}O. It is found that, in the presence of H{sub 2}O{sub 2}, the depthwise growth rate of the macropores increases by more than a factor of 2, and the porosity decreases. The vertical macropore channels have a diameter smaller than that for macropores formed in the aqueous electrolyte and their walls are poorly passivated, which causes branching and the formation of secondary mesopores, the number of which grows with increasing voltage. The effective valence of silicon dissolution in the presence of H{sub 2}O{sub 2} decreases to less than 2. The results are interpreted in terms of the Gerischer and Kolasinski models.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Silicon Nanopillar Microarrays: Formation and Resonance Reflection of Light

Abstract—The results of investigating the spectral characteristics of reflection from silicon nanopillar (Si NP) microarrays in the wavelength region from 400 to 1100 nm are presented. The Si nanopillars are formed by electron lithography on a negative resist with subsequent reactive ion etching. The Si nanopillars are etched through a resist mask and SiO{sub 2} 100 nm thick. In the spectra of reflection from nanopillar microarrays, minima are observed, the position of which depends strongly on the Si nanopillar diameter.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Oxide Removal from the InSb Plate Surface to Produce Lateral Spin Valves

Abstracts: The formation conditions of a smooth and oxide-free surface of InSb semiconductor with the purpose of fabricating lateral spin devices based on it are investigated. The dry etching rate by Ar ions of the surface of the crystalline faces (100) of InSb plates as well as a variation in their roughness depending on the power supplied to ion etching devices are investigated. The degree of oxidation of the semiconductor surface exposed to air after ion cleaning and annealing in molecular hydrogen are evaluated. Based on comparison of the efficiency of spin injection in devices formed with semiconductors subjected to various types of treatment, a conclusion is made about the parameters of optimal preparation of the surface of the InSb wafers for the fabrication of lateral spin devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ohmic Contacts to CVD Diamond with Boron-Doped Delta Layers

Various methods for the formation of ohmic contacts to boron-doped δ layers in CVD-diamond epitaxial structures are investigated. In the first variant, an additional thin heavily doped layer was formed on the diamond surface to which an ohmic contact is formed. Then, the surface p{sup +} layer between the contact pads is etched out; therefore, the current in the structure flows only through a buried δ layer. In the second approach, the doped diamond selectively grows in the contact windows under a metallic mask after preliminary etching of the undoped diamond layer (cap) up to the δ layer. In this case, the heavily doped p{sup +} layer forms an end contact to the δ layer. These two variants differ in terms of the conditions of applicability, the complexity of the manufacturing technology, the value of the contact resistance, and can be used to solve problems in which it is necessary to have a different quality of the contacts, such as the formation of transistor structures or test cells for measuring physical characteristics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Simulation of Local Error Correction of the Surface Shape by a Low-Dimensional Ion Beam

We propose an algorithm for solving the problem of local error correction of the surface shape by a low-dimensional ion beam. The algorithm presumes successive sampling running over protrusions relative to the average height aimed at searching for the optimal etching point satisfying the criterion for the reduction of the sum of derivative moduli on the etching spot. It is shown that the new approach makes it possible to considerably extend the range of spatial frequencies accessible to the action for a given dimension of an ion beam.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Performance of "Moth Eye" Anti-Reflective Coatings for Solar Cell Applications

An inexpensive, effective anti-reflective coating (ARC) has been developed at the University of Florida to significantly enhance the absorption of light by silicon in solar cells. This coating has nano-scale features, and its microstructure mimics that of various night active insects (e.g. a moth's eye). It is a square array of pillars, each about 700 nm high and having a diameter of about 300 nm. Samples of silicon having this coating were exposed either to various combinations of either elevated temperature and humidity or to gamma irradiation ({sup 60}Co) at the Savannah River National Laboratory, or to a broad spectrum ultraviolet light and to a 532 nm laser light at the University of Florida. The anti-reflective properties of the coatings were unaffected by any of these environmental stresses, and the microstructure of the coating was also unaffected. In fact, the reflectivity of the gamma irradiated ARC became lower (advantageous for solar cell applications) at wavelengths between 400 and 1000 nm. These results show that this coating is robust and should be tested in actual systems exposed to either weather or a space environment. Structural details of the ARCs were studied to optimize their performance. Square arrays performed better than hexagonal arrays - the natural moth-eye coating is indeed a square array. The optimal depth of the templated nanopillars in the ARC was investigated. A wet etching technology for ARC formation was developed that would be less expensive and much faster than dry etching. Theoretical modeling revealed that dimple arrays should perform better than nipple arrays. A method of fabricating both dimple and nipple arrays having the same length was developed, and the dimple arrays performed better than the nipple arrays, in agreement with the modeling. The commercial viability of the technology is quite feasible, since the technology is scalable and inexpensive. This technology is also compatible with current industrial fabrication of solar cells.

14 SOLAR ENERGY↗

Shear Alignment of Diblock Copolymers for Patterning Nanowire Meshes

Metallic nanowire meshes are useful as cheap, flexible alternatives to indium tin oxide – an expensive, brittle material used in transparent conductive electrodes. We have fabricated nanowire meshes over areas up to 2.5 cm 2 by: 1) mechanically aligning parallel rows of diblock copolymer (diBCP) microdomains; 2) selectively infiltrating those domains with metallic ions; 3) etching away the diBCP template; 4) sintering to reduce ions to metal nanowires; and, 5) repeating steps 1 – 4 on the same sample at a 90° offset. We aligned parallel rows of polystyrene-b-poly(2-vinylpyridine) [PS(48.5 kDa)-b-P2VP(14.5 kDa)] microdomains by heating above its glass transition temperature (T g ≈ 100°C), applying mechanical shear pressure (33 kPa) and normal force (13.7 N), and cooling below T g . DiBCP samples were submerged in aqueous solutions of metallic ions (15 – 40 mM ions; 0.1 – 0.5 M HCl) for 30 – 90 minutes, which coordinate to nitrogen in P2VP. Subsequent ozone-etching and sintering steps yielded parallel nanowires. We aimed to optimize alignment parameters (e.g. shear and normal pressures, alignment duration, and PDMS thickness) to improve the quality, reproducibility, and scalability of meshes. We also investigated metals other than Pt and Au that may be patterned using this technique (Cu, Ag).

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Micropipe Dissociation through Thick n+ Buffer Layer Growth

Thick (> 25 {mu}m) 4H n+ epitaxial layer growth was performed on 4H n+ substrates utilizing chlorine containing etch chemistries in a hot wall CVD system. Optimization of the n+ epitaxial layer growth was achieved by varying C/Si ratio and N2 flow. Desired epitaxial layers have doping levels > 5x1018 cm-3, epitaxial surface roughness <10 nm on a 20x20 {mu}m area and overall micropipe density reduction. To confirm the conversion of micropipes into closed core screw dislocations, microscopic examination of the epitaxial and wafer surfaces was carried out after KOH etching. Grazing incidence x-ray topography (XRT) as well as cross sectional XRT and microscopy were also performed. The cross sectional evaluation showed that the dissociation of the micropipes occurs very close to the epitaxy/wafer interface.

36 MATERIALS SCIENCE↗

(abstract) Mechanism of Selective Porosification at Heterojunctions in Group IV Multilayer Structures

Highly selective porosification of SiGe or Ge layers is observed in multilayer Si/SiGe or Si/Ge structures grown on (100)Si. These alternating porous/nonporous structures could potentially be used to fabricate light-emitting devices. The etch-selectivity appears to be dominated by band-structure effects and other factors such as lattice strain and electrochemical potential differences play a minor role. Additional structures and electrolytic etching are being examined to confirm these results.

porosification silicon Si Ge germanium light emitt↗

320 x 256 Complementary Barrier Infrared Detector Focal Plane Array for Long-Wave Infrared Imaging

A 320 x 256 Complementary Barrier Infrared (CBIRD) focal plane array for long-wavelength infrared (LWIR) imaging is reported. The arrays were grown by molecular beam expitaxy (MBE) with a 300 period 1.9 um thick absorber. The mean dark current density of 2.2 x 10-4 A/cm2 was measured at an operating bias of 128 mV with a long wavelength cutoff of 8.8 ?m observed at 50% of the peak. The maximum quantum efficiency was 54% measured at 5.6 ?m. Operating at T = 80K, the array yielded an 81% fill factor with 97% operability. Good imagery with a mean noise equivalent different temperature (NE?T) of 18.6 mK and a mean detectivity of D* = 1.3 x 1011 cm-Hz1/2/W was achieved. The substrate was thinned using mechanical lapping and neither an AR coating nor a passivation layer was applied. This article provides the details of the fabrication process for achieving low-dark current LWIR CBIRD arrays. Discussion for an effective hard mask for excellent pattern transfer is given and appropriate mounting techniques for good thermal contact during the dry etching process is described. The challenges and differences between etching large 200 ?m test diodes and small 28 ?m FPA pixels are given.

Focal Plane Arrays (FPA)↗

X-ray Topography to Characterize Surface Damage on CdZnTe Crystals

Synthetic CdZnTe or 'CZT' crystals can be used for room temperature detection of {gamma}-radiation. Structural/morphological heterogeneities within CZT, such as twinning, secondary phases (often referred to as inclusions or precipitates), and poly-crystallinity can affect detector performance. As part of a broader study using synchrotron radiation techniques to correlate detector performance to microstructure, x-ray topography (XRT) has been used to characterize CZT crystals. We have found that CZT crystals almost always have a variety of residual surface damage, which interferes with our ability to observe the underlying microstructure for purposes of crystal quality evaluation. Specific structures are identifiable as resulting from fabrication processes and from handling and shipping of sample crystals. Etching was found to remove this damage; however, our studies have shown that the radiation detector performance of the etched surfaces was inferior to the as-polished surface due to higher surface currents which result in more peak tailing and less energy resolution. We have not fully investigated the effects of the various types of inducible damage on radiation detector performance.

43 PARTICLE ACCELERATORS↗

Improved Performance of JLab 7-Cell Cavities by Electropolishing

The great majority of experience in niobium SRF cavity processing at Jefferson Lab is with BCP etching. This has been used on CEBAF cavities and others totalling over 600 in number. With improved process quality control, field emission is now largely controlled and other factors limit performance. All of the prototype cavities developed for the 12 GeV upgrade, although meeting minimum requirements, have demonstrated a Q-drop in the 17?23 MV/m range that is not remedied by 120 C bake. Most of these cavities received >250 micron removal by BCP etch. Two of these cavities have been electropolished using the protocol under development within ILC R&D activities. The first such cavity was transformed from Q = 3×109 at 17 MV/m to quench from 1×1010 at 35 MV/m. The details of this and subsequent electropolished JLab 7-cell cavities will be reported.

43 PARTICLE ACCELERATORS↗

X-ray Topography to Characterize Surface Damage on CdZnTe Crystals

Synthetic CdZnTe or 'CZT' crystals can be used for room temperature detection of {gamma}-radiation. Structural/morphological heterogeneities within CZT, such as twinning, secondary phases (often referred to as inclusions or precipitates), and poly-crystallinity can affect detector performance. As part of a broader study using synchrotron radiation techniques to correlate detector performance to microstructure, x-ray topography (XRT) has been used to characterize CZT crystals. We have found that CZT crystals almost always have a variety of residual surface damage, which interferes with our ability to observe the underlying microstructure for purposes of crystal quality evaluation. Specific structures are identifiable as resulting from fabrication processes and from handling and shipping of sample crystals. Etching was found to remove this damage; however, our studies have shown that the radiation detector performance of the etched surfaces was inferior to the as-polished surface due to higher surface currents which result in more peak tailing and less energy resolution. We have not fully investigated the effects of the various types of inducible damage on radiation detector performance. (authors)

36 MATERIALS SCIENCE↗

Development of pseudo-random binary gratings and arrays for calibration of surface profile metrology tools

Optical Metrology tools, especially for short wavelength (EUV and X-Ray), must cover a wide range of spatial frequencies from the very low, which affects figure, to the important mid-spatial frequencies and the high spatial frequency range, which produces undesirable flair. A major difficulty in using surface profilometers arises due to the unknown Modulation Transfer Function (MTF) of the instruments. Therefore, accurate calibration of profilometers, the understanding of their MTF limitations, and cross calibration between tools represents a considerable challenge for quantitative optical metrology. In previous work the instrumental MTF of a surface profiler was precisely measured using reference test surfaces based on binary pseudo-random (BPR) gratings. Here, they present results of fabricating and using two-dimensional (2D) BPR arrays that allow for a direct 2D calibration of the instrumental MTF. BPR sequences are widely used in engineering and communication applications such as Global Position System, and wireless communication protocol. The ideal BPR pattern has a flat 'white noise' response over the entire range of spatial frequencies of interest. The BPR array used here is based on the Uniformly Redundant Array prescription initially used for x-ray and gamma ray astronomy applications. The URA's superior imaging capability originates from the fact that its cyclical autocorrelation function very closely approximates a delta function, which produces a flat Power Spectrum Density (PSD). Three different BPR array patterns were fabricated by electron beam lithography and ICP etching of silicon. The basic size unit was 200 nm, 400 nm, and 600 nm. Figure 1 shows the fabrication sequence. The 2D BPR arrays were used as standard test surfaces for MTF calibration of the MicroMap{trademark}-570 interferometric microscope with all available objectives. Figure 2 shows representative scanning probe height data for the 400 nm BPR sample. Figure 2 shows the raw Power Spectral Density for 5 different objectives. They demonstrate that the two dimensional BPR array is a very effective calibration standard. However, departures from ideal, such as square sidewall, and uniform etch depth ultimately can limit the accuracy of the calibration. The effects of fabrication imperfections on the efficiency of calibration will be discussed.

36 MATERIALS SCIENCE↗

Micro-fabrication Techniques for Target Components

Micro-fabrication techniques, derived from the semi-conductor industry, can be used to make a variety of useful mechanical components for targets. A selection of these components including supporting cooling arms for prototype cryogenic inertial confinement fusion targets, stepped and graded density targets for materials dynamics experiments are described. Micro-fabrication enables cost-effective, simultaneous fabrication of multiple high-precision components with complex geometries. Micro-fabrication techniques such as thin-film deposition, photo-lithographic patterning and etch processes normally used in the semi-conductor manufacture industry, can be exploited to make useful mechanical target components. Micro-fabrication processes have in recent years been used to create a number of micro-electro-mechanical systems (MEMS) components such as pressure sensors, accelerometers, ink jet printer heads, microfluidics platforms and the like. These techniques consist primarily of deposition of thin films of material, photo-lithographic patterning and etching processes performed sequentially to produce three dimensional structures using essentially planar processes. While the planar technology can be limiting in terms of the possible geometries of the final product, advantages of using these techniques include the ability to make multiple complex structures simultaneously and cost-effectively. Target components fabricated using these techniques include the supporting cooling arms for cryogenic prototype fusion ignition targets, stepped targets for equation-of-state experiments, and graded density reservoirs for material strength experiments.

42 ENGINEERING↗

Quasi-single-crystal (001) SrTiO3 templates on Si

The integration of high quality multifunctional oxides on semiconductor devices requires single-crystal-like templates directly on silicon that match with thin film heterostructures. We report the fabrication of quasi-single-crystal (001) SrTiO3 templates on (001) Si by annealing MBE-grown epitaxial SrTiO3 films at 900oC in oxygen. The FWHM of (002) SrTiO3 rocking curve is less than 0.006o which is much narrower than SrTiO3 bulk single crystals. Atomically smooth TiO2-terminated surface is obtained by buffered-HF etching, which presents the possibility of creating novel oxide heterointerfaces on Si platform. Epitaxial SrRuO3 films grown on the etched template exhibit a superior crystalline quality to those grown on a untreated template and an atomically smooth surface.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗